Search Documents

By Edward D. Thimons

The Bureau of Mines developed a stopping design that allows the stopping to be blown down by strong blast forces without incurring any permanent damage. Trials with the new stopping, dubbed the quick-fix blowout stopping, have been conducted in the Bureau's Safety Research Coal Mine at Bruceton, Pa., and in two New Mexico uranium mines. Results have been favorable in all cases. Compared with conventional brattice stoppings or wood bulkheads, the quick-fix blowout stopping is easier and less time consuming to install, is easier to maintain, and in most cases is just as efficient an air barrier. There is same indication that the shape of the stopping makes it more resistant to blast fore s than the fabric stoppings now in use.

Jan 1, 1976

By T. Whitrnoyer, J. Sneckenberger

"The acOustic impedances of seven rat lungs were measured at frequencies between 100 and 6400 Hz. Rats were divided into two groups: a silica exposed group (N=3) and a control group (N=4). The silica exposed group was injected intratracheally with silica solution. Three of the control group were intratracheallyinjected with saline. Between four and six weeks after theinjections, all lungs were excised and degassed. Lungs were,suspended in a pressure Chamber, with the trachea canula attached to the end Of a tapered impedance tube. The lungs were subjected to transpulmonary pressures between -30 cm H2O and 6 cm H2O to simulate deflation and inflation. With transpulmonary pressure being held constant, the impedance tube was excited with random noise. A dual channel analyzer calculated H12(f), the transfer function between the two microphones. This function was used to calculate the lung's impedance at that pressure. The impedance magnitude spectra of both groups typically had peaks at 2000,3500, and 5500 Hz. Statistically significant differences. (90%confidence level or greater) between the two groups occur at the 3500 Hz peak at transpulmonary pressures of 20, 8, 6, 4, and 2 cm of H2O. This fact seems to confirm that this method can detect. lung disease. Further research will indicate whether this method will be able to detect the onset Of coal worker's pneumoconiosis.INTRODUCTIONOne of the first studies of impedance Of the human lung were conducted by DuBois et al.[2] using the forced OscillatiOn technique. This technique, however, was limited to frequencies below 30 Hz. Further studies by Van Den Berg [6] revealed thatthe lung reflected higher frequency sounds (100-10,000 Hz), instead Of behaving as an anechoic termination. This discovery has lead to several studies of the acoustical properties of both human and animal lungs at high frequencies [3,4,5]."

Jan 1, 1988

By James Paone

This report shows the feasibility of predicting drillability, analytically, by using regression analysis techniques. The approach is new in diamond-drilling research. Further, the study shows that this technique may be of value to drill manufacturers and others in mathematically delineating performance characteristics of new drills in specific rock types. Another application might be the prediction of penetration speeds in extraterrestrial material based on the physical properties of the materials as samples become available. Prediction equations for penetration rates are presented for 9 rocks drilled in the laboratory and for 20 rocks drilled under field conditions. The prediction equations are based on drill operating parameters and on characteristics of the rock penetrated. No single physical property appeared consistently in the best predictor equations, and all the physical properties were found to be highly correlated with each other.

Jan 1, 1966

By H. P. LeVan

Research was conducted to examine the feasibility of extracting manganese from Georgia umber ore by a three-stage continuous sulfuric acid-ferrous sulfate pickle liquor leaching process. A continuous cyclic process for treating the umber was operated successfully, using a synthetic solution simulating a ferrous sulfate fortified anolyte solution discharged from a manganese electrolytic cell as the leaching medium. Leaching efficiency based on removal of the manganese from the ore ranged from 83 to 89 percent for all systems tested.

Jan 1, 1965

By R. E. Siemens

A process is being developed by the Bureau of Mines to selectively recover nickel and cobalt from low-grade domestic laterites. In laboratory evaluation of the process, the oxides in the laterite were selectively reduced with carbon monoxide at temperatures from 350° to 600° C. For material containing more than about 5 percent magnesia, pyrite additions or post-reduction heat treatments were necessary to achieve satisfactory nickel and cobalt extraction for this range of reduction temperatures. Multistage leaching of the reduced material at ambient temperature and pressure in the presence of oxygen, ammonium sulfate, and ammonium hydroxide extracted up to about 90 and 85 percent of the contained nickel and cobalt, respectively. The nickel was selectively recovered from the leach solution by solvent extraction and was then stripped from the loaded organic with dilute sulfuric acid to provide a nickel-rich electrolyte. Treatment of the raffinate with hydrogen sulfide resulted in the recovery of cobalt as a sulfide. The only contaminant in solution was magnesium which was removed by ion exchange or precipitation. In this process the energy requirements are relatively low and except for minor operation losses, only coke and oxygen are consumed.

Jan 1, 1975

To provide a faster means to open and close permissible electrical enclosures. Approach: An inspection and repair port with a multiple start thread which provides a permissible joint has been developed and tested. How It Works: The inspection port screw thread has a large pitch, which allows the port cover to be rotated from fully closed 10 fully open, in less than one revolution. See Figure 1. When the cover is screwed back in. it be-gins engagement within one eighth turn because the screw design has eight separate threads. To prevent Its unauthorized opening, the port cover has a bolt guarded by ears which accept a padlock. The threads are designed to tolerate a reasonable amount of grit without binding, although wipe-off cleanness is necessary during reassembly. Enclosures of two different sizes each fitted with the quick-access port, were

Jan 1, 1976

By Oliver Bowles

As the preface states, this bulletin is the fourth of a series of re- ports by the Bureau of Mines on different phases of quarrying in the United States. The first part of the bulletin describes the chief types of cements, the growth of the cement industry in this country, and the character of the raw materials used. The bulk of the report deals with quarrying methods and equipment, and gives especial attention to drilling and blasting; a chapter on rock mining and one on pros- pecting are included. Methods of manufacture are mentioned briefly, as that subject, except as related to quarrying, lies outside the scope of this report; but transportation methods and the effects of the man- ner of mixing the materials at the quarry or crushing plant on quarrying methods are discussed.

Jan 1, 1918

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

MINE VENTILATION NETWORK ANALYSIS

Jan 1, 1977

To reduce the possibility of injury to operators and damage to equipment caused by collision of mining vehicles during coal loading. Approach An energy-absorbing bumper was developed and tested underground on a continuous miner. How It Works The bumper, a long box-like weldment backed by five energy absorbers, is attached to a continuous mining machine by a hinge behind the cab. See Figure 1. When a shuttle car collides with the bumper, or when it is otherwise struck, the energy absorbers are compressed. This absorbs and dissipates part of the kinetic energy of the colliding vehicle, thereby reducing or eliminating its destructive effects. Each energy absorber consists of two chambers separated by a freely-moving piston. One chamber (Figure 2) contains hydraulic fluid. The second chamber contains a gas. When a collision causes the absorber to compress, the hydraulic fluid in the first chamber is forced past a metering pin and through an orifice. The hydraulic fluid then pushes against the piston, compressing the gas in the second chamber.

Jan 1, 1978

By James R. Means, George Bowser

A new phone system was developed that provides eight full duplex communications channels over a single twisted shielded phone line, with no central switching station or line amplifiers. This system greatly simplifies installation and maintenance over that required with conventional switching systems. The system is based on microprocessor technology and digital frequency synthesis. Frequency division multiplexing is used over a bandwidth of approximately 300 kHz, and a baseband voice channel (compatible with conventional pager phones) is provided as a backup to assure communication if the multiplex features fail. Multiplex operations are controlled over a 30-kHz digital channel. The system is designed to operate with up to 16 km (10 miles) of cable plant and a maximum phone separation of 8 km (5 miles). The digital techniques permit a limited amount of monitoring and control capability to each phone. This consists of two pair of contact inputs or outputs, to be used as desired. These "flags" may be read or controlled by a dispatcher's phone.

To facilitate compliance with title 30 CFR 75.1001-1(b), which requires testing and calibrating of trolley line automatic circuit interrupting devices at intervals not to exceed six months. Approach Calibration of a circuit breaker ideally implies the passage of the expected fault current through the sensing circuit, and observing a successful circuit interruption at the preset level within a specified time. On trolley lines, the required current may be a few thousand amperes, with maximum duration well exceeding one-tenth of a second. Any method of obtaining this calibration current Involving the trolley wire can contribute to wire sagging and other permanent damage to the haul-age system due to the high energy dissipated during the test. Also, control to assure that exactly the required level and duration of current flow is obtained implies the use of equipment which is simply not available In the ordinary mine. Under a Bureau of Mines contract, a circuit to achieve the necessary calibration pulse was conceived and built. How It Works Two prototype units were fabricated and have been field tested by MSHA technical support engineers in under-ground mines. The equipment consists of an electronics Package 20 x 24 x 8 inches and weighing 93 pounds, including a side-mounted circuit breaker, with a set of 8 foot long detachable, AWG #4/0 leads with plier-type clamps. The total lead assembly weighs 21 pounds.

Jan 1, 1981

Reduce the number of accidents caused by slips and falls from large mining equipment. Approach A powered lift was developed that provides operators with a safer way of getting on and off large machines. How It Works The powered step is designed to lift personnel and materials to working levels on large machines. It eliminates hazardous blind steps and makes it unnecessary to climb on irregular surfaces made slippery by mud, ice, snow, and accumulations of grease. The step is powered by a self-contained electric/hydraulic unit which is connected to a vehicle's auxiliary power supply. When in the "down" position, the step rests about 15 inches above ground level. When the power unit is activated with an electrical switch located on the step, a Single cylinder attached between two lifting arms smoothly lifts the step. In conjunction with the lifting motion, a linkage and bearing arrangement on the mounting end of the lift arms causes the step to rotate towards the machine, so that the step moves in an arc from ground to platform level. When the machine Is operating, the step is automatically locked in the "up" position, protecting it against any damaging contact with obstructions. The step is lowered by activating a pressure release solenoid. An in-line orifice controls downward speed and prevents free fall. On most machines, additional control switches are conveniently located at ground level and in the operator's cab. Visual alarms and machine interlocks are provided where necessary to prevent machine operation when the step is In the "down" position. The powered step can be easily adapted to any type or model of large machinery.

Jan 1, 1981

Provide an unobstructive means of measuring small changes in distance from roof to floor or from rib to rib of a mine opening and the rate of closure in order to help operators of under-ground mines detect hazardous ground conditions. Approach A small ultrasonic measurement system was developed to detect g round movement and define closure rates. How the System Works The system contains two parts: a transducer and a readout device. The small ultrasonic transducer, similar to an audio speaker diaphram, is plucked with an ultrasonic frequency every six seconds. This frequency wave is sent through the air and reflected back to the transducer off any surface at which the transducer is pointed. The amount of time needed by the ultrasonic wave to make this round trip is accurately measured using a precise oscillator / timer and is converted into a measure of distance. The accurate 6-second time interval is used to convert any subsequent changes in the reading to a rate of change in feet per minute. Two readings are then displayed alternately on the readout instrument.

Jan 1, 1984

Reduce respirable dust exposure of workmen operating auger-type continuous mining machines. Approach: An auger miner was fitted with an exhaust system which draws dust laden air through a [scruber] and discharges it behind the line curtain. How It Works: Dusty air is drawn into the space above the coal conveyor and through a scrubber, by two fans mounted side by side above the conveyor. Exhaust from the fans passes through a duct to the side of the auger miner, and into tubing that runs back and into the air return passage formed by the line curtain. See Figure 1. Of the 5,000 cubic feet per minute of air normally entering the working place, 4/5 is drawn out through the dust exhaust system. The system was installed on a Wilcox Mark 20 Miner and tested underground by personnel of the Bureau's Pittsburgh, Pa., Mining and Safety Research Center, under a cost sharing

Jan 1, 1976

A system to continuously measure the concentration of radon in mine ventilating air has been developed and tested in a uranium mine. In use, the air/radon mixture to be monitored is pumped through filters into a scintillation cell where nuclear decay of the radon produces flashes of light. These are electronically counted, giving a quantitative measure of the radon present. Air is continuously drawn from the mine atmosphere into the radon sensor box. This air sample passes through two filters into the detector cell as shown in the schematic diagram. A portion of the radon in the detector cell will experience nuclear decay, producing polomium 218 and an alpha particle. The alpha particles from the fraction that decays strike a zinc-sulfide coating on the inside wall of the cell and produce flashes of light. These enter a photo-multiplier tube which records each flash as an electrical pulse. An amplifier increases the voltage of each pulse, allowing electronic screening to remove noise and other undesirable pulses. The remaining pulses are counted by a conventional data acquisition system.

Jan 1, 1978

By Terry L. Muldoon

The report describes the development of preliminary requirement specifications for standardized operating controls for roof bolting machines used in underground coal mining. According to recent statistics, roof bolting continues to be one of the most hazardous occupations in underground coal mining. The two principal hazards to the roof bolter operator are the machine itself and roof falls during the bolting cycle. The lack of standardization of machine controls is a major contributor to this hazardous situation. Observations of roof bolting operations and discussions with roof bolter manufacturers coupled with detailed analyses of roof bolter control design specifications were performed during this study. Detailed roof bolter operator task analyses, commonality of control analyses, and classical link analyses were also performed. The results of these analyses were then used to produce preliminary requirement specifications for standardized controls.

Jan 1, 1980

By Nicholas Kyriazi

A joint effort by the U.S. Bureau of Mines (USBM) and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CPR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR's in the fourth phase of testing from 1989 to 1993. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except units with manufacturing defects. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. In addition, some apparatus collected for this study had not been returned to the manufacturer in a recall effort for correction of a manufacturing defect. In both cases, the apparatus would have presented problems in emergency use. Recommendations include improved training in inspection procedures and better enforcement of recall notices.

Jan 1, 2010

By Willard L. Hunter

The separation of tantalum and columbium by solvent extraction was under-taken as part of the Bureau of Mines research program to improve methods for extracting, separating, and reducing these elements to metal. The diethyl ketone aqueous HCl-HF system was one of several systems studied to determine the effect of metal and acid concentrations in aqueous solutions upon the transfer of tantalum and columbium into selected ketones. The tantalum-columbium oxide mixture used in this investigation was obtained by chemical extraction from Geomines slag. The investigation showed that tantalum 99.4 percent pure and columbium 97.2 percent pure can be produced by the selective transfer of tantalum into diethyl ketone from a solution of 2-N HF and 1-N HC1. The relatively low acid concentration necessary for tantalum transfer and the excellent selectivity of the system recommend its use for the separation of tantalum and columbium.

Jan 1, 1961

By Larry A. Haas

The U.S. Bureau of Mines is investigating ways of enhancing the high-temperature softening-melting (HTSM) properties of domestic taconite pellets. These properties, which are important for determining the performance of pellets in blast furnaces, include pellet bed contraction, pressure drop, S-value (area under the pressure-temperature curve), and softening and metal-slag drainout temperatures. Experiments showed that HTSM properties were related to the physiochemical properties (fired strengths and reducibilities) of pellets containing different levels of limestone and dolomite flux. Flux additions resulted in slightly lower green and fired pellet strengths, but improved metallurgical properties, such as reducibility. The influence of reduction conditions on HTSM properties was evaluated by varying the pellet metallization starting temperature and the carbon monoxide content of the CO-N2 gas mixture. HTSM property change was more sensitive to flux addition levels when metallization was initiated at 1,100° C with 20 pct CO in the gas stream. The S-value and the metal-slag drainout temperature were found to be the best criteria for characterizing HTSM properties. The optimum flux addition level was about 8 pct (4 pct dolomite, 4 pct limestone) or a basicity of about 1. At higher flux levels, a higher metal-slag drainout temperature was obtained.

Jan 1, 2010

By Jr. Sillers

This is the third report of investigations dealing with the application of electrolytic manganese to steel-foundry practice and the seventh in a series of reports dealing with tests to establish the technological acceptability of electrolytic manganese in the iron and steel industries. The work was carried out by Metallurgical Division of the Bureau of Mines as part of an extensive program for the development and utilization of domestic ores. The electrolytic manganese used in the tests was produced by the Bureau at its Boulder, City, Nev., pilot plant by the process developed by the Bureau of Mines.

Jan 1, 1949