Search Documents

By H. W. Frevert, A. C. Fieldner, S. H. Katz

"The Bureau of Mines, in its investigations of as masks for use in mines and allied industries tests masks that are voluntarily submitted by manufacturers for examination, and issues approval certificates for masks that meet the bureau's specifications. This paper describes the tests that were conducted on an ammonia gas mask by the Bureau of Mines, which successfully met all requirements and tests for ammonia, masks. The mask tested, known as the GMD ammonia gas mask, is manufactured by the Mine Safety Appliances Co., Pittsburgh, Pa. This ammonia gas mask, which forms a pocket over the face and allows breathing through the nose, consists of a face-piece with non-shatter eyeglasses; this is attached by means of a corrugated rubber tube to a canister supported on wearer's chest by a harness. The canister is green in color and is of tinplate construction. It was a disc valve at the bottom to prevent exhalation through the canister. The filling of the canister consists of a specially impregnated activated charcoal, about 750 c.c. in volume and weighing about 520 grunn. The material is supported above the check valve by a dome of wire screen covered with toweling. Above the granular material is a filter of absorbent cotton screens, and all materials are hold firmly in place by pressure from strong"

May 1, 1926

Eliminate the need for roof bolter operators and their helpers to work under unsupported roof while setting or removing temporary supports before or during the roof bolting cycle-a task that annually accounts for approximately 20 percent of all roof fall fatalities. Approach The Bureau of Mines designed, built, and field tested an auto-mated temporary roof support (ATRS) that can be carried from place to place on the drill head of a single, fixed-head roof bolting machine (squirmer) used in low coal seams (less than 42 inches thick). How It Works The ATRS is designed for installation on any streamlined squirmer. It consists of a ten? foot-long, steel, wide-flange beam supported by two double-acting, telescoping hydraulic cylinders. A steel sleeve, mounted on the bottom center of the beam, is designed to fit over top of the

Jan 1, 1983

By Thomas A. Morgan, Louis A. Panek

This report describes a method for determining the stress in rock based on a requirement for static equilibrium ; namely , that the total load on a sufficiently large area must remain constant even after a drift or stope is mined in the area . The method is based on mathematical relationships that are independent of the elastic properties of the rock and the stress distribution near the underground opening . In addition to determining the preexisting stress (before mining ) , the method described can be used to determine the change in stress due to mining .

Jan 1, 1963

By E. W. Dean, W. A. Jacobs

"The petroleum division of the Bureau of Mines in its laboratory investigations, has had occasions to develop a number of types of electrical heating equipment. It was found that electric heaters could be used to particular advantage in the standard distillation test for gasoline. (Dean, E.W., Motor Gasoline, Properties, Laboratory Methods of Testing and Practical Specifications, Bureau of Mines Technical raper 214, 1919, 33 pages.) In order to assist in rendering this type of heater available for general use, a description of the apparatus developed by the Bureau was published. (Dean, E.W., A convenient electric heater for use in the analytical distillation of gasoline,. Jour. Ind, and Eng. Chem., Vol.10, 1918, page 823.) Shortly after the article was printed a chemical supply house undertook the manufacture of an electric heater suitable for gasoline distillation. A preliminary model was examined and tested by the Bureau and modifications were suggested that were incorporated in the type of heater that was finally marketed.Description of the Bureau of Mines-heater: The electric heater developed by the Bureau has an inverted conical resistance Plament surrounded by a layer of heat-insulating material and mounted in a metal case having a top of hard asbestos (Transite) board. The resistance element is a helix of nickel-chromium alloy wire held by a molded core of alundum. The Bureau heaters are generally of about 330 watts capacity and are used with stock types of regulating rheostats capable of reducing the effective wattage to about 43 the full-load maximum."

Jun 1, 1920

By Gordon H. Dechman

This Bureau of Mines report presents an iterative approximation method for microseismic source location that was developed to adapt microseismic techniques for rock structure analysis to investigations of surface problems, such as slope failure in an open pit mine. The source location method and two derivative location algorithms are described in detail, and the speed and accuracy of the two algorithms are compared.

Jan 1, 1977

By David P. Lindroth

The Bureau of Mines has developed and successfully tested a hangup clearance module for use in clearing hangups in underground mine chutes and ore passes. The Bureau's tests showed that the hangup clearance module can be effectively used to clear mine hangups. Furthermore, it is believed that clearance using this module is quicker, safer, and more efficient than the method currently used. The hangup clearance module uses a ballistic disk explosive charge that can clear hangups located as far as 50 feet (15.2 m) from the position where the charge is detonated. Mine personnel can therefore set up the module and the charge it contains without being exposed to dangerous areas. This report describes the principles of operation of the module, provides data and drawings for its construction, and gives instructions for its setup and use. The report also summarizes the development of the module, briefly discusses preliminary and underground tests, and lists the current and potential applications of the hangup clearance module to underground mining.

Jan 1, 1982

By W. W. Adams

"During the calendar year 1925 the Bureau of Mines received from the operators of several hundred mines and quarries complete accident records covering deaths, permanent disabilities, and “lost time” temporary injuries. Some of the companies, - those that participated in the National Safety Competition-also furnished information showing the number of man-hours of work performed during the year. With these two types of information it was possible to calculate the accident-frequency and accident-severity rates of the different plants. Complete and comparable reports of accidents and Man-hours of “exposure” were received from 34 underground metal mines, 59 underground coal mines, 15 underground mines producing other nonmetallic minerals, and 102 open quarries or open-pit mines. The figures in the table appended to this report show the accident severity rates and other data for each of the 34 underground metal mines and for the group as a whole. It is proposed to publish similar figures for the other classes of mines and quarries at an early date.The 34 metal mines listed in the table are situated in Arizona, Idaho, Kansas, Michigan, Minnesota, Missouri, New Jersey, New Mexico, Oklahoma, South Dakota., and Utah; they employed 5, 925 men, an average of 174 men per mine, including employees above-ground as well as underground. With but few exceptions, 50 men was the minimum number of employees in any mine. The total period of employment or “exposure” at the 34 mines was 14,612,607 man-hours, an average of 2,466 hours per man, or the equivalent of 308 work-days of eight hours for each employee. Accidents resulted in 15 fatalities, 9 permanent disabilities, and 1,950 temporary “lost time” injuries (causing disability exceeding remainder of shift). The fatal and nonfatal injuries represented 132,575 days of disability. Thus the accident frequency rate for the group was 135 accidents per million hours and the accident severity rate was 9.073 days lost per thousand hours of 1 “exposure”. The severity rates ranged from 0.227 to 88.653, while the ·range of the accident-frequency rates was from 16. 6 to 307 .4. In compiling the accident severity rates shown in the table, all accidents caused by explosives were weighted at twice the number of days actually lost, as one of the purposes of the National Safety Competition was to stress the prevention of accidents caused by explosives."

Sep 1, 1926

The purpose of this study is to formulate practical guidelines for active underground mining in close proximity to water bodies. This was accomplished through systematic completion of three phases of study: I) Collection and Documentation of Data; II) Application of Existing Guidelines to Case Histories of Previous Inundations; and III) Development of Recommended Guidelines for Underground Coal Mining Near Bodies of Water. Phase I of the study involved a worldwide data collection effort designed to obtain foreign and domestic guidelines for mining near water bodies, and accident records and case histories of accidental mine inundations. Within Phase II, existing guidelines were categorized and classified and then evaluated as to their effectiveness in precluding past inundations had they been in effect at the time of inrush. Advantages and disadvantages of existing guidelines were defined. Drawing on the broad data base established in previous study efforts, Phase III was directed at development of viable guidelines to promote the greatest possible coal extraction while precluding accidental mine inundation. Two levels of guidelines are presented; Level I Guidelines require little or no subsurface exploration on the part of the mine operator, while Level II Guidelines recommend various testing and investigative procedures to permit greatest possible mineral extraction. This report presents findings and conclusions of the study.

Jan 1, 1976

By H. P. Rue

For the proper control of gasoline treating plants there is need of a quick test for corrosion. In "sweetening" gasoline that is, in treating it to remove evil smelling mercaptans or to convert them to disulphides or sulphides the sodium plumbite ("doctor") method is generally used. This method involves agitation of the gasoline with "doctor solution's (sodium plumbite made by dissolving litharge in a solution of caustic soda) in the presence of free sulphur3. One of the common mistakes in the technique of this process is the addition of too much free sulphur, which will dissolve in the gasoline and cause it to be corrosive. In the operation of a continuous sweetening; or treating plant, a check on the corrosiveness of they product is imperative at all times. The copper-strip test commonly used in specifications take, so long to perform that the plant may fail to function properly for some time before the operator discovers it. The writer has investigated a rapid corrosion test method involving the use of metallic mercury, recently developed by Messrs. G. T. Granger, refinery superintendent, and A. B. Comstock, chief chemist, of the Barnsdall Refineries, Inc., Okmulgee, Okla. They have used this test successfully for several months in controlling the operation of their continuous treaters any have come to the conclusion that it has several advantages over the copper-strip test. Chief among these is the time caved, as the copper-strip test takes at least one-half hour, while the mercury test can be wade in about five minutes. It is very evident that this is an important item in controlling a continuous treater.

Jan 1, 1928

By E. J. Kloos

The Bureau of Mines evaluated all previously approved gas masks to determine their ability to provide respiratory protection against each of the following six selected amines: ethylenediamine, diethylamine, n-butylamine, ethylamine, methylamine, and hydrazine. Minimum requirements were a 24-minute service life at a flow rate of 64 liters per minute (32 liters per minute for hydrazine) and an amine concentration of 1.0 volume-percent (0.5 volume-percent for hydrazine). The three masks meeting these requirements were the LG4, Willson Products Division, The Electric Storage Battery Co.; the GMD-SS, Mine Safety Appliances Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

By C. H. Gorski

Evaluation of raw materials for mineral wool is one phase of the Bureau of Mines broad program for the more effective utilization: of our mineral resources. The experimental work and test-evaluation results on several raw materials as useful components for the production of mineral wool are presented in this report. Samples from all sections of the United States, including copper slag from Tacoma, Wash., pebble phosphate slime from Florida, and granites from Massachusetts and Minnesota, have been blown into mineral wool successfully in the laboratory tests. Maximum conservation of the Nation's mineral and manpower resources requires maximum utility of those resources. Al though the domestic reserves of oil, gas, and coal are tremendous, judicious use of these fuels through the use of proper insulation will insure the highest thermal efficiency. The effectiveness of mineral wool as a heat-insulating material has assumed an increasingly important role in the national economy, and it has become a fuel saver in countless applications. The most immediate concern to many is the use of mineral wool in the home, which promotes uniform temperature and minimizes drafts by reducing heat transfer through the walls, ceiling, and floors. There are, however, many industrial and commercial uses that require large volumes of mineral wool each year.

Jan 1, 1951

By M. L. Bowser

Pulse-forming circuitry is described for use in explosives research that requires precise synchronization and control of events in order to investigate detonation parameters. Included are pulse generators for oscilloscope sweep control, counterchronograph actuators, and a raster-type oscillographic method for the determination of velocities of detonation that are applicable to studies on solid, liquid, and gaseous detonations. INTRODUCTION Prom time to time, requests have been received for information on electronic circuitry used in explosives work at the Explosives Research Laboratory, Bruceton, Pa. The methods used are not entirely original;4 5 6 however, modifications of earlier techniques and some novel design aspects have resulted in time-tested methods that warrant a more detailed description.

Jan 1, 1962

By Alan Mayton, N. Kumar Kittusamy, Christopher Jobes, Farid Amirouche

Industrial equipment exposes individuals to whole-body vibration (WBV) and mechanical shock. This exposure can negatively impact their health, safety, comfort, and working efficiency and performance. Accordingly, proper seat design is an important consideration in reducing the adverse effects of WBV exposure to vehicle operators. Since the human body is sensitive to low frequency WBV, ride quality is a basic and important element of good seat design. When designing a suitable seat, it is essential to understand vibration exposure environment of workers and how well they can tolerate this environment [1]. This is particularly true in the mining industry. Mayton et al. [2] reported on a low-coal shuttle car seat design that underwent limited, yet successful underground mine trials. Building on this work, a follow-up study compared NIOSH and existing seat designs on low- and mid-coal seam shuttle cars. The NIOSH seat designs included viscoelastic foam, which has properties similar to those found in a mechanical spring/damper suspension system. The seats also included an adjustable lumbar support and a fore-aft seat adjustment. The NIOSH seat designs contrast with the existing seat design, which have little or no lumbar support and include inexpensive foam padding of the type commonly used in furniture. This paper will focus on the seat designs for the mid-coal seam shuttle car and compare subjective comfort data collected from five vehicle operators with ISO 2631 – based reduced comfort boundary (RCB) analysis of recorded vibration levels. Methods Experimental data were collected using three different tools: triaxial accelerometers, pre-amplifiers, and filters connected to a data recorder; a visual analog scale (VAS); and a short questionnaire. Researchers recorded quantitative or objective vehicle vibration data to determine the input and output acceleration at the operator cab floor and operator seat interface. Qualitative or subjective data, collected with the VAS, allowed researchers to obtain the operators’ immediate impressions of shock, vibration, and discomfort levels for the vehicle ride on each of the seat designs. Each shuttle car operator made six round trips with the vehicle each seat. The shuttle car operator marked the VAS on the first, third, and sixth round trip of the trials for each seat. A round trip consisted of traveling to the coal face with no load and returning to the load discharge location with a full load of coal. Results Total overall average ratings for the five vehicle operators of the mid-coal seam shuttle car, showed that operators sensed from 45 to 87% less discomfort with NIOSH seat designs compared to the existing seat design. Using a 95% CI, researchers computed a strong positive correlation for discomfort. Figure 1 illustrates the RCB analysis method for one of two NIOSH seat designs.

Jan 6, 2006

By Rimas Pakalnis, Tom Brady, Lewis Martin

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate weak rock masses (such as are associated with operations in the Carlin Trend in Nevada) into existing design relationships. The original database that led to most of the empirical design relationships presently employed in hard-rock mining was derived from fair-to-good-quality rock. In this study, the relationship between weak rock quality and opening design (non-entry/entry methods) is being investigated. The common factor in all mines is a weak back or wall. This work attempts to provide tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment. Tom Brady (for correspondence - E-mail- thb6@cdc.gov)and Lewis Martin are at the Spokane Research Laboratory, National Institute for Occupational Safety and Health, 315 East Montgomery Avenue, Spokane, WA 99207-2291, USA (E-mail• ljm8@cdcgov); Rimas Pakalnis is at the Mining Department, University of British Columbia, Vancouver, British Columbia, Canada (E-mail: rcp@mining.ubcca).

By R. F. Abernethy

The work discussed in this report was done by the Bureau of Mines to develop a method for determining trace amounts of fluorine in coal. Samples of coal mixed with calcium oxide as a fixative agent for fluorine were ashed at 600° C and the residue was fused with sodium carbonate. The melt was dissolved in phosphoric and sulfuric acids and distilled to separate the fluorine) which was determined in the distillate by a SPADNS-zirconium spectrophotometric method. Fluorine determinations of 83 commercial coals ranged from 0,001 to 0.019 percent.

Jan 1, 1967

By Walter E. Lewis

The Fort Randall Reservoir project, on the Missouri River at Pickstown, S. Dak., was designed by the Corps of Engineers and is part of the Missouri River Basin Development Program. The location of the project with respect to adjacent features is shown' in figure 1. When the project is finished, it will include a large earthwork dam and 12 circular tunnels, 8 of which will be equipped for power and 4 for flood control. Various phases of the construction have been contracted to independent companies, and at present four companies are working on different phases of the project under a rigid time schedule. Western Contracting Corp. is the contractor on stage II, earthwork; Johnson-Winston Construction Co. is the contractor for construction of the intake towers at the upstream side of the dam; McCarthy Improvement Co. has the contract for the power house and the outlet works on the downstream side; and Silas Mason Co. has the contract for driving the power and flood-control tunnels. The latter two companies use the same roads for ingress and egress to their respective work areas and the same general waste dump area. Under such circumstances, it is necessary that each company stay on a time schedule in regular sequence to avoid interference with the other.

Jan 1, 1951

By F. E. Spencer

This Bureau of Mines report provides a complete mathematical description of the algorithm employed by a general multiphase chemical equilibrium program developed particularly for the purpose of studying problems in coal combustion, although the generality of the program will allow its application to any equilibrium system in which an appreciable gas phase is present. When applied to coal combustion problems, the program predicts composition and quantity of slag and unconsumed carbon phases as well as calculates accurately the composition of the gas phase including trace species such as free electrons and ions which are important for predicting electrical properties.

Jan 1, 1973

By R. V. Ramani, K. V. K. Prasad, M. Swaminathan

"INTRODUCTIONMine ventilation planning is an engineering design process requiring a substantial amount of qualitative knowledge obtained through experience. A concept for a knowledge-based ventilation expert system was developed by Ramani and Prasad (1987).1 11 An expert system based on the above scheme was conceived with the motivation of providing a tool to facilitate decision making for ventilation engineers in the context of computer assisted ventilation planning. Options for the implementation of the system were then examined and several commercial, personal computer (PC) based shells assessed toward this end. The options considered, the evaluation criteria and procedure arc discussed in Prasad ·and Ramani, (1989).Cll Following the above study, a scheme was developed to represent the components of the expert system.<3> Evaluation of several commercial shells indicated that there was none available which permitted interfacing with a large external algorithmic program. It was therefore decided to develop the KBS in LISP and custom build the necessary interfacing routines to ""hook out• to the network analysis program (NAP). Due to this choice of development strategy, the computer implementation aspects of the KBS arc important as all the interfacing components had to be developed with the basic tools offered by LISP.In this paper, the implementation of the knowledge based system (KBS), in terms of its component, the interfaces among the various components of the KBS and between the KBS and the user arc described. The ventilation KBS consists of an AES (analysis expert system), an IES (interpretation expert system)' and an algorithmic NAP (network analy5is program). The AES analyzes the input to the NAP considering the legal 5tipulations governing the various mine ventilation network parameters and principles of good ventilation, helping the ventilation engineer develop and represent represent the problem for solution by the NAP. The IES diagnoses the output from the NAP in terms of the critical parameters in the context of the given problem. Thi5 loop is continued till a satisfactory salution is obtained. The implementational details of the AES, the IES and the approaches to the validation of the expert system arc also discussed."

Jan 1, 1990

By Robert J. Hundhausen

During the early part of World War II , it appeared likely that supplies of chromite for United States industry might become critically short . As a part of the ensuing search for new sources of domestic chromite supply , the chromite - bearing black sands along the coast of southern Oregon were hurriedly investigated by State and federal agencies and by private interests , These investigations led to a decision to begin exploitation of the deposits immediately . A government stock- piling program was put into effect , a concentrator was financed by the Defense Plant Corporation , two privately controlled companies were encouraged to start mining operations , and the Bureau of Mines and the Geological Survey were authorized to search. for additional reserves of minable ore .

Feb 1, 1947

By C. M. K. Boldt

The Bureau of Mines studied the compaction characteristics of metal and nonmetal tailings. Densities of the tailings and zone of compaction influence, compactive effort, and cost of equipment are related to changes in the factor of safety for specific grain-sized tailings and embankment configurations. Field testing was accomplished in two distinct phases. The first phase investigated the effectiveness of using a nuclear gauge on metal and nonmetal tailings to produce rapid, instantaneous measurements of moisture content, wet density, and dry density. The results of the nuclear gauge testing are presented in chapter 1. Chapter 2 presents a comparison of the compactive effectiveness of three different pieces of construction equipment on a coarse-grained metal tailings pond. The three pieces of equipment chosen for study were a DBH track-mounted dozer, a DSOO rubber-tired dozer, and a SP848 vibratory smooth-drum compactor.

Jan 1, 1985