Search Documents

By R. W. Stahl

An award is a form of recognition given for superior performance in a special field of endeavor. Each year awards are given by the Joseph A. Holmes Safety Association and the National Safety Council to mineral industries' mines, quarries, and plants that have worked a specific number of man-hours without a lost-time injury. These awards have a dual significance in that they prove that efficiency can be attained without injury to persons. Safety awards do not result from luck or good fortune but do result from sincere desire coupled with sufficient effort and cooperation to achieve a desired goal.

Jan 1, 1963

By F. M. Goodwin, John Campbell, G. W. Jones

"INTRODUCTION In cooperation with the Boston Edison Co. and the Boston Consolidated Gas Co. of Boston, Mass., a survey has been conducted continuously since 1929 by the Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes of the Boston Edison Co. The New England Telephone & Telegraph Co. also has cooperated in the investigation, and tests have been made in its manholes from May 1, 1933, to October 15, 1937. Yearly reports. 6/ on the results obtained since the beginning of the survey have been published.The methods and procedure of conducting the survey in 1937 were the same as heretofore."

Jan 1, 1939

By Edward A. McClatchie

A methane monitor that complies with 30CFR75.313 has been designed and fabricated using a novel pressure modulated infrared absorption technique. The methane monitor met or exceeded in performance all of its target specifications. The monitor was operated continuously during production mining for the entire duration (45 days) of the in-mine test; no failures occurred during the test. The monitor was regularly checked with calibration gas and no shifts in calibration were found during the in-mine test. Operating principles, performance data and electrical schematics are included in the report.

Jan 1, 1976

By Lloyd Williams, James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limes tone- dolomi te beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Nov 1, 1964

By A. U. Miller

Definite progress has been made in accident prevention in Illinois during the past few years; the State Department of Mines and Minerals is receiving excellent cooperation from coal companies and employees, the companies are making greater effort to maintain their mines in good condi- tion, and the employees are eliminating more unsafe practices. As a result, some coal companies have made commendable safety records that prove that coal can be mined with a comparatively low accident rate. However, there is need for further improvement, as the accident rate of the State as a whole is much higher than it should be. During the 55-year period 1882-1936, in- clusive, reports of the State Department of Mines and Minerals show a total of 7,005 (an average of 127.36 per year) men killed in and around the coal mines. Of this number, 6,425 (91.7 percent) were killed underground, 346 (4.9 percent) in the shaft, and 234 (3.3 percent) on the surface. Of the fatalities underground, 3,300 (51.3 percent) were killed by falls of roof, sides, or face coal, 1,167 (18.1 percent) by haulage, 639 (9.9 percent) by handling explosives, 579 (9 percent) by explosions, 151 (2.3 percent) by electricity, and 589 (9.1 percent) by other means. Of the fatalities in the shaft, 171 men (46.5 percent) were killed by falling down the shaft, 14 (41.6 percent) by the cage, and 31 (8.9 percent) otherwise. On the surface, 113 (48.2 percent) of the fatalities were due to railroad cars, 51 (21.7 percent) to machinery, and 70 (29.9 percent) to other causes. The fact that 7,005 lives (an average of 127.36 per year) were lost during 1882-1936 is sufficient evidence that in the past too little interest has been taken in safety by either the management or workers. A realization of this deplorable loss of life should act as an incentive to the industry to make greater effort to prevent accidents in the future. After an accident occurs, the facts pertaining to it become history, and anything that may be done afterward cannot change in any way the damage that has already been done, such as loss of life, personal injury, and destruction of property. The main benefit that can be derived from an acci- dent is that suitable procedure may be adopted and some lesson may be learned to aid in preventing a similar accident in the future. All accidents, par- ticularly serious ones, therefore should be investigated and an effort made

Apr 1, 1938

By George A. Morrison

This paper describing the methods of mining and crushing limestone at the West Winfield, Pa., limestone mine of the West Penn Cement Co., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and coats in the various nonmetallic mining districts. HISTORY The limestone deposits of western Pennsylvania have been exploited for many years and have been quarried extensively at West Winfield in Winfield. Township, which lies in the southeastern corner of Butler County.

Jan 1, 1931

By J. W. Thompson

RAILROAD GRANT-MDIERALS. Diatomaceous or infusorial earth when found in such quantity and quality as to render lands containing deposits valuable therefor are mineral lands within the meaning of the mining laws and must be excepted from grants to the Central Pacific Railway Company. Central Pacific Ry. Co., In re, 45 Land Decisions, 223, p. 226. RAILROAD GRANT-CLASSIFICATION, If any evidence of minerals is found upon lands within a railroad grant and the showing is sufficient in the opinion of prudent and qualified persons to warrant further exploration and expenditure, with reasonable prospects of success, then the land can not be classified as nonmineral and is not subject to the grant to a railroad company. But where there is no present indication of minerals nor any geological evidence upon which to base a mineral finding, land should not be classified as mineral, or held for further classification and reserved from the railroad's grant, upon the surmise that future prospects might disclose evidences of minerals. Southern PacUl.c Ry. Co., In re, 45 Land Decisions, 326, p. 329. INDEMNITY SELECTION BY RAILWAY COMPANY, Under section 3 of the act of July 2, 1864 (13 Stat., 365), and the joint resolution of May 31, 1870 (16 Stat., 378), the Northern Pacific Railway Company could take coal and iron land within its primary or grant limits. It could not base an indemnity selection upon the claim that certain land was coal or iron in ;;haracter, as such land was not lost to it as part of the grant. But the company was authorized to select other lands in lieu of those lost because of their mineral character, but the word "mineral" did not include iron or coal, and, accordingly, the railroad company was entitled to take coal lands under its indemnity selection.

Jan 1, 1917

By Jack Mantel

The goal of this 42-month contract was to increase safety in low-seam underground coal mines through development and in-mine evaluation of a temporary roof support system for roof drills and floor-riding operator compartments for a loader and shuttle car. The program was performed in three phases. During Phase I, state-of-the-art canopy technology was investigated, and preliminary design and mock-up evaluations were performed for temporary roof supports for single-and dual-boom bolters and for transverse-mounted floor-riding canopies for a shuttle car and coal loading machine. The shuttle car and loader canopies were approved for further development, and the design, fabrication, testing, and certification were completed in Phase II. In Phase III, the Bureau of Mines furnished an FMC 6L shuttle car fur use in the evaluation of the canopy for 45 shifts. The shuttle car canopy was evaluated at Virginia Crews Coal Company in West Virginia. Efforts to secure an evaluation site for the loader canopy were unsuccessful. The loader canopy was shipped to Bruceton for possible future evaluation.

Jan 1, 1985

By Tracy. L. D.

"Since the introduction of pulverized coal as a substitute fuel for natural gas in the various types of heating furnaces used, in steel mills, a number of fires and explosions have occurred, resulting in the loss of life and property.As one of the primary functions of the Bureau of Mines is to conduct investigations in the utilization of mineral substances with a view to increasing safety in the use thereof, it was deemed advisable to investigate the hazards involved in the industrial use of pulverized coal and, if possible, to devise methods of preventing future accidents arising therefrom. The knowledge of the explosive qualities of coal dust which the Bureau has gained in studies affecting dust explosions in coal mines was of material assistance in these investigations.Several plants were visited in which either fires or explosions had occurred, and data obtained as to the probable cause of the accidents.There was found to exist, among some of those employed about the furnaces, a lack of knowledge of the explosive and inflammable qualities of powdered coal.A small stream of pulverized coal leaking down from a defective joint in a coal transport line did not attract much attention, whereas, had a leak in a natural gas line occurred -wider similar circumstances, no doubt it would have had immediate attention.As a matter of fact, if by any means the duet cloud should come in contact with an open flame or hot metal, the effects would be as disastrous as if it had been gas.This is exceedingly well illustrated by an accident which came to the writer's attention. In the system used at this particular plant, the pulverized coal is transported to the furnace through compressed-air lines. The fuel is fed from a storage bin to a blowing tank in quantities as desired, after which compressed air is admitted and the powdered coal blown to the furnaces. At the time of the accident some repairs were being made to the tank, and it was supposed that the air pressure had been entirely released as the pressure gage stood at zero. There was, however, one or two pounds air pressure remaining and when one of the connections was taken off, a cloud of dust was blown across the room, 30 or 40 feet towards the drier furnace where it came in contact with some live coals. Immediately the entire room was filled with flame which rolled back and forth over a specs 50 feet or so in length."

Apr 1, 1921

"SUMMARYThe K.M.A. reservoir was discovered to be oil bearing at a depth of 3,719 feet on March 11, 1931. Extensive development, however, was not begun immediately, because the discovery well had a low initial daily oil production, and market conditions for oil were unfavorable. Development of the field progressed slowly for the next 6 1/2 years. In the latter part of 1937, a wildcat well approximately 2 miles southwest of the discovery well was drilled on a magnetometer high and completed with an initial flowing production of 2,016 barrels of 43° A.P.I.-gravity oil in 12 hours. Rapid development of the southwestern part of the K.M.A. field was begun immediately and continued until over 700 wells were drilled and approximately 12,500 acres proved oil productive.Because of the large size of the entire K.M.A. field, this report is limited in scope to the southwestern part only, and the discussion that follows pertains to this area only. The closing date for production statistics is August 1, 1949.The K.M.A. structure is a complex anticline having a maximum closure of 250 feet, and the K.M.A. formation is composed of sediments that grade from limestone through sandy lime and limy sand to sandstone with thin streaks of shale. Two distinct members of the K.M.A. formation, zone I and zone II, are oil productive. Core analyses indicate the average porosity to be 16.5 percent for zone I and 16.1 percent for zone II. A relationship was established from core data, which showed the correlative permeabilities to be 42.1 millidarcys for zone I and 39.5 millidarcys for zone II, whereas the arithmetical averages of the permeabilities were 84 millidarcys for zone I and 216 millidarcys for zone II. Connate water saturations were 17.5 percent for zone I and 20.0 percent for zone II. The porosity-saturation method, using a thickness-correction factor, was employed to calculate the volume c 168.1 million barrels of stock-tank oil initially in place in the reservoir. Analyses of the reservoir oilIn that, although the initial reservoir pressure was 1,750 p.s.i., the original reservoir oil was saturated to only 1,300 at which pressure 1 barrel of stock,tank oil contained 525 cubic feet of gas in solution.A serious decline in reservoir pressure during the 2 years of rapid development alarmed the operators and caused them to consider a cooperative pressure-maintenance program. In the latter part of 1939, the K.M.A. Pressure Maintenance Association was organized, and the gasoline plants in the field agreed to process the wet gas and return the dry gas to leases having gas-injection wells. Approximately 27 percent of the cumulative volume of produced gas had been returned to the reservoir by August 1, 1949."

Jun 1, 1952

By R. E. Heithecker

The Zwolle oil field of Sabine Parish, La., is different from most oil producing areas of the State in that the oil is obtained from marl and chalkrock formations. The thickness of the reservoir rocks averages 500 feet; but production is not continuous throughout this thickness, as the oil apparently is localized in vertical and nearly vertical solution cavities and channelways or in porous zones of limited horizontal extent. The nature of the oil accumulation has caused two outstanding peculiarities of the field: (1) About 60 percent of the tests drilled were dry holes and (2) there were many instances of well interference. Commercial production was discovered in November 1928, after 17 years of prospecting in and around the present limits of the area now developed which has a length of about 22 miles and a maximum width of 4 miles. The field had produced 10,266,896 barrels of oil to January 1, 1934. The oil ranges in gravity from 400 to 420 A.P.I.

Jan 1, 1934

By Ann C. Kim

This Bureau of Mines report summarizes the methods and results of many of the laboratory studies on spontaneous heating of coal published in the last 50 years. It includes a brief description of experimental methods, indices of combustibility, and important contributing factors. Adiabatic calorimetry, isothermal calorimetry, [0], sorption systems, or temperature differential are the most frequently used experimental methods. Indices of combustibility include various heating rates, crossing point temperature, ignition temperature, and CO index. Factors that affect the spontaneous heating of coal include air flow rate, changes in moisture content, particle size, rank, temperature, pyrite content, geological factors, and mining practice. Experimental conditions and results from 20 papers are summarized in an appendix, and the bibliography contains 45 references.

Jan 1, 1977

By J. S. Hansen

To advance technology that can conserve critical materials, the Bureau of Mines investigated a cast-on hard-surfacing that wear resistance and confines alloy additions to wear-prone surfaces. Wear-resistant material in form is on a polystyrene , the is embedded in a mold of unbonded s and the wear-resistant material is transferred to a cas surface at the time of For low-stress abrasion, derived from high-carbon ferro-chrome had higher wear resistance than did commercially available weld-hard. The microstructure of the was typi-white iron carbides. Free carbon added to the ferrochrome powder produced more M7C3 carbides than did material contained in surfacings made from ferrochrome alone, and improved the wear resistance. Several white iron powders with greatly reduced chromium contents also white iron contain-M7C3 carbides. One derived from white iron powder had wear resistance to that of weld-deposited hard facings. Among the parameters investigated, surfacing thickness was found to have a or influence on diffusion of elements out of the , microstructure, and wear resistance. The results of field tests on bucket-wheel excavator teeth and plowshares with cast-on hard surfacing are given.

Jan 1, 1985

By Zabetakis M. G.

This Bureau of Mines report presents a brief summary of the explosion trends in United States coal mines for the past 160 years. These trends show that in spite of the overall improvements in mine safety, the number of fatalities from ignitions of methane has actually increased in recent years. Suggestions are made of procedures that can be utilized to reverse this trend.

Jan 1, 1973

By J. M. Riley

The Bureau of Mines investigated a promising new technology for recovering A1203 from alunite to support the Bureau's alumina miniplant project. Results are presented for a study of the technical feasibility of treating alunite crushing and grinding reject fines for recovery of A1203. Alunite pellets having sufficient strength and resistance to degradation were produced by combining fines and coarse alunite with a KOH binder. The best pellets were prepared, in a laboratory pelletizer, by adding 1 pct KOH as a 5-pct solution to a mixture of 40 pct alunite dust (98 pct minus 65 mesh) and 60 pct coarse alunite (minus 20 plus 65 mesh). Calcines suitable for K2SO4 and A1203 recovery were produced by reducing dehydrated alunite pellets with sulfur in a laboratory shaft furnace for 4 h at 600° C, followed by air oxidation of the reduced calcine for 1 h at 600° C. This report presents design calculations, schematic diagrams, and discussions of the essential features of a proposed process research unit (PRU)--a continuous, 6-lb/h alunite shaft furnace--for studying the process.

Jan 1, 1983

By William O. Vanderburg

This paper gives the results of a reconnaissance of the mining districts of Mineral County, Nev., made during the month of June and the first 10 days in October 1936.3/ During the field work virtually all the mining districts in the county were visited and many data were obtained relative to active and inactive properties. The report covers the location of the various mining districts, nature of deposits, ownership, information on past and current activity, data on economic conditions, and general information likely to be useful to operators and investors and others interested in mining. The geology of the deposits is discussed only in a general way. For nearly three-quarters of a century mining tin Mineral County has been the principal if not the only industry of importance. At times it has reached a very low ebb, and at other times it has been attended by the wild excitement that usually accompanies valuable discoveries of precious metals.

Jan 1, 1937

By Keith L. Harris

The U.S. economy continued to grow moderately in the third quarter, but at a slightly higher rate than in the previous quarter. According to the Department of Commerce's preliminary estimate, real gross national product (GNP) grew at a seasonally adjusted annual rate of 3.3% during the third quarter of 1985, compared with a revised 1.9% for the second quarter and 1.6% for the third quarter of 1984 (table 1). Civilian unemployment dropped from the constant 7.3% rate between February and July to 7.0% in August and 7.1% in September. Employment on nonagricultural payrolls continued to increase (table 2), resulting in a continued rise in personal income, which in turn supported growing consumer purchases. Although purchases of services continued to provide the underlying foundation for the economic growth, the manufacturing sector received additional stimulus from significant increases in consumer purchases of durable goods, particularly automobiles. The increased demand for durable goods resulted in significantly higher industrial production for August and September, compared with levels attained previously this year (table 3). Capacity utilization increased to 80.5% in August but returned to 80.2% in September, matching the 1985 low previously reached in July (table 4). The real net export deficit grew only $0.2 billion in the third quarter; at $34.0 billion, however, it continued to exert a negative influence on the economy. On September 22, in an effort to reduce the deficit and make U.S. goods more competitive on world markets, the U.S. Government agreed to cooperate with the Governments of France, the Federal Republic of Germany, Japan, and the United Kingdom in attempting to lower the-value of the dollar in relation to other world currencies. Low inventories, rising factory orders and construction spending, the possibility of a lower U.S. dollar, and aggressive automobile production plans announced by domestic producers for the fourth quarter indicate the potential for an increase in manufacturing activity in the United States.

Jan 1, 1985

By Henry Kreisinger, WALTER T. RAY

This preliminary bulletin was written as the first of a series of several on the significance of drafts in steam-boiler practice, the succeeding bulletins to be along the same lines but of a more advanced character. The conclusions arrived at are tentative, and are the result of a study of one of the many problems growing out of a general plan of the United States Government to increase the efficiency with which the coals of the country are being used. Greater efficiency requires better boiler and furnace design. The experimental study of drafts on which the conclusions presented in this bulletin are based formed part of the fuel-testing investigations that were carried on by the technologic branch of the United States Geological Survey and have been transferred to the Bureau of Mines. The experiments made seem to indicate that it is possible to double or treble the capacity of a plant without making any radical changes the furnaces and boilers. These increases require about double and treble the quantities of air to be put through the fuel beds and boilers. It also seems probable that rebafHing the boilers will often permit the capacity to be doubled or trebled, while still getting more steam than formerly per pound of coal for uses outside the boiler room. These experiments were undertaken with the object of clarifying ideas concerning the passage of air through fuel beds and boilers. Measured weights of air were passed through two beds of lead shot, series, one of which remained always the same and represented a boiler; the other being varied as to size of shot and depth of bed, and representing a fuel bed. Careful observations were made of the weight of air passing through the beds per minute. All data were plotted in many charts, so as to permit the study of them from several points of view. A number of laws were deduced bearing on the relative amounts of power required to force air through fuel beds of various thicknesses, composed of various sizes of coal, and through boilers of various lengths and areas of gas passages. An important part of the discussion relates to an increase in the capacity of boilers by increasing the amount of power applied to pressure and exhausting fans and thus forcing several times as much air through the fuel beds and boilers. may be possible, as a result of these investigations, to raise the rate of working the boiler heating surface to three or even four times its present value. Such an increase would undoubtedly mean new designs of grates, stokers, furnaces, and boilers, especially fitted for high rates of working. Fan equipments designed to supply three or four times as much air under several times the pressure would be provided with more efficient engines, thus giving an additional factor favoring high-capacity working. It must be borne in mind, as stated above, that the results are tentative. It will cost money to force gases at high speeds through fuel beds and boilers, and there will soon be pressing need of such quantitative data as will enable the largest possible part of the energy imparted by the fans to be advantageously utilized. We desire, to thank our superiors, especially Messrs. L. P. Breckenridge and D. T. Randall, for their helpful criticism and suggestions.

Jan 1, 1911

By C. P. Bowie, George L. Gates

"INTRODUCTION Experience in drilling oil and gas wells has shown that the voidance of blow-outs, twist-offs, fishing jobs, loss of circulation, and heaving and caving of shale formations into the drill hole depends largely on how well the drilling-mud fluid serves its purpose. A possible method for the control of the drilling fluids may be seen from a study of the relation between the particle-size distribution and some of the important drilling-fluid properties, such as the ability to build quickly a relatively impervious mud sheath on the wall of the hole in the porous formations penetrated by the bit during drilling operations. In a wartime economy, which urgently requires conservation of steel, proper functioning of the drilling fluid is particularly important because, as Parks 4/ has stated, intelligent use of good drilling fluids makes possible drilling of wells for thousands of feet in open holes without the necessity of setting protective strings of casing to control the movement of salt water, gas, and troublesome formations into the borehole; consequently, especially in deep wells, of proper drilling fluids materially reduces the need for casing and lowers the cost of drilling and completing the wells."

May 1, 1942

By A. N. Fried

With the growing importance of fluid injection in recent years, the petroleum industry has been investigating and field- testing a variety of new methods designed to modify the physical properties of reservoir oil to improve the efficiency of gas and water injection. These procedures include condensing-gas drive, LPG (liquefied petroleum gas) injection, alcohol-slug process, high-pressure-gas displacement, detergent-solution flooding, and in situ combustion (30, 37).3 A new and different method to increase the effectiveness of gas and water injection has been tested by the Bureau of Mines, Consideration of both fundamental and practical factors that operate to limit the oil recovery attain- able by conventional oil-displacement mechanisms led to the concept of a displacement mechanism called the foam-drive method. This report describes the experimental study that tested this concept in the laboratory.

Jan 1, 1961