Search Documents

By Jack Eloranta

This paper documents the relationship between material handling and processing costs compared to blasting cost. The old adage, "The cheapest crushing is done in the pit", appears accurate in this case study. Comparison of the accumulated cost of: powder, selected wear materials and electricity; indicate a strong, inverse correlation with powder factor (lbs powder/long ton of rock). In this case, the increased powder cost is more than offset by electrical savings alone.

Jan 1, 1995

By D. Scott Scovira, Rick Webber

The Iron Ore Company of Canada [IOC] is a global leader in Arctic mining applications, and the blasting crew have something to be very proud of. On Wednesday 21 Dec 2005 at 3:28 PM the largest single bench blast in the company history was detonated. The successful firing of this 5.0 million tonne [5.5 million ton] blast surpassed the previous company record of 3.8 million tonnes [4.18 million ton].

Jan 1, 2008

By Pedro C. Carneiro, Luiz G. I. Maciel

"This article presents data of advance and excavation rates in tunnelling works, and how theseactivities interact with the duration and cost of a contract. These key parameters, after analysis andsynthesis, will be used in coming works to ensure the evolution and adaptation of the method created by the Norwegian University of Science and Technology - the NTNU Method - to Brazilianconditions, which will be reflected in the duration and cost of underground drill and blast tunnellingworks."

Jan 1, 2016

By Doug Wathen, Philip M. E Thomas

The City of Fort Myers needed to replace a 40-year old 42-inch storm sewer line in downtown Fort Myers with a new 54-inch line to accommodate population growth. The old line had to be kept operational while a new line was installed. the contractor spent two months using a drop ball, a hoe ram, and large rippers trying to break the three to four feet of rock that needed to be removed to accommodate the new pipe. Mechanical trenching was considered but was proven to be overly expensive. On very short notice, Ireco of Florida was asked to design and execute a blasting procedure that would allow this project to proceed. Nearby buildings were over 80 years old, three of them containing antique shops specializing in glass antiquities with attorney offices above them. High water table compounded problems with a 20-year old steel water main and clay drainage pipe 15 feet from the new sewer line. Holes had to be drilled within six inches of the edge of the existing pipe to four feet below the pipe on either side of the pipe and blasted. No interruption in the sewer line flow was to be tolerated.

Jan 1, 1996

By Doug Wathen, Philip M. E Thomas

The City of Fort Myers needed to replace a 40-year old 42-inch storm sewer line in downtown Fort Myers with a new 54-inch line to accommodate population growth. The old line had to be kept operational while a new line was installed. The contractor spent two months using a drop ball, a hoe ram, and large rippers trying to break the three to four feet of rock that needed to be removed to accmmodate the new pipe. Mechanical trenching was considered but was proven to be overly expensive. On very short notice, Ireco of Florida was asked to design and execute a blasting procedure that would allow this project to proceed. Nearby buildings were over 80 years old, three of them containing antique shops specializing in glass antiquities with attorney offices above them. High water table compounded problem with a 20-year old steel water main and clay drainage pipe 15 feet frcan the new sewer line. Holes had to be drilled within six inches of the edge of the existing pipe to four feet below the pipe on either side of the pipe and blasted. No interruption in the sewer line flow was to be tolerated.

Jan 1, 1996

By R C. Sittig

The manufacture of commerical detonating cord by the "wet process" technique is discussed. Raw material variability as a potential source of production problems is examined. Comparison to the "dry process" method is made. Inert samples, illustrating the cord's construction at various points in the production process, were distributed.

Jan 1, 1976

By Rahim G. Haghighi, Calvin J. Konya

Fragmentation is the fundamental concern of rock blasting and it measures the effectiveness of blasting. Fragmentation is sensitive to not only the interrelationship among the design variables, but also is sensitive to local geology. Local geologic conditions have a significant impact on the success of a blasting operation.

Jan 1, 1986

By Zhang Shixun, Wang Xuguang, Wang Guoli

A massive millisecond blast at an open-pit mine of large scale can be realized by using the blasting technology of pre-loaded explosives, which can enlarge production scale, reduce the frequency of blasting and of large production equipment movement, and raise the production efficiency. The reason why application of this technology is restricted at high sulfide ore deposits of variable and complex geological conditions is that an exothermic reaction will take place when explosives contact sulfide ores, which could lead to accidents such as spontaneous burning and detonation of explosives pre-loaded in boreholes, influencing blasting and production safety. The thermal decomposition reactions of emulsion explosives of different prescriptions in contact with pyrite have been studied by differential thermal analysis (DTA), kinetics parameters calculation and accelerating rate calorimetry (ARC), and on the basis of the above studies, the safety of emulsion explosives used in sulfide mines has been evaluated with the safe contact time of different emulsion explosives with pyrite determined.

Jan 1, 1998

There is an intuitive tendency to equate rock strength with rock stability, yet the two must be evaluated separately. A slope in strong hard rock is not necessarily stable, nor is a slope in weathered weak rock necessarily unstable. In some cases the reverse is true, depending on the geometry of joints and weak planes. The time element is a matter of special concern, that is how suddenly the failure begins and how rapidly it progresses. Sudden failures can be catastrophic, whereas creep usually is not. In soils and weathered rock, the process is usually incremental and is more likely to give some warning of impending failure. With careful observation, the failure process in these materials can be detected and monitored instrumentally or visually. In some cases, the slope may be stabilized, reinforced or modified. When that is not possible, there is usually enough time on this type of slope to remove men and equipment from the area before complete failure occurs.

Jan 1, 1996

By Jim Simpson, John Waller, Scott Stewart

The authors review the evolution of drilling and blasting procedures at this West Virginia surface coal mine where management seeks continually to improve and update the drilling and blasting programs. Today's operations require efficient programs which include quality control to maximize production and minimize the public's sensitivity to the blasting events.

Jan 1, 1992

By Carlos Agreda

The rock blasting environmental impacts such as: flyrock, groud vibrations,airblast,and/or noise, dust and fumes are identified and mentioned. Some comments on the correction factors that might be taken into consideration to calculate the initial velocity and the maximum projection of the rock fragments are mentioned as well.

Jan 1, 1995

By B Kniivila, A B. Andrews, T Lerick, Keith Jansen

Minntac Mine is a large, open pit taconite mine located at the center of the Mesabi Iron Range in northern Minnesota. The planned development of the Mine in the direction of nearby communities prompted a comprehensive study of off-site blast effects that resulted in numerous refinements in blasting practices.

Jan 1, 1984

By Richard L. Ash, Calvin J. Konya

Proper selection of the spacing distance between blastholes is fundamental to successful blasting. Its value directly affects the profitability of an operation. It also exercises control over adverse effects such as airblast, flyrock, generation of ground vibrations, and overbreak. One of the more significant factors influencing the spacing's specific value is the initiation firing time intervals used between blastholes. Examples are described to illustrate some of the problems that result when spacing and timing are not compatible.

Jan 1, 1979

By J R. Hearst, T R. Butkovich

Explosive-induced fracturing and permeability enhancement far from a free face were studied. A one-dimensional computer program, SOC, was used to predict the total failure-associated distortional strain, ef. Laboratory and field experiments associated the calculated ef with the observed fracture and permeability enhancement. An ef value of 0.015 corresponded to the observed radius of effect, which was about seven times the cavity radius and was consistent with predictions from SOC and from the literature.

Jan 1, 1976

By Dale Preece, Stephen Chung

Development of DMCBLAST-3D is continuing and now includes the capability to simulate the detonation of multiple blastholes in multiple rows that make up a conventional bench blast, either in a rock quarry or a surface coal mine. DMCBLAST-3D is a three-dimensional extension of the proven twodimensional rock blast modeling code, DMCBLAST. DMCBLAST has been under development since 1987 and has successfully predicted the physics, mechanisms and results of a number of different types of rock blasting including, coal mine bench blasting, mineral mine choke blasting and underground stope blasting. Substantial effort has gone into the qualification and verification of DMCBLAST by comparing computer code predictions with real blasts in the field. Comparison with field data has also provided significant guidance to the development of the code.

Jan 1, 2002

By Josh Campbell

Modern blast engineering involves the use of modern technology to provide more efficient blasts. Through the use of improved measurement techniques more information can be obtained on many of the physical variables of a quarry rock face. By employing this information, a more efficient production shot can be designed and loaded. Along with improvements in production, greater safety and improved environmental impact can be achieved. This paper concerns the employment of modern blast engineering at a granite quarry in the Southeastern United States. The test period extended over a period of approximately six months, and this paper will show the results achieved in that time span.

Jan 1, 1998

By Thomas L. Barkley, Michael A. Indihar

The new Cyprus Northshore Mining Co. has taken the previous blasting methods of Reserve Mining Co.'s mine in northern Minnesota and adapted them to a new competative Iron Ore Industry. Cyprus was challenged to develop new blasting methods to reduce costs and improve results over the previous mining operation. Many of the older procedures have been kept, but others have been changed in ways that bring the mine operation up to state of the art technology. In addition, unique ideas not previously tried in the North American Iron Ore Industry have been instituted. So far, this has reduced Cyprus's blasting costs by 70 percent.

Jan 1, 1991

By Terry Graf, Bill Thompson, John Guenther

SYNCRUDE CANADA LTD.. operates the largest synthetic crude oil production facility in the world. Over 60,000,000 Bank Cubic Metres of oil sand is mined each year from their open pit located in Fort McMurray, Alberta. Despite the extremely cold temperatures encountered during the winter months and the problems associated with frost buildup, SYNCRUDE has continued to operate on a 12 month per year basis. In 1989 SYNCRUDE mine management embarked on a comprehensive Frost Blasting program to improve mine production of their oil sand moving equipment. The following paper will discuss the development of their frost blasting program to its current status.

Jan 1, 1993

By Michael D. Duffy, Martin W. Chenoweth

"Tenn Luttrell Company (TLC) is a major lime and limestone producer in the eastTennessee area. The property, which isreferred to as the Chesney Mine, has been mined from the surface and underground overthe past 20 years. The ore body consists of three major zones of chemical grade limestonewhich lay at a dip of 30 _ 65 degrees. In July of 1989, Tenn Luttrell Company made thedecision to reopen the underground operations which had been suspended during a time ofincreased surface mining."

Jan 1, 1993

By Robert J. Nothnagle, Kristen Franz Begor, Rodney W. Sutch

Recovery of contaminated groundwater in a fractured bedrock system presents some unique problems. Typically, the most common problem occurs from the inability to adequately characterize the discrete fractures through which contaminants may be migrating. Without adequate characterization, difficulties arise in properly positioning recovery wells and verifying the performance of the system. To overcome these difficulties at a site in Upstate New York, an innovative approach was developed involving the creation of an artificial fracture zone through controlled blasting to intercept contaminated groundwater flow.

Jan 1, 1988