Search Documents

By Benjamín Cebrián, David Flores, María Rocha Gil

This document shows the evolution of drilling and blast digitization process, savings and trends in a mine, using new technologies that creates business opportunities and general improvement of D&B process.

Feb 1, 2020

By Peter Moser, Mark Ganster, Andreas Gaich

Surveying of a bench face before blasting is a pre-requisite for a proper blast planning and for a satisfying blasting result both in terms of safety and fragmentation. When surveying a bench face, preferably a large amount of measurement points are required in order to determine the geometry and especially the irregularities with sufficient accuracy. Only contact-free measuring systems allow evenly distributed measurements over the whole bench surface. Existing systems such as total station, laser profiler, or laser scanner show significant drawbacks such as that surveying results are just isolated values of the bench geometry such as heights or profiles, that borehole positions have to be defined in advance in order to know where to take profile measurements and that systems require special surveying skills and that they are expensive too. In order to overcome these difficulties and to provide the blasters a simple tool for bench surveying, blast design and layout and the subsequent back-transfer of the blast plan into the quarry, the Department of Mineral Resources& Petroleum Engineering of the University of Leoben, 3G Software & Measurement company and Mineral AB, one of the largest producers of aggregates in Europe formed a joint venture to develop a new system. Based on an existing stereophotogrammetric system for rock surface surveying and joint analysis (JointMetrix), a new tool was developed within a year. Apart from several mines and quarries using that new tool already today in the daily work, both the Department of Mineral Resources& Petroleum Engineering at the University of Leoben and Austin Powder GmbH Blasting Service did a lot of studies to determine the reliability of the new stereophotogrammetric blast surveying and planning system and its precision in comparison to classical laser surveying equipment. After 1 year of testing and comparison with laser based surveying instruments, it can be concluded, that the new technology of blast surveying& design systems based on stereophotogrammetry is suitable for being used in the daily work routine in quarries and mines. The comparison of the precision of laser based systems and stereophotogrammetric systems has shown, that the deviation between these two types of systems is less than 10 cm, in many cases even lower.

Jan 1, 2007

By Benjamin Cebrián, María Gil, David Flores

In many occasions during the Mining operation life, blasting engineers find different and controversial results of fragmentation, dilution or wall control for the same geotechnical domain and blast design (pattern and explosive charge). Most of the times, the difference between same blast designs is not measured, not controlled. Once a blast designed is defined, the most important part of the process after that is the implementation of every step of the blast on site. Almost nobody is measuring it, controlling it, but just controlling implementation is possible to relate blast design with results in a consistent way, to optimize the full process of D&B. Controlling implementation not only per event but also to check and change trends and decision-making is paramount for optimization and saving millions of extra costs every year. The lack of resources and the hardness to manage all the info created every day in a blast make this process very tough and difficult to maintain in long term. The use of new technologies on site and software that allows a best, more consistent and continuous control of blast implementation have been proved to be the key for optimizations and cost saving. This document shows the evolution of drilling and blast digitization process, savings and trends in a mine, using new technologies that creates business opportunities and general improvement of D&B process.

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson

"An Event Tree Analysis (ETA) is an established approach for logically deconstructing and assessing scenarios for probabilistic risk assessment. This deconstruction into a series of understandable eventsfacilitates probability estimation for explicitly defined explosive terrorism scenarios with consideration of modes of possible failure during execution (a scenario is defined through selection of a target, selection of an explosive material, and interdiction prior to arriving at general target location, etc.). Further, each event is decomposed into a range of possible outcomes. The physical action or reality ofthe outcome is statistically represented by “branches” of the event tree (e.g., the terrorist may choose totarget a stadium, hotel, or subway; terrorists may be successful or unsuccessful in acquiring the material)."

Jan 1, 2017

By L. L. Oriard

he Metropolitan Water District of Southern California (MWD) supplies water to some 16 million people in a semi-arid region. Most of this water is imported. Some of the supply lines cross over the San Andreas fault, one of the most notorious and active faults in the U.S. There was a serious need for emergency water in case normal supplies should be interrupted. To fill that need, MWD had to find a reservoir site on the west side of the San Andreas fault, west of the mountains. Because of the distinctive nature of the location, it was necessary to construct a huge “bath tub” by building a dam at each end of a valley, requiring some 115 million cubic yards (88 million cu.m) of fill. In effect, two large-scale surface mining operations have been under way simultaneously. The $2.2 billion project is known as the Eastside Reservoir Project. Because of space limitations, this paper will be limited to those topics which are expected to be of primary interest to explosives engineers, principally related to large-scale rock fill production. There is not sufficient space to discuss the many diverse geotechnical questions related to site selection, geological and geophysical field testing, laboratory testing and design considerations. This brief overview may assist those who might be interested in making a tour of the project site following the ISEE conference.

Jan 1, 2000

By Gungor Tuncer, Ali Kahriman, A. Kadir Karadogan, Savas Gorgun

The environmental problems arisen from ground vibration and air blast have been faced and discussed frequently in various industries such as mining, construction, quarry, pipe line etc. where blasting is unavoidable operation. Structural damage due to ground vibrations creates great socio-economic problems for mine and quarry management as well as for the people residing in its vicinity, therefore in bench blast design, not only the technical and economical aspects, such as block size, uniformity and cost, but also the elimination of environmental problems resulting from ground vibration and air blast should be taken into consideration. With the general trend towards larger blasts in mining and infrastructure excavation, ground vibration and air blast problems and complaints have significantly increased. With increasing environmental constraints on the levels of disturbance induced by blasting operations upon nearby residents, there is an increasing need to be able to design cautious blasting with greater precision, therefore determination of maximum amount of explosive per delay for a certain distance especially in large blasts is of great importance for the elimination of these environmental problems. In another word, prediction of ground vibration components is extremely important for the minimisation of the environmental complaints. Estimating of particle velocity and other components of ground vibration with reliable approaches will give important facilities to the blasters. Although many studies had been carried out to isolate environmental problems induced by blasting in the past, a general reliable formulae has not been established yet. Due to restrictions on the complexity of ground motion, blasting and test site factors, experimental studies are still necessary for each site to minimise environmental issues. This paper presents the results of ground vibration measurements carried out during the excavation activity for contruction of an organised industrial region located nearby Istanbul in Turkey. The major rock type is granite that is encountered at this site. Within the scope of this study, in order to predict peak particle velocity level and produce a site-specific propagation curve for this site, ground vibration components were measured for blast events during bench blast optimization studies over a long period. In blasting operations; ANFO (blasting agent), gelatine dynamite (priming) and delay detonators (firing) were used as explosives. While the parameters of scaled distance (charge quantity per delay and the distance between the shot and the station) were recorded carefully, the ground vibration components were measured by means of two different vibration monitors for every event. Then, the data pairs of scaled distance and particle velocity were analyzed. The equation of scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity. At the end of statical analysis and evaluations an empirical relationship with good correlation was established between peak particle velocity and scale distance for this site.

Jan 1, 2000

By Lon Santis, David Buckwalter, Ken Steinmetz

This paper describes a magazine security system using two readily available cellular telephone-based technologies. The system is comprised of vibration sensors and remote cameras. The system is used at a Bureau of Alcohol, Tobacco, Firearms, and Explosives (ATF) licensed explosives storage location in Pennsylvania to comply with PA Department of Environmental Protection (PADEP) regulations. The system provides instant notification to the licensee via cellular modems, text messaging, phone call, and e-mail. Likewise, the licensee can control the system remotely over the internet and using text messaging commands. The vibration sensors attach to the door of the metal type I magazines magnetically and detect any movement or vibration. The cameras trigger on movement and thermal radiation changes and can also be triggered manually to check alarms received from the vibration sensors. The previous system was comprised of a base unit and magnetic strips. The magnetic strips were powered by a hard line from the control unit and mounted on the doors and top of magazine creating a bond, that when broken triggered an alarm. Our main issues with the unit were the delay in alert times and tech support. Because of these issues, we decided an upgrade was necessary. Compared to that previous system used at this site, these new systems are highly affordable, carefree and reliable.

Jan 1, 2014

By Art Frye, Lee Pratt, Gaichang Zhao, Greg Newman

This paper will discuss the Wight Pit wall slash at the Mount Polley open-pit copper-gold mine that scavenged a high grade block of ore from two double-benches of the pit wall. The Wight Pit orebody, discovered in 2003, is located in the Northeast of the property with the southeast pit wall approximately 50m (165ft) from the edge of Polley Lake. In early 2009, the Wight Pit was nearing completion while an estimated 150,000 tonnes (165,000 tons) of ore averaging a grade of 1.4% copper remained just inside the southeast pit wall. The ore block started 24m (78ft) above the pit floor and extended up another 48m (157ft) with a 70o plane defining the back of the block.

Jan 1, 2011

By Jena Moshen

Underground Bulk Systems (UBS) technology has gained widespread application in tunneling and underground mining owing to its safety, reliability, increased Velocity of Detonation (VOD) and excellent results. However, its application in perimeter blasting is still limited and researchers are looking at ways of harnessing this technology for perimeter control. This simplifies the charging process by using one cost efficient product for charging both the perimeter and grid holes. This paper presents a case study on the application of underground bulk emulsion explosives for perimeter control blasting in underground room and pillar platinum mines. In order to achieve the required coupling ratios in the perimeter holes, the emulsion is loaded into specially formulated smaller diameter polyethylene (poly) pipes. The effectiveness of this method was evaluated using information obtained during routine blast audits and data supplied by the mines on half cast factors, over break and under break as well as analysis of data from Ground Penetrating Radar (GPR) Scans over a period of four years. This method of perimeter control, has given the platinum miners in Zimbabwe a competitive edge in cost effective perimeter charging and blasting by simplifying the previously costly deployment of traditional barrels and other decoupled cartridges. The method has been adopted by all the platinum mines in Zimbabwe as it has proven to be a cost effective alternative of controlling the perimeter walls, along with other key benefits that relate to safety, productivity and effectiveness.

Jan 1, 2018

By Jared Redyke

Thursday, October 14, 1999 marked another important milestone for America’s space program. At exactly 10:05 AM EST on a beautiful, sunny Florida morning, Dykon, Inc. of Tulsa, Oklahoma detonated approximately 300 pounds of explosives to fell the seven million pound Umbilical and Mobile Service Towers at Space Launch Complex 41 (SLC-41) at NASA’s Cape Canaveral Space Station. Completed in 1965 at the height of the Space Race to the moon, the Mobile Service Tower/Umbilical Towers (MST/UT) were part of the Titan rocket launch facilities. The MST was 265 feet high and weighed over five million pounds. The UT was 175 feet high and weighed over 2 million pounds.

Jan 1, 2001

By Marcia Harris, Richard Mainiero, Michael Sapko

Since 1988, there have been 17 documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through ground strata into occupied enclosed spaces as a result of proximate trench blasting or surface mine blasting. These incidents resulted in 39 suspected or medically verified carbon monoxide poisonings and one fatality. To better understand the factors contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out studies in a 12-foot diameter sphere to identify key factors that may enhance the levels of CO associated with the detonation of several commercial trenching explosives. The gaseous detonation products from emulsions, a watergel, and ANFO blasting agents as well as gelatin dynamite, TNT, and Pentolite boosters were measured in an argon atmosphere and compared with those for the same explosives detonated in air. Test variables included explosive formulation, wrapper, aluminum addition, oxygen balance, and density. Major contributing factors to CO production, under these laboratory test conditions, are presented. The main finding is the high CO production associated with the lack of afterburning in an oxygen poor atmosphere. Fumes measurements are compared with the manufacturer’s reported IME fume class and with the Federal Relative Toxicity Standard 30 CFR Part 15 in order to gain an understanding of the relative toxicity of some explosives used in trench blasting.

Jan 1, 2003

By Larry R. Fletcher, John W. Kopp

The safety record for explosives in U. S. mining is excellent considering that over 4 billion pounds of explosives are now being used each year. However, blasting accidents remain one of the most serious concerns based on the number of injuries, the injury severity rate and the disaster potential. The Bureau of Mines has been analyzing blasting accident data obtained from the Mine Health and Safety Administration (MSHA) to determine the most frequent causes of mine blasting accidents and to examine trends in blasting accidents. This accident analysis is an update of two previous blasting accident studies conducted by the Bureau and published in 1983 and 1987.

Jan 1, 1991

By Stephen Mansfield

In metalliferous mining operations, subdrill is that portion of the blast hole that is drilled below the target grade elevation, and in most cases loaded with explosives. Its primary aim is to enable efficient excavation down to the target floor level. Subdrill is often described as being expensive and that excessive subdrill should be avoided, as it can result in damage to the subsequent floor, lead to difficult drilling conditions and higher vibration levels. As a result, many operations aim to apply the bare minimum amount of subdrill in order to excavate to the target floor. At a large open cut copper operation, challenging geological structure resulted in slabby and blocky fragmentation in the stemming region, resulting in poor crusher throughput due to bridging. To overcome the poor fragmentation in the top of the bench, longer than conventional subdrill was used to precondition the top third of the bench. The technique significantly improved the run of mine fragmentation and resulted in feed to the in-pit crushers that is more consistent, which produced less crusher downtime due to bridging. A new method of quantifying the energy in a blast has been created. Termed the linear powder factor, or energy factor, the calculation considers the energy contributed by the subdrill of the upper bench and its impact on the energy in the lower bench. The technique enables blast designs to be optimised to deliver finer fragmentation and more consistent blast outcomes. To support the layer of preconditioned rock at the top of the bench, an innovative new device was developed. The device is inserted into the drill collar immediately after drilling and remains in position throughout the subsequent steps of hole depth measurement, priming, loading and removed prior to stemming. The device not only supports the broken rock at the top of the bench, but also minimises the amount of drill cuttings that fall back into the hole. Furthermore, the device helps protect the hole from damage by external factors such as weather events, drill tracks, vehicle tyres and movement around the collar during measurement and loading of the blast hole.

By F. Schott, M. James, G. May, E. Baker, C. Johnson, R. Bauer

Explosive demolition typically utilizes cutting charges to sever columns, detonating cord to time charges and provide an initiation path, and dynamite as a kicker charge. The kicker charges of dynamite are used to “move” columns out of alignment, causing collapse. Demolition projects involving dynamite can pose significant health and safety risks to workers and the public. Nitroglycerin in dynamite can cause dizziness, fainting, and other health problems. Moreover, dynamite placed directly on columns can result in fragmentation and cutoffs, preventing other charges from being initiated and resulting in incomplete demolition. Fragmentation can occur from columns and travel significant distances from the initiation point, sometimes reaching hundreds of meters away. This fragmentation can pose serious dangers to anyone in the vicinity, including workers and members of the public, as the debris can cause severe injuries and property damage. The force and velocity of the fragmented material can be unpredictable and difficult to control, making it important to take proper safety precautions and consider alternative demolition methods that minimize the risk of fragmentation. Previous work concluded that casing charges in water showed that a reduced dynamite charge mass could still successfully kick the charge out of alignment. This study aims to investigate the use of Pentolite boosters in water-cased charges as a safer alternative to dynamite-based demolition. The research involved testing various amounts of dynamite and pentolite boosters in water to compare their effectiveness in moving a hanging W-beam, which swung freely like a ballistic pendulum. Water-cased charges consistently move the column at a higher velocity than the traditional dynamite charge placed directly on the column. The method of water-casing increased the area of impact and impulse felt by the column, improving demolition efficiency when compared to traditional demolition methods as found in previous studies. Pentolite water-cased charges moved the column at 7.8 meters/second (m/s) while the dynamite water charge moved the column at 5.9 m/s. The increased strength and explosive properties of the pentolite contributed to this increase in velocity. This study showed that it is feasible to remove dynamite from demolition projects by utilizing pentolite boosters and that when considering safety, explosive properties, and effectiveness, pentolite boosters can be cost effective as well.

Jan 1, 2024

By A. Gontijo, A. Matos, P. Lincoln, L. Fonsecail

This paper investigates how to manage and model the vibrations caused by rock blasting in a Brazilian underground mine. Considering the frequent detonations and the previous lack of effective vibration control, understanding, and reducing the impact of these seismic waves is critical. We emphasize the use of the near field model technique, which considers the varied physical properties of different rocks, optimizes blasting plans, and minimizes damage to the rock mass. We detail a case study that demonstrates a comprehensive approach to vibration control. The discussion includes the creation of a monitoring plan, the methodology used, results and the specific challenges and solutions found during the blasting process. This study provides a practical guide for similar future projects. Finally, we present a predictive model based on the collected data, offering insights into the vibrations caused by blasting. This model helps decision-makers minimize the risk of displacing rock blocks in the blasting area, improving safety and operational efficiency

Jan 1, 2024

By Joe Dannenberg

A word of preface: The material contained in this talk is not completely original. Many thoughts and actual words come from a fine little book called "1,000 Years of Explosives" by William S. Dutton. The book is now out of print, but if there is enough interest shown by this Society, perhaps we can have it reprinted.

Jan 1, 1980

By Timothy Fogarty, Gregory Poole, Roger Reeder, David Switz

This project involved the construction of a new pump station and intake structure at an existing water treatment facility. Although the project involved a significant amount of rock removal, the specifications said no blasting.

Jan 1, 2012

By Bill Williamson, Doug Richmond, Kerri Kuntz, Gus Gilman, Larry Heywood

This was a description by the poet of what occurred over two centuries earlier to Hannibal’s troops as he passed through the Alps. Interestingly, the pass that many feel is the route that Hannibal chose, Col de la Traversette, is the sight of possibly the earliest avalanche mitigation known. Monastery records describe a tunnel built in 1470, near the top of the pass designed to protect pilgrims from the upper slopes. For the next several centuries, avoidance and reinforced structures were the primary tactics to defend from avalanches

Jan 1, 2009

By Scott King, Norm Patterson, Ruilin Yang

The multiple blasthole fragmentation (MBF) model developed by Orica models the contributions from multiple blastholes to fragmentation at any given point in the rock and simulates a production blast with the actual geometry of the blasted overburden and free faces, explosive loading, multiple decking, and delay timing of each explosive charge. The model has been successfully applied to several open pit mines and quarries around the world, including Canada and the United States. The peak particle velocity (PPV) induced in the rock from the explosive detonation is used in the MBF model as the key parameter relating to the size distribution of the rock fragmentation. Relating the PPV to the rock fragmentation is based on earlier work relating the particle velocity to the dynamic strain in rock. A recent publication further revealed that the PPV is related to the maximum relative displacement that induces three dimensional strain at a point in the rock. The model can explicitly model most of the blast design parameters including explosive properties.

Jan 1, 2018

By Tassilo Baur

Explosives are used in the entertainment industry in a wide variety of applications. Live performances such as automobile races, air shows and the like have incorporated the use of explosives into their programs. Even art work has been created employing explosive materials and techniques. The primary entertainment use of explosives, however, remains in motion pictures, television, theater and related fields where it comes under the auspices of special effects. Much of it falls roughly into the category of demolition, though the object being demolished may range from a cigarette in a person's mouth or clothing worn by actors to large objects such as automobiles, aircraft, or boats. This paper will attempt to provide an overview of the materials and methods by which these special effects are created as well as highlight the unique problems encountered in this field and their often equally unique solutions.

Jan 1, 1992