Search Documents

By Cristian Rodriquez, Fernando Fernandez, Rodrigo Fuentealba, Tom BoBo, Maria Rocha, John Kemeny

This paper describes a case study that was conducted at a new mine in South America. This mine has significant geologic variations that will result in different distributions of hard and soft ore being mined at different periods of time over the mine life. A study was conducted to determine the optimum blast design that will meet the mill throughput requirement of 95,000 tonnes (104,720 tons) per day for the first 10 years of the mine life. As part of this study, field rock mass characterization and laboratory tests were conducted. This includes standard rock mechanics tests as well as rock breakage tests used in mill simulations. The geology of the ore body was broken up into four Geologic Units, and statistical variations in the properties were determined for each unit. Using this data along with the data on the occurrence of the different geologic units over time, simulations were made of the run-of-mine (ROM) fragmentation due to different blast designs, and these results were used in simulating the resulting throughput after crushing and grinding. Four blast designs were considered with powder factors of 0.44, 0.54, 0.64 and 0.94 kg/t. The results of this study show that determining the proper blast design is important in ensuring that the mill throughput requirement will be met over the mine life.

Jan 1, 2015

By Khiva Haidar Shauma Tassno, Zulham Ahmad, Farhan Harist Maharesi, Abdullah Badawi Batubara

Blasting operations can use a bulk emulsion explosive (EE) with a formulation based on used oil as a replacement for refined fuel oil. The most commonly employed used oil for making EE is a mineral based used engine oil that passes an impurity content standard. It is known that not all types of used oil are easily incorporated into EE formulations. Impurities in used oil can disturb EE stability resulting in crystallization and phase separation and consequently led to poor detonation quality. In 2024, a poor blast result occurred at an Indonesian mine due to utilization of used oil that was not within specification. A research project conducted from February to April 2025 found that used transmission oil differs from used engine oil in hydrocarbon composition. Transmission oil contains more additives that affect EE stability due to polarity differences and the disruption of colloidal state stability. Lab tests including stress testing and crystal growth observation aided the development of a stable EE formulation based on used oil and used transmission oil. In mid-April 2025, blast evaluations were conducted using the EE that was formulated using used engine oil and used transmission oil. Measurements of velocity of detonation, fragmentation, and digging time, demonstrated high quality EE was produced. Application of used oil in EE revolutionized the capability of mining operations to improve blast sustainability and cleanliness. Through comprehensive research, robust testing, and effective supply chain management, it is possible to replace some portion of refined fuel oil with used oil without compromising blasting performance. The inclusion of used transmission oil broadens the overall used oil specification and increases the volume of recycled used oil available for blasting. The increased volume of used oil available can reduce the amount of waste generated by mining projects while maintaining operational efficiency.

Jan 26, 2026

By Jose Pineda, Abraham Lindo

The Panama Metro System’s Network expansion involves excavating a launching shaft for a tunnel boring machine (TBM) to traverse beneath the Panama Canal. The blasting needed for this shaft construction poses significant challenges due to the presence of concrete walls encircling the excavation. These walls must remain intact throughout construction and the tunnel's future operation. This case study is focused on devising and implementing safe blasting techniques crucial for the shaft's construction, ensuring the preservation of surrounding concrete walls and project equipment. As the interest was potential damage to the concrete walls, an appropriate vibration threshold for this project was also required as an alternative to the traditional U.S. Bureau of Mining RI-8507 limit (USBM RI8507). Blast modeling software was employed to conduct a series of blasting simulations. Parameters like hole diameter, spacing, depth, explosive type, and initiation methods were varied to evaluate their potential effects on wall stability and damage risk. The simulations revealed that smaller diameter holes and reduced spacing between blast holes would effectively mitigate the risk of wall instability. Additionally, utilizing electronic delay detonators and carefully planning the blast hole detonation sequence proved critical in minimizing potential damage. Executing these blasts in the field presented unique challenges, including strict charge per delay thresholds and logistical constraints. Consequently, continuous adjustments to blasting parameters were made and comparative result analysis. Beyond providing a safe blasting strategy for the TBM launching shaft, this study offers invaluable insights into adapting blasting designs to align with environmental and structural safety standards. These findings hold great potential to shape guidelines for analogous sensitive construction projects. They underscore the importance of leveraging prior research as a reference point, engaging with project designers and local authorities, and continually conducting testing and adjustments to ensure project success.

Jan 21, 2025

By Denard Brandt, Isidro Martinez, Greg Baker, Laura Slattery, Teddy French

The Dos Pobres Mine is a copper oxide heap-leach mine located near Safford, Arizona. Mine production is 180,000 tons (163,293 tonnes) per day with a stripping ratio of 2:1. During the startup phase of the mine, the required fragmentation size was easy to achieve as the ore was highly weathered and fractured near the surface. As the mine depth increased, the proper fragmentation size became harder to achieve due to less weathering and different rock types. Because copper recovery increases as crusher product size decreases, achieving the appropriate product size at the crusher is the operating priority.

Jan 1, 2010

By Earl C. Hutchison, Wade C. Hutchison

To effectively evaluate property damage that is claimed to have been caused by blasting activities and in order to lay the proper foundation to build the best legal defense, identification of the actual causation for the damages are necessary. For the past twenty years, engineering personnel from VCE, Inc. (previously Vibration Control Engineering, Inc.) have been evaluating claimed blasting damages with pre and post blast inspections, with analysis of seismic levels, blasting amounts at given distances, and with other engineering considerations. In addition to these evaluations, they have also documented other causes for damages which are of the types that are often claimed as blasting damage.

Jan 1, 1995

By Vasile Pop, Ovidiu Galca, Constantin Salajan

The paper comprises a brief presentation of the rock fracturing techniques applied in CNMPN “REMIN” Company’s mines in Baia Mare. Parallel are emphasized some shortcomings of this field. The second part of the paper includes our preoccupations and achievements, of the last period, in especially those linked to techno-economical indices improvement resulting from the development of relatively large section mining works and blasting applied with sublevel caving methods.

Jan 1, 2003

By Dipankar Gorain, A K. Vishwakarma, Vivek K. Himanshu, Murari P. Roy, Shubham Singh, R S. Yadav

The industrial establishments of a power plant consist of many important structures viz. cooling tower, wagon tippler, track hopper, plants and offices. The leveled foundation is the utmost need for erecting these structures. The leveling of the foundation is done by rock excavation, when the establishments have to be setup in hilly/rocky areas. Drilling and blasting is the cheapest and most dominant method of rock excavation. However, this method has associated hazards in terms of blast induced ground vibration, air overpressure, flyrocks etc. The foundation work and erection of the industrial buildings are done in parallel to achieve the faster construction of the establishment. The challenges to reduce the induced hazards in such cases are more. This paper presents a case study on the controlled blasting method devised for the rock excavation for construction of 2 × 660 MW Obra-C thermal power plant. The foundation work for this power plant was made by excavation of Dolomitic rock. The excavation work was performed in the proximity of the existing residence of the local people and Obra market. With the advancement of project, the excavation was also performed in the proximity to the ongoing construction work of various industrial buildings. Accordingly, the controlled blasting pattern was devised suitable to the specific sites. The pattern consisted of variations in blasthole diameter, burden-spacing, maximum explosive charge per delay, total explosive in a blasting round, initiation system and direction of initiation. The suitable muffling arrangements were also used, when the blast was conducted in the close proximity to the structures. The initial blasting pattern was established by analysis of blast vibration wave propagation characteristics. Thereafter, the final pattern was adopted for the safe excavation at the site. The safe excavation for the foundation work of this power plant has been completed successfully based on the devised controlled blasting pattern.

Feb 6, 2023

By John Cory, Ran Tamir

Blasting data analytics are being increasing used to increase mining productivity, reduce mining costs, maximize high margin aggregate products, and to reduce fines. Three examples will be illustrated using simple models to maximize the percentage of blasted rock within established dimensions and reduce fines-one from video fragmentation distribution information, the second from sieved crusher fragmentation data, and the third from plant production data. In addition, the use of sieved crusher results to determine blasting related fines and the use of mine productivity data to maximize aggregate sizes when pattern (burden and spacing) areas are changed will be illustrated

Jan 1, 2012

By M. Ganster

Austria’s biggest supplier of oil and gas, transports gas through the West Austria Gasline for domestic consumption. In addition, the OMV also works as gas carrier and ensures the transit into neighbouring countries.

Jan 1, 2010

By Mats Keisu, Bengt Niklasson

The Sofia project has increased the level of knowledge and technique within tunnelling, drifting and contour blasting.

Jan 1, 1992

By Zhou Jiahan Wang Feng

This paper introduces the mechanism and the operating process of dike building by silt squeezing blasting. DBSSB (dike building by silt squeezing blasting) has the following advantages: shorter construction period (the construction period is decided only by the speed of rock materials filling)greater consolidation of the body of the dike, more structural stability, smaller settlement. Therefore by conventional standards the same dike can be designed with a smaller cross section than other construction methods, and at a reduced cost when enough rock materials can be provided in site.

Jan 1, 2006

By Norman Paley

A blasting project was undertaken at the Teck Alaska Red Dog Mine to determine the extent that Semi-Autogenous Grinding (SAG) mill throughput could be increased by using electronic detonators. The Julius Kruttschnitt Mineral Research Centre (JKMRC) blast fragmentation, jaw crusher, and SAG mill breakage models were used to relate changes in the blast fragmentation measured with the SPLIT image analysis system to the SAG mill performance. For optimum performance a SAG mill requires a particular size distribution; a number of large rocks to facilitate breakage by impact, as few as possible middle size rocks that become critical size, and the maximum fines which will pass quickly through an open-circuit mill. Physical constraints of drill and charging equipment size limit the extent that pattern geometry can be changed, and the powder factor increased, to maximize fines. However, a growing number of studies have shown that the use of electronic detonators can lead to increased fragmentation and greater muckpile uniformity, providing an alternate means of increasing primary breakage by blasting. Unfortunately results in the literature rarely quantified the changes to the fragmentation distribution. The measured gyratory crusher fragmentation of 2,750,000t of ore was used to compare stockpiles constructed from shots using pyrotechnic detonators to those using Orica i-kon electronic detonators. In the first stage of the study, stockpiles shot using 25 ms inter-hole timing with pyrotechnic detonators were compared to stockpiles shot using the same inter-hole timing with electronic detonators. In the second stage of the study, stockpiles shot using 17 ms inter-hole timing with pyrotechnic detonators were compared to stockpiles shot using 8 ms inter-hole timing with electronic detonators. When electronic detonators were used with the inter-hole timing kept constant, fragmentation uniformity was slightly increased, but mean fragment size increased by 20%. When electronic detonators were used with faster inter-hole timing, fragmentation uniformity was slightly reduced, but mean fragment size decreased by 30%. Modeling was used to determine the SAG mill throughput which could be expected from this change in fragmentation to determine the pairs of pyrotechnic and electronic blast pattern geometries that would provide similar throughput. The economic benefit from the electronic detonator shots was calculated to assist in determining the optimum blast designs for their use.

Jan 1, 2010

By M. Gonçalves Peixoto da Silva, E. Rodrigo Carvalho Souza Siqueira

Mining in narrow veins is commonly applied for precious metals, generally carried out to extract gold in underground mines, due to the ore occurrence on narrow veins, mainly up to 2-meter large. The current work presents the implementation of the methodology in a zinc mine located in the state of Minas Gerais in Brazil. The Vazante Mine through the years has always carried out mining on stopes with a thickness larger than 3,5 meters, but nowadays due to the need to reduce the waste planned in its blocks, as well as increase the useful life of mine, mining has been implemented in blocks that are less than two meters. Given this, the challenge is to be able to carry out blasts that does not exceed the operational dilution required and does not generate an impact on recovery, as working with extremely heterogeneous stopes. This study seeks to correlate the main characteristics of stopes and its relationship with the results obtained in the execution of those blasts. Also, it proposes an analysis between the empirical data, and existing theoretical references, creating ideal mining parameters, such as minimum thickness, maximum height, and optimum timing in the blast plan. One of the main challenges for carrying out this mining method is the control of operational dilution, generally pointed out as the biggest difficulty for companies that adopt this methodology, due to the thickness of those stopes, any displacement can make it unfeasible, thus the technical level on carrying out the drilling and loading of these blocks must be impeccable, an understanding of the structural geology of the site is also essential for dilution control. The outcome will be a set of ideal parameters and mining methodology to guarantee the success in execution of these blocks, thus bringing a financial benefit to the company.

Jan 21, 2025

By Tom McDonald, Rodney Burke

As mining progresses in the West, the depth of material has increased, making highwall stability a major factor in safety and production. The Jim Bridger Coal Mine has made highwall stability a priority, concentrating on safety as well as increasing and improving production. Overburden depths are increasing dramatically; the geological environment consists of medium to soft material, faulting, water, and current pit alignment not favorable to joint planes. Angle drilling the presplit at 20 degrees became necessary as vertical presplit drilling produced wall failures.

Jan 1, 1997

By Shannon Studden, Angela King, Allan Koski

Cliffs Natural Resources is an international mining and natural resources company with over 160 years of history. A member of the S&P 500 Index, the company is a major global iron ore producer and a significant producer of metallurgical coal. Throughout its history, employees have been the foundation of the company’s success, which has long embraced a focus on continuous business improvement.

Jan 1, 2014

By Robert B. Hopler

The hazards which naturally prevail in underground coal mines, always severe and unpredictable due to the loosely-consolidated strata in which coal is frequently found, are increased by the commonly-occurring combination of coal dust, methane, and explosives. It was recognized by the mid-nineteenth century that coal dust was the basic factor contributing to disastrous explosions killing hundreds of miners, and that the ignition of methane gas was often the source of the coal dust explosions. It was apparent that preventing the ignition of methane was a critical part of avoiding these disasters, and it was also apparent that one cause of such ignitions was the firing of explosives. In addition, it was found that dust explosions were often initiated by blown-out shots of explosives in the absence of methane.

Jan 1, 1996

By Robert B. Hopler

Explosives have been important to the oil and gas industries since the very earliest days. The first wells of Pennsylvania and New York in the 1860’s were able to be brought back to productivity by the use of nitroglycerin after their porosity was lowered by the high para& content of their oil. Success in the use of seismic waves to locate enemy artillery in the First World War led to the use of explosives in the 1920’s for generating ground vibrations to locate geological structures favorable for the entrapment of oil. Explosives also find widespread use in the more conventional applications of well site preparation and pipeline construction. Explosives applications unique to the oil and gas industries include the jet perforating of casings and formations, fighting well fires, and cutting casing during well shut-in.

Jan 1, 1998

By Gerald R. Coonan

I'm really here to talk about my pet subject of government relations. I've been in Peabody's Environmental Quality Department, working on regulations, for over five years, and I have seen a number of individuals in the coal industry who were completely stunned when a new regulation was brought to their attention. Their first reaction was, "where did this come from"?

Jan 1, 1980

By Luana Ferreira de Carvalho, Aurelio Manço Garcia, Gustavo Sampaio Lopes, Jose Silvio Corsini, Davi Bastos Martins de Oliveira

The Enaex Mining Technical Solutions (EMTS) team, in partnership with the Anglo American Iron Ore Brazil drilling and blasting team, has developed a study aiming to optimize the blast design applied at the Minas-Rio project. The study consists of modeling the dynamic behavior of one lithological domain to determine the best configuration of drilling pattern, charge configuration, timing and sequencing of the blast designs applied at the mine in this particular rock. The first stage of the study was the recognition of the rock blast process in question, assessing key parameters that characterize this whole operation: geomechanical characteristics of the rock mass, implementation quality for drilling pattern and explosives charging (collar position, hole depth, explosive charge length and stemming size) and recognition of current blast designs. The central element of this study was the creation of a vibration attenuation and seed wave model which has allowed the characterization of this particular rock mass present in a region determined by the Minas-Rio team. The model is based on a near field vibration test, constituting a powerful tool in the design of blast parameters. The blast design developed from the damage model simulations basically modified the timing and sequencing. The aim of this study was to improve the fragmentation resulted by the blasting, considering the particle size requirements demanded by the primary crusher and to increase the productivity of the loading and hauling operations. The results were analyzed considering the effective productivity of the two different fleet types of shovels, where the authors have analyzed more than 46000 values of productivity from September 2017 to August 2018, taken from the Dispatch system. A significant increase in effective productivity of these load equipment was observed, 7% to the PC4000 fleet and 2% to the PC5500 fleet, values supported by statistical parameters and hypothesis tests.

By Daniel Vargas Quispe, Yorhinio León Robles, Marco Jauregui Vargas, Helen Espinoza Bailon, Oshin Quispe Luya

This project describes the methodology applied during the execution of tests to determine the multiple controls that mitigate damage to the final walls of the pit. The different tests were executed on production pattern, which considered: modification of the angle of pre-split drill line, damage evaluation in individual drills with different load designs, varied detonation sequences, capture and analysis of elementary waves. After the evaluation and analysis of the results obtained in the tests, we are in process to standardize various damage controls such as; the combination of pre-split drill line angles at 80° and 90°; charge design in buffer drills that reduce the angle of action of the explosive and a detonation sequence that involves the creation of a relief filter that is made up of the detonation of two rows next to the pre-split drill line, which will have the function of filtering the waves of vibrations produced by the detonation of the production drills and at the same time it modifies the direction of damage towards the blasted material. The analysis of the different controls, as well as their combination, will allow us to improve the compliance results of the formation of benches.

Jan 21, 2025