Search Documents

By Jean M. Bouvet, Pierre M. Vuillaume

There is not just one ANFO: ANFO explosive behaviour depends significantly on the blasting conditions and on its physico-chemical characteristics. For instance, ANFO effficiency increases whereas AN porosity is higher and consequently loading density of the explosive is less. This can be argued against generally admitted ideas. Therefore, the efficiency of industrial explosives related to ANFO (for example "relative weight strength" or "relative bulk strength") is a tool that must be used with caution.

Jan 1, 1993

By Bob Turnbull

The dictionary definition of calibration is: to determine by measurement or comparison with a standard, the corre c t value for each scale reading on a device.1 As a consultant or blast contractor, you assess risk every day. But, have you considered the importance of, and the risks associated with the calibration of your seismograph and the accuracy that is p rovided? Can your calibration pro v i d e r back you up in times of trouble and provide documented evidence that the equipment was functioning within specification? Can their calibration pro c e d u res withstand independent scrutiny and be shown to be traceable to a National Standards for accuracy of measurement? These are important documents that in court provide tremendous support that blasting and monitoring activities are conducted professionally and competently.

Jan 1, 2004

By Jerry Wallace

This project consisted of blasting for expansion of a major interstate natural gas transmission pipeline pump station. The pump station handled 400-500 million cubic feet (1 l- 14 million cubic meters) of gas per day.

Jan 1, 1996

By Douglas A. Anderson

The US Bureau of Mines, in RI 8507, has shown that blast vibrations at low frequency are more likely to cause damage and complaints than those at higher frequency. Since that publication in 1980, the Office of Surface Mining and many state and local regulatory authorities have incorporated frequency in their regulations for acceptable ground vibration from blasting. Even when frequency is not explicitly stated in regulations, it may become an issue in hearings or in court.

Jan 1, 1992

By Eric R. Achelpohl

The paper follows the introduction of a college student into the explosives industry. The opportunity of experiences from classes and work at the University of Missouri-Rolla, along with summer internship experiences are highlighted.

Jan 1, 1998

By Jeff Friedman

This paper addresses certain problems to be encountered when a blasting contractor agrees to provide indemnification. Nearly 100% of all blasting work is performed pursuant to a contractual agreement. Whether the explosives engineering firm works directly for the property owner, or for a general contractor by way of subcontract, indemnification agreements are generally required to protect owners, operators, general contractors, and other interested parties in the event there is subsequent litigation. These contractual requirements are typically referred to as indemnification and “additional insured” agreements. We will address the ramifications of contractual indemnification as well as “additional insured” agreements in this presentation. Some of the aspects of this paper will include:

Jan 1, 2004

By Jhon Silva

"Signature Hole and Waveform Superposition techniques used to predict and control mine blast ground vibrations require a clearly defined information collection configuration. The collection of this information determines the scope and success of the ground vibration prediction. Application of the Improved Signature Hole technique using the Silva-Lusk equation requires the collection of at least two informational elements from any specific production shot. The first required element is a signature waveform, and the second element is the overall production blast waveform. The signature waveform depends on detonated charge variables such as the amount of explosive in use, use of decking, the possible detonation of several holes at the same delay, and many others. The production blast waveform is beneficial to the Improved Signature Hole methodology when used to calibrate the model, and toobtain accurate vibration predictions for different timing configurations."

Jan 1, 2017

By Robert Morgan

The mind-set that only blasters and their helpers need training in explosives can result in risk to other employees working at mine or construction sites where blasting is conducted. Misfires are not always immediately obvious during postblast examinations performed by the certified blaster in charge; the presence of undetonated explosives may not appear until well within the muckpile as was the case in the photo, right. To avoid accidents involving misfires, follow safety procedures specified in mine safety regulations, and the ISEE Blaster’s Handbook that include the following:

Jan 1, 2004

By Greg Shapiro, Paul Dr. Worsey

Mining, quarry, and construction blasts are becoming more and more dependent on bench profiling. The use of accurate profiling gives the blaster better data for the most efficient blast results. So, we ask the question: What is the best method for measuring and analyzing burden?

Jan 1, 2019

By Mauritz Kotze, Jason Furtney, Ewan Sellers, Sandy Etchells, Tom Szendrei

The development of a simple model for gas flow and burden movement has driven the need to improve our understanding of burden breakage mechanisms for single hole blasts and the interaction between multiple holes in solid and jointed rock masses. Conventional analytical understandings of the burden breakout using the elastic-tensile fracture model were studied and found to provide a breakout angle that is independent of burden in contradiction to experimental data. By considering rock fracture in terms of Mohr-Coulomb plasticity using analytical expressions from the field of cavity expansion analysis an improved relationship between breakout angle and burden is derived until the point of critical breakout at which the angle of breakout suddenly changes from between 90 degree and 100 degrees to zero. This suggests that the critical burden occurs at about 0.6 times the radial fracture zone calculated from the analytical solutions.

Jan 1, 2013

By Jay P. Tobin

This paper will address the legal standards applicable to construction blasting lawsuits and offer best practices suggestions for pre-blast inspections, documenting the construction blasting work, recordkeeping, and effectively participating and partnering in the defense of a construction blasting lawsuit.

Jan 1, 2015

By Scott Rosenthal, Kyle Murphy

This paper discusses the trials and tribulations of obtaining Velocity of Detonation (VOD) readings in small diameter blast holes in an underground mine.

Feb 1, 2020

By Scott Rosenthal, Kyle Murphy

This paper discusses the trials and tribulations of obtaining Velocity of Detonation (VOD) readings in small diameter blast holes in an underground mine. Montana Technological University (Montana Tech) obtained a time-domain reflectometer (TDR) type VOD monitoring unit. Purchase of the VOD monitor was justified on verifying explosives performance used in Montana Tech’s practical underground mining class and provide a teaching aid for the school’s rock fragmentation class. Before demonstrating the unit to students, we figured we better learn how to use it first so we give the students an appropriate experience. Our first learning was in obtaining the correct coaxial cable for the VOD monitor and how to properly terminate the cable. Once the cable was on-site and terminated, VOD testing could commence. Use of the VOD monitor was tested underground in small diameter holes (1.5-inch, 38 millimeter) pneumatically loaded with ANFO. After a few failed trials, and follow-up discussions with the supplier, VOD readings were obtained for the ANFO loaded holes. Additional readings were obtained for a pre-split product and detonating cord to satisfy our curiosity that the unit was performing as specified by the manufacturer. This paper will share our learnings in the hopes that others can benefit.

By Jerry R. Wallace

This project consisted of blasting for expansion of a major interstate natural gas transmission pipeline pump station. The pump station handled 400-500 million cubic feet (11-14 million cubic meters) of gas per day.

Jan 1, 1996

By Hans-Peter Rossmanith

Fracture mechanics (Atkinson 1987, Broek 1988, Rossmanith 1978-2002, 1983, 1997, Kanninen & Popelar 1985) and wave propagation (Graf 1975, Rinehart 1975) form the main ingredients in the new electronic detonator based blasting technology. The full potential of using short delay initiation timing in bench and underground blasting can only be exploited if the underlying physical processes are properly understood. From a structural geology point of view, in many open pit mine operations, blasting is performed in incompetent and/or loose rock. Under such conditions the stress waves produced by blasting very quickly dissipate in the rock mass and often their energy cannot effectively be put to work. This contribution shows the effect of open and closed joints – and to some degree also faulting – on the blast wave field and shows the influence of structural geology on the blasting result. A simple engineering method which combines wave propagation and impact mechanics is developed in order to assist the non-scientifically trained blaster in understanding blasting in blocky rock formations. Extensive use will be made of the so-called Lagrange diagram which was introduced in detail in the author’s previous lecture at ISEE 2003 (Rossmanith 2003). This presentation can be considered a continuation of the 2003 presentation.

Jan 1, 2004

By Jim Daley

SEE is a dynamic organization composed of people from all facets of the explosives industry who are truly interested in the advancement of that industry. I had been a miner at the Homestake Gold Mine in Lead, SD for 12 years when I decided to obtain a mining engineering degree. The mental and economic consequences of that decision were more severe than we had imagined. The joint scholarship program of the Northern Plains and Black Hills Chapters of SEE provides assistance to several college students each year. I was fortunate enough to receive scholarships from this program twice and this assistance helped me and my family with both monetary and psychological support during times of need so that we could stay focused on the goal of obtaining a degree.

Jan 1, 1995

By Claude Cunningham

Blasthole pressure is the starting point for many blast design calculations, but the way in which it is usually derived, from measured detonation velocity, indicates that more thought is needed as to its true meaning and implication. The general impression is given that the energy in the hole is defined by VoD, but rarely is this the case. VoD is defined by the energy released in the Detonation Driving Zone between the shock front and the Sonic (or 'CJ') surface, and for commercial explosives it is normal for reaction not to be complete within this zone. Reaction and energy delivery continues behind it, not reflected by VoD. Thus it would be more appropriate to use the theoretical VoD, not the measured VoD, to derive the starting pressure, since this would reflect the energy input of full reaction. In decoupled situations, the derivation of pressure at the blasthole wall using a polynomial decay concept is also of debatable value, and an alternative is offered.

Jan 1, 2006

By Randall M. Wheeler

Many of us have used a seismograph to measure peak particle velocity and frequency. But do we really understand why? Also, why do we measure particle velocity instead of displacement and/or acceleration? What is the vector sum? How do these items relate? Where does frequency fit in? This workshop will attempt to answer these and other questions. Some of the answers may surprise you, others may not.

Jan 1, 1997

By Debra Satkowiak, Ronald Thomas

The Institute of Makers of Explosives (IME), a non-profit safety and security organization founded in 1913, is known for its industry best practices, Safety Library Publications (SLP), some of which have been incorporated into rules by regulatory agencies. The IME developed the first commercial storage, quantity distance (Q/D) table titled “The American Table of Distances” (ATD). It was developed by IME’s legacy association in 1910 and was originally based on observations of structural damage from 117 accidental explosions involving small to very large amounts of explosives, primarily dynamite and black powder. In 1930, the IME published a book, compiled by Ralph Assheton, called the “History of Explosions on Which the American Table of Distances was Based”. The distance in feet in the ATD were founded on the measurements at which inhabited buildings sustained substantial structural damage from the accidental detonation of explosives. For example, minor damage such as window glass breakage and the “shaking down” of plaster was not considered substantial structural damage. Other damage to property that was readily repairable was also not considered “substantial.” It was concluded that unless some integral portion of the building was damaged, the occupants would not be subjected to serious risks.

Jan 1, 2017

By H P. Rossmanith

This contribution addresses the advanced blasting technology which is based on wave propagation theory and fracture mechanics. The new concept of sonicity and the principle of maximizing sonicity in blasting as well as the energy or work of a blast operation will be introduced. It is shown that - in contrast to common belief – it is not the velocity of detonation which controls the blast but the relationship between velocity of detonation and the wave speeds, in other words, the Mach numbers of the blast operation. Based on numerous practical blasts in Germany, the authors show that, when using wave dynamic concepts, there is a linear relationship between peak particle velocity and the work of a blast operation and this linear relationship is controlled by the sonicity of the blast. Extensions to layered and faulted rock masses are presented. It will become clear that a second change of paradigm is enforced, the first one being the implementation of short time delaying. Again, the acquisition of knowledge in wave progation theory and fracture mechanics becomes mandatory in advanced blasting technology, where the art of blasting is now fully transformed into a science of blasting with little room for methods of trial and error.

Jan 1, 2010