Search Documents

By W. H. Engelmann

The electrokinetic (zeta) potentials of a charcoal granite in an aluminum chloride (AlCl3) solution and in an oleylanunonium acetate (C18H35NH3+ -OCOCH3) solution have been correlated with the specific damping values as measured by the pendulum sclerometer. This investigation shows that the pendulum specific damping attains a minimum at the isoelectric point for the charcoal granite-aluminum chloride and charcoal granite-oleylammonium acetate systems, and thus indicates that the penetration of the diamond points is a maximum at the isoelectric point.

Jan 1, 1967

By James J. Jessop, Richard E. Thill, Michael J. Friedel

As part of an investigation aimed at improving the health and safety and competitiveness of the mining industry, the U.S. Bureau of Mines evaluated the application of common offset radar profiling, using a 250-MHz ground-penetrating radar (GPR) system, for the detection of fractures in igneous rock. A series of radar reflection surveys were conducted to detect and delineate the extent of fracturing at various granodiorite and gabbro quarries and outcrops located in Minnesota. The application of radar profiling for detecting joints, sheeting fractures, shear zones, and depth to water table was demonstrated to be feasible with minimal processing. Radar reflection interpretations were verified by visual inspection of the rock mass and field mapping of local structure. The radar reflection section provides a simple, rapid, and cost-effective means for mapping of shallow (less than 10 m) small-scale fractures (greater than 0.25 cm) in igneous rock masses (characteristic of velocities between 0.061 m/ns for gabbro and 0.125 m/ns for granodiorite). Depth or distance estimates to fractures are within 10 pct of the actual, and time-shift compensation is necessary only when topographic irregularities exceed 30 cm.

Jan 1, 1992

By J. P. McGee

A 1,000-hour test with a gas turbine at 1,200° F showed a working fluid of 1 gr of ash per 100 scf of power gas (79 percent of the ash 7 to 35 microns in diameter) to be excessive for acceptable blade wear for commercial practicability. Blades in the turbine consisted of about 20 percent each of chromium, cobalt, and nickel; 3 percent molybdenum; 2-1/2 percent tungsten; and smaller amounts of manganese, columbium, and tantalum. Erosion of both the fronts and backs of the turbine nozzles was particularly heavy, the trailing edges being worn to a featheredge. Erosion of the buckets was less marked, although the leading edges were somewhat pitted. A refractory-lined combustor performed efficiently and with little abrasion of the lining by the ash-laden gas.

Jan 1, 1969

To reduce equipment operator exposure to respirable dust in enclosed cabs by examining the effectiveness of retrofitting air pressurization and filtration systems on existing cabs.

Jan 1, 2001

By R. H. Grau, S. B. Robertson, F. Garcia, A. C. Smith, T. P. Mucho

Researchers working for the National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Center are developing ways to protect the health of miners. Part of that effort is improving the air quality in metal/nonmetal mines by developing proper ventilation techniques. The air quality of large opening nonmetal mines can be greatly improved by using engineering controls of contaminant prevention and proper ventilation techniques. Contaminant prevention includes methods to reduce contaminants from entering the mine air. Ventilation can be improved with appropriate fan selection and fan operation used in conjunction with air coursing using manmade and insitu rock stoppings.

By N. S. Dalal, B. Jafari, V. Vallyathan

Electron spin resonance measurements have now been completed on the decay kinetics of the organic free radicals formed on crushing or grinding of a well characterized anthracite coal. The free radicals exhibit a complex decay pattern for the first few hours after the grinding, and a smooth decay thereafter. Parallel hemolysis studies indicate. a half-life of the decrease in the cytotoxicity of the fresh· dust to be about half-a-day. The cytotoxicity of the freshly-made dust decreases on addition of superoxide dismutase, catalase and sodium benzoate. The hemolysis rate is lower for the dust stored in buffers as compared to air. A chemical model will be presented to accomodate the cytotoxicity and spectroscopic data, and ~heir implicati6ns to pneumoconiosis.

Jan 1, 1988

By Liming Yuan

A computational fluid dynamics (CFD) study was conducted to model effects of coal properties on the potential for spontaneous heating in longwall gob (mined out) areas. A two longwall panel district using a bleeder ventilation system was simulated. The permeability and porosity profiles for the longwall gob were generated from a geotechnical model and were used as inputs for the three dimensional CFD modeling. The spontaneous heating is modeled as the low temperature oxidation of coal in the gob using kinetic data obtained from previous laboratory scale spontaneous combustion studies. Heat generated from coal oxidation is dissipated by convection and conduction, while oxygen and oxidation products are transported by convection and diffusion. Unsteady state simulations were conducted for three different US coals and simulation results were compared with some available test results. The effects of coal surface area and heat of reaction on the spontaneous heating process were also examined.

Jan 1, 2008

By B. J. Dalton

The Bureau of Mines Helium Research Center has as a long-range objective the development of an equation of state for helium that will allow all of the thermodynamic properties to be calculated within the accuracy with which they are known. If this objective is to be realized, a method of calculation must be known. This report gives the principles of the method we use in such problems. A computer program was developed for predicting these properties, including those at the critical point, that is perfectly general and applicable to any equation of state. To demonstrate the efficacy of our method, this computer program was used to evaluate thermodynamic properties of a Redlich-Kwong fluid in the two-phase region. Expressions for calculating various thermodynamic functions specific for this particular equation of state are derived. Numerical values are tabulated and graphs are presented for all functions calculated. It is shown that for a Redlich-Kwong fluid there are finite discontinuities in (1) the second temperature derivative of the Gibbs free energy or chemical potential at the critical point, (2) the second derivative of the vapor pressure curve with regard to the temperature on passing through the critical point, and (3) the measured heat capacity at constant volume on passing through the critical temperature when the calorimeter is filled to the critical density. It is also shown that the heat of vaporization is infinite for a Redlich-Kwong fluid at absolute zero.

Jan 1, 1969

By Jack I. Paige

In this Bureau of Mines study, two fluidized-bed reactors were designed, built, and operated, one as a sorber for S02 and the other as a contactor for the regeneration of the sulfur-laden alkalized alumina. The target of 90 percent removal of S02 from a flue gas stream containing 0.3 percent S02 was attained by using a sorbent feed of 10-15 grams per minute into a 5-inch bed depth of alkalized alumina. The sorption unit was operated at about 330° C. Complete regeneration of the laden alkalized alumina containing 5 to 10 percent sulfur was accomplished in approximately 1/2 hour. An excess of reformed propane at about 730° C was the regenerating gas. Attrition losses, a major problem with this sorbent, ranged from 0.9 to 7.9 percent of the inventory. Data from these tests demonstrate, within experimental error, the validity of equations developed from short-term, thin-bed tests related to sorption and regeneration rates.

Jan 1, 1970

By C. Gary Reiness

A safety glass eyepiece which had been repeatedly exposed to mine environment over a number of years was studied to determine some of its optical properties. In the regions from 385 to 400 mµ and from 625 to 760 mµ, the transmittance was less than the 89 percent required by the American Standard Safety Code for Head, Eye, and Respiratory Protection. From 200 to 320 mµ the relative transmittance of two parts of the eyepiece was found to vary widely, having a maximum of 38 percent difference at 315 mµ. Irradiation of the glass by ultraviolet light caused enhanced absorption in the range from 200 to 1,200 mµ. There was a time-dependent increase of 1016 color centers per cubic centimeter throughout this range after 36.5 hours of irradiation. The rate-of-growth curve for the optical density, at 243.5 mµ and 23° C, was resolved into linear and saturable components, indicating zero order and first order

Jan 1, 1968

By H. B. Carroll

The Bureau of Mines investigated the adaptability of the Meteorology Research Inc.2 (MRI) nephelometer and the Sinclair-Phoenix smoke meter for use in routine, analytical, smog-chamber experiments and to compare their responses to aerosol during these experiments. Both instruments' sampling systems were modified--smaller size sample input systems were studied using the nephelometer and a secondary sample system was added to the smoke meter to allow measurement of Aitken or condensate nuclei. Both instruments were easily adapted for use with small smog chambers and both displayed good precision and sensitivity to aerosol. A correlation was shown to exist between the two instruments' responses to aerosol. This correlation makes it possible to report the Sinclair-Phoenix measurements in visibility and/or mass units if desired.

Jan 1, 1973

By W. A. Young

To initiate this project a critical evaluation of the pre-sent phosphate mining industry in the Western phosphate field was conducted. Mines were visited, mine operators were interviewed and pertinent literature studied. Three phosphate mining enterprises were reviewed and mining cost estimates prepared. The report discusses the present state of phosphate processing, rock alteration and location. New ideas and concepts are proposed to improve the recovery of phosphate rock from the Phosphoria formation. The report evaluates two variations to the present phosphate open pit mining methods, which were developed to improve the economics of mining phosphate and to better accomplish necessary reclamation and accelerate the time for environmental recovery. A material handling system using conveyor haulage will eliminate the need for trucks. Terrace haulback utilizes safety benches to haul and dispose of waste in the mined out pit. Ore will be removed from the pit via an inclined, cable-supported mobile conveyor.

Jan 1, 1980

By Richard J. Mainiero

The Bureau of Mines investigated coal-mine-type short-delay electric detonators marketed by three domestic manufacturers to determine the accuracy of delays and the probability of overlap between adjacent de- lay periods. The Winzer index was computed and compared with the probability of overlap. A close agreement between the Winzer criterion and overlap probability was demonstrated. A permissible blasting unit capable of delivering a maximum firing energy of 4.0 J and a digital oscilloscope were used to measure the delay time with an accuracy of 20.25 ms. Another oscilloscope and a pulse transformer were used to record firing current. Experimental data indicated negligible overlap probability in detonators of shorter delay periods: periods 1 to 4, which correspond to 25 to 250 ms. However, a significant probability of overlap was detected in some detonators of longer delay periods: periods 5 to 9, which cor- respond to 300 to 500 ms.

Jan 1, 1985

By C. A. Komar

Laboratory-scale hydraulic fracture tests were conducted by the Bureau of Mines on directionally oriented sandstone material, along with measurements of directional rock properties such as tensile strength, permeability, ultrasonic velocity, and dynamic elastic constants. In these tests, fracture orientation was determined as a function of various combinations of stress, rock saturation, rate of borehole pressurization, and direction of minimum tensile strength relative to minimum horizontal compressive stress. The objective of the experiment was to investigate whether horizontal stresses always controlled the orientation of induced vertical hydraulic fractures, or if under conditions of small differences in stress and/or slow borehole pressurization rates, the induced fracture direction was influenced by directional properties of the rock matrix. This study shows that the expected influence of horizontal earth stress on the orientation of an induced hydraulic fracture becomes negligible when¬ever the magnitude of the difference between the compressive stresses is 200 psi or less. When this occurs, fracture orientation is controlled by the directional properties of the rock--primarily permeability and tensile strength.

Jan 1, 1973

By Peter F. Steidl

Seven degasification wells have been completed in the Pittsburgh coalbed at the new Emerald mine near Waynesburg, Pa. Funding was provided by the Bureau of Mines to perform stimulation treatments on five of the wells, to show that this is a feasible and economical means of degasifying part of a coalbed. The seven wells ranged in depth from 590 to 910 feet. Stimulation treatments used 25,260 to 42,660 gallons of foam and 7,400 to 12,800 pounds of 20/40-mesh prop sand. Pumping rates were 10.8 to 11.6 bbl/min and treating pressures were from 1,050 to 1,600 psig. On the day following stimulation, gas production ranged from a few hundred cubic feet per day to more than 100,000 cu ft/day.

Jan 1, 1978

Table 1.-Employment and injury experience at metal mines in the United States, by industry groups [ ]

Jan 1, 1967

By Stephen C. Tadolini, Thomas M. Barczak

An underground investigation was designed and implemented by the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of pre-driven longwall recovery rooms supported with pumpable concrete roof supports. The pumpable roof supports were instrumented with hydraulic pressure cells to measure support loading. Displacement of the support was also measured to assess the support reaction to ground movements. Movement up to 12.5 m (40 ft) into the roof was measured with sonic probes and multipoint extensometers. Borehole pressure cells were installed in the panel fender and outby pillars to evaluate load transfer. Shield loading was also assessed to determine the impact of the panel fender yielding on face loading. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 3.12 m (10 ft) from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 15-20 cm (6-8 inches) once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 10 m (32 ft) horizon with total deformation ranging from five to 10 cm (2 to 4 inches), indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in instabilities that can lead to catastrophic results. Understanding the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields is providing valuable information for the refinement of the NIOSH Ground Reaction Curve for standing and intrinsic roof support system design.

By Wilbur I. Duvall

This report presents experimental data on the propagation of explosion- generated strain pulses in rock. Tests were performed in 5 different rock types, employing 10 different types of explosives. Charge sizes ranged from 0.5 to 50 pounds, and travel distances ranged from 2.5 to 70 feet. Analysis of the data shows that the experimental peak strain data satisfy an exponential decay propagation law of the form: ?R/W1/3 = Ke ?aR/W1/3. For a particular rock, parameter K is a linear function of the calculated detonation pressure or the calculated energy density of the explosive. For a particular explosive, K is a linear function of the elastic parameter of the rock, p2, a result, which is at variance with elastic theory. The absorption constant, a, is independent of type of explosive but dependent upon rock type. However, no definite relation between a and the physical properties of the rock could be established.

Jan 1, 1959

By Donald P. Blasko

The Bureau of Mines investigated two areas of the Alaska Peninsula (Iniskin Peninsula and Becharof Lake) where oil and gas seeps were known to occur in an attempt to determine (1) whether the seeps are still active and (2) the amount of bitumen contained in the drainage leaving the seeps. The oil, water, oil-water, and gas were sampled and analyzed. Five oil samples were taken at four separate oil seeps. The API gravity of the oil ranged from 8.90 to 21.4° and the sulfur content was from 0.12 percent to 0.59 percent. Four of the seven gas samples obtained revealed fair high caloric values, ranging from 746 to 924 Btu/cu ft, and averaging 844 Btu/cu ft. A total of 44 water samples were obtained. Bitumen content of the water was as high as 9,773 mg/l at one seep, but averaged less than I mg/l where the seep-drainage water entered the Gulf of Alaska.

Jan 1, 1976

By F. J. Smith, W. A. Gallagher, C. A. Herbert

"INTRODUCTION A fire started about 10 a.m., November 10, 1947, at the Kings mine, Princeton Mining Co., Princeton, Ind., about 1,800 feet inby the main shaft bottom on the main west haulage road at a point estimated to be 2 miles from the faces of the main west entries. No lives were lost, as 27 men escaped from the mine after a series of explosions, which necessitated sealing the mine on the surface. This information circular shows"" how adverse conditions might be overcome, when reopening a sealed mine, by expert planning and close cooperation on the part of various organizations. Conditions found in the mine after it was reopened were comparable to the worst that had been anticipated, yet the mine was recovered with comparatively little difficulty and a minimum of risk. The open workings in the mine covered a vast area, but most of the mine resumed production of coal after being sealed for only 37 days.The information contained herein also points to the desirability of adhering as closely as possible to a predetermined schedule of operations."

Feb 1, 1949