Search Documents

By BruneJurgen F., Richard C. Gilmore, Matthew Schreiner, Ray Johnson

Explosive pockets of methane-air mixtures accumulate in underground coal mines and, when ignited, produce an air-blast wave that can disturb combustible coal dust on the floor, roof, and ribs. To prevent explosions, the coal dust must be continuously diluted through application of inert rock dust, usually powdered limestone. Application of powdered dust process creates a respiratory nuisance downwind, where miners cannot work until the dust settles. Rock dust suppliers have developed wet and foam applied products to reduce the nuisance and limit the interruption to mining during dust application. To test the effectiveness of these alternative dust products, researchers at the Colorado School of Mines (Mines) have constructed a full-scale explosion test drift located at the Mines Edgar Experimental Mine (Edgar) to study the dispersibility of different rock dust applications. This paper examines the use of Pentaerythritol tetranitrate (PETN) detonating cord to produce controlled air-blasts that simulate methane-air explosions. The air blasts are generated with curtains of detonating cord that produce shockwaves with wind speeds between 30 to 70 m/s (100 to 225 fps) depending on the length of 5.3 g/m (25 grain/ft) detonating cord used. These velocities represent the minimum air speeds required to trigger propagating coal dust explosions. Researchers have conducted 40 test blasts with various lengths of detonating cord. Results show the two primary waves and two reflected waves each decaying into airblast waves with overpressures of 14 to 27 kPa (2 to 4 psi). Pressures were recorded with commercial piezoelectric transducers and custom-built, bi-directional probes to record the total and dynamic pressures of the wind generated in the explosion. Researchers were able to generate consistent and repeatable wind speeds and air-blast durations sufficiently similar to a methane-air explosion to study the dispersibility of various rock dust products and application methods

Jan 1, 2019

By Douglas Anderson

Even though there is always a feeling of anticipation before a blast is detonated, most blasts are part of a day’s work. Once in a while there is an event that impresses even the most jaded blaster. Few blasts have had the impact of the Kingdome implosion in March of this year. Fortunately for both the Seattle area and the explosives community, the “impact” of the implosion was far less than many local residents had feared. This outcome, of course, was not by chance, but the result of careful planning and design. An urban implosion requires a mix of engineering, logistics, and public relations. Unique challenges on this project tested the resourcefulness of the entire team.

Jan 1, 2001

By C. Morel, P. Fredes, L. Rojas

This article presents a comprehensive study on the development and application of the specific module called "Exclusion Zone" created by Orica to determine blast evacuation exclusion zones. This module, integrated into the "SHOTPlus™ (blast design software)" software, has been used in the context of optimizing equipment evacuation exclusion zones in a northern Chile mine. The main objective has been to reduce the travel times of extraction equipment without compromising the safety of individuals. The module considers various factors such as the explosive charges used, stemming, sector topography, and detonation sequence to determine the rock projection generated by the blast. Furthermore, it utilizes information collected by drones and support tools such as Groundprobe and BlastVision™. The results obtained demonstrate that the use of this technology has allowed the optimization of blast evacuation distances in the northern Chile mine, generating significant economic benefits for the client.

Jan 1, 2024

By David Leidel, Beth Shimer, James Stuart

Periodically, the Institute of Makers of Explosives Safety Library Publications are reviewed, edited and updated to reflect recent technical developments, new commercial explosive products and new regulatory requirements. The rapid proliferation of electronic devices, particularly portable communication systems, inventory management devices, navigational aids, etc., required the revision of the IME Safety Library Publication 20, “Safety Guide for the Prevention of Radio Frequency Radiation Hazards in the Use of Commercial Electric Detonators”. The new edition of SLP-20 has been updated to correct alterations to U.S. frequency allocations and maximum transmitted power permitted and a discussion of communications and tracking systems required in underground mining by the Miner Act. Also, an entire section was added dedicated to safe distances from RF sources to the special type of resistorized electric detonators used in the upstream oil and gas industry on wellsites and an enlarged section describing the particular types of RF sources that the blaster may encounter, perhaps in construction blasting operations.

Jan 1, 2012

By J. P. Proulx, Richard O’Meara, Ruilin Yang

A blast optimization project was carried out at an Open Pit Metal Mine using the Multiple Blasthole Fragmentation (MBF) Model and the Multiple Seed Waveform (MSW) blast vibration model. The aim of the project was to optimize rock fragmentation of the ore blasts to significantly increase metal recoveries while keeping the blast vibration levels at the highwall under control. The project also examined the blasts in the waste rock using the Fragmentation model to expand the blast pattern and select economical explosives for drill and blast cost savings while minimizing any adverse effect on the dig rates. Two sets of near field signature blasthole tests were conducted in both hard ore and relatively soft waste rock. The information from the near-field signature blasthole vibration was used as input to both the MBF and MSW models, as site specific geological information interacting with blasting. The implementation of the full blast design is also input to the MBF and MSW models. A production blast for each rock type was monitored for blast vibration and rock fragmentation. The full blast information and the blast results are used to calibrate and validate the models. The Fragmentation and Vibration model were established for the two rock types at the mine. At each site the Fragmentation modeling was conducted in parallel to the Vibration modeling to ensure blast vibrations were under control while the rock fragmentation was improved. The Fragmentation MBF and MSW are each an integral part of the blast optimization tool. Various scenarios using different explosives, hole delays and blast patterns were modeled for rock fragmentation and blast vibration. The recommendations from the modeling project were to be field trialed at the mine. The implementation of the recommendations was expected to help the mine significantly in terms of the mining economics, and high wall stability and safety.

By Finn Ouchterlony, Gert Bjarnholt, Robert Holmberg

A system for contour blasting with a linear shape charge principle has been studied /10/. In one operation the charge creates two notches along the bore hole wall and breaks the rock mass. The built in notching capability makes it possible to reduce the specific charge and the bore hole pressure to 1/3 of what is used in conventional contour blasting and to ensure that cracks are initiated and propagated only at the notches and nowhere else. The notching capability of linear shape charges has been studied experimentally and the bore hole pressure calculated to aid in optimization of a charge for future field experiments in bore holes with a diameter of about 50 mm.

Jan 1, 1983

By Abraham Lindo

"Blasting plays a key role in hard rock underground mining. It is by nature a violent and destructiveextraction method designed to economically fragment the rock into a suitable size for it to be loaded and hauled as part of the specific mining process while controlling the amount of damage to the surrounding rock mass."

Jan 1, 2016

By Dale Ramsey

As someone who has enjoyed photography as a hobby for many years, aerial photography to me has always been an exciting way to give a different perspective to my images. Our industry is always in search of new technology for bet­ter and more cost effective methods to improve our trade and aerial photography is a great tool to improve project planning or document its progress. It has typically involved conventional aircraft both fixed wing and helicopters but neither method is always available or cost effective. The lat­est innovation since digital imaging is the development of Unmanned Aerial Vehicles (UAVs) or drones. But there is a lot of uncertainty with this amazing new technology’s fu­ture in the U.S. as the Federal Aviation Administration (FAA) is under review and development of UAV regulations for commercial use which are slated to be completed in 2015.

Jan 1, 2015

By Tom Treleaven

The widening of the Panama Canal to approximately 130 feet (40 m) for its entire length began just a few years ago. The original expansion program was slated for completion in 18 to 20 years, but has recently been reduced for completion within the next four years. This means that a tremendous amount of blasting at simultaneous points along the canal, by both the Panama Canal Commission (PCC) and many subcontractors, is necessary to achieve the new completion deadline. The accelerated program also imposed many logistical concerns, since marine trafIic is always heavy and cannot be stopped for blasting. Because some of the large and heavy cargo vessels clear the bottom of the canal by only about 6 feet ( 2 m), the blasting cannot result in any large boulders into the center of the canal, for fear of grounding and damaging a vessel, not to mention the traffic delays and lost income of approximately 1 to 2 million dollars per day.

Jan 1, 1997

By John Hutchings

Drilling and blasting is a clearly delineated work process, which has well defined inputs and outputs. Drilling and blasting is also a process with a number of steps each of which has measurable outcomes. Drilling and blasting is ideally suited to the application of Total Quality Management principles. Most drilling and blasting information is generally poorly managed with disjointed and unrelated Information Technology systems managing parts drilling and blasting data. Data is often moved from on system to another, sometimes manually. In the field, drilling and blasting is still very much a paper based system and which has not generally benefited from some of the recent hardware and software technology advancements now “on the shelf”. Data collected on paper rarely is transcribed back into an electronic system for further analysis. It is often difficult to collate or review historic drilling and blasting data. This paper will present a definition of Total Quality Management and demonstrate how it can be applied to the drilling and blasting work process. Total Quality Management defines the mechanisms for the application of continuous improvement to drilling and blasting. Continuous improvement will provide opportunities to modify drilling and blasting work process outcomes and generate real cost benefits within the overall mining process. A complete drilling and blasting management system frame work, called DBS, is presented in this paper. DBS provides all the components necessary to implement a full drilling and blasting Total Quality Management solution. Also highlighted will be appropriate “off the shelf” technology that can be applied to replace current paper based systems and provide the means to connect with other mine data systems. Various examples will be discussed which will demonstrate potential benefits of applying a structured Total Quality Management approach to a drilling and blasting work process.

Jan 1, 2004

By Virgil L. Lewis

On September 7, 1994, a Burlington Northern coal train crashed into a parked train in the downtown Gillette, Wyoming rail yard. I would like to address two issues in regards to this accident. One, a slide presentation of the damage created by the accident and the resulting required clean-up and two, a simulation of "what if" had there been an explosion during the course of the crash.

Jan 1, 1996

By Shonn K. McNeill, Joshua Micah Hoffman

Security engineering is similar to other forms of engineering – the design is guided by the loads, materials, and desired function. For facility design, the load is the threat. Facilities that are designed with considerations for explosive hazards are designed with a shot, or series of shots, of a given size and distance from key locations. These facilities range from office buildings and industrial sites in developed nations to military and police stations in contingency areas. The challenge is the design shots are not often communicated to facility owners and managers. If the hazards change, whether it’s due to an increased capacity to cause damage by a threat or a decrease in capacity by a structure, not knowing the design shot means not knowing if security design needs to change. Blast modeling is an engineering tool that can be used to reverse engineer what a facility is suitable for, as well as be a tool for modifying security design for new conditions. This paper will examine military and civilian examples, including a case study of a military facility that did not know their as-built conditions and had to be rapidly closed; due to the determination their security engineering shortcomings could not be mitigated.

Jan 1, 2019

By Winfried Rosenstock

The development of electronic initiation systems has partially reached or will reach in a short period of time full reliability for general use without limitations. Unfortunately those systems meet with a fully unprepared mining community and is confronted worldwide with blasting procedures which are not suitable to exploit the full range of the electronic option. This is for the time being only belonging to quarrying and general surface mining, for the use in underground operations the detonator is still not yet competitive, apart from special cases. It is not to be taken in doubts that the introduction for underground purposes will follow in a less shorter or longer period of time.

Jan 1, 2003

By Yoshiharu Tanaka, Toshiyuki Ichijo, Masaaki Yamamoto

We utilized electronic detonators (EDs) to investigate the effect of high detonator delay accuracy on overbreak, remaining rock damage, and surface smoothness, in comparison with that of long-period delay detonators (0.25 sec interval) PDs. The experiments were conducted in a deep mine, in a test site region composed of very hard granodiorite with a seismic wave velocity of about 6.0 km/see and a uniaxial compressive strength, uniaxial tensile strength, and Young's modulus of 300 MPa, 12 MPa, and 73 GPa, respectively. The blasting design was for a test tunnel excavation 8 m in cross section, with an advance per round of 2.5 m. Five rounds were performed, each with a large-hole cut and perimeter holes in a 0.4-m spacing charged with 20-mm-diameter water gel explosive to obtain low charge concentration. EDs were used in the holes on the perimeter of the right half, and PDs were used in all other holes.

Jan 1, 1995

By Peter Duniam, Stephen John Brace

2000 HIGH-TECH SEMINAR Blasting Technology, Instrumentation and Explosives Applications Orlando,Florida,USA July24-27,200O. Objectives:- After completing this session 1. Explain safety issues 2. Do simple initiation design 3. Describe how the system works 4. Demonstrate scanning, hookup, testing and firing 5. Describe hot to do a post blast check 6. Explain how to treat misfired detonators

Jan 1, 2000

By Estefania Aramayo, Jhon Silva, Todor Petrov

Blasting is one of the most critical activities in a mining operation. Nowadays, many quarries have to follow a considerable quantity of environmental restrictions that drive the need to improve the conceptualization, design, procedures, and execution of the blast to comply with all regulations. Airblast is one of the variables required to control when blasting. Airblast is an unwanted side effect of blasting. Airblast is defined as an airborne shock wave resulting from the detonation of explosives. Traditional methodologies used for assessing the overpressure produced by the airblast are based on empirical approximations that require the collection of a series of produced airblasts before they can be used as a predicting tool. Once the data is available, regression analysis methodologies are used to find the constants of empirical laws that, in most cases, establish the relationship between the distance and the weight of explosives used in the shot (scaled distances laws). If using the traditional methodologies, the quality, and representativity of the scaled law established for a particular project are determined in terms of the correlation coefficient; in most cases, the models and their use as a predicting tool are questionable (very low correlation values).

Feb 6, 2023

By D T. Froedge

In 1972 the Kentucky State Legislature enacted House Bill 625 which was known as the Kentucky Blasting Law. This law was enacted primarily to stop problems associated with surface mining, but when it was enacted all industries using explosives were included. The bill was assigned to the Department of Mines and Minerals which created a Division of Explosives and Blasting. At that time, this division only had regulations concerning blasting. One should make a distinction between blasting regulations and other explosive regulations. Blasting is the actual use of explosives, the control of the blasting operation, how much is used, at what distances to buildings, the yardage, and other actions associated with the detonating process, explosives regulations generally including safety to the personnel and the storage of explosives.

Jan 1, 1977

By Ivan Carrasco, Benjamin Cebrian

Mining companies have traditionally organized their structure around a scheme easy to manage: Mining Department and Mill Department. In a challenging landscape for mining, with decreasing grades, increasing rock hardness and more expensive energy, this way to organize departments has resulted in internal disputes and often contradictory targets between both mine and mill. These compete for individual, separated budgets whose Key Performance Indexes often damage each other’s output. The results are increased total production costs and reduction of profits. Some companies have completed the first step in eliminating these inefficiencies by creating Fragmentation Engineers and Fragmentation Superintendents. With all the knowledge available on the overall fragmentation process and costs, in this document an overhaul of the traditional management structure is proposed. Is a step further Mine-to-mill and mine-to-leach programs. Since comminution is the most expensive step of the mineral exploitation, it should be taken as a whole, not divided into competing departments. Thus, mining departments should be re-grouped into: transportation, fragmentation and flotation.

Jan 1, 2014

By David Yanez

The hydroelectric project "El Cajón" is currently under construction in the state of Nayarit, on the Santiago River, in western Mexico. This project is comprised of a Concrete Face Rockfill Dam (CFRD) with a rockfill necessity of 10,5 million cubic meters and it reaches a height of 188 m. The generation equipment includes two turbines with a total installed capacity of 750 MW.

Jan 1, 2006

By Jorge Alvarez

In a large-scale open-pit mining operation, continuous efforts are made to control damage to the slope walls. An essential tool in this effort is determining the PPVc (critical peak particle velocity) in areas of interest. By knowing this value and generating criteria, drilling and blasting designs can be established to reduce vibrations that affect wall construction. It is crucial to understand that the PPVc changes as different mining phases develop, especially due to exploitation on the benches, which leads to vertical inherited damage. Therefore, it is imperative to regularly update the PPVc based on field tests that provide accurate data. With this information, vibration damage criteria can be established, and drilling and blasting techniques can be designed to minimize the impact on the remaining rock mass. This document presents a methodology for generating scaled criteria that best represent the reality of the rock mass.

Jan 21, 2025