Search Documents

By Forrest T. Moyer

General injury experience in the mineral fuel industries was less favorable in 1965. Of the major industry groups, the coal mining and the coke industries had higher injury-frequency and severity rates than in 1964. The oil and gas industries had an increased Tate of occurrence of injuries although the severity rate improved. However, in the relatively small peat and native asphalt industries, the injury experience was more favorable than in 1964. Overall operating activity for the mineral fuel industries, as measured by the average number of men working daily and the total worktime, was higher than in 1964. Moderate declines in employment and worktime in the coal and peat industries were more than offset by gain in the other groups. In addition to the industry classifications included in this chapter, similar injury, employment, and worktime data on the metal, nonmetal, stone and aggregate industries are presented in volume I. Corresponding data for broad classifications of mineral industry groups arc given by States in volume III of the Minerals Yearbook.

Jan 1, 1967

By F. M. Goodwin, Campbell. John, W. J. Hiffs, G. W. Jones

"INTRODUCTION In cooperation with The Edison Electric Illuminating Co. of Boston, Mass., and the Boston Consolidated Gas Co. a survey has been conducted continuously since 1929 by the United States Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes of the Edison Electric Illuminating Co. The New England Telephone & Telegraph Co. also has cooperated in the investigation, and tests have been made in its manholes since May 1, 1933.Yearly reports 6 giving the results obtained since the start of the survey have been published.The method and procedure of conductin, the survey in 1935 were the same as heretofore.ACKNOWLEDGMENTSThe cooperative investigation was arranged through the interest and effort of F. D. Comerford, president of the Edison Electric Illuminating Co. of Boston; E. N. Farnesworth, Jr., vice president and general manager of the Boston Consolidated Gas Co.; and A. C. Fieldner chief engineer, Experiment Stations Division, U. S. Bureau of Mines. Thomas H. Haines, superintendent, Distribution Department, of the Edison Electric Illuminating Co., cooperated in furnishing men and information for the work,"

Oct 1, 1936

By Francis E. Federspiel

Silver and gold are the principal metals in the study area; they occur in quartz veins or silicified portions of shear zones. In some deposits, lead, antimony, zinc, and molybdenum are associated with gold and silver. A uranium-bearing buried stream channel lies near the southern boundary. Since 1850, more than 300 lode claims and relocations have been recorded mainly in the southeast corner of the study area (fig. 1). Complete mine production records are not available; however Clark (1977, p. 28) reported less than $300,000 of gold and silver were produced, mainly from the Exchequer, IXL, and Pennsylvania Mines. Other mines in the area probably yielded are before 1900, but early records are not available.

Jan 1, 1981

By E. G. Valdez

Iron foundries that melt automobile scrap produce flue dusts averaging about 32 percent zinc and 6 percent lead. Some is sold to smelters, but because of the meager return and difficulty in handling, most of the dust is discarded. As part of the Bureau of Mines program to find uses for mineral wastes, research was initiated to develop an economical process to recover zinc and lead from the flue dust. Research encompassed the extraction of zinc and lead by fuming, leaching, and agglomeration. Controlled vacuum fuming of zinc to produce Prime Western zinc and a lead-rich residue was the most effective method for treating the dust. This process involved two distillations, or fumings, with carbon and methane as reductants, and resulted in recovery of 91.4 percent of the zinc in a Prime Western grade product, and 98 percent of the lead. Hydrometallurgical techniques involved several leaching methods, but the simultaneous extraction of iron, manganese, and copper resulted in contamination of the solution and made the zinc recovery processes too complicated. Agglomeration was done by pelletizing or briquetting the dust for possible use as feed to a zinc smelter.

Jan 1, 1975

By Virgil A. Marple

The objective of this contract was to investigate time-integrated and real-time methods for determining the diesel exhaust particulate concentration in underground mines, in particular, coal mines. The microorifice uniform deposit impactor (MOUDI) is recommended for obtaining the time-integrated measurement of the size distribution. The mass concentration of diesel exhaust particles can be obtained from the particle size distribution of mine aerosols. On a mass basis, diesel exhaust particles are primarily in the submicrometer size range while coal dust particles are larger. Size distribution measurements made in the laboratory and in three underground coal mines exhibited two distinct modes with the diesel exhaust particles in the smaller particle mode and the coal particles in the larger particle mode. The point of separation between the two modes occurred in the 0.7 to 1.0 pm size range. The separation was found to be independent of mass fraction of the diesel exhaust particles, particle concentration and sampling site. Methods recommended for further consideration as real-time monitors of diesel exhaust aerosols in mines are photometers and filter pressure drop techniques. A preclassifier would be required in both cases to separate the larger dust particles from the sample. The Metrex Mineral/Diesel Photometer should also be investigated further once the electronics problems are eliminated.

Jan 1, 1986

By David L. Bickel

The following instructions and descriptions are presented in two parts to assist an individual to make the borehole deformation gage transducer, and to assemble and test the three-component borehole deformation gage. This Bureau 8 of Mines three-component borehole deformation gage (4, 8, 11)2 fits in a 1-1/2-in-diameter borehole that is drilled in rock and then overcored to determine rock stress.

Jan 1, 1978

By V. F. Parry

[Subbituminous coal or lignite when stored in random piles or in ordinary bins in which the temperature fluctuates and air circulates quickly undergoes objectionable physical and chemical changes, which decrease the utilization value of the fuel and increase its tendency to ignite spontaneously. Slacking takes place, and the heating value decreases. These changes are accelerated by fluctuations of temperature and by circulation of air through the storage space. When such coals are exposed to the weather they lose moisture rapidly. If evaporation from the surface of a lump proceeds at a faster rate than that at which it is replaced by moisture from the interior, the rate of shrinkage at the surface is greater than that at the interior; consequently, stresses are generated at the surface which cause the coal to disintegrate. Likewise, when moisture is absorbed by the air-dried surface the outside layers expand at a faster rate than the interior, which results in further break-down. As these cycles are repeated the lump may disintegrate completely. Therefore, successful storage of low-rank coals depends on control of the factors that influence change of moisture.]

Jan 1, 1941

By David C. Oyler, Winton J. Gale, Jinsheng Chen, Christopher Mark

A collaborative project between RAG Emerald Mine, NIOSH, and SCT Operations was conducted to investigate ground behaviour, reinforcement performance, and stress redistribution in a coal mine entry subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8 m (16 ft) above the entry. This paper focuses on the computer simulation that was undertaken to provide more insight into the roof behaviour and rock bolt interaction during mining. The model’s input rock properties were derived from extensive laboratory testing, and the model itself simulated a broad range of failure mechanisms. The effects of different bolt patterns on roadway behaviour were evaluated. Comparison between the model results and the field measurements indicated that that the model effectively simulated the critical elements of the actual roadway’s behaviour. With the confidence gained, the model was used as a baseline for additional simulations that evaluated the expected performance of alternative roof support systems. The study will also provide a benchmark data set for future applications of numerical modelling to U.S. coal underground mining.

By Frank E. Federspiel

In 1986 and 1987, at the request of the U.S. Forest Service, the U.S. Bureau of Mines examined the 47,000-acre Electric Peak study area (part of the formerly-designated RARE II Non-wilderness Recommended Area no. 1609) to evaluate its' identified mineral resources. The study area is in Powell and Jefferson Counties, YT, about 30 mi southwest of Helena and 30 mi north of Butte. Three lode localities within the study area contain an estimated 159,000 tons of identified subeconomic resources containing gold, silver, and accessory lead, copper, and zinc. Resources at those localities range from 10,000 to 134,000 tons with grades ranging from 0.04 to 0.32 oz/ton gold, 0.92 to 16.42 oz/ton silver, 0.14 to 79.65 percent lead, and as much as 0.41 percent copper and 0.68 percent zinc. One property also contains 0.15 percent antimony. Gold, silver, and base-metal content in samples of poorly exposed mineralized structures indicate that further exploration may identify resources on seven additional study area localities.

Jan 1, 1988

By V. F. Parry

Subbituminous coal or lignite when stored in random riles or in ordinary bins in which the temperature fluctuates and air circulates quickly undergoes objectionable physical and chemical changes, which decrease the utilization value of the fuel and increase its tendency to ignite spontaneously. Slacking takes place, and the heating value decreases. Those changes are accelerated by fluctuations of temperature and by circulation of air through the storage space. When such coals are exposed to the weather they lose moisture rapidly. If evaporation from the surface of a lump proceeds at a faster rate than that at which it is replaced by moisture from the interior, the rate of shrinkage at the surface is greater than that at the interior; consequently stresses are generated at the surface which cause the coal to disintegrate. Likewise, when moisture is absorbed by the air-dried surface the outside layers expand at a faster rate than the interior, which results in further break-down. As these cycles are repeated the lump may disintegrate completely. Therefore, successful storage of low-rank coals depends on control of the factors that influence change of moisture.

Jan 1, 1941

By Robert W. Decker

This report presents a survey of published novel coal cutting (mining) concepts and a brief discussion of each one. A preliminary evaluation follows which identifies promising concepts, emphasizing reduced dust generation and economic production potentials. The promising concepts are then studied more deeply and evaluated in more detail with recommendations given for further development action. The concepts recommended for further work include: Roan and Pillar Mining: Deep Cutting Continuous Miner Linear Cutting Rotary Head Miner Longwall Mining: Oscillating Continuous Water Jet Miner Deep Cutting Shearer

Jan 1, 1981

By R. H. Sprute

Underground accumulations of slimes in the Henderson mine are routed to two large collection pits where they are dewatered and consolidated by application of direct current. Densified material is then removed to ore cars by rubber-tired front-end loaders and transported out of the mine. This Bureau of Mines report describes the electrical dewatering installation and compares its efficiency of operation with that predicted from preliminary laboratory studies performed by the Bureau. Direct current from a 150-kw rectifier (applied for 44 hours at 400 amperes and 65 to 70 volts) converted slimes containing 25.3 percent solids to material ranging from 44 to 65 percent solids. Better results can be expected if the ramp and front sections of the pits are treated separately, using higher current density.

Jan 1, 1980

By F. W. Cox

Exhaust emissions were measured from 25 aircraft turbine engines using Jet A fuel. Analytical apparatus, procedures, and results are described. Carbon monoxide, carbon dioxide, nitric oxide, nitrogen dioxide, and aldehydes were measured at engine operating modes representing power levels used in airline operation. Carbon monoxide, hydrocarbon, and aldehyde emissions were highest at idle and lowest at takeoff; oxides of nitrogen were lowest at idle and highest at takeoff. Of the total oxides of nitrogen emitted, nitrogen dioxide constituted from 10 to 100 pct, depending on the exhaust gas temperature. Engines retrofitted with smoke-reducing burner cans produced less carbon monoxide, hydrocarbon, and aldehyde emissions, and slightly more oxides of nitrogen then engines with standard burner cans.

Jan 1, 1972

By Kenneth C. Ko

An engineering investigation was carried out on the technical and economic feasibility of implementing flexible liner/backpacking support systems In an advancing tailgate longwall mine. The system for a model mine consists of a circular tube constructed of liner plates and flyash backpacking. Flyash is pneumatically stowed into the tailgate. Small amounts of cement may be mixed to improve the support capability of the fill In difficult local ground conditions. Water is added inside the nozzle immediately prior to spraying. Results of theoretical analyses and a field test show that the designed system is technically feasible, can be cost-competitive, provides more stable ground conditions, and can Increase productivity and coal recovery, when compared with existing retreat longwall systems. In certain mine layouts, the new system can reduce the direct mining costs by a significant amount. The system would be particularly applicable to deeper coal beds with bad ground conditions.

Jan 1, 1980

By Arnold O. Tanner

The domestic mining industry continued to be strengthened and revitalized in 1989. The healthy conditions and the industry comeback that began in 1987 continued to spread and became more established for many commodities. Relatively comfortable and stable commodity prices, still found predominantly in the metals sector, reinforced other operational factors in bringing vitality to the mining and mineral processing industries. New streamlined business practices, mine and plant modernizations, and the progressive use of new technologies successfully helped lower operating costs and increase efficiency during the past 5 to 7 years. An element common to these three factors of industry renewal and growth was the ever-increasing infusion of and growing dependence on constantly advancing computer technology applications. This trend of increasing computerization was occurring throughout the mining and mineral processing business while it similarly was in most facets of modern business and culture. Some commodities and companies still struggled to outlive sluggish prices and other unstable market conditions or to modernize their businesses, but increases in productivity and profits were more common. A trend toward increased mechanical excavation in nonsoil materials was beginning to surface as a substitute for standard cyclic mine development techniques, such as drill-and-blast and surface shovel-and-truck routines. More continuous mechanical excavation offered the potential for increased production, fewer people at the working face, better ground control, and generally improved safety. The main limitation was rock hardness. The construction industry had already recognized the benefits of tunnel-boring machines for long underground drives and mechanical planers for pavement removal. The Colorado School of Mines held a short course during the year entitled, "Mechanical Excavation Techniques in Mine Development and Production,'" which was at-tended by nearly 100 engineers from 12 countries. The consensus of attendees was that for the most efficient use of these machines and techniques, new mining plans needed to be developed beyond the simple adaptation of those excavators to existing mine plans.1

Jan 1, 1991

By R. V. Petrella

The flash induced combustion of Sewell and Pittsburgh coals was studied in air and in oxygen. The primary decomposition and combustion processes occur within the first 300 ~sec in oxygen and slightly later in air. Strong absorption spectra of CN and OH are indicative of the decomposition and combustion processes, respectively. Kinetic spectroscopy and combustion product analyses indicate that only about 35% of the coal dust is consumed in the explosive combustion which takes place in several (1-5) distinct but similar steps. The combustion-modifying effects of (NH4)2HP04, NH4H2P04, KHC03 and Rock Dust were studied in the 1-20 wt % range in coal dust flash com-busted in air and oxygen. The study reported herein shows Rock Dust to be the most efficient coal combustion inhibitor. KHC03 is the least effective agent, with the phosphate salts showing marginal effectiveness.

Jan 1, 1976

Late in 1974 at a meeting with the Cedar Coal Company in Chelyan, West Virginia, a very definite requirement for an automatic heat sensing fire suppression system for the type coal augers used in their mine was revealed. Several fires had been experienced, and while equipment loss was a consideration, operator safety was also a concern. As of that date no one had developed an automatic system specifically for fire suppression on coal augers. II. EQUIPMENT DEVELOPMENT As a result of the above meeting, an unsolicited proposal was made to the Bureau on March 1, 1975, and a contract was issued to provide the following services: A. Determine and define fire hazard problem on Compton Coal Auger. B. Modify or otherwise mike a Lease "AFEX" system suitable for protecting the fire hazard area developed in paragraph "A". C. Make installation of "AFEX" system. D. Monitor installation for reliability for a period of 90 days after installation. C. ConJurt a simulated fire test to determine effectiveness on system.

Jan 1, 1975

By M. C. Irani

The Bureau of Mines, in cooperation with the Mine Safety Appliances Co., has developed a continuous-recording methanometer utilizing a catalytic combustion detector. The methanometer, which is presently operating at 22 exhaust fans at 14 mines in the Eastern coalfields, is reliable and simple to install, operate, and maintain. The instrument and the details of its installation and calibration are described. Analytical data obtained by infrared spectrophotometer and gas chromatograph are presented to substantiate its re liability.

Jan 1, 1974

This report summarizes a study conducted by The Service Bureau Corporation for the Bureau of Mines. Evaluations reflected herein are the result of an independent investigation by The Service Bureau Corporation of methane considerations during coal mining. The study is oriented toward a systematic analysis of methane control problems during coal mining. Throughout this study an attempt has been made to ensure considerations consistent with the recently enacted Federal Coal Mine Health and Safety Act of 1969. References to reports by The Bureau of Mines and others are made for the purposes of establishing identification between the evaluations contained in this report and on-going research efforts.

Jan 1, 1970

By Oliver Bowles

Marble is one of tile most beautiful and enduring materials employed in the construction industries. Because of its diverse colors, decorative patterns, and varying textures, it has furnished material for artistic architectural design for many centuries. The marble industry is described in some detail in Bureau of Mines Bulletin 106, The Technology of Marble Quarrying, which, unfortunately, is now out of print but may be consul ted at most large libraries. Onyx marble and travertine are discussed in Bureau of Mines Information Circular 6751. The purpose of this paper is to describe the main features of a distinctive group of ornamental marbles known as the serpentine marbles or verde antiques.

Jan 1, 1938