Search Documents

By Paul Hopkins

The following methods have been selected from a large number tried while assaying several hundred samples of placer concentrates. It is thought that some of these methods may be useful to those who are required to assay similar products containing large quantities of metallic articles, such as jeweler's sweepings. No great difficulties will be encountered in assaying black sand from beaches or river bars. Such samples require care in grinding and sifting so that no oversize particles of gold or platinum are lost. It is also necessary to have sufficient silica in the flux to form a fluid slag with the excess of iron, magnesium, or chromium which such samples contain. It is much more difficult to assay black sands, or concentrates, produced in large-scale placer-mining operations. These products are usually much harder and more abrasive than the beach black sands. They also contain numerous metallic particles resulting mainly from wear on the mining machinery. These particles consist chiefly of iron or steel but also contain lead, copper, and alloys such as babbitt, solder, brass, ferrosilicon, etc. Fairly large particles of gold are often found. Some samples will contain as much as 10 percent of such metallic particles. It is not feasible to remove the particles of iron with a magnet and discard them, as they invariably contain gold, sometimes a considerable amount. This gold is attached to the iron particles by rust or wedged into cavities. Scraps of sheet iron are often found which have become tightly folded or rolled and contain gold or amalgam within the folds.

Jan 1, 1934

By John D. Prater

Thallium is one of the rarer metals that has come into commercial importance in recent years. Although the element was first reported by Crookes in seleniferous deposits in lead chambers of a sulfuric acid plant in the Harz Mountains of Germany, it had no commercial significance until about 190O because of the high cost of extraction. Thallium occurs widely in the earth's crust but is found in such low concentrations that it is recovered only as a byproduct from processing other elements. There are no domestic ores of thallium; the entire output in this country is supplied by the American Smelting & Refining Co. as a byproduct of its cadmium operations at Globe, Colo. Thallium also is recovered from the flue dusts of sulfuric acid works in which thallium-bearing materials are used and as a byproduct of the lithopone industry. This paper describes methods for recovery of thallium from 'white arsenic" and lead Cottrell-precipitator dust of the American Smelting & Refining Co., lead smelter, Murray, Utah. Owing to an enlarged market for thallium because of increased military requirements and expanded peacetime uses, the Salt Lake Station of the Bureau of Mines surveyed the occurrence of thallium in ores, concentrates, and smelter products from all parts of the nation and found the most promising source was certain smelter products of the American Smelting & Refining Co. plant, Murray, Utah. Much of the thallium was being lost in marketed arsenic products; therefore, this investigation was undertaken to develop methods for recovering the thallium.

Jan 1, 1952

MFIRE is a computer simulation program that performs normal ventilation network planning calculations, and dynamic transient state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under thermal and mechanical influence. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters, external influences such as temperatures, and internal influences such as fires. Extensive output enables detailed quantitative analysis of the effects of the proposed alteration to the ventilation system Network simulation using digital computers has become widespread throughout the mining industry in recent years. However, as the sophistication of the simulator increases (MFIRE, for example), the complexity of input data requirements and interpretations of results requires more skill and knowledge from the users. Perhaps the most difficult part of using MFIRE is to construct the data set describing the mine's physical layout and its ventilation properties. The initial attempts to get the data set running often reveal unknown or ignored aspects of the mine's ventilation. MFIRE was written in Fortran 77 and compiled with Microway1 Fortran for the Intel 80386 based computers with a 80387 math co-processor. The source code is portable and available for users who wish to modify the source code to operate on other computers. This user manual describes the development of MFIRE, the input format and requirements, the output, common errors, fire parameters, and examples MFIRE application. Valuable reference material is included in the appendices. Knowledgeable users may skip directly to the PROGRAM INSTALLATION AND OPERATION section to begin using MFIRE immediately.

Jan 1, 1995

MFIRE is a computer simulation program that performs normal ventilation network planning calculations, and dynamic transient state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under thermal and mechanical influence. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters, external influences such as temperatures, and internal influences such as fires. Extensive output enables detailed quantitative analysis of the effects of the proposed alteration to the ventilation system Network simulation using digital computers has become widespread throughout the mining industry in recent years. However, as the sophistication of the simulator increases (MFIRE, for example), the complexity of input data requirements and interpretations of results requires more skill and knowledge from the users. Perhaps the most difficult part of using MFIRE is to construct the data set describing the mine's physical layout and its ventilation properties. The initial attempts to get the data set running often reveal unknown or ignored aspects of the mine's ventilation. MFIRE was written in Fortran 77 and compiled with Microway1 Fortran for the Intel 80386 based computers with a 80387 math co-processor. The source code is portable and available for users who wish to modify the source code to operate on other computers. This user manual describes the development of MFIRE, the input format and requirements, the output, common errors, fire parameters, and examples MFIRE application. Valuable reference material is included in the appendices. Knowledgeable users may skip directly to the PROGRAM INSTALLATION AND OPERATION section to begin using MFIRE immediately.

Jan 1, 1995

By John D. Foulkes, David A. Curtis, Robert L. Lagace, John L. Rothery

An investigation is made of the feasibility of developing compact transmit antennas and/or other means to efficiently couple VLF to MF band radio energy between portable wireless communication units in coal mines. The completely wireless communication ranges between two portable radios equipped with practically-sized reference loop antennas in representative coal mine environments are estimated. Antenna technology is assessed with respect to transmit moment, range, intrinsic safety, battery and wearability requirements to deter- mine the most suitable antenna types for use by miners. It is concluded that air-core bandolier loop antennas, and perhaps ferrite-loaded loop antennas, having peak transmit moments of about 2.5 ampere-m5 will be the most effective antenna choices for portable units. This choice, however, will not allow the range goal of 1350 feet to be attained in mines having unfavorable signal attenuation and noise environments. Rectangular air-core loops are compared with grounded horizontal-wire and vertical-wire mode exciters for fixed station applications. The potential for significantly increasing the wireless communication range by inductively coupling to communications and power lines in a mine is evaluated and found to be considerable based on theoretical coupling equations. Lastly, the theoretical performance of a hybrid noise cancelling diversity receiving technique that utilizes both the electric and magnetic field components of the ambient noise to improve the receiver output signal-to-noise ratio under certain adverse conditions is estimated and shown to be favorable when the magnetic and electric field noise components are highly correlated.

Jan 1, 1977

By Henry C. Meeve

This report describes work done in the Creede Mining district, Mineral County, Colo., in 1965-66 as a part of a Bureau of Mines study of the silver production potential of the United States. The ruining history of the district is briefly covered, and representative former and current mining operations are described. Mining and milling costs of the Emperius Mining Company's operation are given in some detail as being representative of the cost of mining typical Creede ore bodies under current technology. An estimate of the silver reserves and resources of the district is presented, subject to many uncertainties stemming from inaccessibility of old workings, lack of mining records, and low level exploration activity, all of which limit the opportunity to accurately evaluate ore potential. The report concludes with an analysis of future silver production trends in the Creede district. An increase of silver production to as much as I million ounces yearly is projected, possibly starting in 1969. As long as ore bodies in the zone of enrichment, in which silver is a major constituent, contribute a substantial part of Creede production, silver price will affect overall production rates appreciably. As the richer are bodies become depleted, an increasing portion of production again will be coming from primary sulfide ores in which silver is a byproduct of lead and zinc. When this occurs, the level of silver production will be governed chiefly by lead and zinc production and prices and can be expected to decline to the 1960-66 level, which amounts to an average of 240,000 ounces per year.

Jan 1, 1968

By William Wiehagen

This trainer?s guide is designed as a reference manual. The purpose is to offer information and examples to skills trainers to assist them in structuring training for new operators of Walk-Thru roof bolting machines. Trainers can use this manual as a resource for helping trainees learn, understand, and apply knowledge and skills. In this sense, the guide is not prescriptive. It is designed to offer information and trigger ideas on what might be done to accelerate learning to those who are new to the roof-bolting task. On-site trainers can modify this guide to fit their conditions, machines and equipment, and work procedures. They can integrate roof control plans, company policies and procedures, and operators? manuals from the manufacturers of the original equipment into this guide. Every trainee is different and will come to the job with varying levels of relevant knowledge and skills. The trainer?s decisions on where to start, how to organize the on-the-job and classroom training portions, and when and how to offer different aspects of the training will be based on (1) a pretraining assessment of the trainee?s knowledge and skills and (2) the trainer?s experience in conducting skills training. The ?Skill Check? section might be useful for deciding where training should start among miners who have underground experience but limited knowledge of roof-bolting techniques. Every job carries a learning curve and likely has a number of ?teachable moments? where significantly new knowledge and skills can be learned.

Aug 1, 2006

By T. L. Joseph

"In the January 3 issue of Iron Trade Review, Sweetser2, in referring to the problem of coke combustibility, points out that, ""Someone should formulate a rule for the rate of flow of coke through the zone of coke combustion that now appears to be confined to a comparatively restricted volume in front of the tuyeres,"" In formulating such a rule it is necessary to distinguish clearly between combustibility, a property of the fuel, and rate of combustion, which is determined by the rate at which air is supplied to the fuel bed. The rate of carbon gasified at the tuyeres of a blast furnace is independent of coke combusti-bility. A fast-burning coke will burn in a more restricted volume than a slow-burning coke, but both types of fuel will be consumed at rates determined by the supply of oxygen,A number of the definitions of combustibility that have appeared in technical literature relate more closely to rate of combustion than to combustibility. Perrott and Kinney) have correctly defined it as follows: ""Combustibility of coke from the standpoint of its use in, the blast furnace is inversely proportional to the mean rate of gasification per unit volume of the combustion zone, assuming other factors remain constant,"" Combustibility of coke refers therefore to those properties that determine the size or extent of the combustion zone. Relative differences in these properties can be measured by the depth of the fuel bed required to convert oxygen from the air into carbon monoxide."

May 1, 1924

By Thomas E. Marshall, Timothy Batchler, Anthony T. Iannacchione

As the amount of new fractured surfaces or "damaged rock layers" within roof rock increases, the stability of the rock mass decreases. While direct measurements of this phenomenon are not easily made, there is good circumstantial evidence to support this hypothesis. For example, it is common to observe increased cracks or fractures in the immediate mine roof rock before a roof fall. Likewise, roof drill holes placed in areas that later fail often reveal increased numbers and/or separations of fractures within the rock column through time. And finally, the frequency of microseismic activity, representative of rock fracturing, increases before a roof fall. For this study, more than 700 microseismic emissions were collected from two underground limestone mine roof fall areas in southwestern Pennsylvania. Microseismic events were located and magnitudes determined using the moment magnitude technique. Moment magnitude is based on the event seismic moment, which is a measure of the seismic deformation. The amount of new fracture surface length was calculated based on the stored strain energy within the rock prior to fracture. In the two case studies presented, a significant amount of microseismic activity was observed as much as two days before the first signs of failure in the roof fall areas. Additionally, results from this analysis reveal much about the behavior of strata prone to failure and allows for the construction of hazard maps based on microseismic emissions. The potential use of this technique as a means of anticipating roof falls is analyzed and discussed.

By E. P. Carman

In this report, the Federal Bureau of Mines presents a summary of the occurrence, properties, and uses of some natural bitumens, using the layman's or dictionary definition of bitumens - that is, naturally occurring hydro-carbons. Emphasis is on the less common solid and semisolid bitumens, particularly those occurring or used to some extent in the United States. This comprises data from many sources and references to these sources for more detail than is given in this summary. This paper was prepared primarily to answer questions about some of the less known bituminous materials. The word hydrocarbons could just as well have been substituted in the title for bitumens, but bitumens was used, since an abstract of the paper was presented at a meeting where the major emphasis was on bituminous materials. The reader will realize that coals, of which only the more unusual such as the cannel coals and torbanites are discussed in this paper, are primarily mixtures of bituminous materials and carbon. The amount of bituminous material, or volatile matter, in coals is greatest in the lower rank coals and the unusual types described in this paper, and decreases as coal rank increases. However, since no method other than destruction of the original coal substance by heat is known that will separate the volatile matter from the carbon, it appears reasonable to classify the coals with other bituminous materials, particularly since bituminous coal - the most widely used coal - by its name indicates the combination of bituminous materials and carbon.

Jan 1, 1961

By Fred N. Kissell

A parachute-type stopping intended for changing the course of mine ventilation air during mine emergencies has been designed and tested. Some production uses are also visualized for metal mines. Preliminary tests in the laboratory and underground indicate that the parachute stopping is a workable concept, but further developmental research is required.

Jan 1, 1975

By W. M. Myers

Water has been commonly used as a collecting medium in many instruments employed in the sampling of dusty atmospheres in mines** add industrial plants, and for this purpose has much to recommend it, particularly the following factors:1.,Water is a very efficient dust collector.2.,Distilled water of great purity may be readily obtained at slight expense. The analytical error introduced by the extremely small amount of foreign matter in carefully distilled water is very small,3.,Water is a very convenient medium with which to work as all the analytical operations of diluting, aliquoting, and filtering are readily and speedily carried out. Water has therefore been used extensively in such instruments as the Palmer apparatus, the Greenburg-Smith impinger, and the dust collector recently described by Drinker, Thompson, and Fitchet. The Bureau of Mines has conducted investigations in many metal-mining districts of the country, determining of dust the nature and amount of dust present in working places, its effect the health of workers, and what precautions may be taken to decrease the hazard of exposure to dangerous dusts. The Bureau is therefore interested in any factor that affects the accuracy of dust sampling.

Nov 1, 1923

By Ronald T. Mayerle

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 20,500-acre part of the 104,085-acre Rincon Wilderness Study Area (OR-002-082) in order to evaluate its identified mineral resources. The wilderness study area is located in Harney County, OR, about 12 miles west from Fields. No mineral resources were identified within the study area. A literature search found no records of mining or minerals exploration, nor did a ground search find any evidence of mining-related activity. Of seven alluvial samples taken from the major drainages of the study area, all were barren except one. This sample, taken from a dry streambed along the southern boundary, contained $0.07 gold per cubic yard; however, this small amount of gold is of no economic significance, and the source is probably outside the study area. The Pueblo-Steens mining district extends to within 4 miles east of the study area. No evidence of geological environments similar to those that were responsible for the formation of resources or occurrences of metals and nonmetals within the district is known within the study area.

Jan 1, 1987

By J. B. Zadra, S. M. Shelton, M. M. Fine

"Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced; although it is well known that there are large deposits of low-grade ore in the United States, the production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stockpiled ore is depleted through inability to procure adequate supplies from foreign sources. Consequently, a program of laboratory and pilot-plant investigation designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines.This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program. The scope of the program and the organization that woo set up to direct and supervise the work were discussed in the foreword of the first paper of this series, Report of Investigations 3606, Manganese Investigations. 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent, and C. R. Schack. Other reports will be published as the work progresses."

Mar 1, 1942

By John R. Benham

The Bureau of Mines examined the Bear Canyon RARE II area in 1982. The area has no identified mineral deposits. The few claims that were located in the study area are devoid of any workings. No concentrations of economic minerals were found in the samples taken. There are no mineral, geothermal, or oil and gas leases in the area; the nearest oil well is 10 mi (16 km) east. The nearest mining operation was the Ruby Gold Placer worked in 1914, 7 mi (11 km) southeast (Hart, 1966, p. 45); the Pliocene Paso Robles Formation which contained the gold does not extend into the area. SETTING The Bear Canyon RARE II area covers 19.7 sq mi (51 sq km) or 12,600 acres (1500 ha) in west-central California. It lies in the Santa Lucia Range 10 mi (16 km) southwest of King City and adjoins the southeast side of the Ventana Wilderness. It is 10 mi (16 km) from the Pacific Ocean. Primary access is by the San Antonio River road on the Hunter Liggett Military Reservation, which parallels the area's southern border. Further access to the area's interior is by jeep and foot trails.

Jan 1, 1983

Horizontal holes are drilled underground into coalbeds to control methane flow from ribs and active face areas and to make gas pressure measurements in coalbeds. Gas pressure measurements are made by drilling the same hole incrementally. After each increment, the hole is filled with some type of packers and allowed to reach equilibrium before a gas pressure reading is taken. As the length of hole increases, more packers are required to effect a seal and obtain a reliable pressure measurement. Problems have been encountered in obtaining satisfactory packer seals due to the friable nature of the coalbed. New methods of packing the holes must be used. Therefore, this project was established to evaluate materials and develop a new technique in which a semiliquid and/ or rigid type grout could be placed in the hole to provide satisfactory sealing.

Jan 1, 1972

Metals From Oil Shale. -A Geological Survey News Release in mid-January indicated that a surface sample analysis of oil shale in central Montana found a ton of shale to contain up to 13 pounds of zinc, 2 pounds of nickel, 1.8 pounds of molybdenum, 16 pounds of vanadium oxide, and nearly a quarter pound of selenium. It might be possible to recover some of these metals economically on a byproduct basis. The shale in central Montana was also estimated to contain 180 billion barrels of synthetic crude oil, which compares to estimated oil reserves in the Middle East of 360 billion barrels. Merchant Fleet Dwindles. -The National Maritime Council reports that although the U.S. is the world's largest trading power and that well over 90% of its foreign trade is conducted by shipping, the U.S. fleet is tenth in absolute numbers and less than 5% of its foreign trade is carried on U.S. ships. In 30 years, the U.S. fleet has dwindled from over 4,000 oceangoing vessels to about 600. U.S. ships carry less than 2% of imported iron ore, bauxite, and tungsten, and only 3% of oil imports.

Jan 1, 1981

By Hendrik Gerritsen

The research to be described is directed to the construction of an instrument that detects methane in air. The principle on which it is based is that methane gas absorbs infrared radiation in the wavelength range of about 3.2 to 3.4 micron. Solid state p-n junctions of composition In, .97Ca.03As emitting radiation in a band centered at 3.3 micron were grown by liquid epitaxy on InAs. Fight separate growth cycles and a total of 200 diodes were measured to determine total power, wavelength peak, spectral. half width and reproducibility of the method. In order to compensate for temperature changes, dual emitter systems (one InGaAs, and one InAs diode) mounted on the same TO-5 header were made. These devices were imaged, using a folded optical path cell, on large area InAs detectors, grown by a planar diffusion technique. In the 0-50°C range the primary temperature sensitivity is in the InAs detector rather than in the emitters. Several methods to reduce the overall temperature sensitivity to within acceptable limits were demonstrated. Humidity was shown to have a negligible effect on the measurements.

Jan 1, 1976

The largest producing coal field in Alabama, the Warrior Coal Field, was discovered in 1821'. Since then, coal has become Alabama's leading industrial mineral, both in production and income. Alabama has traditionally been one of the nation's major coal-producing states. This level of production is expected to continue due to Alabama's high-quality, low-sulfur coal. Alabama produces both bituminous and lignite coal. The bituminous coal is mined by underground and surface methods from four major coal fields in 24 counties. Alabama's lignite deposits, which are located in the southern part of the state, are not presently being mined. However, Alabama lignite is high-grade, and deposits are very shallow and easily surface-mined. Alabama gained primacy when its regulatory program was conditionally approved May 20, 1982. The program was fully approved July 5,1984. Alabama's Abandoned Mine Lands program was approved May 20,1982, and its emergency program was approved January 23, 1991. Although a Federal Lands Cooperative Agreement between Alabama and OSM became effective August 30,1985, no coal mining is currently taking place on federal lands in the state.9

Jan 1, 1992

By Dennis Dolinar, Russell Frith, David Oyler, Christopher Mark

Unusual circumstances may require that a longwall retreat into or through a previously driven room. The operation can be completed successfully, but there have been a number of spectacular failures which exposed miners to serious roof fall hazards. To help determine what factors contribute to such failures. the National Institute for Occupational Safety and Health (NIOSH) compiled a comprehensive international database of 130 case histories. The cases include five failures where major rock falls occurred in front of the shields, and six even more serious failures involving major overburden weighting. This suggests two room failure mechanisms The first is a roof fall type failure caused by loading of the immediate roof at the face as the fender narrows. The second is a weighting type failure caused by the inability of the roof to bridge the recovery room and face area, and affecting rock well above the immediate roof The data indicate that the roof fall type of failure is less likely when intensive roof reinforcement (bolts, cables, and trusses) is employed together with higher-capacity shields The overburden weighting failures, in contrast, occurred when the roof was weak and little standing support was used