Search Documents

By Thomas M. Keevin, Gregory L. Hempen

A study was conducted to measure underwater pressures associated with confined borehole shooting used to remove rock for The Kill Van Kull Deepening Project, U.S. Army Corps of Engineers, New York District. A major natural-resource-agency concern was the potential for fish mortality during explosive rock removal. Currently, fish mortality models are based on testing programs that exposed captured organisms to open-water blasts. Natural resource agencies, without in-house explosive engineering expertise, generally are not familiar with the physical properties of blasting underwater. Confined shots are most often used for demolition and rock removal underwater. Pressure amplitudes from confined blasts are significantly reduced as compared to open-water blasts that, are commonly used for fish testing The duties of natural resource agencies are made even more difficult by the lack of published data on pressures associated with confined blasting. As a result, explosive weights for confined shots mistakenly have been used to run mortality models that were developed using open-water blast pressure data. This study was conducted to collect pressure measurements during rock removal for the KVK deepening project and compare those data with computed peak pressures for open-water explosions.

Jan 1, 2005

By Greg Shapiro, Paul Dr. Worsey

Mining, quarry, and construction blasts are becoming more and more dependent on bench profiling. The use of accurate profiling gives the blaster better data for the most efficient blast results. So, we ask the question: What is the best method for measuring and analyzing burden?

Jan 1, 2019

By Calvin J. Konya

Backbreak behind the last row of boreholes can be a significant problem for blasting operations. Backbreak will interfere with the proper drilling and execution of the subsequent shot and can produce well defined boulders, which will not be broken by the subsequent shot. In order to determine the effect of timing on backbreak, a full scale blast with 6 1/2 inch boreholes was used to test the effects of timing. The test site was a quarry which had suffered from severe backbreak regardless of the blasting pattern or explosive used. One half of the production blast was loaded and initiated using the current technology at the quarry, the other half of the blast was deliberately timed in such a manner as to minimize backbreak. The timing was such to allow for ground movement in one row before the subsequent row fired. The test results proved that the amount of backbreak and flyrock could definitely be controlled with the selection of the proper borehole timing.

Jan 1, 1987

By D Vrkljan, Z Ester

There was no use of emulsion explosive at Croatia till 1997. Several attempts have been done to bear out the economical and technological affordability of applying the emulsion explosive for open pits and to make the contractor familiar with characteristics of emulsion explosive exepiting experimental blasts series at more open pits on different kinds of rocks. Testing the efficiencies of emulsion explosive there has been applied the original method for linear enlargement of burden of Sc.D. Josip Krsnik’s from Mining, Geology & Oil Faculty, University at Zagreb. The method of linear burden’s enlargement, in distinction from other methods concerning these problems, has been carried out in situ, under real exploitation conditions whereas the physical-mechanical rock’s features, geological conditions, bed relations and rocks’ structure influence the blast efficiencies. On such way, by mean of method the precise boring and blast sizes will be reached for each kind of rock and geological structural bed’s conditions referring to specific explosive type. The technical-economical analysis indicates the most favorable explosive type for specific bed.

Jan 1, 1999

By Daniel Castelo, Ben Potter

This paper will discuss the most efficient and effective way to use shape charges when considering standoff distances and the amount of an explosive to be used. For each shape charge test that was performed, a one inch diameter copper liner of 90o was used. Different standoffs for each shape charge were tested to see which one would penetrate the deepest into rolled homogenous armor steel (RHC 44). It was determined that a standoff of three cone diameters provides the deepest penetration. In addition to testing for optimal standoff distances, the effects of overfilling as well as under filling a shape charge with explosive was tested against a shape charge with the bare minimum amount of explosive for correct detonation. These “fill” tests were all performed at a standoff of three cone diameters. Overfilling has little to no effect towards penetrating deeper into a target while under filling a shape charge has an effect of shorter penetration. C-4 explosive was the main explosive for all shape charges.

Jan 1, 2011

By Goran Cirkovic, Zvonimir Ester, Josip Krsnik

During the reconstruction of the motorway Zagreb-Krapina three reinforced concrete bridges were demolished, for their width was not adequate for the new motorway. Demolition of the three bridges was carried out by blasting as duration of the traffic cut on the motorway and the railway was limited to maximally 4 hours. During that period of time the demolished bridges had to be removed. Therefore, very tiny granulation was requested suitable for loading and not endangering the surrounding structures. Before each of three main blasting, trial blasting were carried out including the seismic measurements registering the seismic effects. The nearest residential building was at the distance of less than 30 m from the place of blasting. Additional difficulty was the fact that by each of the three bridges there is a new bridge, with minimal distance between the old and the new bridge being 30 cm. As each of the bridges is of different construction and of various thickness, particular blasting technique has been prepared for each one of the bridges.

Jan 1, 1997

By Bill Paysse, Lyle Ruffle

My intention is to produce a video, pictorial, and oral presentation on utility blasting, primarily power pole holes and ditches. Included will be blasting for a take-off structure inside of Wanapum substation, jointly owned by BPA, PSE, and Seattle City Light, and blasting for 230kV steel tower foundations.

Jan 1, 2007

By Romel Villanueva, Juan Vasquez

We present the results of our field research on the variation of the density of the gassed explosives and their influence on the blasting results in the Peruvian mines: Yanacocha, Toquepala and Antamina. Currently, 90% of Peruvian mines uses gassed explosives, for their economic and technical benefits. But new practices and design criteria have had to be adopted, and the most important a careful control of the in-hole density, whose variation in the depth of the hole strongly affects the detonation process. For gassed explosives the density varies gradually according to the depth in the hole, due to the pressure on the bubbles by its own weight. The density at the bottom of the hole can reach critical values, which directly affects the start of the detonation in the booster zone with a high probability of nitrous fumes formation. On the other hand, density translates into the amount of explosive and energy available. Therefore, for the optimum performance of the explosive, the minimum and maximum values of the in-hole density must be determined. For the cases studied, the maximum in-hole density and the maximum charge length have been determined. When the charge length is greater than 7.0 m [ 23 ft.] special care must be taken with the cup density, which as a general rule should not exceed the value of 1.15 g/cm3 [71.8 lb/ft3] at the risk of losing the sensitivity at the bottom, also increasing the probability of nitrous fumes, bad fragmentation and finding intact explosive after blasting. In the large holes in Toquepala and Antamina mines, where the charge length can be greater than 9.0 m [29.53 ft]. If the cup density is greater than 1.15 g/cm3 [71.8 lb/ft3] the in-hole density can easily reach a high value of 1.30 g/cm3 [81.16 lb/ft3].

By Lawrence Mirabelli, William Hissem, Gary Veltrop

Capital Quarries Company, Inc., Jefferson City MO produces aggregate products for road base, asphalt, concrete and concrete block. With their production quantities small in comparison to those produced by the goliaths of the aggregate industry, they find it necessary to constantly stay on the leading edge of best practices for cost control, process and production improvement to sustain a successful business. In the words of Eric Strope, President, “The safety of our employees is foremost. They all work hard each day. They are focused on keeping our cost to manufacture down. As I see it, we cannot work any harder so we must work smarter!”

Jan 1, 2009

By P. D. Lightfoot, C. Badeen, R. Turcotte, D. E. C. Jones

Following localized (i.e. hot-spot) ignition, there is a minimum pressure required for combustion to propagate in water-based commercial explosives. The latter is usually referred to as the ‘Minimum Burning Pressure’ (MBP) of the explosive. In the present work, both an apparatus based on hot-wire ignition and an associated methodology were developed to measure the MBP of water-based explosives. It was demonstrated that the MBP constitutes a sharp pressure threshold below which the probability of inducing sustained burning in these explosives becomes very small. It was found that each emulsion explosive tested has a distinct MBP value, which depends critically on its formulation. It appears that this test may offer a firm basis for the classification of emulsion explosives for regulatory purposes.

Jan 1, 2004

By C H. Ryu

This paper presents a simplified two-dimensional numerical model of block fragmentation in a Jointed rock mass during the late or throw stage of a blast after wave effects have subsided. The model is based on the distinct element method. Examples illustrate the approach and allow for a comparison of effects of Joint patterns on fragmentation and resulting block motion.

Jan 1, 1986

By Frank Lucca

This paper includes research and investigation into blast design and blast optimization for vibration control in municipal and tight blasting situations, where specifications were extremely stringent. The paper is written for the field blaster to understand and develop blast plans based on field conditions. The paper includes blast design considerations, utilizing seismograph arrays to check and predict vibration results, and problems encountered in vibration monitoring in extremely tight situations (0-20 feet). Blast vibration frequency, acceleration, peak particle velocities, and relative displacement are discussed with effects in the near and far fields and blast designs utilized to stay under limits. The paper also discusses using the latest in technology for blast design to control vibration. Equipment includes 2D and 3D laser profiling systems, digital video, fragmentation analysis, seismograph arrays, and borehole tracking devices. Other topics are discussed such as public relations, working with regulatory personnel, unions, and other project consultants, and the problems associated with municipal blasting situations, such as, flyrock and proximity of other personnel and equipment on the project.

Jan 1, 2004

By Ruilin Lang

This paper presents an application of 3-D plots and non-linear regressions to define a sitespecific form of the charge weight scaled distance. The PPV (PPA) of single hole blasts is normally considered as a function of two independent variables - the charge weight and the distance. It is of great importance to obtain the relationship of the function accurately for a concerned site in terms of blast vibration analysis and modeling. However, in pre-computer time it was difficult to plot 3-D graphs. Consequently, a charge weight scaled distance was used to plot the PPV (or PPA) against the scaled distance as 2-D graphs. Blast vibration investigators use several forms of the charge weight scaled distances to plot data. We can exemplify them with the cube root of charge weight scaled distance, the square root of charge weight scaled distance, and other forms (Hossaini and Sen, 2004). Each of these scaled distances assumes relative contributions of the charge weight and the distance to the vibration attenuation. For example, the charge weight is assumed to have a less contribution to vibration in the cube root scaled distance than it is assumed in the square-root scaled distance. In reality, for different sites the relative contribution of the charge weight and the distance may be different and site-specific. This may explain that in some cases, the blast vibration data plots using these charge weight scaled distances are scattered. This could be largely due to the fact that the definition of the form of the charge weight scaled distance is not adequate for the particular site condition.

Jan 1, 2006

By Paul Worsey

A strong inverse relationship between rock face movement and stemming ejection is presented. Previously unpublished data from blast control plug research and development involving high speed video analysis, which was conducted between 1986 and 1988, is presented. Face and stemming ejection velocities were calculated for tests utilizing the same bench blasting configuration comprising; a 4 ft high bench in dolomite, 3 ft burden and single 1.75 in. holes loaded with 2 ft of small diameter cartridge emulsion. The singular difference between these tests was the stemming configuration. Varying lengths of stemming were used with the presence or absence of differing experimental configurations of blast control plug. The effectiveness of this plug has been published previously.

Jan 1, 1990

By R L. Calhoun

A paper on High Pressure Air must start with the industry accepted definition of High Pressure Air and, for the reader who is unfamiliar with High Pressure Air systems, include basic information on which type of Drilling Rigs can benefit from the use of High Pressure Air. The operation of a modern Downhole Drill must also be reviewed.

Jan 1, 1976

By Roger L. Keller

This paper examines the aspects of differing types of blasting cuts in underground headings with consideration to the reduction of number of holes and costs. At least one comparison study is related where costs per advance meter were significantly improved. The technical aspect of the paper covers a study of the effects of various blasthole delay intervals on resulting crater volume, ground vibration, and fragmentation for six hole V-cuts.

Jan 1, 1989

By Richard Dooley

This paper is one sided because it presents the problem, but not the solution. The problem of blisters (bubbles) and occasional tears in caisson liners occurred when blasting and we have not found a conclusive cause nor a preventive solution. (For back ground information, consult Techniques of Precision Blasting in the Excavation of Drilled Piers, by George Mosteller at the Sixth Conference on Explosives & Blasting Technique in Tampa, Florida 1980).

Jan 1, 1983

By Bradley C. Paul

Similar rock formations exhibit great variability in resistance to fragmentation during crater blasting. This observation was made during an attempt to calibrate the Kuz-Ram blast fragmentation model for crater blast geometries used in a modified in situ mining method for copper. The KuzRam equation is used to predict the fragment size distribution from blasting and includes a term called the "rock factor" to account for the fragmentation characteristics of the material. A data base of field scale crater shots in oil shale was available to supplement more limited data on copper ores. First, the blast geometry terms of the Kuz-Ram formula were modified to fit field data with various crater blast geometries. Rock factors were chosen to center the predicted curve on the curve representing observed fragmentation. Next, five possible sources of variability in rock factor were investigated: the grade of the oil shale, the aspect ratio of the charge, the type of explosive, the charge depth, and the rock itself.

Jan 1, 1989

By Theodore A. Christensen

Besides the moral responsibility for ensuring worker safety, today's blasting contractor has a major financial incentive for establishing an effective safety program: on-the-job accidents have a direct impact on a very sensitive cost area - Workers Compensation. Within specific parameters, a good safety program can reduce WC costs by lowering the Experience Modification Rate.

Jan 1, 1993

By Geoff Baldwin, Alastair C. Torrance

The use of monitors to assess equipment performance is carried out on a routine basis in many industries. The benefits gained through process control in knowing exactly how the equipment is working far outweigh the initial capital costs of the monitor. In the mining industry several dragline monitors have been developed and installed on equipment through out the world, but to date none has been fully accepted by the industry. This paper describes the use of a sophisticated monitoring system which incorporates an onboard processor to assess both dragline and blast performance. The use of a radio telemetry link for data transfer has removed the need for manual data collection and transfer, leading to a more efficient and powerful system. Significant effort has been put into the development and verification of a dig index to allow blast performance to be objectively assessed.

Jan 1, 1990