Search Documents

By Thomas J. Fisher, John J. Sammarco, Gary L. Mowrey, Edward F. Fries

This report (Safety File 3.0) is the fourth in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g] and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment.—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • 5.0 Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is the how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. [ ]

Jan 5, 2002

By Thomas J. Fisher, Christopher C. Jobes, Edward F. Fries

This report (Software Safety 2.2) is the third in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended or use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g] and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and non networked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety .• 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment.—The independent assessment of the Safety File is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • 5.0 Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be don and the guidance is the how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treaty of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. [ ]

Jan 9, 2001

By Mackenzie Burnett

The Brattice Window Method was used to measure the leakage rates of a total of 42 ventilation stoppings in 8 hardrock mines. Various types of stopping construction were evaluated. The following types are listed in order of decreasing effectiveness: 1) Cinder block, 2) Timber and mortar, 3) Timber and polyurethane foam, and 4) Timber and brattice material. There are slight differences in the effectiveness of the first three types, while the timber and brattice type is substantially inferior to the others. The repeatability of the Brattice Window Method was found to vary with physical conditions in the mine such as stopping location with respect to intersections, regularity of drift cross section, and the presence of hardware such as air and water pipes, timber sets and wire mesh. The Brattice Window Method is viewed primarily as a tool for estimating and comparing stopping leakages for the purpose of determining where repair efforts should be concentrated. A laboratory test program resulted in the derivation of several "rules of thumb" for employing the Brattice Window Method, which will aid in securing accurate and repeatable data.

Jan 1, 1979

By Jack Smith

New turbine blades designed to resist ash erosion were tested by the Bureau of Mines in a pilot-scale coal-fired gas turbine. After a total of 1,963 hours, the rotor blades were only slightly eroded; and they had an estimated useful life of 20,000 to 30,000 hours. Changes in aerodynamic design of the blades successfully concentrated the ash at the outer casing, but stepped sidewalls for the rotor drum and wear strips at the bases of the rotor blades are still needed to minimize wear at these points. Stepped sidewalls and wear strips did not adequately protect the stator blades. Ash slightly eroded their leading edges, above the inserts, and cut notches into their trailing edges near the bases. Stator blade life was estimated at 5,000 to 7,500 hours. Blade erosion in these tests was less severe than with previous designs, but more efficient combustors and ash separators are required to reduce the amount and size of ash entering the turbine, to achieve acceptable blade life for commercial operation.

Jan 1, 1967

By Charles B. Carpenter

The New Hope field was selected for study by; Bureau of lanes engineers because many problems met by, the operators during development and operation were unique to petroleum-engineering experience. Solving these problems is believed to have doubled the ultimate recovery of oil from the field. Since the discovery well was 'completed, in April 1943, an oil-productive area of 4,950 acres- has been delineated by the drilling of 64 wells, four of which were dry holes. Four oil-bearing reservoirs - the Bacon oolitic limestone, and the Hill, Pittsburg) and Elledge sandstones, all, in the Trinity group of the Lower Cretaceous series-- have been penetrated at depths ranging from 7,300 to 8,100 feet. Three of these reservoirs were found to be closed-type or solution gas-drive reservoirs, and one - the Hill - was an open-type or water-drive reservoir. During the course of the study, the Tide Water Associated, Oil Co. and -Seaboard al Co. of Delaware made available to the writers all well records, electric logs; and coring, production,, and pressure data. The ,writers performed Certain field and laboratory- tests on cores of ,the reservoir racks and' samples -of the reservoir Oils. Analyses of cores from the four reservoirs showed average .porosities ranging from 10 to 18 percent, average permeabilities of 17 to 297 millidarcys, and -average 'connate water contents ranging from 25.4 to 30.6 percent. Subsurface and recombined samples of reservoir oils indicated that the oils in the Bacon Hill, and Pittsburg reservoirs contained ,206 to 422 cubic feet of gas in solution per barrel initially, and that the, reservoir oils were undersaturated with gas. No samples' of oil from the Elledge reservoir were analyzed, and because of meager data this reservoir was not studied in detail. 4 The presence of free 'gas' or a' gas cap, however, indicated that the oil in the Elledge reservoir was saturated with gas. The rapid decline in pressures in- the' four reservoirs during the 'first year of operation alarmed the operators and provoked them to investigate the reservoir conditions to determine the cause.

Jan 1, 1949

By J. R. Thoenen

In June 1929 the Bureau of Mines issued a 13-page information circular entitled "Mineral Wool," which was one of the first publications to present to the public Rome technical aspects of the mineral-wool industry. Since then several articles on the subject have appeared in the technical press as well as in publications of State organizations. Inquiries for information on mineral wool have continued to be received by the Bureau of Mines in large number, and in 1935 it was decided to make a field survey of the plants then producing and to collect therefrom technical data to be compiled in a paper for nubile distribution. With the cooperation of the industry, this survey was made, and Information Circular 6984, Mineral Wool, was published in January 1930. The issue was exhausted after a few months, and requests for copies continued to come to the Bureau. As opportunity arose, further field studies were made in American as well as Canadian plants. The present circular contains the essential information in Information Circular 6994 together with date from later field studies.

Jan 1, 1939

By James L. Elder

The Bureau of Mines and the Alabama. Power Co. jointly conducted a first experiment in underground gasification of coal at Gorgas, Ala., during the fall and winter of 1946-47. This preliminary experiment showed that it was not difficult to maintain combustion of coal underground, and that coal in place could be completely gasified. It was noted that the high temperature developed by the gasification of coal in place brought about changes in overlying strata that appeared to be favorable to the process. The high temperatures caused the roof rock to become plastic, to expand, and to settle down on the mine floor directly behind the reacting coke face. These results were promising enough to warrant further investigation of the process. It was believed that if this action could be controlled properly with roofs of similar composition, it would tend to force the gas-making fluids underground against the coal faces. Plans for the second experiment were based in part on this favor-able roof action, and the successful operation of the planned initial straightline passages depended on this fact. Gorgas was chosen as the site for the second experiment for the following reasons: A tract of coal land of sufficient size was available and isolated from the main body of coal; the roof rock was similar in composition to that encountered in the first experiment; and the overlying strata were thick enough to eliminate some of the operating difficulties that had been encountered, In addition, power, water, and machine-shop facilities as well as an adequate supply of labor were available in this area, and the friendly cooperation of the Alabama Power Co. further recommended this site for the planned experiment.

Jan 1, 1951

By Robert S. Dalzell

Following the introduction of roof shields to the U.S. longwall mining scene in 1975, the number of shield faces (faces supported by shields) has increased steadily, and the occurrence of accidents associated with ground control inadequacies at longwall operations has shown a downward trend. However, ground control problems in longwall mining still exist. New mining systems, however efficient, have run afoul of roof control. Shield faces have suffered extended stoppages because of roof cavities. In this report, the Bureau of Mines addresses the problem of longwall roof control. The report presents a review of foreign remedial and strata replacement techniques for longwall faces and evaluates their potential for domestic application. The technology reviewed includes meshing, chemical rock stabilization, cribbing, strain-absorbent modules, inflatables, synthetic foam, and monolithic fills.

Jan 1, 1985

By B. C. Burgess

This paper, describing the milling practices at the Minpro plant of the Tennessee Mineral Products Corporation, Spruce Pine, N. C., is the first of a series being prepared by the U.S. Bureau of Mines on feldspar milling methods and costs in the various feldspar producing areas in the United States. It describes not only the latest practices in feldspar grinding but includes studies of the cost of producing ground feldspar. These cost studies, obviously of interest to every consumer and purchaser of feldspar and to all feldspar grinders, are also of value to the small operator, who is generally prone to understimate his real costs. It describes the latest practices in feldspar milling and includes detailed costs of grinding. The cost tabulations presented show operating expenditures only and not total production costs. Details of costs are given only to the extent that they are essential to the technical discussion and study of the methods employed. A description of the recently installed milling unit for the preparation of granular glasspar by graded crushing, and magnetic separation is of particular interest. It illustrates how highly specialized feldspar milling has become, and to what an extent grinders are going to supply consumers with the products best suited for their particular needs.

Jan 1, 1931

By Ronald Althouse

During the past five years under contract with the U. S. Bureau of Mines (BOM Contract J0308002). West Virginia University's Mining Extension Service (WVU-MES) has designed, developed) and delivered to the mining industry a comprehensive training program for Mine Rescue (MR) teams and a management planning tool for Mine Emergency Preparedness. The Mine Rescue team program is systematically built on a set of training objectives, backed up by content, allowing mine operators to conduct team training activities. These materials are user-ready, provide the MR principles and practices for both initial and advanced training, and supply teams with exercises geared to problem-solving activities. In addition to an instructor's program guide, the eight (8) modules that comprise the initial (20 hour) MR training are: an Introduction to Mine Rescue, an Introduction to Self-Contained Breathing Apparatus (SCBA), a set of modules covering each approved minimum 2-hour SCBA (i.e.) the Draeger BO 174-A. the McCaa) the Aerolox. & the Scott Rescue-Pak), and a manual on Auxiliary Apparatus as well as the Chemox Auxiliary SCBA. Advanced, annual refresher training (40 hour) is covered by seven (7) modules that spell-out the principles and practices needed to establish surface organization, to handle mine gases as well as mine ventilation, to conduct exploration, for fires, firefighting, and explosions, to rescue survivors and recover bodies, and to accomplish a mine recovery. Approved by MSHA in 1984 to meet requirements for 30 CFO. Part 49, these materials provide a basis for trainers' instruction, for comparison of team capabilities, for modifying programs resources, and services, and for program planning. The Mine Emergency Preparedness Program (MEPP) is used by management as a tool in the preparation of company personnel for handling a mine emergency operation. As a wholly new program. MEPP depends upon development of a Mine Emergency Organization and Emergency Operations Procedures. It also requires regular scheduling of drills) periodic mock emergencies, and evaluation of organizational responses and program performance beyond required training of mine rescue teams. MEPP materials are arranged into three sets of guides: 1) the Preparedness Program System Guides include an Executive Summary, a Program Director's Guide Mine Emergency Organization, and Emergency Operations Procedures; 2) the Emergency Organization (MEO) User's Guides cover the Rescue and Advisory Division, the Technical/Safeguarding Division, and the Surface Support Division; and 3) the Emergency Procedures (EOPS) User's Guides detail Containment Level Procedures, Notification Level Procedures. Mobilization Level Procedures, and Deployment Level Procedures.

Jan 1, 1986

Research personnel from the Bureau of Mines, representatives of the Mining Enforcement and Safety Administration (MESA), and members of the mining industry met with other Government and Industry representatives at three seminars held in Pittsburgh, Pa., November 4, 1975; St. Louis, Mo., November 6, 1975; and Denver, Colo., November L1, 1975, to discuss the results of Bureau-sponsored research on coal mine illumination. The program, aimed at developing suitable illumination systems fur the working; places of underground coal mines, covered hardware development and field evaluation and the status of proposed MESA standards and proposed MESA enforcement procedures. These proceedings contain the opening remarks to the seminars and eight technical presentations an various aspects of coal mine illumination.

Jan 1, 1976

By N. A. Eilertsen

Procedures of mining high-calcium limestone underground at the Kimballton mine of the Standard Lime and Cement Co. in Giles County, west-central Virginia, are described. Drilling and blasting procedures arc discussed in detail, and direct mining costs are tabulated in percentage of total cost. Output, about 1,725 tons of limestone a day, is attained with heavy trackless equipment by the room and pillar method of ruining; modified by benching floors. Operating features include underground air compression, electric-eye control of curtained doorways, use of a single jumbo drill rig for all drilling, and an effective plan for maintenance of equipment. The company's safety program has contributed to an outstanding safe mining record. The mina is integrated with a plant on the property which converts the stone to metallurgical and chemical grade lime.

Jan 1, 1964

By Frank J. Wiebelt

Under a general program to extend the resources of mineral deposits, the Bureau of Mines examined the Quien Sabe antimony mine in October 1948. The preliminary evaluation demonstrated that a diamond-drill program was warranted co establish the tenor and persistence of the veins and permit an estimation of antimony reserves. The Bureau of Mines conducted a diamond-drilling program on the property from December 1949 to May 1950. Ten holes aggregating 2,483 feet were drilled. Nine of the holes encountered antimony-bearing vein material.

Jan 1, 1956

By Alfred Bellows

The objective of this contract is to design, build and demonstrate a support system to improve roof control in the entries of longwall mines. The objective of this phase has been the detailed design of such a system and the selection of a test site in which to perform the pilot demonstration. The result is a complete set of detail drawings or specifications which define the three major components of the system. The Gate Support is a variation of a face chock which has an extended canopy and additional hydraulic legs to protect the region of the face-entry intersection. The Entry Support is a steel beam and hydraulic prop set which is reusable and serves to support the first 100 or more feet of entry inby the longwall face. The Transporter is a bolter-like vehicle with a crane used for installing and retreating the beam sets. The test site selected is CF&I's Allen Mine in Colorado. They presently use simi¬lar steel beams and expect the FMA support system to be more effective as well as recoverable. It is recommended that the completed drawings be used to build a prototype system and test it first in a remote section of the mine and then in the active longwall tail entry.

Jan 1, 1978

By H. A. Watson

This circular, which is a revision and combination of two previous publications,3 4/ presents information on the different types of equipment that may be used to analyze mine atmospheres, with particular reference to the application and limitations of each type. Such information is frequently requested by mining companies, State mining departments, and other agencies concerned with safety in mining who wish advice regarding methods of analysis of mine atmospheres and the equipment necessary for establishing laboratories for that purpose. Since the Haldane-type apparatus is particularly applicable to the accurate determination of carbon dioxide, oxygen, and combustible gases such as methane in mine atmospheres, that apparatus and the method of operation are described in detail. The circular presents results of a critical study of the accuracy attainable with the Haldane-type apparatus in the determination of methane in concentrations of the order of 0.25 percent, by volume. Analytical procedures involved in the other methods discussed are presented in publications referenced in this circular. Information is given also on the various accessory equipment needed in a laboratory for the analysis of mine atmospheres, and suggestions on laboratory design are included. INTRODUCTION 'The analysis of mine atmospheres plays an important part in promoting safety and maintaining safe conditions in mining operations, particularly in coal mining, where the flammable gas methane presents a continuous hazard in Nome mines and may be encountered unexpectedly in others.5/ Methane has been encountered also, often unexpectedly and with disastrous results, in noncoal mines and in tunnels under

Jan 1, 1956

By C. F. Jackson

This paper has been prepared as a progress report in connection with the series of articles on mining methods and costs which are being published by the U. S. Bureau of Mines in the form of information circulars. Then enough circulars have been completed it is planned to publish a more complete and comprehensive paper in bulletin form dealing with the subject of underground transportation. Progress reports, followed by bulletins, will be prepared from time to time dealing with other subjects included in the general study of mining methods at individual mines, such as mine development, drilling, and blasting; stoping methods (each principal stoping method to be summarized in a separate paper); ventilation; wage, contract end bonus systems, etc.

Jan 1, 1930

To develop a conceptual design for an automated longwall mining system, one should know what has been done, what is being done today and what is being planned for tomorrow. The bibliography referenced and discussed in this report provides a good source for that knowledge. To scientifically determine where attention should be focused to up-grade a system, the system must be quantized as far as possible. The Mechanization Profile of Appendix A-I is discussed in this report and has been used to analyze and determine the degree of mechanization currently in use and/or described in the literature for all three major elements of the long-wall system, namely, Winning, Roof Support and Haulage. The charted profiles make it self-evident where attention and design effort is needed to remove human operators from the face of the mine.

Jan 1, 1975

By GJ Hundman

The Multiple Unit Continuous Haulage (MUCH) System was designed to provide the capacity to continuously convey coal from the mining machine to the main haulage belt. The MUCH System has an operator who steers the lead vehicle, ever following the mining machine. All the remaining vehicles follow the path of the lead vehicle, with their conveyors automatically lining up between the lead vehicle and mine section panel belt. This is accomplished by mechanical linkages on the vehicles which are interconnected by steering bars between vehicles (patent pending). The MUCH System has an operator who steers the discharge vehicle when outby travel is required. Outby travel is just like inby, with each vehicle following the path of the preceding vehicle. Surface tests overwhelmingly indicate the "UCH System should track/retrack successfully in square pillar underground room and pillar coal mines with 18 ft. wide entries and slopes up to 10 percent. For 60 degree pillar plans the minimum entry width required is 15 ft. Surface tests also indicate the MUCH System will convey over 8 TPM of coal around 90 degree corners without excessive spillage.

Jan 1, 1983

By A. J. Kauffman

This study compiles data on the zircon resources of the Pacific Northwest States, Alaska, and California, to determine the productive capability of industrial concerns to make ductile zirconium and hafnium, and to investigate markets for the nonmetallic products of zircon. West coast zircon resources are large but mostly marginal to submarginal. Development of a stable and profitable zircon mining industry on the west coast will depend upon recovery and utilization of the other associated heavy minerals needed by regional and national markets. The west coast has the only completely integrated facility for processing zircon sand to reactor-grade zirconium and hafnium and for making fabricated products from these metals. The future of the zirconium metal industry appears to be good because of increased use of the metal for nuclear propulsion and power-generating plants.

Jan 1, 1965

By A. J. Kauffman

This study compiles data on the zircon resources of the Pacific Northwest States, Alaska, and California, to determine the productive capability of industrial concerns to make ductile zirconium and hafnium, and to investigate markets for the nonmetallic products of zircon. West coast zircon resources are large but mostly marginal to submarginal. Development of a stable and profitable zircon mining industry on the west coast will depend upon recovery and utilization of the other associated heavy minerals needed by regional and national markets. The west coast has the only completely integrated facility for processing zircon sand to reactor-grade zirconium and hafnium and for making fabricated products from these metals. The future of the zirconium metal industry appears to be good because of increased use of the metal for nuclear propulsion and power-generating plants.

Jan 1, 1965