Search Documents

By S. H. Ash

THIS REPORT covers the third in a series of five projects into which the Conowingo tunnel system has been divided for geographical and practical reasons. It outlines the work constituting Project No.3 that consists principally of the following: (a) To sink the No. 15 shaft and extend the Alden, Sugar Notch, Baltimore No.2, and Laflin shafts from their present depths to tunnel level; (b) to drive a tunnel off these shafts to connect with the western end of the tunnel in Project No.1 (Lackawanna) and to a point 1 mile south of the No. 15 shaft; (c) to construct an emergency pumping plant at the No. 15 shaft, complete with 3 centrifugal pumps of 200-cubic-foot-per-second (c. f. s.) capacity each, and a discharge-water shaft and a discharge tunnel for conducting the water from the pumping plant into the Susquehanna River; and (d) to construct a lateral tunnel 1 mile long off the main tunnel in the vicinity of the No. 15 shaft, to be known as the Wyoming lateral. The project, as outlined, is a self-contained drainage unit that will permit unwatering inundated mines and safeguarding active mines in the Wyoming Basin of the Northern field and also will handle the water in the Lackawanna Basin, thus permitting the temporary pumping plant provided in Project No.1 to be discontinued. The pumps installed in the temporary pumping plant provided in Project No.1 can then be moved to the emergency pumping plants recommended in Projects Nos. 2 and 3, to be installed as the third or standby unit.

Jan 1, 1955

By Harry R. Johnson

Domestic expenditures by the U.S. petroleum industry have exhibited distinctive shifts in emphasis over the past 20 years. From the end of World War II to 1955, expenditures for all phases of the industry expanded. Although over one-half of all expenditures were for production, the relative emphasis was changed after 1956-58 from production toward processing and marketing. The period 1967-69 marked the beginning of a return to emphasis on exploration and production. These trends in expenditure patterns are logical and rational when related to domestic and international economic conditions and to the widespread application of improved production technology. As the immense job of developing the oil resources of Alaska and other regions begins, the petroleum industry will continue to turn to external sources for working capital. Long-term debt will probably be the principal method of external financing through 1970, but a definite shift toward new common and preferred stocks will be made. Higher product prices may be sought by the petroleum industry, but the economics of crude-oil production, changes in the tax structure, and possible changes in the oil imports control program make the price structure of crude oil and crude-oil products unpredictable at the present time.

Jan 1, 1970

By G. A. Smyres

A GaC12--B2 l-eachtng procedure and meEal-recovery method for treating an arsenical Cu-Co sulfide concentrate was developed by the Bureau of Mines as an alternative to smelting, which is no longer considered an environmentally acceptable method for treating arsenic-containing ores. The procedure involved leaching in a CaC12 solution with CaC03 for 96 h at 26 pct solids (concentrate and CaC03), 1150 C, and a pressure of 50 psig (345 kPa) with oxygen. More than 98 pct of the cobalt and 97 pct of the copper were extracted, and 99.98 pct of the arsenic and 99.9 pct of the iron remained in the leached residue. A filtration rate of 2.9 gal/(ft2.h) [118 L/(m2.h)] and a cake formation rate of 36 Ib/(ft2.h) [172 kg/(m2.h)] were obtained by filtering reacted pulp at 1000 C. More than 99 pct of the copper in the pregnant solution was extracted as CuCl2 by golvent extraction with a new copper extractant. Copper was stripped from the loaded organic with a sulfate-chloride solution, which was used as the anolyte for electrowinning of copper in a membrane cell. Copper plate produced was more than 99.99 pct pure and requi.red 0.81 (kW'h)/lb Cu [1.78 (kW·h)/kg Cu]. Cobalt sulfide was precipitated at pH 3 with Ca(HS)2.

Jan 1, 1986

By T. J. McDonald

The methods used and the results obtained in the application of high-expansion foam on a recent fire in an operating mine in western Pennsylvania were reviewed. This is the first instance where foam has been applied extensively to a fire under actual mining conditions although considerable research has been conducted and experimental fires have been controlled. The Bureau of Mines began investigating the foam-plug technique in 1957 in its experimental coal mine, following reports of successful trials in Eng-land, where the basic methods, using the normal ventilating current, were developed. Early in the research it was apparent that the normal ventilating current in mines in the United States would not provide adequate air pressure to drive a foam plug the distance that might be required. Subsequently, the Bureau of Mines developed a portable high-expansion foam generating unit consisting of a fan having relatively high pressure potential, net, sprays, and metering equipment. To date, foam generators have been constructed by the Bureau, by at least one operating coal company, and by one manufacturer of safety equipment. A number of units from the latter supplier have been adopted by coal-mining companies as an integral part in their firefighting installations.

Jan 1, 1961

By R. B. Ladoo

"Present Situation:At the beginning of 1920 a general feeling of optimism was noted in many talc-producing districts. The industry seems to have recovered from the temporary depression of the first half of 1919 and many mills are running at capacity production with their entire output for 1920 contracted for. The imports of talc for 1919 were only slightly larger than in 1918 by weight and probably no more by value. Thus foreign competition has not begun to be seriously felt. Several new companies in this country have been organized, some to operate new deposits and others to continue the work done by others.An interesting phase of the present situation is the possibility of increased use of talc in paint. There is a shortage of barium sulfate used as a paint filler. Since, for some uses, talc is considered second only to BaSo4 as a filler for paint, it is possible that part of the shortage could be relieved by an increased use of talc.A series of physical tests upon all pigment materials used in the manufacture of paints is being conducted for the Paint Manufacturers Association of the United States. It is important that all types of talc be represented in these tests. Producers of finely ground talc, 200 mesh and finer, are urged to submit samples of at least two pounds each of these grades that are available to paint makers with trade name and quality data, to the Institute of Industrial Research, 19th & B Streets, N. W., Washington, D. C., where the tests are being conducted."

Jan 1, 1920

By F. S. Crawford

The average visitor to a large electric-shovel operation may wonder how electric power can be treated as carelessly as apparently it is in open-pit mining, and how the mining company can string it carelessly along the ground in great, black, hoselike cables, whereas the power company, which has learned to respect his deadly agency, keeps power lines far out of reach. This is explained by the fact that this particular kind of application of power to moving machinery requires the use of trailing cable instead of the more permanent type of construction that permits a moving contact, such as a trolley. The cables are designed to insulate fully the enclosed power lines against damage and loss of current; and employees are taught to handle them carefully, although engineers are not satisfied that the trailing cable is foolproof and are seeking constantly to improve methods and equipment to insure greater safety. In some sections they rely mainly on the construction of the cable and perfection of equipment, while in others additional precautions are taken, such as handling the cable with rubber gloves, slings, tongs, or loops. In some sections no temporary repairs are made to cables, while in others such repairs are made and later are vulcanized in the shop. At some operations the cycle of shovel duties is arranged so that cables are very seldom exposed to flying rock fragments while at others this exposure appears to be unavoidable. Methods of fastening the cable to the shovel frame and transporting the loose cable vary. Inspection and care of the cable are important in insuring its safety and durability. A limited amount of information was obtained by field engineers of the United States Bureau of lines from operators in various parts of the United States, as methods of handling electric-shovel operations differ with the districts; practices followed and equipment used in these districts are described in this circular.

Jan 1, 1936

By D. D. Bolstad

This report describes the construction and use of a direct-reading azimuth protractor (DRAP) by the Bureau of Mines for measuring fracture orientations in mines, tunnels, or other excavations having a magnetic environment. The DRAP allows a rapid and simultaneous measurement of dip and azimuth of dip of a fracture plane. The instrument is rugged, lightweight, and easily constructible from standard hardware items. The DRAP can measure dip to within ±0.5° and azimuth of dip to within ±5° of corresponding values obtained with a Brunton compass.

Jan 1, 1974

By C. P. Haller, S. J. Aresco, R. F. Abernethy

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash- softening temperature of ash, the free-swelling index, and the hardgrove grind- ability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instruc- tions issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the con- tractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal. The Government purchased approximately 5-1/4 million tons of coal in fiscal year 1953. In connection with these purchases, the Bureau analyzed 11,435 samples. These are published for the use of Government officials and the public. A series of publications has been completed on coal analyses by States, or, where production is small in any one State, by groups of adjacent States. In addition to analytical data showing composition and quality of coals of the States, the publications con- tain brief descriptions of the geological structure of the coal basins, typical mining conditions in the various districts, the principal economic data of the industry, and the relationship of mine or channel samples to delivered and tipple samples. The present publication covers many States but deals only with the analytical data of the coals. Previous publications in this series are: Bulletin 516, Analyses of Tipple and Delivered Samples of Coal (Collected During the Fiscal Years 1948 to 1950 Inclusive); Report of Investigations 4934, Analyses of Tipple and Delivered Samples of Coal (Collected During the Fiscal Year 1951); Report of In- vestigations 4972, Analyses of Tipple and Delivered Samples of Coal (Collected During the Fiscal Year 1952). Following are the Bureau of Mines technical papers published by States, with their numbers: Alabama, 347; Alaska, 682; Arizona, California, Idaho, Nevada, and Oregon, 696; Arkansas, 416; Colorado, 574; Illinois, 641; Indiana, 417; Iowa, 269 and 706; Kansas, 455; Kentucky, 308 and 652; Maryland, 465; Michigan, North Dakota, South Dakota, and Texas, 700; Missouri, 366; Montana, 529; New Mexico, 569; Ohio 344 (and Bulletin 499); Oklahoma, 411; Pennsylvania Bituminous, 590 (Supplement 645); Pennsylvania Anthracite, 659; Tennessee, 356 and 671; Utah, 345; Virginia, 365 and 656; Washington, 491 (Supplement 618); West Virginia, 405 and 626; and Wyoming, 484.

Jan 1, 1955

By R. T. MacMillan

A number of chemical techniques have been applied to manganese ores from three areas of Aroostook County, Maine. Although large tonnages of these ores have been proved, they are low grade, and their exploitation has awaited a suitable beneficiation scheme. As conventional ore-dressing methods had failed to yield satisfactory results, attention was turned to chemical procedures. Leaching with dilute (7-percent) H2S04 extracted over 90 percent of the manganese from ore of the Dudley farm area, consuming 3.8 pounds of acid per pound of manganese extracted. Ores from the Littleton Ridge and Maple Mountain-Hovey Mountain areas were less amenable to this treatment, yielding approximately 80 and 60 percent of their Mn content, respectively. To increase the percentage extraction of manganese in the latter two ores, a number of factors were varied, including (1) acid concentration in the extracting solution, (2) ratio of acid to Mn in the slurry, and (3) preliminary heat treatment of the ore with a reducing agent. Other acids, including HNO3, HC1, and H2SO3, were tried also; however, no significant improvements in the Mn leached from Maple Mountain-Hovey Mountain ore were made. The manganese extraction of Littleton Ridge ore was raised to 90 percent by providing 9 to 11 pounds of HNO3 per pound of Mn in the ore.

Jan 1, 1954

By William R. Wayment, David E. Nicholson

The Bureau of Mines studied some physical properties of hydraulic backfills and their paramount characteristics , and made preliminary attempts to compact this type of material . The in- place density of hydraulic backfills affects the properties of strength , consolidation , and water percolation . Dense fills give better support than loose fills . In - place density properties themselves are affected by grain size , grain size distribution , and the particular conditions of sedimentation in a stope ( the amount of work the slurry water does to compact the material ) . Field sampling of in - place densities of fills presently used in four different mines and laboratory and underground compaction tests using a standard concrete vibrator show that the initial in - place density of the cohesionless fill material tested can be significantly increased by vibratory compaction .

Jan 1, 1964

By J. D. Tolman

In view of present interest in a revival of gold mining enterprises, papers dealing with the development of small gold properties are apropos. The present paper deals with the operation of a small gold property in the exploration and development stage, mining and milling 25 tons of ore daily, and indicates what may he expected in the way of mining costs under northern climatic conditions, by practicing rigid economy, at a property where disproportionate overhead costs are unavoidable bacause of the small rate of production. The output of this prospect is treated in a small amalgamation plant which has been described in a previous circular.. HISTORY Prospecting in the district was begun in 1909, and by 1911 the adjoining mines, Hollinger and McIntyre, were in operation. Actual work was begun on the Rochester claim in July, 1922, and carried on through 1924. The property was closed until 1928 when the present company took it over, together with the other holdings of the Canadel Mining Co. A small mill was started as a pilot plant on March 24, 1929, and is still in operation.

Jan 1, 1931

By F. E. Walker

The Bureau of Mines determined total sulfur and sulfur forms for coal in 283 counties in 29 States and 2 fields of the State of Alaska. Specifically, organic, pyritic, and sulfate sulfur were measured of approximately 2,900 samples, and they include most of the coalbeds in the United States.

Jan 1, 1966

By Ralph H. Whaite

To assist the anthracite industry obtain technical data on pneumatic packing, the Federal Bureau of Mines imported a pneumatic packing machine from Germany and installed it in a mine of a cooperating company in the Northern anthracite field of Pennsylvania. This report covers the second in a series of experiments in applying pneumatic packing for controlling strata movement (subsidence) above mine workings in the Pennsylvania anthracite region. The first experiment2/ was begun in January 1950, in a section of the mine where about 50 percent of the original coal remained in the form of pillars; since the company did not plan to mine the pillars in this particular area, pneumatic packing of the chamber voids was done for test purposes only. During this initial test the machine was operated on 204 shifts, and 652,400 cubic feet of breaker refuse material (22,834 tons) was packed into the voids of 16 chambers. The work was completed in December 1951.

Jan 1, 1956

By K. Shimamoto

This study has been prompted by the anticipated demand for rhenium by the petroleum industry and the concern for an adequate supply of rhenium to meet the demand. The present and projected outlook for rhenium relative to its distribution and occurrences, the recovery factors involved in ore beneficiation, capital and operating costs, changing technology, and the projected uses and market growth of rhenium are presented in this report as part of the Bureau of Mines program to determine the availability of recoverable rhenium in a developing market.

Jan 1, 1973

By A. W. Ambrose

"Those having an intimate knowledge of the relation between production and consumption of crude oil in the United States have realized for some time that production will not be able to keep pace with consumption. The American public has had this called forcibly to its attention by the increased prices of gasoline and crude oil, and by the recent shortage of gasoline on the Pacific Coast. In substance, each year we are consuming millions of barrels of oil more than we produce, and this deficit must be made to by importations. A careful analysis of the situation makes it evident that we need every barrel of oil that can be produced.Need for the Petroleum Production Engineer.Under present production practices perhaps 80% of the oil still remains in the sand. (See Lewis, J.O., Methods for increasing the recovery from oil sands, U. S. Bureau of Mines, Bulletin 148 p. 8.) Many wells are making water, and even whole pools are being flooded. The burning of fuels under field boilers is not generally efficient, and often gas is not made to do its full duty in bringing the oil to the well.In the past the producer has had to combat these and other problems single-handed. He has been too busy to give them special attention, and he has had little competent engineering advice. Oil, gas, and water occur underground according to certain natural laws. Undoubtedly an engineer, who is familiar with production practices and understands the fundamentals of the accumulation of oil and gas, can be of service to the producer by specializing on certain problems with a view of getting mare oil from the sand. In every other enterprise of similar magnitude the engineer is regarded as a necessary unit to its operation, and he should be so in the production of oil. His field of work should extend to every phase of production in which science and engineering and geology"

Sep 1, 1920

By John W. Buch

At a meeting of the Anthracite Investigations Advisory Committee in July 1944 at Washington, D. C., the initial work and objectives of the Anthracite Mechanical Mining Section of the Federal Bureau of Mines were discussed. It was learned that interest existed in an improved performance of mining thin, steeply pitching beds above the gangway by mechanical methods. One company offered the use of one of its mines for experimental work, and this offer was accepted. Following acceptance, an effort was made by Bureau engineers to devise a mechanical method with a performance better than that of a new hand method proposed by company engineers for an actual mining condition. The method proposed by the Bureau was to drive 30-degree slant chutes across a 10-foot bed pitching 85 degrees. These chutes were to be advanced by using a lightweight, compressed air-powered, shearing machine of German origin that had been tried in a flat Pennsylvania anthracite bed in 1934, and which did not then prove successful because of blasting difficulties. An attempt was made to obtain one of these machines from England, where it was known machines of this type had been used. Shortly thereafter John W. Buch was sent to Europe as a member of the Solid Fuels Mission to the European Theater of Operations organized by the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff. Through his efforts the Bureau of Mines obtained two such machines, known as the Eickhoff model DEK, one from England and one from Germany. This report covers the preliminary testing of these machines in order to obtain mechanical operating data for use in determining the power requirements for cutting anthracite with machines of this design.

Jan 1, 1949

By R. V. Higgins

As part of a study of application of the Buckley-Leverett method to an analysis of oil-reservoir performance covering a wide range of relative permeabilities and oil saturations, a method has been devised for quickly deter-mining average water saturation at breakthrough from relative permeability data. The base for the relative permeability used in the report is either the permeability to air or the effective permeability to oil at the irreducible water saturation. The permeability to air also was used because of the large backlog of air permeabilities available to reservoir engineers. The basic data were calculated by an electronic computer and are presented in a single graph from which the point of breakthrough may be obtained. In this study the water saturation at the beginning of the depletion is the connate or interstitial or irreducible water saturation. These water saturations are considered to be synonymous and to have a practical value.

Jan 1, 1960

By Franklin H. Persse

Domestic bismuth supply was projected from production figures for the ores in which it occurs--copper, lead, zinc, and tungsten. Published and unpublished data concerning host ores were examined to determine bismuth reserves and resources, and mine production. Potential recoverable bismuth occurring with reserves and resources of copper, lead, and zinc was estimated to be 36.3 million pounds. A bismuth availability diagram was developed from quantity estimates and ratios of production cost to value for these host ores. Additional recoverable bismuth occurring with domestic tungsten reserves was estimated to be 1.5 million pounds. Domestic byproduct production of bismuth will approximate 1.3 million pounds annually by 1980. This quantity will provide about 37 percent of the 3.5-million-pound estimated requirement for that year. Known world supply of bismuth appears to be sufficient for world demand to the end of this century. The study indicates that bismuth reserves and potential resources in the rest of the world have not been adequately reported.

Jan 1, 1970

By John Nagy

Dust explosion data obtained in laboratory tests by the Bureau of Mines are presented for 181 miscellaneous materials that present an explosion hazard. Data are given also for 50 dusts that present primarily a fire hazard and for 88 dusts that did not present an explosion hazard.

Jan 1, 1968

By M. F. Dunn

The objective of this work was to define jet fan performance in d variety of large cross-section underground mine applications and to develop guidelines for thin performance in open airways, dead headings, and multiple face areas. Measurements include common ventilation instruments, continuous recording remote electronic anemometers to measure air velocity, and sulfur hexaflouride tracer gas with chromatograph analysis to determine dilution rates and air recirculation. For open airways the following were determined: Large jet fans are leas efficient in smaller airways, but quite effective in larger open airways for achieving both uniformity end greater air entrainment, when inclined about 10° or elevated. For dead headings the following were determined: The jet fan must be placed against the rib of the heeding closest to the incoming airstream from the crosscut or recirculation will increase. The fan should be placed at the pillar corner to increase airflow. As the fan is moved closer inby, recirculation increases. Larger fans promote recirculation. Inclining fans about 12° improves airflow in large headings. For face areas the following were found: For panels having uncontrolled airflow, the fan should be placed in the incoming airflow, about one pillar inby, and directed diagonally across the faces. For panels having narrower rooms and controlled airflow, the fan should be placed alongside the panel side in the first room so as to direct or intersect the incoming airflow at the next entry or crosscut.

Jan 1, 1983