Search Documents

By Nan H. Lee, Christopher J. Hunter, Stephen H. Chung

Several factors affect the productivity of mining operations. The geological structure of a mineral deposit and the fragment size of blasted material are considered to be most influential. It is well known that productivity varies with mucking cycles and that this is related to the explosive energy produced by a blast.

Jan 1, 1991

By Yang Jun, Qu Mei, Zheng Yao-wu, Chi Li-yuan

Due to the necessity of the prediction of blasting seismic effect around strip mine bench blasting area, the paper provides a method to predict the blasting seismic effect by employing the superposition of seed waveform at different monitoring points. The method assumes that blasting vibration waveform per hole is similar to seed waveform at monitoring point. Therefore seismic wave consists of the superposition of the waves from all of blast holes. Firstly, via sensors multiple seed waveforms can be achieved at different distances from signature hole. Then, by using the given dose and the distance, the vibration waveform of a certain blast hole can be calculated by the corresponding seed waveforms. Finally, the initiation delay time interval per hole is added to the propagation time to the predicting point. The predictive waveform at the whole blasting area can be obtained by superimposing all of the single waveforms. Considering the vibration waveform of a single blast hole changes greatly with the distance, under different distances condition the seed wave employed to superimpose is achieved from the similar distance. The experiments demonstrate that based on the method the predictive vibration waveform and spectrum are basically consistent with monitoring results around near-field blast. Compared with single seed wave method, the superposition method of multiple seed wave is more reliable to predict the duration of blasting vibration, the peak particle velocity, dominant frequency and frequency distribution.

Jan 1, 2015

"Rock falls involving a relatively small amount of material are a leading cause ofinjuries in underground mines in the United States. A contributing factor is unwantedblast damage and over-break. A goal of the United States National Institute forOccupational Safety and Health is to reduce the number of ground fall-related accidents by improving drift driving practices through the introduction of perimeter control blast designs. This paper presents a blast design technique based on a hydrodynamic method. Using commonly available explosive and geometry data, the theoretical particle velocity is calculated as a function of distance away from a cylindrical charge. A calibration factor is introduced to account for actual conditions by comparing the predicted values to a set of field data. The calibrated curve can then be applied for design. The paper introduces modifications to account for different explosives from those used in a calibration test. The application of the approach is demonstrated with respect to a data set from a large-scale concrete block test."

Jan 1, 2009

By Panagiotis (Takis) Katsabanis, Lyall Workman, Jack Eloranta

The reduction of metallic ores to concentrate consumes a great deal of electrical energy. In the past two decades, a number of case studies have demonstrated a beneficial relationship between powder factor and grindability. However, changes in mill performance cannot be attributed to changes in feed size alone. Blasting energy and the distribution of that energy appears to affect subsequent comminution beyond crushing. This experience has prompted researchers to attempt to duplicate and quantify the mechanisms involved. To date, published reports indicate a measure of success. However, the blast engineer and the mill engineer still lack the tools and basic understanding necessary for full drill to mill optimization.

Jan 1, 2015

By Alain Blanchier, Pascal Bernasconi

Blasting operations took place on Channel coast NW of France to extend Flamanville Nuclear Power Plant (EPR new generation). The closest operating reactor building was monitored by a 24 remote vibrations transducers network to fulfil, on one hand, the severe environment constraints and satisfy high degree of productivity required by the project, on the other hand. Although these requirements usually are incompatible, this challenge compelled to introduce a seismic modelling technique to optimize blast designs using electronic initiating system. The “Hybrid Seismic Modelling” (MSH) uses blastholes signatures (seismic vibrations records) which are greatly dependent on geology and alteration of rock mass, explosives, charge geometry, blast configuration, and the final excavation shape. In order to respect severe vibrations limits, excavation layout was divided into areas with specific blasting modules - type and number of charges, single charge, initiating sequence. Thanks to this technique, it has been possible to reach lowest blasts vibrations levels and a better productivity compared to classical blasting operation at the same location in the past. After the modelling method presentation - principle and use precautions, technical improvements are reported.

Jan 1, 2008

By Catherine T. Aimone-Martin, Brent Meins

Blast vibration monitoring for buried pipelines is typically conducted at the ground surface with a shallowly buried geophone. In many jurisdictions across the U.S., blast-related vibration limits set for pipelines are dictated by surface measurements and do not consider the significant reduction of PPV amplitudes acting on the pipe at depth. This study involved a vertical array of geophones deployed in drilled holes at two blasting sites of the Loop 202 South Mountain Freeway construction project in Phoenix, Arizona. City of Phoenix pipeline engineers were concerned that blasting would damage an aged 48-inch (122 cm) prestressed concrete cylinder pipe (PCCP) that serviced water for South Phoenix

Jan 1, 2019

By James Goldberg, Sally Zadra, Wiliam Reisz

Early recognition and risk assessment is critical to sustaining a safe and productive blasting operation. While every blasting environment holds inherent risk, highwall blasting in highly congested areas such as Hanson Material Service Corporation’s Romeoville and Thornton quarries in the greater south Chicago metropolitan area can be particularly perilous

Jan 1, 2008

By Duane Skidmore, Calvin Konya

The supply crunch and cost rise for ammonium nitrate (AN) over the past year have been influenced by a number of factors. These include a general inflationary tendency, particularly great cost rises in fuel, and by a market condition in which demand for ammonium nitrate is great and supply is limited. Demand is largely confined to agricultural and explosives uses with explosives subdivided into mining, construction, and quarrying. The projections show that demand may be expected to increase markedly for the indefinite future in the agricultural and mining sectors of the ammonium nitrate market while fluctuating with indicators of economic activity for the construction and the quarrying sectors. Supply is projected to increase with plants being designed and built due to high need levels and commensurately high profit potential but not enough are planned to provide an equilibrium market. Constraints upon supply increases to match demand increases include shortages in the raw material, natural gas, high cost of investment capital, high equipment costs and long construction delays. The result should be, even under optimistic conditions, considerable shortage and resultant pressure for higher prices through 1979 for ammonium nitrate. The best hope for relief in the intervening years appears to be conservation. In blasting operations, the earliest and best proven route to conservation seems to be improved utilization available from application of highest available technology and most efficient current blasting practice.

Jan 1, 1975

By K B. Holm

This paper deals with the advances made at Syferfontein Colliery in the calculation and control of dragline methodology. The high capital outlay and operating cost of a dragline necessitates strict control of all aspects of the dragline operation. Before purchasing a dragline, a complete evaluation of all the parameters that can affect the viability, now and in the future, of the dragline operation needs to be completed. Such parameters as thickness of burden, material properties (swell), “castability”, pit width and pit length, etc. need to be considered.

Jan 1, 1994

By Brent Blanchard

Dallas/Fort Worth Airport recently took a major step in its fiveyear expansion project with the explosive demolition of the Hyatt Regency Hotel West. Built in 1965, the Hyatt Regency held the distinction of hosting five U.S. Presidents over the years and was reportedly one of the first hotels in the world to be built within an airport’s boundaries.

Jan 1, 2003

By Paul Worsey, Larry Frost, Braden Lusk, Seok Bin Lim

For certification of blast resistant windows, current tests consist of arena tests or large air gun tests. Arena tests involve the detonation of more than 1000 pounds of explosives with windows placed in the range of hundreds of feet. The result of an arena test is a loading on a window consistent with an expected industrial or terrorist blast. Due to the nature of this type of test, only a limited number of facilities are available and operational costs can be extremely high. Air gun tests involve the use of compressed air and a failing diaphragm fired through a large tube. Although this test is more cost effective and easier to administer with lower environmental impacts, it is not an explosive loading and does not create a negative phase on the tail of the pressure pulse. Simply using a small charge in close proximity to the window is not a viable option either. The pressure peak can be reached using this method, but the duration of the pressure pulse is such that the positive phase impulse is on the order of ten times less than that for an arena test.

Jan 1, 2006

By Italo Onederra, Miguel Araos

"Most of the current explosives for mining blasting activities are based on ammonium nitrate (ANFO, emulsions and watergels). AN-based explosives’ detonating properties were discovered in the 50’s and since then they have proven to be reliable, safe and cost effective. However, there is no current alternative raw material to replace AN. As part of a program of research initially funded by the Australian Coal Association Research Program (ACARP), Mining3 and the University of Queensland engaged in the search for potential oxidizing agent alternatives that could replace AN in the manufacture of mining explosives. Candidates included those that are produced in large quantities and that can be cost competitive with ammonium nitrate. The initial work identified hydrogen peroxide (HP), calcium ammonium nitrate (CAN) and sodium nitrate (SN). Explosives mixtures were prepared and sensitized using void sensitization techniques. The detonation properties results showed that explosives based onmixtures of HP/CN and HP/SN as the oxidizer were able to detonate in a range of 2000 – 5000 m/s, indiameters 50 and 102 mm, and densities in the range of 0.50 – 1.40 g/ml. Although more studies need to be conducted to fully understand these explosives, if successful, these explosives would be able to offer an alternative to the AN-based explosives in the mining industry."

Jan 1, 2017

By Brad H. A Brown, J Paul Tidman

To design a blast, one must give consideration to safety, economics, geometry, geology, production needs, and a variety of other requirements. To compare designs requires the time to develop alternatives, analyze, and then improve on them. A number of tools are available to assist with the first set of requirements, however they are poorly integrated. SHOTPlus is a program to improve the efficiency of blasting operations, by combining measurement and blast design tools, and offers the user the time and means to modify designs and explore alternatives.

Jan 1, 1997

By M Lemieux, R Mason

The SABREX blast modeling program was introduced to I.O.C.C.'s Carol Lake Iron Ore Project in December 1987. As part of CIL's Technical Services, SABREX was used to implement an optimization program designed to analyze and introduce various grades of MAGNAFRAC at a constant pattern while maintaining acceptable blast results.

Jan 1, 1989

By Wade A. Narin, James K. Mitchell

Hydroblasting is considered a distinct soil improvement technique from explosive compaction, though the blast designs for the two techniques are similar. Hydroblasting is a three step process developed for densifying unsaturated, collapsible soils, especially loess. The required steps are: prewetting the soil to an adequate saturation, placing and detonating the explosive charges, and consolidating the soil (squeezing the water out of the pore spaces between the soil particles under gravity) to a denser state.

Jan 1, 1995

By Robert A. Cortese, Lon D. Santis

This paper describes a method of measuring continuous detonation rates using standard electronic parts, coaxial cable, and a data recorder such as an oscilloscope. Three six-volt lantern batteries or a DC supply power the electronics that cost less than $100. Included are means of showing low battery power, finding the proper voltage scale on the recorder, and test triggering of the recorder. Modifications of the circuit allow for use in the field to measure charges up to 57 meters and for use in the laboratory to measure short charges. The high resistance (8.709 Ohms/meter) coaxial cable is a mass produced, special order cable available commercially. The driver circuit delivers a constant current to the cable, and as the detonation shorts the cable, a change in circuit voltage occurs. Recording this voltage change over time allows determination of detonation rate resolute to the sampling speed of the recorder. An oscilloscope or personal computer with a data acquisition card can easily record the data for analysis. Detonation rates recorded in the laboratory using the coaxial cable and the Bureau of Mines's traditional probes are presented. The system accurately measured the detonation rates of ANFO confined in steel pipe, detonating cord, and unconfined high explosive.

Jan 1, 1996

By J. Baird

The Sappington Bridge, a steel arch span bridge constructed in 1904 over the Meramec River, was demolished due to its advanced state of deterioration. The demolition was a project to benefit Crawford County, Missouri, the U.S. Army, the Missouri Department of Transportation, and the University of Missouri – Rolla (UMR) was conducted jointly by the UMR Rock Mechanics and Explosives Research Center (RMERC) and the UMR Center for Infrastructure Engineering Studies (CIES). By arrangement with Crawford County, a 55-foot span of the old bridge was brought to the University Structures Laboratory in Rolla, while the longer, 200-foot span of the bridge was demolished using preburning and explosives. Originally, the longer span was to be blown up by C Company of the 5th Engineer Battalion (from Ft. Leonard Wood, Missouri) under the supervision of personnel from UMR. Unfortunately, permission for the operation from the Department of the Army could not be obtained in time to meet permitting requirements for the demolition. Therefore, a commercial demolition contractor was employed to perform the demolition, and to remove the scrap.

Jan 1, 2003

By Randy Martin, Jessie Bonner, Peter Boyd, Mark Leidig, Timothy Rath

We conducted the Vermont Damage Experiment in central Vermont during July 2008. Five single-hole explosions with yields ranging from 60.8 kg (134 lbs) to 122.5 kg (270 lbs) were detonated in homogeneous, low fracture density granite. The goal of the experiment was to quantify the different levels of rock damage around the source and then relate the seismic wave generation to the degree and distribution of damage and fragmentation. In addition, explosives with different velocities of detonation (VOD), including black powder (0.53 km/sec; 1737 ft/sec), heavy ANFO (4.8 km/sec; 15734 ft/sec), and COMP B (8.1 km/sec; 26574 ft/sec) were detonated to relate the VOD to seismic wave generation and extent of damage zones in the source region. Over 120 seismic stations were deployed to record the explosions at distances between 5 m and 30 km (15 ft to 19 miles).

Jan 1, 2010

By Jan Mehren, Arild Neby

Underwater Tunnel Piercing or Lake Tap, often also called the Norwegian Method, will in many projects be an important part of the hydro electric development scheme. The very last blasting round in the Lake Dorothy Lake Tap Tunnel, which penetrated into the lake at a depth of 120 ft (36 m), was such a key step in constructing the Lake Dorothy Hydroelectric Project. A lake tap project is multidisciplinary. Besides the pure blasting and construction technique aspect, engineering geological and geometric considerations that aim to optimize the tunnel alignment making a lake tap possible at minimized risk are of significant importance. Output data from numerical model analysis of the hydrodynamics resulting from the blasting is vital for the final adjustments to the geometrical layout. The planning of monitoring systems for the surveillance of hydrodynamic impact on valves and pipes as well as control with water levels and air pressures prior to and during the blasting, are all additional crucial elements in the design. More than 600 lake taps have been successfully performed in Norway since the 1890`s. The technique, which deserves to be called well proven, has been applied mostly in the hydropower sector but over the last 20 years also for shore approaches in the oil and gas industry. The demand for this technique seems to be ever more growing.

Jan 1, 2009

By Thomas Hans Kleine

In general the software required by a blast designer includes tools that graphically present blast designs (surface & underground), can analyze a design or predict its result, and can assess blasting results. As computers develop and computer literacy continues to rise the development of and use of such tools will spread.

Jan 1, 1995