Search Documents

By David K. Hylbert

This study was designed to investigate roof falls in room-and-pillar drift coal mines and to determine geologic methods for predicting unstable roof conditions. The study area was located in Harlan County, Kentucky and the Bailey Creek (Harlan coal bed) and Highsplint (Darby coal bed) mines were selected for study. Correlations were made laterally between surface outcrops and within the mines using lithologic and trend analysis criteria. Lithologic criteria compared cyclic changes in roof strata. Results indicated that roof falls are associated with zones of weakness within or between five vertical cycles recognized. Abrupt lateral facies changes occur. In the Highsplint mine the roof was classified in four categories or conditions using 98 rib sections for control. Structure contour and isopach maps were used to project axial trends of the sandstone roof. A roof-fall zone was examined using ten NX cores taken from the roof and included lithologic, petrographic and clay mineral studies. At the Bailey Creek mine roof failure was caused by the heading direction being driven subparallel to paleochannel directions. Computer programs were used in trend analysis studies. Cross-bedding, paleo-channel trough axis and sole mark studies indicated a 350 discrepancy between surface and in-mine trough axes at Highsplint. A direct relationship between joint and "slip" frequency and direction with sandstone roll trends was found. Surface joints compared well with drainage Segments, hilt did not correlate with roof falls in areas of mines under overburden in excess of 600 feet.

Jan 1, 1977

By Allan F. Smith

The influence of hydraulic fluids on spontaneous heating in bituminous coals is determined by measurement of the temperature increases produced in coal-fluid mixtures heated to a temperature sufficient for the initiation of self-heating. Similar tests on as-received coal samples and water-coal mixtures are compared with the results obtained for the various hydraulic fluids. Three of the four coals were sampled from coalbeds known to have a history of spontaneous heating. The data provide a basis for predicting the possible effects in gob or carbonaceous refuse of coal mines.

Jan 1, 1963

By W. L. Barry

A review of the practices of analyzing for precious metals at the Reno Research Center, U.S. Bureau of mines, is presented. A general description of fire assaying, the physical layout of a fire assay laboratory, and the use of fire assaying in combination with atomic absorption, induction coupled plasma, and emission spectroscopy is reviewed. The combination of techniques significantly decreases the detection limits for precious metal analyses and simplifies the analysis of the platinum-group metals. Methods of protecting personnel from ingestion of lead are also discussed.

Jan 1, 1982

By Oliver Bowles

"A New Mica Company in China A report has been received from the American Consulate at Chungking, China, to the affect that a new company has been organized to operate a mica mine north of Ta-chien-lu, in the province of Ssu-Chuan. The company, which is entirely under Chinese management and control, has a working capital of $10,000. While comparatively new, the mine has been worked before, and apparently with some success. The mica is said to be of good quality. It is claimed that the deposit will supply a limited amount of mica that will cut in pieces a foot square or over, and larger quantities of smaller sizes. The chief difficulty is transportation, for it is reported that a ten days' journey, part of it over mountain trails, will be necessary to transport the mica from the mine to Yachow, the nearest practical waterway. It is probable, therefore, that the output of the mine will be limited.Necessity for Careful Trimming and Grading of MicaA recent report to the Department of Trade and Commerce, Ottawa, Canada, by Acting Trade Commissioner C. G. Venus, London, England, contains information which is of vital interest to mica producers in the United States. It is pointed out that mica exports from Canada to England show a gradual decline dur¬ing recent years, the figures being as follows: 1913- 1,383 cwt: 1914 - 1,225 cwt: 1915 - 1,864 cwt: 1S16 - 879 cwt: 1917 444 cwt: 1918 - 480 cwt. Shipments from India to England, on the other hand, show a steady increase from 40,178 cwt. in 1913 to 66,401 cwt, in 1918."

Jan 1, 1920

By William J. Campbell

Three types of X-ray analytical instrumentation were compared for applications in the secondary brass and bronze industry. The instruments were a conventional X-ray spectrograph, a portable X-ray spectrograph, and a radioiso-topic X-ray analyzer using balanced filters. The following two general applications were considered: Rapid identification for sorting scrap metals and quantitative analyses to provide guidance in the melting and casting of alloys. Twenty-three analyzed copper-base alloys were used as standards. Although the alloys varied widely in composition, matrix correction procedures were not necessary except for copper. The conventional X-ray spectrograph provides positive identification of the alloys and quantitative values for the six elements investigated--aluminum, copper, iron, lead, tin, and zinc. Equivalent results were obtained with the portable X-ray spectrograph for those elements whose characteristic X-rays are in the wavelength range of the instrument. The radioisotopic X-ray analyzer distinguishes certain groups of alloys and provides quantitative determinations for copper, lead, tin, and zinc. The sensitivity of the analyzer was marginal for the determination of small concentrations of elements of atomic number 26 or lower.

Jan 1, 1972

By Paul E. Loustaunau

This report describes a project in which three structured underground coal mine equipment operator training programs were developed. The project was carried out in two parts. In the first part, a research study was conducted to determine how on-the-job training is currently conducted in industry, and to determine the overall effectiveness of current on-the-job training. In addition, the possible application of the principles of social learning theory to on-the-job training was investigated. In the second part three prototypes on-the-job training programs were developed for shuttle car operation, roof bolter operation, and continuous miner operation. These programs were carefully structured to eliminate the shortcomings of current industrial on-the-job training identified in the research study and incorporated the application of relevant principles of social learning theory. The programs are prototypes which underground coal mine training personnel can use as models to develop their own customized equipment operator training programs.

Jan 1, 1983

By J. L. Holman

The Bureau of Mines is conducting research to improve technology for the recovery of strategic and critical metals, such as cobalt, nickel, and chromium, that are lost in bulk and particulate superalloy-type scrap because it has not been possible to process mixed contaminated scrap efficiently. The research approach involves melting and casting mixed superalloy scrap into soluble anodes for electrodeposition of Ni-Co alloys by controlled-potential electrolysis. The initial experimental results described in this report are from electrolytic tests us-ing alloy anodes cast from elemental nickel, cobalt, and chromium, the main constituent metals of superalloys. Baseline data and operating parameters are necessary for Ni-Co and Ni-Co-Cr alloys before detailed experiments can be conducted on the more complex superalloy scrap. This basic research assessed the effects of cathode potential, S04:CI electrolyte ratio, electrolyte pH, stirring rate, deposition time, cathode current density, and chromium concentration on cathode current efficiency, alloy deposit composition, and deposition potential at a cell temperature of 55° C.

Jan 1, 1985

By Robert W. Decker

This report presents a survey of published novel coal cutting (mining) concepts and a brief discussion of each one. A preliminary evaluation follows which identifies promising concepts, emphasizing reduced dust generation and economic production potentials. The promising concepts are then studied more deeply and evaluated in more detail with recommendations given for further development action. The concepts recommended for further work include: Roan and Pillar Mining: Deep Cutting Continuous Miner Linear Cutting Rotary Head Miner Longwall Mining: Oscillating Continuous Water Jet Miner Deep Cutting Shearer

Jan 1, 1981

By Charles H. Shapiro

[In July, 1924, the Bureau of Mines, through its Petroleum Experiment Station, undertook a field study of methods used in oil-field shops for dressing and tempering fishtail bits. The purpose of this work was to suggest chances that would be helpful to the bit-dresser in turning out better treated, harder, and tougher bits, and thus cut down the excessive loss of time caused by too frequent changing of bits. It was the intention to eliminate as much as possible the guess work connected with dressing and tempering bits under the method of judging temperature by eye, by developing; practical methods of controlling temperature. If there were some possible means of accurate temperature control, then it would be an easy matter to bring all bits to the proper temperature for maximum hardness rued toughness, thus doing away with the source of most of the trouble experienced in the present method of bit tempering. Shortly after the Bureau of Mines began its study, a chop In the Stroud, Oklahoma, oil field announced method for tempering fishtail bits that Would increase the drilling footage of each bit treated. The method accurately regulates, by the use of a bath of molten salt, the temperature to which a bit is heated before being quenched to produce hardness. There is nothing new in using silt baths for the, heat treatment of steel, but this was the first attempt to introduce it into the oil fields for use in hardening bits, and for this purpose it proved to be admirably adapted. In tempering, by the old system it is not possible to measure the temperature of the heated bit by means of an electrical instrument for that purpose, whereas this is an easy matter with the now method. If heating steel to slightly above the critical point rind quenching suddenly will bring out its best properties, their here is a method of accurately bringing the steel to that point.]

Jan 1, 1925

By Ben Aleck

The objective of this program was to adapt Space Shuttle technology on high-performance spherical pressure vessels to cylindrical pressure vessels. Specifically, a cylindrical aluminum liner overwrapped with fiberglass filaments and prestressed by yielding the liner under a sizing pressure was to be replaced by a higher strength-to-weight ratio steel liner overwrapped with a higher strength-to-weight ratio filament. The steel was cryoworked stainless steel and the new fiber was Kevlar 49. In addition, the heavyweight ends of the aluminum liner were to be replaced by thin-walled domes which required multiple helix angle wraps for their support, in place of the single kite-string wrap from pole to pole of the aluminum overwrapped design. The use of cold swaging of tube-ends to form bosses, demonstrated on subscale development efforts, had not been achieved full-scale when the contract was initiated. Difficulties arose with the full-scale demonstration which were not solvable at the time with the designs and equipment available. hence, an unanticipated development was the finally selected method of making the 4-in.-diameter stainless steel liner with a single boss and no welds in an 0.020-in.-thick wall, from an 0.050-in.-thick, 13-in.-diameter disk. The demonstration vessel failed by leakage during the prestressing step because embedded oxides had formed flaws in the boss region. Such flaws have been avoided by proper temperature control during hot spinning. Hence, a new design was developed which weighs half as much as its recently developed predecessor. Funds ran out before adequate testable hardware was produced.

Jan 1, 1983

To reduce operator exposure to noise from vibrating screens at coal preparation plants. Background Hearing loss is one of the most common occupational illnesses in the United States. In the U.S. mining industry, hearing loss is 2.5 to 3 times greater than what is expected for the average population that is not exposed to occupational noise. Furthermore, studies by the National Institute for Occupational Safety and Health (NIOSH) showed that by age 50, 90% of coal miners have a hearing impairment versus only 10% of the population that is not exposed to occupational noise. A NIOSH cross-sectional survey of coal preparation plants showed that 43.5% of employees were overexposed to noise. The study also found that vibrating screens were one of the top five loudest types of equipment at these plants?as well as the most numerous?making them a key noise source to address.

Nov 1, 2009

By G. S. Scott

In the course of the investigation into the causes, behavior, and control of mine fires, which the Bureau of Mines is now conducting, some attention was given to the subject of spontaneous heating. It is self-evident that the temperature of a pile of broken coal will rice if the rate of generation of heat exceeds the rate of brat dissipation and will fall if the opposite is the case. Factors that affect the rate of generation of heat are:

Jan 1, 1941

By G. S. Scott

In the course of tire investigation into the causes, behavior, and control of mine fires, which the Bureau of Mines is now conducting, come attention was given to the subject of spontaneous heating. It is self-evident that the temperature of a pile of broken coal will rise if the rate of generation of heat exceeds the rate of heat dissipation and will fall if the opposite is the cane. Factors that affect the rate of generation of heat are:

Jan 1, 1941

By T. R. Achenbach

1. This, the final report to the U. S. Bureau of Mines on the program with the subject title, presents the data obtained from June 29, 1973, to April 20, 1974. 2. Operating in the Illinois #6 coal seam, the effectiveness of foam opposed to water was compared in reducing respirable coal dust. A combination of 39 foam generators and 14 water sprays were used during the foam tests. Sixty one water sprays were operated during the water tests. Data from 24 shifts using foam and 21 shifts using water are presented. 3. Additional work on foam generator design should be undertaken to provide coverage to a wider area with foam. 4. The general attitude of those working on the foam program and with the miner at the face was positive. It is urged that the work be continued. 5. The minor respiratory irritations evidently caused by an aerosol effect of the surfactant should be investigated. 6. The statistical analysis of the tests will be made and reported by the U. S. Bureau of Mines.

Jan 1, 1974

By M. B. Cooke, A. D. Bauer, E. W. Dean

The Bureau of Mines is collecting and analyzing representative samples of crude petroleum from all the producing fields in the United States , and the results are being published in a series of reports that are preliminary to the issue of a bulletin covering the entire survey . The bureau has recently completed a survey of crude oils from the Kansas district . In all 27 samples were collected and analyzed , under the direction of A. W. Ambrose , chief petroleum technologist of the Bureau. Valuable assistance was received through the cooperation of oil companies operating in the State , especially the Prairie Pipe Line Co. , and the Empire Pipe Line Co. The present report issued as Serial 2322 , on the Kansas crudes , forms the fifth of the series . Of the four previous papers , the first ( No. 2202 ) deals with crudes from the Eastern fields of the United States , the second ( No. 2235 ) with crudes from the Rocky Mountain district , the third ( No. 2290) gives additional data , cn viscosities and pour tests , for the crudes from these two fields , and the fourth ( No. 2293 ) covers the fields of northern Texas , northern Louisiana , and Arkansas . The details of the methods of collecting samples , making laboratory tests and interpreting results , have been discussed in these earlier reports . It has also been pointed out that the only adequate method of interpreting analyses of crude oils is to compare the individual reports with the analysis of some crude oil that is familiar to the operator . For this reason , no comprehensive discussion of the results of the Kansas survey is attempted, although some general statements may be made .

Feb 1, 1922

By Wesley T. Holmes

This report describes the first phase of an investigation aimed at obtaining a wider knowledge of the problems involved in smelting titaniferous magnetites. Liquidus temperature measurements were made on selected slag compositions in the titania-alumina-silica-calcia-magnesia system. Both the melting-holding-quenching method and the hot-stage microscope method were used in the tests. Liquidus temperatures of slags studied ranged from 1,217° to 1,667° C. The lowest liquidus temperature of the slags occurred when the difference between CaO plus MgO and Si02 was less than 12 weight-percent. Liquidus temperatures were also lowered when Si02 was substituted for Ti02 plus Al2O3 when CaO and MgO levels were held constant. Improved methods for the measurement of liquidus temperatures on very small samples are described.

Jan 1, 1968

By F. A. Jones

Increased mechanization .of coal mines has emphasized the need for study of actual power requirements of the various machines employed in the production of coal and losses in the distribution of power to these machines. These studies are being made in order that hazards, excessive use of power, and high maintenance cost of equipment resulting from these losses may be analyzed and eliminated where possible. Research on the use of electric power in-coal mines was suggested by the Advisory Committee of the Bureau of Mines in 1937, and it was decided to begin with a study of individual machines of various types under operating conditions in modern coal mines. The transmission of power, particularly line losses and inadequate return circuits, should be a part of the investigation. This report presents some of the data of an initial study in commercial mines. ACKNOWLEDGMENTS The superintendents, engineers, and other officials of the two mines studied cooperated fully and aided in setting up and transporting the test equipment, giving such information as was requested.

Jan 1, 1942

By F. A. Jones

Increased mechanization .of coal mines has emphasized the need for study of actual power requirements of the various machines employed in the production of coal and losses in the distribution of power to these machines. These studies are being made in order that hazards, excessive use of power, and high maintenance cost of equipment resulting from these losses may be analyzed and eliminated where possible. Research on the use of electric power in-coal mines was suggested by the Advisory Committee of the Bureau of Mines in 1937, and it was decided to begin with a study of individual machines of various types under operating conditions in modern coal mines. The transmission of power, particularly line losses and inadequate return circuits, should be a part of the investigation. This report presents some of the data of an initial study in commercial mines. ACKNOWLEDGMENTS The superintendents, engineers, and other officials of the two mines studied cooperated fully and aided in setting up and transporting the test equipment, giving such information as was requested.

Jan 1, 1942

By Joseph Cervik

Coal is a soft and brittle material. Drilling rates in the Pittsburgh coalbed using a drag bit exceed 3 ft/min at 2,500-pound thrust. However, maintaining the bit on a horizontal trajectory or parallel to bedding planes to attain lengths of 1,000 feet is difficult. This Bureau of Mines report presents a drill string configuration that can be guided through the coalbed. The angle of the borehole is measured periodically and by proper combinations of bit thrust and rotational speed (r/min), bit trajectory can be lifted or dropped to keep the bit in the coalbed. An example of a hole drilled to 2,126 feet is presented to show levels of thrust and rotational speed used to lift or drop the bit, the seemingly unexplainable events that occur, and the strategy used during drilling. Thrust levels during drilling range from 600 to 2,500 pounds. Hydraulic motors powered by a 30-hp, 440-volt motor provide ample power for drilling horizontal holes 2,000 feet long.

Jan 1, 1975

By R. E. Head

At the microscopic laboratory of the Bureau of Mines Intermountain Experiment Station, Salt Lake City, Utah, efforts are being made to devise methods of differentially coloring finely crashed minerals as a means for their identification. Staining would facilitate sight recognition of minerals under the microscope and would be of great value in the study of crushed ores, concentrates, and tailings. Since the treatment of ores for their beneficiation is primarily based on the recovery of the minerals containing the clements of value, it is extremely important that these minerals should be known and that a method for quickly determining them when in minute fragments should be available. Herein lies one of the greatest uses for color methods. In many cases it is a difficult matter for even the trained petrographer and mineralogist to identify finely crushed minerals quickly. Although ordinary petrographic methods are accurate, they are often time--consuming and are not suitable to the needs of millmen who require, especially in the examination of tailings a method for determining minerals by inspection.

Jan 1, 1929