Search Documents

By J. W. Paul, A. C. Fieldner

"In cooperation with the New York and New Jersey State Bridge and Tunnel Commissions, the Bureau of Mines has just completed the construction of an experimental tunnel in the Bureau's experimental mine at Bruceton, Pa., near Pittsburgh, Pa. The purpose of this tunnel is to make a final study of the ventilation problems arising in the adequate ventilation of vehicular tunnels for automobiles and trucks, especially the 9000-foot tubes that are being designed. to handle the traffic between New York City and New Jersey under the Hudson River.Chief engineer, Clifford M. Holland, of the Tunnel Commissions has shown that there are three principal problems involved in planning the ventilation of this tunnel, namely - (1) The amount and composition of exhaust gases from motor vehicles; (2) The dilution necessary to render these exhaust gases harmless; (3) Determination of coefficients of airflow and horse-power required in ducts, bends and openings.Composition of automobile exhaust gases.The answer to the first problem was obtained by making road tests on 101 automobiles and trucks at the Pittsburgh experiment station. These machines were taken from service without any previous adjustment so that the composition and amount of the exhaust gas may be taken as representative of actual operating conditions prevailing in the tunnel. A report covering the results of these tests was submitted to the chief engineer of the Tunnel Commissions, on November 1, 1920, and 411 be published in the report of the commissions. Several papers a have also been published in the technical journals summarizing the important results as regards tunnel ventilation and also with reference to gasoline losses in present-day motor car operation due to the general use of unnecessarily rich mixtures"

Oct 1, 1921

By Robert G. Lundquist

The Bureau of Mines compared longitudinal strain energy output of a percussive drill to energy determined by measuring maximum piston velocity. Strain gages were used to determine the strain-time waveform and its amplitude at seven levels of operating pressure and eight levels of thrust. The longitudinal strain energy was found to be approximately 14 ft lb less than the maximum piston energy at comparable operating conditions.

Jan 1, 1969

By Ivette E. Torres

Many significant events that began in 1990-91 continued to have a profound impact in the world minerals economy in 1992. The dissolution of the U.S.S.R. and the formal breakup of the Council for Mutual Economic Assistance (CMEA) had significant effects far beyond the geographic boundaries of Europe and Central Eurasia. CMEA's network of economic interdependence had relied on central planning, a variety of subsidies, and barter agreements that allowed its members to function without the pressures of productivity and efficiency. In the mineral sector, many decisions had been made based on the need for military planning and technology competition with the market economy world. Because of inexpensive oil available through subsidies and technology assistance from the former U.S.S.R., industries III CMEA member countries had been able to function and maintain production to supply minerals and materials required to support the policies of the central plan. In 1992, most of the former CMEA countries decreased their output of many minerals. In some cases, the network of production that had been in place was severed. Political and economic instability, destruction of infrastructure, and new priorities were affecting other mineral industries in the area. In late 1991, 15 independent countries replaced the U.S.S.R. and in early 1991 the former CMEA countries found themselves trying to adjust to the realities of economic independence and the need to compete with former allies for survival. Although 11 of the 15 former Soviet republics joined in the Commonwealth of Independent States (CIS) in December 1991, in 1992, individual economic needs exceeded the needs of the Commonwealth III importance. As a result, new mineral trade patterns emerged as minerals were used as a source of much needed capital.

Jan 1, 1994

In Bureau of Mines research on recycling chrome refractory wastes, used refractories from argon-oxygen decarburization and electric steelmaking furnaces were beneficiated, concentrates were reformed into briquets, and modulus of rupture tests were conducted at 1,350° C. The test results indicated that the beneficiated minus 6-mesh material could be used for producing magnesia-chrome refractories.

Jan 1, 1980

By T. F. Morse, R. Lundstrom, A. J. Brammer, D. Peterson, M. Cherniack, T. Nilsson, J. D. Meyer, E. Toppila, G. Neely, N. Warren

HAVIC is a collaboration of investigators from North America, Sweden, and Finland having a scientific mandate from NIOSH, to study the exposure response relationship between vibratory tool exposure and adverse health effects. Five cohorts, the Suomossalmi forest workers cohort, Volvo truck cab workers, Connecticut shipyard workers, and matriculating dental hygiene students and experienced dental hygienists have been under study. In the case of shipyard workers, there was survey and tool exposure data from 1988, although detailed subject testing was only available within the timeframe of the study. The truck cab assembly workforce was an inception cohort that had been followed from 1994 along with age-matched controls. The Finnish forest workers had cumulative health data on a cohort (n=52) that had been studied from 1976. For a subset of these subjects, there was detailed tactometry testing in 1990, 1995, and 2003. Accordingly, there was historical as well as new prospective data for the industrial cohorts. The Suomossalmi cohort was reassembled only for our study, which precluded follow-up evaluation and because of retirement is almost certainly the last time this historic group will be studied. The study features are: • Characterization of the exposure response relationship for hand-arm vibration through a study design, incorporating multiple cohorts, some having existing historical data, • Selection of cohorts to include different types of vibration: oscillatory (forest workers) impact (truck cab workers), high frequency (dental hygienists) and mixed (shipyard workers), • Inclusion of two inception cohorts: dental hygiene students and Swedish truck cab workers, • Methods for multi-site and historical integration A description follows. [ ] Methods The study included surveys, physical evaluation, and a selection of battery of “best tests” (cold challenge plethysmography, multi-frequency tactometry, segmental sensory nerve conduction velocity [SNCV]1,2,3) applied across groups to quantify responses to exposure. Exposure monitoring included exposure characterization through daylong data logging at the individual level. Workers at each site were instrumented with a microcomputer-based Vibration Exposure Monitoring (VEM) system, developed at the Biodynamics Laboratory of UCHC and about the size of a police walkie-talkie, to record user-specific tool-operating times, vibrations, and grip forces throughout all, or a representative part, of their workday. More specifically, data logging methods involved the direct monitoring of work cycles, involving tool operation time and measures of tool vibration, namely the root-mean-square (RMS), root-mean-quad (RMQ), and root-mean-oct (RMO), and grip forces, each calculated per minute. For this study, the questionnaire was homogenized with other vibration studies4,5,6. Cross-translation was directed by the multi-lingual investigators, and then reviewed by the study team. To extend comparability with future international studies, questions were also added from the Vibration Network (VINET) draft questionnaire, the product of a European

Jan 6, 2006

By Jack Wasserman, Don Wasserman, Logan Mullinix, Shekhar Khanal, Kelly Neal

This paper presents current finding on truck driver average exposure to acceleration for several different manufacturer’s cab-over trucks on a variety of roads in different countries. The predominant time, for this aspect of the study has been spent in the area around London, England and Warsaw, Poland. The ECE directive 2002/44/EC has provided specific guidelines for vehicle operators 8 hour average acceleration exposure. The primary considerations have been on truck design including the air-ride driver’s seat. The truck manufacturers have produced truck cabs that have some separate suspension from the truck frame. The truck seat manufacturers have been producing air-ride suspension seats for the cab. Both of these designs have had the objective of meeting the ECE directive and providing the vehicle drivers with some degrees of comfort. This paper will provide some information on the ability of the vehicles to operate on a variety of roads and meet the objectives. Method The primary method for evaluation of the driver’s exposure has been the use of a seat pad attached to the driver’s seat. Although this sensor system provides the critical information for the driver, an understanding of the reasons for the values requires additional measurements. The initial study in England used both driver and passenger seat pads, as shown in Figure 1, as well as triaxial accelerometers mounted on the base of the seat. The latest studies used significantly more transducers to better understand the relative rotations and translations on the truck frame, the cab, and the driver. [ ]

Jan 6, 2006

By David C. Grant

A laboratory technique for simulating in-situ uranium mining was developed and used to determine the effects of leaching variables on permeability, uranium recovery, leach solution interaction with the ore-aquifer environment, and post-leach chemical leakage. In particular, ammonium bicarbonate, the commonly-used leach solution, was examined in great detail. Agitation leach tests were conducted to examine the effect on ammonium sorption and desorption of clay content, solution and clay ammonium levels, pH, and the type and concentration of other anions and cations in solution. Initial column tests were performed to determine the degree of ore-aquifer interaction that could be expected for various leach solutions; sulfuric acid, and ammonium, sodium, and potassium bi-carbonates. Subsequent tests examined various methods to restore the ores by lowering the post-leach chemical leakage. The restoration tests examined the use of reducing agents (e.g., ammonium bisulfite, sodium bisulfite; and sodium sulfite), ore blocking and stabilizing agents (e.g., sodium silicate, aluminum chloride, and magnesium-calcium salt).and ammonium displacement agents (e.g., aluminum chloride and lanthanum chloride-sulfate)

Jan 1, 1980

By Thomas L. Theis

The use of a suspended growth system of T. ferrooxidans attached in a film to individual particles of bentonite and operated as a sequencing batch reactor has been shown to be a practical way of oxidizing ferrous iron in acid mine drainage. This component followed by limestone neutralization is both a technically and economically feasible approach to the treatment of these wastewaters in comparison to existing and proposed methods. The advantages, in addition to less expense, are greater safety, acceptable treatment at a lower pH, lower solids buildup, less danger of overtreatment, and greater flexibility in operational characteristics. In this report data on the continuous bench scale operation of the system under a variety of conditions shows sustained levels of oxidation in excess of 9%. A cost analysis projects capital and operating costs of $80/1,000 m3 of wastewater.

Jan 1, 1982

By Thomas E. Doerfler

Information and data related to the occurrence of fatalities due to major disasters in metal/nonmetal underground mines were analyzed. Standard statistical methods were used to estimate the probability of occurrence of major disasters, and to examine the relationship of disasters to injury statistics published annually.

Jan 1, 1980

By D. O. Kennedy

THIS CHAPTER on minor nonmetals covers greensand, meerschaum, mineral wool, and wollastonite. Mineral wool was by far the most valuable material among these minor nonmetals reported in the United States in 1956. GREENSAND Output of greensand (glauconite) declined in 1956. The Kaylorite Corp., Dunkirk, Md., and the Inversand Co., Sewell, N. J., were the only firms that reported production of this commodity. Output came from open pits in Calvert County, Md., and Gloucester County, N.J.

Jan 1, 1958

By Gary Choate

The work presented in this report represents the background activity which led to the fabrication and testing of a greenhorn and crowd limit switch system for electric shovels. The program began With a literature search and manufacturers product review to gather material as a basis for concept generation. Visits to three open pit mines provided information from operation and maintenance managers which was useful in preparing design concepts. These concepts were evaluated through laboratory tests and engineering analysis to select a final design concept. The resultant greenhorn is four separate shock absorbing pads each enclosed in a housing which bolts to the end of a dipper handle adaptor. The plungers impact against stops mounted to the saddle block. The crowd limit control is a nonmechanical device which senses the location of the dipper and makes appropriate commands to the crowd motor to insure against impacting the greenhorns. The electronic crowd limit control is redundant and indicates malfunction modes. The greenhorn prevents shovel damage in the unlikely event of impact.

Jan 1, 1983

By John G. Parker

Important quantities of gold, silver, platinum-group metals, selenium, tellurium, and arsenic are recovered in the processing of copper concentrates. The objective of this Bureau of Mines study was to determine the occurrence of these elements in copper ores and to trace their distribution during subsequent processing steps. The study describes the important areas supplying concentrates, precipitates, and unrefined copper to the copper smelting and refining industry in a composite of the years 1971-74. The relative importance of these areas as a source of the respective byproducts is assessed. The lack of certain quantitative and assay data, recycling of dusts and slags, and the addition of scrap to the feed often complicates calculations and estimations of the byproducts in the smelter-refinery throughputs. Such volatile or low-boiling point elements as arsenic, selenium, and tellurium may be lost in gaseous and other emissions in various processing stages, or they may be concentrated in slags and residues for which samples were not available. The effects of antipollution legislation to improve control of sulfurous and other emissions that may affect recovery of certain byproducts was noted. A section on newer technology illustrating hydro-metallurgical techniques that may affect the recovery of minor metals is included.

Jan 1, 1978

By P. Delogne, L. Deryck, R. Liegeois

So far as the propagation of electromagnetic waves is concerned, an underground tunnel behaves like a pipe or hollowed waveguide. Waves propagate in this tunnel with a low attenuation only if their frequency is higher than a so-called critical frequency which depends on the shape and mostly on the cross -dimensions of the tunnel and which value is in the neighbourhood of several tenths of MHz. However, when a metallic conductor is stretched along the gallery the electromagnetic characteristics of the latter are considerably modified and the effect of the cut-off frequency disappears; this is due to the fact that the gallery equipped with such a conductor works like a coaxial cable where the conductor serves as the outward conductor and the wall of the gallery as the return conductor. This is the principle of the monofilar waveguide cable which has been perfectly studied by Gabillard. Two mean characteristics of the monofilar mode are as follows: first of all, when the cable is suspended in the middle of the cross section of the gallery, the electromagnetic field occupies all the space between the wire and the walls of the gallery. When the wire is close to the wall, the electromagnetic field tends to become concentrated between the wire and the wall, with the consequence that, with the given monofilar mode power, the aerial of a receiver standing somewhere in the tunnel will capture a weaker and weaker signal. Secondly, owing to the fact that the mode of monofilar propagation uses the ground as return conductor, its power of propagation is considerably diminished; the closer the wire is to the wall the higher the attenuation, for only a very small part of the wall is utilized as return conductor. To cover great distances, everything else being equal, two or more conductors must be placed in the gallery. If the distance between two conductors of a cable is much smaller than the distance between one or other of the conductors and the walls; or again if one of the conductors surrounds the others and forms a screening, two sorts of modes appear: on the one

Jan 1, 1973

By R. V. Ramani, P. M. T. White, D. Sutton

6.1 Summary This report deals with the investigation carried out to select, test, and implement a method of evaluating coal deposits and reserves. Cognizance is taken of the inherent characteristics of coal and the legislation covering aspects of health, safety, environment, and ecology applicable to the coal mining industry. Further, the method is computerized and provides information that is meaningful and readily available to other programs and sub¬systems within the concept of the Master Design Simulator. The Geology and Reserves Sub-system interface with the total system is provided by a geological data library which is structured to hold and make accessible all the data required by the system. The output from the program is accurate and useful to users with a wide variety of computer experience, knowledge, hardware and storage capacity. The sub-system is designed to function as a separate unit or an integral part of the total system and, there¬fore, an interface to or with the system has been established. The work carried out by the sub-system includes: (a) The analysis of raw geological data. This involves:

Jan 1, 1974

By R. E. Heithecker

In Kansas, almost every oil well drilled into a limestone formation is treated with hydrochloric (muriatic) acid upon completion. This is done to increase the potential capacity of the well and thereby increase its "daily allowable" production (see p. 9 ), to shorten the time required to produce the recoverable oil, and to increase the quantity of oil recovered ultimately from the reservoir. The porosity and. permeability of limestone formations seldom are uniform throughout the proved area, consequently the production capacities of completed wells vary considerably. Acid treatment of wells tends to increase production capacity and to equalize potential capacity. If offset wells already have been treated with acid, new wells usually are treated to protect the property on which they are drilled against drainage. Even though competitive conditions do not exist in a field, it

Jan 1, 1939

By R. V. Ramani, A. S. C. Owili-eger

? THIS PROGRAM SIMULATES METHANE FLOWRATES THROUGH THE GOAL ? SEAM BY THE GAUSS-SEIDEL ITERATIVE TECHNIQUE. THE MODEL IS A TWO ? DIMENSIONAL SYSTEM. THE ITERATIVE FORM OF THE GAUSS-SEIDEL IS ? OBTAINED FROM A PARTIAL DIFFERENTIAL EQUATION OF FLOW BY CENTRAL ? FINITE-DIFFERENCING APPROXIMATION SCHEME ? NPRESS IS THE NUMBER OF SPECIFIED PRESSURES EXCLUDING ? RESERVOIR AND FACE PRESSURES ? NQUAN IS THE NUMBER OF SPECIFIED FLOW QUANTITY.... EXCEPT FLOW ? OUT OF THE FACE. THIS- QUANTITY CAN BE POSITIVE(INJECTION) OR ? NEGATIVE ( PRODUCTION) ? XPERM(I,J) I S THE DIRECTIONAL PERMEABILITY IN THE X-DIRECTION AT THE POINT (I,J) ? YPERM(I,J) IS THE DIRECTIONAL PERMEABILITY IN THE Y-DIRECTION ? AT THE POINT (I,J) ? RESEP' IS THE RESERVOIR PRESSURE ? FACEP IS THE FACE PRESSURE. THIS PRESSURE IS ASSUMED TO BE ? APPROXIMATELY ATMOSPHERIC ? LENGTH, WIDTH, AND THICK ARE THE ZONE OR MEDIUM DIMENSIONS * PUHL I S A DUMMY NAME FOR VISCOSITY ? DMAXI IS VARIABLE NAME FOR INITIAL MAXIMUM ERROR OF ITERATION ? DMAXF IS A VARIABLE NAME FOR FINAL MAXIMUM ERROR OF ITERATION ? NITER IS A VARIABLE NAME FOR STORAGE OF NUMBER OF ITERATIONS ? RAD IS A VARIABLE NAME FOR THE SPECTRAL RADIUS OF THE GAUSS¬ ? SEIDEL MATRI-X. THIS PARAMETER ALSO MEASURES THE RATE OF ? CONVERGENCE OF THE ITERATION ? KOUNT IS AN ITERATION COUNTER ? MAXIT IS THE MAXIMUM NUMBER OF ITERATION SPECIFIED BY THE USER # EPS IS THE MAXIMUM RESIDUAL ALLOWABLE ERROR-FOR CONVERGENCE

Jan 1, 1974

By Phillip R. Moyle

A cobalt/manganese occurrence in Clark County, Nevada was the subject of a site-specific mineral investigation by the U.S. Bureau of Mines in 1988-90. The study site is in the northern part of the Million Hills (wilderness) study area which is administered by the Bureau of Land Management. Field work during a period of one week consisted of geological mapping and sampling of workings and outcrops, and geochemical and geophysical surveys conducted on four transects totalling 7,600 ft. Although the concentrations of cobalt (0.1 to 0.5 percent) detected in samples from the fissure zones are within the range of grades associated with world-class economic deposits, the volume of material enriched in cobalt at the study site is insufficient to warrant consideration as a potential resource. Concentrations of manganese, nickel, copper, lead, zinc, barium, and thallium, although anomalous, are too low for economic consideration. At the study site, workings consist of three trenches and nine pits. The exploration history is unknown, and no production is reported.

Jan 1, 1990

To improve a miner's chances for survival in an emergency by providing an improved self-rescuer device that functions in a toxic or oxygen-deficient atmosphere. The Approach: Development of a compact, lightweight apparatus which produces oxygen by using the wearer's breath in a chemical reaction. How It Works: The device is designed to cause the user's breath, which contains water vapor and carbon dioxide, to react with potassium superoxide (K02) to produce oxygen in quantities sufficient to sustain the wearer for one hour. The system is a closed circuit and does not depend on "screening" of noxious gases. To use the device, the miner opens the top and

Jan 1, 1974

By Kay E. Goldberg

The Bureau of Mines conducted a study to develop and evaluate a training workshop for mine safety training personnel. The workshop was based on the Instructional Development Institute (IDI) which has been used for nearly ten years to train educators and administrators in the application of a nine-step model for defining, developing, and evaluating instruction. The Mining Instructional Development Institute (MIDI) was developed by investigators at the University of Southern California as a two-phase project. Phase I involved the modification of the six-day IDI program (including audiovisual presentations, workbooks, games, and exercises) for use by mine safety trainers as a workshop lasting three and one-half days. Phase II involved the evaluation and validation of the prototype MIDI workshop by means of a two-stage jury of experts and a prototype field trial. On the basis of data collected in the validation process it was determined that the institute provided an effective and useful method of instruction in mine safety training and that the institute would be especially valuable for mine safety training administrators and supervisors.

Jan 1, 1980

By Peter Kovalchikb, Gregory Colec, Syd Peng, R. J. Matetic, Jeffrey Petersond

Mine Safety and Health Administration (MSHA) data indicates that the roof bolting machine is third among all equipment and second among equipment in underground coal mining whose operators exceed the MSHA-PEL (Mine Safety and Health Administration-Permissible Exposure Limit). In response to this, the National Institute for Occupational Safety and Health (NIOSH) has conducted a study to reduce overexposures of noise to operators of roof bolting machines. An important segment of the research is to determine, characterize and measure sound power levels radiated by a roof bolting machine during different drilling configurations. The determined sound power levels generated during the drilling cycle are of major interest because the levels represent the overall sound power generated by the machine. These sound power levels, determined from laboratory tests, can be used to accurately assess the effectiveness of proposed controls for reducing noise exposure to roof bolting machine operators. By using the sound power level results obtained from the laboratory and a commercially available acoustical modeling package, a method for predicting sound pressure levels to roof bolting machine operators for differing drilling types and parameters could be determined. This paper provides a method for predicting sound pressure levels at the operator’s position of a roof bolting machine in an underground coal mine using sound power levels determined in the laboratory. To determine validity, underground coal mine data was also collected to compare predicted and measured sound pressure levels. The results of the predicted sound pressure level data were the same as the underground measured results. This research will provide the mining industry with a valid method for predicting a roof bolting machine operator’s noise dosage underground given any type of drilling configuration or drilling method utilized from laboratory testing.