Search Documents

By H. F. Coward, G. W. Jones

"IntroductionIn the course of an investigation on the influence of black damp (a mix of nitrogen and carbon dioxide) on the limits of inflammability of fire damp (methane) in air, some new information was obtained concerning the factors that determine whether or not a gas mixture is capable of self-propagation of flame. Volume for volume, carbon dioxide exceeds nitrogen in its extinctive action on flame, an effect which is generally attributed to the higher molecular heat capacity of the former. Argon, a as of lesser heat capacity than either, proved to Lave less extinctive notion. If, as seemed likely, the extinctive action of a chemically inert gas could be attributed entirely to its heat capacity, then helium should behave like argon; equal volumes of these two oases should exhibit equal extinctive action, for their molecular heat capacities are nearly identical at laboratory temperatures and, in all probability, remain constant up to and beyond flame temperatures. The experiments reported here show, however, that helium has proved to be more extinctive of methane flames than argon.Method Used in ExperimentsThe limits of inflammability of methane, in various ""atmospheres"" composed of mixture of air with one or other of the diluent were determined in a vertical glass tube, 6 feet long and 2 inches in diameter. The lower end of the tube was opened by sliding away a ground-glass joint and the flame of a small spirit lamp was immediately passed across the aperture. The tube was sufficiently long to enable observers to judge whether a flame was self-propagation for if a mixture were incapable of continued self-propagation pf flame, the lamp of flame formel above the source of ignition was extinguished within feet of its passage up the tube."

Jun 1, 1926

By R. C. Anderberg, F. J. Caervenyak, F. J. Frattali, H. J. Kandiner, R. A. Brown

"INTRODUCTION Considerable interest was shown .prior to and during World War II in the winning of metallurgical-grade alumina from anorthosite, kaolin, siliceous bauxites, diasporic clays, and other aluminum-bearing ores. Laboratory and pilot-plant investigations were made on many of these ores by the Bureau of Mines, and a series of reports on them is being prepared. This report covers the tests made on the application of the lime-soda-sinter process to anorthosite, which is a mixture of albite, NaAlS1308, and anorthite, CaAl2Si208. Extensive deposits of anorthosite occur in the Laramie Range in Wyoming and extend into Colorado; other deposits are found in New York, with outcroppings appearing in Vermont, Maine, and Labrador.Anorthosito can not be treated by the Bayer process for the production of metallurgical-grade alumina, because excessive losses of soda and alumina occur from the formation of sodium-aluminum silicate due to the large amount (50 percent) of silica in the ore.RESULTS OF INVESTIGATIONSSmall-scale laboratory tests supplemented by pilot-plant runs have demonstrated that the alunina and soda occurring in the Wyoming anorthosite from the Laramie Range can be extracted and recovered satisfactorily by the lime-soda process. It has been shown that liquors containing approximately 95 gram of A1203 per liter can be consistently produced at Na20:A1203 ratios from 1.75 to 2.27, and that these liquors can readily be desilicated and carbonated to yield high-grade alumina trihydrate of quality comparable to that essential for cell-grade alumina. The optimum results were obtained with Na20:A1203 mol ratio of 1.03 and Ca0:Si02 ratio of 2.14 in the sinter when calcined at an average temperature of 2,444ºF. for 25 minutes."

Nov 1, 1947

By Frank A. Peters

This Bureau of Mines report is the second of a series of process evaluations planned to determine the relative processing costs of producing metallurgical-grade alumina from low-grade aluminous materials. Included in these evaluations are recommendations for additional research and development to improve the processes and to lower their costs. The design for each process is based on published work. The processes considered in this report are designed to extract alumina as aluminum chloride from calcined clay with 20 percent hydrochloric acid and to remove the silica residue by filtration. Iron is removed by one of the following processes: Isopropyl ether extraction, in which iron chloride is extracted before decomposing the aluminum chloride; gas precipitation, in which the aluminum chloride is precipitated with hydrogen chloride while leaving the iron chloride in solution; gas precipitation-isopropyl ether extraction, in which the aluminum chloride from precipitation is extracted with isopropyl ether, if necessary; caustic purification, in which a crude alumina is produced and then purified by a modified Bayer operation; or sinter purification, in which a crude alumina is produced and then purified by a lime-soda sinter operation. For plants producing 1,000 tons of alumina a day the estimated operating costs per ton of alumina are: [Isopropyl ether extraction process $ 65.09 Gas precipitation process 89.04 Gas precipitation-isopropyl ether extraction process 119.65 Caustic purification process 73.79 Sinter purification process 80.47] The estimated fixed capital costs per annual ton for these plants on a Marshall and Stevens chemical equipment basis of 240.0 are: [Isopropyl ether extraction process $229.03 Gas precipitation process 287.16 Gas precipitation-isopropyl ether extraction process 356.59 Caustic purification process 266.48 Sinter purification process 279.13]

Jan 1, 1962

By James J. Olson

The Bureau of Mines recorded and analyzed overpressure levels for three production blasts at the White Pine copper mine, Upper Michigan, to obtain representative data from single-heading blasts in a long, straight haulageway and to estimate the damage potential inherent in production blasts fired in close proximity to underground structures. Commercial pressure gages with a flat response to 1 kHz were used with an FM tape recorder to record the overpressures from one dynamite and two AN-FO (ammonium nitrate-fuel oil), 500-msec production blasts having zero-delay charge weights of about 75 lb (34 kg). The recorded waveforms from the underground blasts (1) were more complex than the typical free-air wave, (2) were of longer duration, and (3) had numerous secondary arrivals due to reflections from the ribs and roof. The waveforms showed that the zero-delay charges produced the only high overpressures. First pulse peak overpressures from the blasts ranged from 0.10 lb/in2 (6.9 X 102 N/m2) at a distance of 471.1 ft (144 m) to a maximum of 1.76 lb/in2 (121.3 X 102 N/m2) at 191,7 ft (58.4m) from the blasts. An analysis of variance of the first pulse overpressures from the three White Pine blasts showed that no statistically significant difference existed among the overpressure levels from the dynamite and AN-FO blasts and that a single equation P = 4.9 x 103 (D /W1 / 3) 2 .15, where P = overpressure in pounds/inch2, D = d-stance from the blast in feet, and W = zero-delay charge weight in pounds, could be used to describe the falloff of overpressure with distance.

Jan 1, 1971

By H. L. Gibbs

A portable radon monitoring instrument capable of making on-the-spot measurements of the radon gas content of uranium mine atmospheres was designed and constructed. The monitor was tested in the laboratory and in operating uranium mines. Good correlation was obtained between the monitor readings and radon measurements made on mine atmosphere samples taken in radon bottles.

Jan 1, 1973

By Richard G. Burdick

This Bureau of Hines report describes an interface between a minicomputer and peripheral device, The logic used to develop the device is discussed briefly, after which the device is described in detail; complete construction and operational details are given. The report should aid both in duplicating this device and in designing similar devices for different uses.

Jan 1, 1975

By A. J. Kraemer

[A great deal of interest has been manifested in the question of sulphur in fuels for automobile engines. Many different opinions have been expressed with respect to the effect of sulphur in gasoline on engine wear and engine performance. A wide difference of opinion exists as to the permissible limit of sulphur content for satisfactory operation.]

Jan 1, 1927

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

A computer program has been developed to simulate evacuation of a mine in case of fire in the following, the capabilities, operations and structure of the program are described with illustrative examples to demonstrate usefulness of using the program. A detailed description of the program with sufficient information to make use of the program appears in Appendix B.

Jan 1, 1976

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

B 2 Program Use Instructions necessary to execute the program, after the card deck has been prepared, are summarized in the following. B 2. 1 Input Data Format Input data is supplied to the program in two ways a. By data cards that are read in after program compilation. b. By data specifications that are included within the program.

Jan 1, 1976

By D. Harrington, C. W. Owings

"The belief is now fairly general among the coal-mining people of the United States that one of the most effective methods of preventing wide-spread coalmine .explosions is that of introducing rock-dust into coal mines to reduce the inflammability or explosibility of dusts found on mine surfaces. Notwithstanding this belief it is improbable that even a small fraction of 1 per cent of the coal mines of the United States are at all adequately protected by rock-dust; in a survey made in the summer, and fall of 1927 it was found that but 463 out of more than 7,000 operating bituminous and lignitic coal mines were using rock-dust at all, and that few if any of the 463 were fully or adequately protected by rock-dusting.Inspections of a large number of mines through the United States by Bureau of Mines safety division field men have failed to reveal a single adequately rock-dusted mine, Yet there is no doubt that many of the owners and operators believed their properties to be fully protected by rock-dust against the much-feared hazard of widespread explosion. Two of the most disastrous explosions of recent years occurred at properties where the owners were definitely of the belief that the rock-dusting done had made the mines immune to widespread explosion involving coal-dust. In both instances it was found that although some rock-dusting had been done, the mines were more nearly 1 per cent than 100 per cent rock-dusted.This condition as to inefficiency or insufficiency of rock-dusting in the coal mines of the United States is almost universal, and unless our mining men awaken to its, dangers, the disaster record of the coal-mining industry is much more likely to become worse than better. During the fiscal year ended June 30, 1928, the attention of the safety division of the United States Bureau of Mines was called to. 22 explosions With 320 fatalities in bituminous coal mines of the United States; and of the 22 explosions there were 10 with 258 fatalities in mines that were listed as having used rock-dust; upon investigation it was found that as usual the rock-dusting had been anything but comprehensive or adequate. It is probable that in a very few instances last year the relatively small amount of rock-dusting stopped the .extension of the explosion and thus prevented further expansion of the death list. In general, however, the explosions occurred in a part of the mine that had not been rock-dusted - and right here is the crux of the failure or probable failure of present-day rock-dusting in the United States, There should be no part of any bituminous or coal mine in which all of the exposed surfaces (roof, ribs, and floor) have not been thoroughly rock-dusted and kept thoroughly rock-dusted. In other words, all exposed surfaces of all accessible places in bituminous and lignitic coal mines should be kept covered with rock-dust so that the combined rock-dust coal-dust mixture at all times and in all places has less than 35 or 40 per cent combustible matter, The only exception to this rule is that surfaces which are wet (and this does not mean merely damp) need not be rock-dusted. However, a mine opening may have several inches of water on the floor and yet have much explosive dust on the ribs and roof above the water; in such places the ribs and roof should be kept rock-dusted, irrespective of the wetness of the floor."

Nov 1, 1928

By A. Wahab Khair, N. P. Reddy

"Abstract. This paper attempts to characterize coal breakage due to the action of a continuous miner. Coal blocks with an approximate dimension of 45.7 cm x 38.1 cm x 15.2 cm (18 in. x 15 in. x 6 in.) were first subjected to confining pressures equivalent to in-situ conditions. Then the blocks were cut along the face/butt cleat direction by the cutting head of a specially designed unique automated rotary coal cutting simulator (ARCCS), simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-sit and operating parameters a number of other para¬meters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment, the coal fragments were collected in bags using a vacuum cleaner. These fragments were then sieved for size distribution analysis.INTRODUCTIONThe Federal Coal Mine Health and Safety Act of 1969 was enacted to emphasize to coal operators that the airborne respirable dust should not exceed 2 mg/m3, thus reducing the incidence of coal workers pneumoconiosis.Dust control techniques such as conventional water sprays and dust collectors are only partially effective and require additional equipment expenditures. A more authentic approach would be to reduce respirable dust at the source the continuous mining machine cutting head, where the fragmentation process occurs. Improving the fragmentation process by characterizing the coal breakage will not only reduce respirable dust at the face, but it will also decrease the amount of respirable dust that is liberated during the secondary handling.Fragmentation of coal can be expressed as a function of three major groups of parameters; namely, 1) coal properties, 2) in-situ conditions and 3) operating parameters. This paper deals with the characterization of coal breakage along both face/butt cleat direction as a function of machine operating parameters such as rate of advance, angle of attack, bit configuration, bit lacing (spacing and pattern) and bit speed at various equivalent in-situ pressures."

Mar 1, 1989

By H. P. Greenwald, G. E. McElrey

"Part IV.- The Resistance Caused by Right-Angle Bends. IntroductionThis paper deals with the fourth phase of an extensive research on coal-mine ventilation factors. A comprehensive report of the entire work is in course of preparation, but abstracts of the various chapters are being prepared in order to make the major results public as rapidly as possible. Parts I, II and III were issued as Serials Nos. 2621 (July 1924), 2647 (October 1904) and 2671 (March 1925) and dealt with the resistance of unobstructed entries, the resistance due to mine cars and, the resistance of timbered entries respectively.Description of the Tests With the last cutthrough between the two butt entries of the test section in the Experimental Mine open, the air flow was deflected, around two right-angle bends in the same direction, the butt entries being 50 feet center to center and approximately 6 by 9 feet in cross section. Each bend had a dead end opening off of it; that at the first bend was in the direction of flow and that at the second bond was at right angles to the flow. For a primary test condition the inner corner of each bend was trimmed square and the dead ends were closed off with board brattices set flush with the line of the cut-through.The two corners of the first band were, then modified both independently and in conjunction. Various modifications of both bends in conjunction were also tested with rather surprising results as to the effect of conditions at the first bend, upon the pressure losses at the second. To confirm the theory developed to fit these results a series of tests were made to give a direct comparison of the -pressure losses as between two bends with the air flow deflected in the some direction at each and with the air flow deflected in opposite directions. The former is designated ""double"" and the latter a ""reversed"" right-angle bend. This series of tests was conducted, however, on the bends at one of the intermediate cutthroughs at which the flow could be deflected us either direction at the second, bend. Here also the average cross-section was 6 by 9 feet and the bends were 50 feet apart."

Jan 1, 1928

By Will H. Coghill, F. D. DeVaney

"Many of the iron ore deposits on the western end of the Mesabi Range Minnesota consist of the so-called ''wash ores."" Because of their high silica content these ores must be washed or concentrated to make them merchantable. Washing plants have been in operation for 20 years, during this period large quantities of tailings have accumulated in tailings ponds. These tailings contain the aggregate millions of tons of iron oxides which, if recovered, would greatly to the available tonnages and to the revenues of the mining companies. It the purpose of this paper to outline give results of concentration tests on tailings.In order that the reader may understand more clearly the type of material under consideration, a short description of the characteristics of the wash ores of the Western Mesabi Range and a brief resume a washing methods that have been are now being employed will be given. Appleby and Newton4 In their description of the district and of the ores say:The Western Mesabi district embraces the territory west of the town of Nashwauk in Itasca County. The territory to the east of this dividing line is known as the Central and Eastern Mesabi district. This subdivision is rot wholly arbitrary. While the ore bodies in the two districts resemble each other in. shape, size, and general structure, there is a marked and very important difference in the character of the respective ores. For purposes of comparison, the western deposits have been called washable ore bodies, and the central and eastern, standard ore bodies. The latter ores are the result of natural concentration processes which have teen carried far enough to produce a large proportion of high-grade ore Wet can be marketed direct; the Western Mesabi ores present a lesser degree of natural concentration and are as a rule of too low grade to admit of marketing without preliminary treatment. In many cases the grade can be improved by washing, hence the material is called washable ore. Exceptions to thin general rule may be noted in both districts. Many of the Western Mesabi ore bodies contain quite a proportion of merchantable ore. There are also portions of central and eastern Mesabi ore deposits which are of low grade and which can be improved by washing."

Nov 1, 1930

By Paul R. Thimas, Edward H. Boyle

"The Bureau of Mines evaluated the long-term cost and availability of primary gold production from 135 mines and deposits worldwide. Collectively, the evaluated countries represent 93 pct of world gold production. Total recoverable gold available (as of January 1984) from a subset of 111 significant producing mines and developing deposits in 13 market economy countries (MEC's) is estimated at 810 million tr oz. The Republic of South Africa is estimated to account for 87 pct of total recoverable gold. The United States and Canada account for 4 and 4.5 pct of the total, respectively. Eighty-three percent of total recoverable gold is available at a constant 1984 break-even price of $400/tr oz, and 70 pct is available at $300/tr oz. South Africa accounts for 90 pct of the gold available at $400/tr oz or less.Major conclusions are that (1) South Africa should remain the largest world producer through the year 2000, (2) annual MEC output in 2000 should not be significantly different than current output given constant 1984 gold prices of more than $300/tr oz, and (3) there may be a significant decline in production after 2010 in the absence of major new discoveries and continued development of new mines to offset the depletion of the South African mines. INTRODUCTIONSince the late 1970's the world gold mining industry has been characterized by dynamic growth in production and volatility in price. World production in 1983 was almost 15 pct greater than in 1980, and the short-term trend continues upward. Annual dollar-based price changes since the early 1970's have been unprecedented in both magnitude and volatility. This commodity, which sold for $35/tr oz3 for over a third of a century, reached an annual average $612/tr oz in 1980. Until 1980, the future price of gold seemed set on an upward trend. Since that year, however, world gold prices have fallen by over 50 pct to slightly over $300/tr oz at the end of 1984.Against this background, this study was undertaken to determine (1) the level of world demonstrated gold resources, (2) total and annual availability of gold mine production, (3) long-run production costs per operation and by national aggregates, (4) the economic and technical factors that impact upon cost and availability, and (5) probable future mine production and cost trends."

Jan 1, 1985

By Bruce Pinkston

This report presents a description of the Prototype Demonstration Vehicle and Safety Guidelines developed under U.S. Bureau of Mines Contract No. JO 366003, ?Improving Man Transit Safety. This vehicle was constructed to assess the feasibility of a set of equipment related guidelines which were drafted in Phase I of the same contract. State-of-the-Art improvements are embodied in such areas as collision survivability, occupant comfort, and multiple mode (on and off rail) operation. The electric battery powered vehicle carries a twelve man section crew at speeds up to 12 mph. The description of the demonstration vehicle Is presented In Volume I. Safety Guidelines are presented in Volume II.

Jan 1, 1981

By Perry N. Halstead

This report describes two goniometers that, by simple manipulation, can be used to ascertain the attitude of a joint, vein, or fracture plane observed on the planar projection of a borehole photograph taken with an NX borehole camera of the type developed by the U.S. Army Corps of Engineers. One goniometer was designed to interpret photographs taken in vertical drill holes and the other for photographs taken in inclined drill holes. In practice, several measurements are made on each photograph with the goniometer. These data are then substituted into mathematical equations, which are derived in this report and the attitudes of fracture planes are determined.

Jan 1, 1968

By A. B. Hooker

The flame safety lamp with metal-gauze enclosure was invented by Sir Humphrey Davy more than a century ago, primarily for its safe light; however, it soon became the standard device for detecting the presence of methane in mine atmospheres. It still is the most widely used device for this purpose and is also the most practicable means of detecting deficiency of oxygen in coal mines. A permissible flame safety lamp is similar in all respects to one that, after a series of tests, has been approved by the Bureau of Mines as safe for use in gassy mines. However, safety depends largely upon the way lamps are maintained and used.

Jan 1, 1944

By Mark Sheppard

This p aver is the second of a series recording the results of tests made at various quarries throughout the United States to determine, (1) the relation between the size gradation of feed to, and product from, primary crushers; (2) the particle shape of crushed product; (3) the differences in gradation and particle shape produced by different types of primary crushers; and (4) the differences in gradation and particle shape caused by crushing different kinds of stone. Primary crushing has received comparatively little attention in the technical literature in spite of the fact that the design of the whole crushing plant should be correlated to the performance of the primary crusher.

Jan 1, 1938

By Mark Sheppard

This paper is the second of a series recording the results of tests made at various quarries throughout the United States to determine, (1) the relation between the size gradation of feed to, and product from, primary crushers; (2) the particle shape of crushed product; (3) the differences in gradation and particle shape produced by different tries of primary crushers; and ( 4) the differences in gradation and particle shape caused by crushing different kinds of stone. Primary crushing has received comparatively little attention in the technical literature in spite of tine fact that the design of the whole crushing plant should be correlated to the performance of the primary crusher.

Jan 1, 1938

By Fred L. Bishop

This paper describing the methods employed in the purchasing and supply departments of the Miami Copper Co., Miami, Ariz., is one of a series being prepared for and published by the United States Bureau of Mines on office practice in mining operations. GENERAL DESCRIPTION The Miami Copper Co.'s plant is located about 1 mile from the town of Miami, in the Globe-Miami Mining District, Gila County, Ariz. The property consists of a complete mining plant, concentrator, high-pressure steam power plant, and many other attendant structures. In normal times the company employs about 1,500 men, and mines and mills about 6,000,000 tons of ore annually.

Jan 1, 1932