Search Documents

By Hugh Haddow

This paper describing the methods of recovery and treatment of a sand and gravel deposit and the preparation of these materials for a number of special markets is one of a series being prepared by the U. S. Bureau of Mines. It is of particular interest to those sand and gravel operators who have a surplus of fine sand which must be sent to waste, both from the point of view of, equipment and the variety. of markets supplied, and in that it describes one of the few sand and gravel plants which have resorted to hydraulic classification for sizing fine sand. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of J. R. Thoenen, mining engineer of the Bureau of Mines, in the preparation of this paper.

Jan 1, 1931

These proceedings consist of an introduction, nine descriptive papers, and a summary. The first paper is an overview of the respirable dust research program, the second paper describes the Mining Enforcement and Safety Administration's proposed changes in the respirable dust enforcement program, and the third paper describes respirable dust measurement. The remaining papers, by Bureau and contractor personnel, describes methods of reducing the amount of respirable dust to which coal miners are exposed. Of the six methods of reducing exposure to respirable dust described, two are methods of preventing or reducing the amount of respirable dust raised during mining operations, two are methods of collecting or removing dust after it has been released into the mine atmosphere, 2nd two describe methods that are combinations of prevention and collecting .

Jan 1, 1977

By John C. Franklin

Water-based epoxy sealants were examined during a 2-year period to deter-mine their effectiveness as barriers to radon release in uranium mines. Radon emanation rates from uranium ore samples were monitored for extended periods in the laboratory before and after sealant application. Reduction of radon flux due to the coating of laboratory samples was approximately 80 percent. Test chambers in a dormant uranium mine were monitored to determine both short and long-term barrier effectiveness. These field studies of the seal-ants indicated radon flux reductions exceeding 50 percent relatively soon after application and nearly 75 percent about 1 year later. An unexpected complication to early monitoring in the form of a large radon emanation increase, believed due to added moisture, is discussed.

Jan 1, 1977

By S. H. Ash

As part of the work done at the Washington coal mines during the year 1929 , a study was made of the safety practices in and about the mines . Inasmuch as electrical blasting has made considerable headway it is interesting to note the manner in which it is done and the reasons why it was discarded at some of the mines . Blasting is done at the mines in the State by means of capped fuse , electric blasting " caps , " and in some instances by electric delay detonators . Black blasting powder with fuse is used at most of the open- light mines . The use of squibs was discontinued several years ago because the coal operators , without exception , recognized the dangers incidental to their use . Permissible explosive and dynamite are also used at some of the open- light mines . With the exception of some rock work and the driving of level work in gangways and air courses the explosive is detonated by means of capped fuse .

Apr 1, 1930

By Mayo D. Hercey, Edward W. Butzler

"Purpose and Origin of Investigation.For many investigations of mineral products such as metallic and ceramic materials, especially refractories, a knowledge of thermal conductivity and specific heat at high temperature is required. Such data have been needed by the Bureau of Mines for checking heat balances in kilns, and computing heat loss through furnace walls.Design of apparatus for thermal conductivity tests was undertaken by the Bureau early in 1922, an industry at that time indicated that no equipment intended for extreme high-temperature observations was elsewhere available or likely to be in the immediate future.The Bureau's investigation was begun by C. R. Greenslade, assisted by F. A. Hartgen, and temporarily discontinued owing to their resignations in the summer of 1922. The work was later turned over to the writers of this report, and has been carried forward at intervals, along with other problems."

Jan 1, 1924

By Wm. W. Odell

For a number of years there has been a very appreciable annual,, increase in the production and recovery of natural gas and natural-gas gasoline2 in the United States the latter product being used largely for blending with gasoline from petroleum in the production of motor fuel. On account of the increased amount of oil cracking in the production of gasoline and the accompanying increased percentage of low-boiling constituents in the resulting product, the specifications for the natural gasoline suitable for blending have been altered, that is, the amounts of propane and butane which it can contain have been limited. The result has been that large quantities of the latter materials are wasted because there has been no ready market for thorn in large quantities. Because of this wasteage and because it is probable that large quantities of there and similar materials will be produced in the near future us a result of the more general use of oil cracking processes, a study was made by the Bureau of Mines, under a cooperative agreement with the assistance of the Phillips Petroleum Company, of the suitability of these materials alone or in mixtures for use as gas enricher in the carburetion of water gas for city distribution. This investigation included: (a) A study of the properties of the low boiling members of the paraffin series including pentane with particular reference to their utilization as gases.

Jan 1, 1927

By Thomas E. Lobb, Harry C. Verakis

Significant progress has been made in the reduction of serious injuries and fatalities resulting from mine blasting operations. Despite the progress, injuries and fatalities continue to occur. A leading cause of injuries and fatalities from blasting continues to be inadequate blast area security. Even though significant improvements in technology have been made, insuring adequate blast area security remains a challenge and requires constant vigilance. The advances in technology have created safer blasting products and have improved productivity and economics by enabling large, more efficient and effective blasts. However, as blasts grow larger in size, the complexity of adequately securing the blast area increases even more. Periodically the basic fundamentals involved in blasting safety should be reviewed, particularly for securing a blast site regardless of the size of the planned blast. Factors such as flyrock and toxic fumes must be taken into account to insure the safety of persons and property from the results of a blast. This paper examines the factors related to injuries due to inadequate blasting shelters and blast area security, and identifies mitigation techniques. The key concepts are: (a) accurate determination of the bounds of the blast area, (b) clearing employees from the blast area, (c) effective access control, (d) use of adequate blasting shelters, (e) efficient communications, and (f) training. Fundamentals are reviewed with an emphasis on analyzing task elements and identifying root causes for selected blasting accidents. Mitigating techniques are presented along with discussions and examples.

By L. C. IlsLey

Permissible blasting units are approved with the understanding that if actively marketed they will be listed as permissible so that all interested in such safety equipment may know what is available. The last detailed list of permissible units was published as Technical Paper 4294/. All of the blasting units of that list have become obsolete or have been modified as covered by extensions of the original approvals.

Jan 1, 1941

By Seth C. Schaefer

The Bureau of Mines investigated the standard Gibbs energies of forma-tion AGfo, for NiCr204 (nickel chromite) and CoCr204 (cobalt chromite). High temperature galvanic cells employing stabilized ZrOz (zirconia) as the solid electrolyte were used to measure the open-circuit potentials for the cell reactions ?

Jan 1, 1986

By Joseph A. DeCarlo

This information circular presents data for 1960 on individual coke plants in the United States. All oven-coke plants in existence, whether active or idle at the close of the year, are listed in this report. With two exceptions, only beehive plants on which reports were submitted to the Bureau of Mines are included. Although the Bureau was unable to obtain reports from these two active plants in 1960, the number of ovens and annual coke capacity are estimates, based on previous reports filed with the Bureau of Mines. Accordingly, there were 73 oven-coke plants in existence at the end of 1960 of which 70 were active. Reports were received on 44 beehive plants of which only 13 were in operation at year end. Oven-coke plants are listed alphabetically by States in table 1 which shows the name and address of the company, location of plant, classification or type of ownership, number and type of ovens, annual coke capacity, and coal-chemical materials produced. The terms "furnace" and "merchant" plants used in this and all other reports of the Bureau of Mines designate the type of ownership. Furnace plants are those owned by iron and steel companies whose main business is production of coke for use in their own blast furnaces. Merchant plants are those associated with chemical companies, gas utilities, as well as those that produce for sale on the open market metallurgical, industrial, and residential-heating grades of coke and coal-chemical materials. The annual coke capacity shown for each plant in this table is based on the minimum coking time necessary to produce coke with qualities suitable for its intended use. Therefore, the annual capacity of a plant may change from year to year, depending on age and condition of ovens, the character and quality of coal carbonized, the grade of coke required, and other factors. For example, annual coke capacity of a coke plant primarily making foundry coke with longer coking cycles would be lower than one making blast-furnace coke. Also some ovens must be operated at slightly lower than normal flue temperature because of the condition of the refractories and maximum capacity would be somewhat lower than designed capacity. For this reason, the capacity reported to the Bureau of Mines may differ from the designed or rated capacity estimated by the coke-oven builders at the time of construction. For example, if the generally accepted standard coking rate of one inch per hour were used on all ovens to calculate total annual capacity, it would have been 80.4 million tons or 2 percent higher than the capacity reported to the Bureau. Because of the factors mentioned above, the annual coke capacity shown in this table is believed to be a reliable measure of the practical operating capacity of the industry.

Jan 1, 1961

By Russell R. Trengrove

The Copper Canyon lead-zinc mine is in the Battle Mountain. District, Lander County, Nev. It was discovered in 1866 and mined for copper until 1935 and for copper and gold until l948, when the main production became lead-zinc ore. The rocks in the area are carboniferous (Pennsylvanian and Mississippian) sedimentaries that have been intruded by quartz monzonite of Mesozoic age. They have been intensely folded, faulted, and tilted. Lead-zinc ore occurs as sulfides disseminated along fractured zones in a conglomerate arid hornfels. Development was carried out by the Bureau of Mines in cooperation with the U. S. Geological Survey and comprised a study of the geology, making maps and. cross sections, and exploring the deposit by diamond drilling from underground. Eighteen holes were drilled, for a total of 2,594 feet. This report contains a brief history of the property and a description of mining methods and beneficiation of the ore, geology, ore deposits and drilling done by the Bureau of Mines. It also contains detailed analyses of the ore samples taken and logs of the holes drilled.

Jan 1, 1951

By Peter G. Kovalchik

To compare the viability of the new fuse wire arc test (FWAT) as a substitute for the comparative tracking index (CTI) for determining surface resistance to electrical tracking, the Bureau of Mines constructed a fuse wire arc tester and undertook a detailed testing program for testing insulating materials used on explosion-proof enclosures. This report describes the Bureau's apparatus, the two methods (CTI and FWAT), and the results of the Bureau's testing, showing comparisons of the FWAT with the CTI. Results showed strong correlation between the two methods, as all specimens tested that had CTI ratings of 400 V ac rms and above passed the 10-test sequence with the FWAT, whereas all specimens with lower CTI ratings failed, with the number of tests to failure corresponding roughly to the descending CTI rating order.

Jan 1, 1987

By F. P. Haver

The purpose of this investigation was to determine the effect of common impurities, that is, oxygen, nitrogen, carbon, and iron, on the Brinell hardness of electrolytic titanium. On a weight basis, nitrogen had the greatest hardening effect, followed by oxygen, carbon, and iron in order. The hardening effects of oxygen and carbon were almost identical up to a concentration of approximately 0.1 percent by weight. Above this concentration, the relative hardening effect of carbon decreased rapidly, possibly because of its limited solid solubility in a-titanium. Hardness vs. composition curves for both oxygen and nitrogen were essentially straight lines over the range of Brinell hardness numbers (B.h.n.) covered in the investigation. The hardness of titanium was also determined as a function of the percentage of impurity atoms. On this basis, iron in concentrations up to 0.17 atomic percent had a greater hardening effect than either oxygen or carbon. INTRODUCTION Determination of the as-cast hardness of arc-melted titanium is a method of quality control widely used in industry. Numerous studies4/ have been made of the effect of impurities on the hardness obtained by this method. However, most of them have been based on the use of either iodide titanium or commercially pure Kroll sponge (B.h.n. >90), as a starting material.

Jan 1, 1959

By W. A. Calhoun

A method for treating high-iron Arkansas bauxites for recovering both abrasive and metal-grade bauxite has been developed by the Bureau of Mines. Present practice usually produces a reject containing appreciable quantities of metal-grade bauxite; however, the processing renders the alumina in the reject unsuitable for the Bayer extraction treatment. Thus the Arkansas abrasive bauxite industry has, in the past, produced little or no metal-grade bauxite. The present investigation was made to determine the possibilities of batter utilization of those particular bauxites through recovery of the wasted metal-grade portion. The large expansion of aluminum-production facilities planned for 1951-53 makes recovery of metal-grade bauxite from presently treated abrasive and marginal abrasive ores en especially timely objective and a welcome addition to our aluminum potential. The quality of the Arkansas bauxites and the inherently associated titania content have made this material particularly attractive to the abrasives industry. however, the gradual depletion of natural abrasive-grade bauxite reserves in this area, the comparative scarcity of high-grade ore, and the difficulty of maintaining adequate reserves have necessitated blending different grades of bauxite calculated to meet specifications. Production of abrasive-grade bauxite from tile, high-iron reserves 13 becoming, increasingly necessary. In one commercial operation, producing abrasive-grade from ores averaging slightly less than 10 percent Fe2O3, approximately 2.7 tons of ore are required to produce 1 ton of abrasive-grade bauxite. The reserves of ore of this grade, however, have been considered inadequate for a long-range production, and ultimately ores averaging 12 to 15 percent Fe2O3 will have to be treated to moot the continued demands of the abrasive industry.

Jan 1, 1952

By W. M. Myers

The U. S. Bureau of Mines conducted an investigation to determine the cause of the deterioration of Portland cement during storage and transportation , and to discover a means of preventing it . All available printed sources of information on this subject have been examined and a bibliography has been compiled . The subject has also been discussed with the leaders in the cement industry ; the present report is the result of their cooperation , and is based principally on information thus obtained . Deterioration of Portland cement during storage over any considerable period of time has long been noted ; closely related to it is deterioration of cement during transportation, which involves not only the time factor of storage but also exposure to varied climatic conditions . Deterioration in both cases is due to hydration of the cement by absorption of moisture from a humid atmosphere , or by exposure to actual rain-fall . After hydration cement possesses no cohesive power ; the degree of deterioration is directly proportional to the degree of hydration . The amount of deterioration of Portland cement during storage has been accurately determined in an investigation by the Structural Materials Research Laboratory , in cooperation with the Portland Cement Association . Cement stored in a shed in cloth sacks retained 80 per cent of its original strength after three months storage ; 71 per cent after six months ; 61 per cent after one year ; and 40 per cent after two years . The deterioration of Portland cement during storage and transportation was noted particularly in France during the World War . Information concerning cement used by the American Expeditionary Forces was furnished by Lt. Col. H. S. Spackman and Major E. C. Eckel , U. S. R. , who had charge of practically all matters concerning cement used by the A. E. F. The cement used by the A. E. F. came from the following sources : 42,000 tons was French , Swiss , and Spanish cements ; 120,000 tons was English cement ; 55,000 tons made in plants operated by the A.E.F .; 500 tons ( Not over) from America . Deterioration was most marked in cement from the first source .

Jun 1, 1922

By A. C. Burr

This progress report summarizes operating results on the gasification of natural lignite from five runs of the commercial-scale pilot plant at Grand Forks, N. Dak., during December 1946 and calendar years 1947 and 1948, when the plant was operated for 1,996 hours. A primary specific objective was to determine the useful life of the outer metal retort tube as it is influenced by corrosion and other factors under a wide range of operating conditions. A secondary objective was to develop the technology of production when generating gas with a high ratio of hydrogen to carbon monoxide in both the divided and continuous annuli. Results are summarized in graphs and tables that show hydrogen-carbon monoxide ratios from 2.3 to 9 at gas-production rates from 6 to 12 M cu. St. per hr. (thousand cubic feet per hour), or approximately 30 to 60 cu, ft. per square foot of heated retort-wall surface per hour. Gas yields ranged from 36 to 54 M cu, ft. per ton of natural lignite or 63 to 91 M cu. ft. per ton of moisture- and ash-free lignite, Production rates were higher in the divided annulus, but these represent the maximum capacity of the plant only at high hydrogen-carbon monoxide ratios when the high concentration of excess steam and low furnace temperature limit gas production. A ratio of 6 was the highest produced in the continuous annulus because mechanical Limitations of the auxiliary equipment prevented attainment of higher ratios. The lignite feed rate appears to influence the production rate more than any other individual operating variable. Heat balances for four periods when gas with ratios from 2.3 to 7.2 was produced with a lignite feed rate of about 325 pounds per hour suggest that the potential heat in the gas is lower at higher ratios, owing to increased heat losses in the excess steam. Heat-transfer rates through the retort tube in these four tests were between 1,500 and 3,000 B.t.u. per square foot per hour. These rates are much lower than those reached in many earlier tests, but no attempt was made to achieve maximum rates of heat transfer.

Jan 1, 1953

By G. Nuñez, M. A. Pathak, A. A. Afshari, C. F. Stanley

"To help evaluate the vibration patterns of an excised lung, a method is developed to determine which parts of the surface of an excised lung are responding to acoustic excitation via the trachea. Holographic interferometry, a very' sensitive technique ·that can measure movements of a few microns, is used to detect the lung surface movements.The intact lung and heart are excised from Long· Evans male rats weighing 250 gm. A tube is inserted into the trachea and connected via a funnel to a 3 inch cone speaker. The assembly is positioned in the holographic unit and excited at frequencies up to 10,000 Hz. The holographic unit contains an acousto-optic shutter used with a 0.5 watt Argon laser.The resulting reconstructed holograms contain interference fringes that are indicated of lung surface vibration.INTRODUCTIONA 1986 report by the U.S. National Committee on Biomechanics [1] describes diseases of the lung as a major national health problem. One of the recommendations of the report is for continued study of the mechanical properties of lung tissue. As an example, the report cites at least three areas that would benefit from a better understanding of the vibratory patterns or the lung."

Jan 1, 1989

By R. V. Higgins, A. J. Leighton

A computer program has been devised to calculate the reservoir performance of water floods of complicated well - spacing patterns . The method and program have been tested by calculating the waterflood performance of fivespot patterns using oils of different viscosities and the performance calculations agreed closely with laboratory results . The program on a high - speed digital computer will process the performance prediction in about 1 minute , which is very rapid for a prediction using so much fluid mechanics and nonlinear geometry . The program has been presented in such a way that one may use it as given and save the time required to write and " debug " one of his own . gram processes a complex reservoir analysis , many of the complicated steps are explained in detail , both for the fluid mechanics and the directions for the computer . The subtle features that originally delayed the application of the program to unusual combinations of permeability and viscosity relationships are incorporated and explained

Jan 1, 1963

By Selim E. Woodworth

This paper, describing the milling practice on the Mother Lode as typified in the mill of the Argonaut Mining Co. at Jackson, Amador County, Calif., is one of a series prepared by the United States Bureau of Mines. The data herein presented and furnished through the courtesy of E. A. Stent, managing director and vice president of the Argonaut Co., covers operations from 1914 through the year 1929.

Jan 1, 1931

The principal activities of the Bureau of Mines Explosives Research Center from July 1, 1963 to June 30, 1964 are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1964; in general, the research reported in these publications antedates the report period. Part 3 describes a short-term investigation into safety problems associated with shipping of molten sulfur; this investigation is not at present destined for publication elsewhere.

Jan 1, 1965