Search Documents

By Dennis R. Dolinar

The National Institute for Occupational Safety and Health?s Pittsburgh Research Laboratory conducted a full-scale test of a composite polyurethane-aggregate seal in a hydrostatic chamber at the Lake Lynn Experimental Mine. This composite seal consisted of a polyurethane and limestone aggregate core that was formed between two concrete block walls. In the hydro-static chamber test, water is used to pressurize the seal. During the test, the maximum average water pressure the seal was able to withstand was 18.9 psi. Further, the seal began to yield at an average water pressure of only 17 psi. At the time of the test, the minimum seal design requirement was 20 psi under 30 CFR4 75.335 (2005). Therefore, based on this test, the seal did not meet the regulatory minimum design requirement. Uniaxial compressive tests conducted on samples from the polyurethane-aggregate core revealed that both the compressive strength and the elastic modulus of the material were much less than that for polyurethane only with a density of 10.0?12.0 lb/ft3. The significant reduction in the strength and stiffness of the polyurethane-aggregate mixture results from the formation of a soft polyurethane foam around each piece of aggregate. The formation of the soft foam seems to be caused by residual moisture from the aggregate. The moisture also caused the density of the polyurethane in the polyurethane-aggregate mixture to be less than the design requirements. The lower density of the polyurethane in the mixture, along with the formation of zones of pure polyurethane only, resulted in the overall seal density being less than the design requirements. During seal construction, steps were taken to control the moisture, but were not successful. An analysis of the seal failure showed that the calculated shear stresses at failure and the estimated shear strength of the polyurethane-aggregate mixture are fairly close. This suggests that the strength properties of the polyurethane-aggregate mixture along with a weak zone of poorly bonded aggregate controlled the maximum pressure the seal could withstand. At the time of the seal testing, the minimum design requirement was 20 psi, as specified at 30 CFR 75.335 (2005). New emergency temporary standards for seal designs were promulgated on May 22, 2007, with a minimum requirement of 50 psi under specified conditions. However, it will be shown that the evaluation of the polyurethane seal performance as designed to meet the older 20-psi criterion can be relevant to the design requirements under the new standards.

Jan 1, 2008

A working understanding of present coal mine communications equipment and its usage is an essential prerequisite to the determination of future communications systems needs. As a means of gaining this understanding, a field survey program was planned and implemented. The plan formulated called for obtaining both qualitative and quantitative data from three main areas of interest: the types, physical condition, and performance characteristics of equipment presently used in the sample of mines to be visited; the relationship present communications has to safety and productivity; and the practical, future communications needs as derived through interviews with present mine management. In compliance with the original plan, the type and physical condition of equipment in use was found through at-mine interviews of personnel responsible for installation and maintenance. Further evaluation was made through the review of equipment instruction books and maintenance manuals and through in-mine inspection of communications equipment and signal distribution networks. The performance characteristics were determined through listening to conversations and noise levels and by talk-testing from randomly selected stations throughout each mine. System operation was evaluated by asking communication system users their opinions and by noting any difficulties personnel had using the systems.

Jan 1, 1974

The Bureau of Mines, through its Minerals Availability Program (MAP), investigates the mineral supply potential of the United States and market economy countries (MEC's) for a number of minerals considered essential to the U.S. industrial base. Major activities include identification of important mines and mineral deposits, estimation of their mineral resources and production costs, and availability and sensitivity analyses. Products include data print-outs of geological and engineering information, discounted- cash-flow rate of return (DCFROR) analyses of individual mining operations, commodity availability appraisals, and analytic services to Government agencies. These products are used in assessing the mineral supply position of the United States: in setting priorities for research aimed at reducing production costs and minimizing adverse environ- mental impacts and regulatory compliance costs of mining and mineral processing operations; and in formulating and evaluating Government policies that affect minerals. Bureau MAP data and analyses have been provided to the executive and legislative branches to aid in consideration of trade, tax, and stockpile policy issues. A study of the economic potential of selected seabed mineral resources supports the regulatory responsibilities of the Department of the Interior in the U.S. Exclusive Economic Zone. Analytic studies of mineral project viability, industry competitiveness, and import dependencies were also undertaken for, or in cooperation with, U.S. and foreign government agencies, industry and trade organizations, and international lending institutions.

Jan 1, 1987

By A. F. Roberts

The subject of mine fires is a very wide one. To give reasonable coherency, the paper concentrates on the behaviour of fires in the ventilated airways of mines; spontaneous combustions are not considered. The following topics are considered in some detail: 1) Material selection: Performance requirements for mining materials in terms of flammability and smoke/fume production; methods of test and need for relevance to mining conditions. 2) Fire growth: The influence of material properties and method of use on the rate of growth of fire in a mine roadway; the influence of ventilation, slope, material orientation, proximity of walls and roof on fire behaviour. 3) The fire in the ventilation network: The influence of fire on the ventilation distribution; the circulation of fire products in the network. The influences of these topics in determining fire control strategy are then considered but topics such as fire detection and fire extinction methods are not reviewed in detail. An extensive Bibliography on papers relating to mine fires is included.

Jan 1, 1989

After a stagnant performance in 1982, gross national product (GNP), industrial production, and employment increased during 1983 in nearly all industrial nations, with the U.S. performance generally leading the uneven worldwide recovery. Real U.S. GNP increased 3.3 percent in 1983 (table I). Although investment in nonresidential structures declined, total nonresidential fixed investment in the United States was up 1.5 percent following a 1982 decrease. The increase in worldwide industrial activity and demand in 1983 put greater pressure on prices in many countries. Prices increased from less than 3 percent in the Federal Republic of Germany, Japan, the Nether-lands, and Switzerland to as much as 10 percent in nearly all the other Organization for Economic Cooperation and Development nations. The annual inflation rate in the United States was 4.3 percent (based on the GNP fixed-weight price index).

Jan 1, 1984

By Kenneth R. Maser

This report describes the development of a system which modifies an existing fly ash-foam remote mine sealing technique to make it capable of impounding water in a fire zone. The modification involves blending equal quantities of fly ash and bentonite to form the bulk of the seal, and blending a thin layer of fly ash and Huron Regulated Set Portland Cement (RSPC) as a coating. The modification replaces the pure fly ash approach, but continues to use a froth foam topping to complete the seal. The modified material system is implemented with minimal complexity by adapting a "Y" connector to the existing delivery system. Each bulk hauler (fly ash and bentonite, or RSPC) will pump into one leg of the 'Y'; and the blending will be controlled by two pinch valves. The development effort has involved an evaluation of potential material systems by using small sample, quarter scale, and full head tests. The small sample tests measured the basic properties of a large number of selected material combinations. Property measurements included capillarity, permeability, shrinkage, and shear strength. As a result of these tests, particular combinations of fly ash-bentonite and fly ash-cement were selected for scale model testing in a 1 /4 scale test facility. These tests simulated, in a scaled manner, the water rise and total head which would be experienced by a seal. The tests indicated that shrinkage in the fly ash-cement combination would always result in leakage; whereas, fly ash-bentonite mixes were impervious to water.

Jan 1, 1974

By R. A. Cattell

With the surrender of the Japanese Imperial Government as a climax to the capitulation of the German High Command , the main objective of the Petroleum and Natural Gas Division pivoted from war assignments to its main normal functions . One of these functions is to give wide public distribution to valuable technical facts which the Division has obtained through research on petroleum , natural gas , helium , and related subjects . During the war years many engineering data and scientific facts could be released only on a restricted basis as reports to war agencies and others immediately concerned . Moreover , many of the wartime reports contained masses of detailed data that were prepared under stress to meet emergency schedules . For peacetime publication and application , these data must be reviewed , correlated , and rearranged so as to present the essentials in proper form . To illustrate , a wartime report of 50 pages might be resolved into one curve in a composite graph for a peacetime publication . Another factor affecting the orientation of the work of the Division is the broader horizon of research revealed by its war activities . Fundamental research and careful engineering analyses are just as important in time of peace as in time of war; in fact , they should be more important to the forward view , because under peace conditions disrupting influences that distract from the orderly acquisition of knowledge are minimized . Therefore , the concerted effort has been not to " salvage " the results of the war activities , but to evaluate them on the basis of their relative importance in the future economy of the country . Where wartime investigations have pointed to peacetime accomplishments , the effort has been to give the corresponding type of work additional emphasis . This adjustment can not be made hurriedly , but many of the necessary preliminary steps on the new course have been taken ..

Jun 1, 1949

MR. RIGG: Gentlemen, I would like to welcome you all to the symposium this morning. My name is Jack Rigg, and I m a special assistant to Hollis Dole, Assistant Secretary of the Interior for Mineral Resources. Hollis is not in town this morning, and I am here to pinch-hit for him. The first order of business this morning is remarks by the Honorable Russell Train, Under Secretary of the Department of Interior. Mr. Train. MR. TRAIN: Thank you, Mr. Rigg. Lest you think that Hollis Dole is not interested in this symposium, let me just say that fie is flying back from Australia just to be here. He is heading up a United States delegation in Australia meeting on resource problems in the Pacific. And I believe he will be here about noon.

Jan 1, 1970

The Bureau of Mines is the engineering arm of the Government for mineral resources. Its mission is to carry out laboratory and field studies that will assure the wise and effective development and use of our Nation's minerals, fuels, and underground domain in order to preserve the security and enhance the welfare of our people. Specifically, studies are directed to the means by which current and emerging demands may be met, the real cost of such achievements, and the assessment of related social and economic factors. Ways are sought to fulfill our material needs in a manner that minimizes occupational hazards to workers in the industry, reduces waste, and ensures that mineral raw materials are supplied and mineral-based products are used and are disposed of efficiently, without objectionable social and environmental costs. The headquarters of the Bureau of Mines is located in Washington, D.C. The Bureau's research and development program, however, is conducted at 19 research centers and laboratories located throughout the United States.

Jan 1, 1971

By David W. Tongue

This report describes the engineering work leading to the design of an underground coal mine piping system to transport approximately 2,000,000 cubic feet per day of methane gas to the surface from degasification holes drilled horizontally into the coalbed in existing coal mines. Safety instrumentation for detection of gas leaks and provisions for automatic emergency shutdown are included in the design. It also includes specifications for a safe system of handling gas, water, and drill cuttings during drilling of the horizontal holes and recommendations for compressor and metering facilities at the surface. The main pipeline is recommended to be constructed of polyethylene plastic pipe joined by a butt fusion method while lateral lines and separator and meter piping at the horizontal holes are recommended to be screwed steel piping. The materials used are to be resistant to the forces of impact exerted by falling rock. The pipelines are to be suspended from the ceiling with pipe hangers. All steel components are protected from chemical corrosion by applying protective coatings and the vertical casing to the surface is protected from electrolytic corrosion by a rectifier station. Methane gas detectors monitor the mine atmosphere to detect the presence of gas leaks and a pneumatic plastic tubing line provides for control of the safety shutdown system. Both the recommended design and the required construction procedures are in compliance with the applicable Federal codes for coal mine safety.

Jan 1, 2012

By Alan A. Campoli

The U.S. Bureau of Mines conducted research to characterize longwall gob loading under bump-prone geologic conditions. Bureau-designed stress meters were installed in the floor rock beneath two longwall panels and coal pillars in the gate road between them. Gob and gate road pillar stress was monitored continuously by a state-of-the-art data acquisition system. The timing of the final destruction of the abutment pillar's load-bearing core was optimal, since the pillar is located between two gob areas and no longer of significant importance for ground control. Maximum stress was observed immediately in front of the longwall face, and this pressure quickly dropped as the face moved past the instruments. The center of the longwall panels regained significant overburden load, while the instruments located less than 100 ft from the edge of the panel showed little or no increase in pressure due to gob reloading.

Jan 1, 2010

By Sidney Katell

This report covers the period January 1963 through December 1963; it is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. Also, it is the fifth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers. The agreement provides for the publication of an annual cost bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related subjects, are from the following sources:

Jan 1, 1964

This report, the fourth in an annual series, outlines recent trends and developments in the minerals industry. Discussed are new methods, equipment, techniques, and systems used to more effectively extract and process mineral products. Environmental considerations, health and safety standards, price controls, inflation, material shortages, and more dependence on foreign imports were problems faced by the minerals industry. Although productivity increased for most mineral commodities, the annual rate of increase has slowed in recent years, indicating a maturing technological situation. Growing concern for energy resulted in increased interest and research in alternative fuel sources. The primary concerns of metallurgists were pollution control and improved efficiency and performance of metallurgical processes, especially for reduction of energy consumption.

Jan 1, 1974

By D. Harrington, C. W. Owings

The mining industry is gradually realizing that safety education and safety inspection are economic factors that may not be overlooked as a means of reducing operating costs . Many mine operators , however , have failed to realize the benefits of safety , and the efforts of the more progressive mining companies are offset by the carelessness of neighboring companies when the accident records of a community or a State or the nation as a whole are considered . This tendency is indicated by the data collected by the safety division of the United States Bureau of Mines . During the fiscal year ended June 30, 1930 , relatively definite information: was secureä concerning 34 mine explosions , 24 mine fires , and 29 miscellaneous accidents ; these accidents are by no means all of the explosions , fires , and miscellaneous accidents which occurred in the mines of the United States during the period; but the data on the fires and explosions constitute a record of all of those types of accidents that were called specifically to the attention of the safety division , and the miscellaneous accidents include those on which definite , detailed data were obtained by the safety division .

Jan 1, 1931

By S. M. Dar

The U.S. Bureau of Mines constructed a full-scale model of a 15-ft-wide coal mine entry to use in combination with finite-element analyses to investigate roof support systems and various types of roof bolts. The objective was to enhance understanding of the fundamental mechanics of the interaction between rock and supports and the relative integrity of bolted mine roof as a function of roof bolt type, length, spacing, and tension, and the basic characteristics of the roof strata. The laboratory test results, when correlated with computer simulations using fmite-element analysis and underground verification tests, should provide a basis for desigillng safer, more cost-effective roof control systems and help to establish guidelines for employing fully grouted resin and mechanically anchored bolting systems. The background for this research, the research approach, the methods and equipment employed, and the results are described in this report.

Jan 1, 1989

By D. A. Elkins

This report is the second of a series of three that will evaluate, in order, the metallothermic, carbothermic, and electrolytic methods of magnesium production. The historical development of the carbothermic process is outlined. Production costs varying from 38.9 to 21.8 cents per pound of magnesium are estimated for different versions of the process. Additional suggested process modifications are listed. The technical and economic potential of the different versions are compared. Areas deemed most promising for future research on the process are delineated.

Jan 1, 1967

These proceedings consist of an overview of the in situ mining research currently being carried out by the Bureau of Mines. The following papers emphasize two general aspects of the in situ mining method: the environment and productivity. Both areas are extremely important, particularly because in situ leach mining is a relatively new mining method from a commercial point of view. Topics covered include the restoration of ground water, the selection of lixiviants, in situ mining of commodities other than uranium, in situ mining costs, the application of resistance measurements to in situ mining, an acid leach mining case history, and the use of branched boreholes for in situ mining. A bibliography of Bureau of Mines publications on in situ mining is appended.

Jan 1, 1981

By Eugene T. Sheridan

The process of converting coal into coke is known as carbonization. Essentially, carbonization is destructive distillation in which the volatile matter of coal is released when coal is heated above its decomposition temperature and passes through a plastic stage before solidifying and forming coke. The mechanics of coke formation are complex, and the specific properties of certain coals that allow them to "cake" or form coke are still unknown. Coke is a hard, cellular, carbonaceous mass, formed by heating coal in the absence of air. It is porous, irregular in size and shape, and is similar in appearance to wood charcoal. Coke, however, is denser, more porous, and more abrasive than charcoal.

Jan 1, 1965

Our mission is help ensure our country has an adequate, dependable supply of minerals and mate al to meet its national security and economic needs at acceptable social, environmental, and economi[c] costs. We do this by promoting and encouraging private enterprise in the development of viable and stable mineral industries through the transfer of innovative extraction, processing, recycling, an environmental technologies; our use of cooperative partnerships with industry, academia, an government; our timely, authoritative worldwide mineral intelligence; our advocacy of public policies based on good science and sound economics.

Jan 1, 1994

This volume constitutes the Survival Subsystem portion of the final report for the Coal Mine Rescue and Survival System (CMR&SS) program, which was conducted by the Westinghouse Electric Corporation under contract to the United States Bureau of Mines (Contract Number H0101262 dated June 17, 1970). The program was directed by the Special Systems Department of the Westinghouse Baltimore, Maryland, facility. The basic objectives of the CMR&SS program were to develop and test hardware to determine the efficacy of a variety of coal mine rescue and survival concepts and techniques. These concepts were drawn from two major sources: the Request for Proposal from the Bureau of Mines1 and the final report on the Mine Rescue and Survival Study conducted by the National Academy of Engineering2 (NAE).

Jan 1, 1971