Search Documents

By G. H. Keith

Oxygen and nitrogen cause strain aging in electrorefined vanadium, as evidenced by maxima in yield and tensile strengths and by Snoek internal friction peaks. Alloys containing up to 0.22 percent oxygen and 0.11 percent nitrogen were investigated. Tensile strengths of oxygen-and nitrogen-containing alloys were 66,000 and 68,000 psi at 300° to 400° C, compared with 53,000 and 62,000 psi, respectively, at room temperature. Total elongation decreases to about 7 percent at the temperature of maximum strength. At 600° C, strain aging is not evident. Based on interstitial contents calculated from internal friction measurement, the increases in strength caused by nitrogen and oxygen were 440,000 psi per weight-percent nitrogen and 260,000 psi per weight-percent oxygen. Application of the Schoeck and Seeger treatment to the Snoek effect in these systems results in a calculated lattice distortion of 0.24 and 0.15 caused by the presence of an interstitial nitrogen or oxygen atom, respectively. Alloys containing boron or carbon were also investigated. Both elements refine the grain size but have no other effect because of their low solubility in vanadium.

Jan 1, 1969

By A. A. Berk

Other Federal agencies have been coming to the Bureau of Mines for help with the purchase and utilization of fuel, largely coal, almost since the day the Bureau was created in 1910. The requests covered a wide range of fuel- economy problems and included boiler-water treatment after it became apparent that water-formed deposits on heating surfaces acted as insulators, decreasing heat transfer and impairing fuel efficiency. Dr. Ralph E. Hall, a Bureau of Mines physical chemist determined the 3 reactions that cause adhering scale to form in boilers (7)2 and went on to introduce scientific principles into water treatment for scale prevention (8). Widespread publicity of these achievements increased the requests for help from Federal steam-generating plants. Since no other Federal agency (even those which were more directly concerned with testing water) wanted to provide boiler-feedwater service, the Bureau decided to continue to give requested help to Federal agencies, Later, the Congress endorsed such agency cooperation as an economy measure,

Jan 1, 1963

By A. A. Berk

Other Federal agencies have been coming to the Bureau of Mines for help with the purchase and utilization of fuel, largely coal, almost since the day the Bureau was created in 1910. The requests covered a wide range of fuel-economy problems and included boiler-water treatment after it became apparent that water-formed deposits on heating surfaces acted as insulators, decreasing heat transfer and impairing fuel efficiency. Dr. Ralph E. Hall, a Bureau of Mines physical chemist determined the reactions that cause adhering scale to form in boilers (7)2 and went on to introduce scientific principles into water treatment for scale prevention (8). Widespread publicity of these achievements increased the requests for help from Federal steam-generating plants. Since no other Federal agency (even those which were more directly concerned with testing water) wanted to provide boiler-feedwater service, the Bureau decided to continue to give requested help to Federal agencies, Later, the Congress endorsed such agency cooperation as an economy measure,

Jan 1, 1963

By Wing G. Agnew, John A. Johnson

"INTRODUCTION This paper is one of a series being published by the Bureau of Mines pertaining to an investigation on the use of stemming in metal mines now being conducted at the Mount Weather Testing Adit. Its purpose is to compare the amount of dust and gases produced as a result of blasting charges of dynamite (1) in drill holes, (2) in bombs, and (3) in mud-cap or adobe shots.ACKNOWLEDGMENTSValuable assistance and advice on stemming were given by members of the staff at the Bureau of Mines, as acknowledged in previous publications. 4/TEST PROCEDUREThe results used for comparison in this report are from dust and gas samples taken after blasting (1) four regular test rounds with no stemming, (2) five bomb shots, and (3) two mud-cap or adobe shots.The four rounds were the standard 26-hole test rounds designed to break 4 feet of rock. The procedure for drilling and blasting these rounds is described in Report of Investigations 3509.Before the regular test rounds were blasted, about 1,200 bounds of fine rock was placed on the steel mucking sheets that covered the end of the adit track; the wails, hack, and floor of the adit were washed thoroughly; and the fine rock on the mucking sheets was completely wetted.Each of the 5 bomb shots consisted of 10 sticks of dynamite tied together and hung at midpoint of the adit, 8 feet from the fall."

Dec 1, 1942

By A. J. Forney

A high-Btu gas was made at the Bruceton, Pa., laboratories of the Bureau of Mines to demonstrate the feasibility of using the gas as a nonpolluting fuel for automobiles. The pilot plants at Bruceton were revised to combine the processes of coal gasification, gas purification, and catalytic methanation in one overall system. Tests in the Bureau's test automobiles at Bartlesville, Okla., showed the Synthane gas was less polluting than natural gas.

Jan 1, 1972

By Jr. Taylor

The following heats of solution have been measured in 1.160 molal H2SO4 at 25° C: AH298, kcal./mole Be(c) + 77.44(H2SO4?47.849 H2O) H2(g) + BeSO4 (soln) -92.83 ± 0.11 BeSO4 ?(c) + 77.44 (H2SO4?47.849 H2O) BeSO4(soln) -16.45 ± 0.02 BeSO4?2H2O(c) + 77.44(H2SO4?47.849 H2O) BeSO4?2H2O(soln) -5.395 ± 0.019 BeSO4?4H2O(c) + 77.44 (H2SO4?47.849 H2O) BeSO4?4H2O(soln) 1.513 ± 0.010 Combining these data with other experimental results and data taken from National Bureau of Standards information yielded the following heats of formation at 298° K:

Jan 1, 1966

By A. B. Campbell

The mines in the eastern part of the now active region of the Tri-State zinc district of Missouri, Kansas, and Oklahoma have unusually acid water, which during periods of moderate or no rainfall is used in the mills to replace losses from evaporation, seepage-, and tailings disposal. Its use has caused difficulties by corrosion of equipment and by interference with flotation. The growing importance of flotation, which requires good water, and the increasing troubles caused by the corrosion of the milling equipment have prompted the Mississippi Valley Experiment Station of the United States Bureau of Mines, in cooperation With the Missouri School of Mines and Metallurgy, Rolla, Mo., to investigate the action of the waters on flotation and to undertake to develop means of obviating their harmful effects. The work was under the immediate direction of W. T. Schrenk, consulting chemist, United States Bureau of Mines, and professor of chemistry Missouri School of Mines and Metallurgy, and. Will H. Coghill., supervising engineer of the ore dressing section of the United States Bureau of Mines.

Jan 1, 1932

By M. R. Geer

All the coal lands in Alaska are publicly owned, and the Federal Government is the principal consumer of coal. Therefore the Government has long been concerned with the wise utilization of the coal reserves of Alaska as well as with the availability of coals meeting the specifications for use in various Government installations. Coal preparation plays a key role in both of these areas of interest. The proper choice and operation of coal-washing equipment permits the mining of inferior deposits, minimizes waste of coal in preparation, and assures a prepared product of the best quality obtainable from the raw coal. Thus, from time to time, the Bureau of Mines has made washability examinations on most of the coals mined in Alaska. Generally, these examinations were made when new mines or new beds were opened, when construction of new preparation plants was being considered, or when the operation of existing plants could be improved by better knowledge of the raw coal. The purpose of this report is to bring together all the washability data available on the coals of the Matanuska Valley and Beluga River fields. The pattern of energy development for the rapidly growing Anchorage area is not clear at this time. Formerly coal was the only fuel available for large-scale space heating and power generation. More recently both oil and natural gas have entered the market, and several hydroelectric projects have been completed. Additional major hydroelectric projects are being considered. The role that will be played by coal in this competitive energy market is uncertain. However I if coal is the fuel used in future power plants or industrial installations, the information contained in this report will be useful in indicating the quality of the coals that can be supplied and in selecting proper preparation techniques.

Jan 1, 1962

By Rudolf E. Greuer

Two computer programs for the real-time calculation of concentration distributions in the ventilation system of underground mines were designed. They allow one to simulate the movement of fumes or other contaminants with the ventilating air, the calculation of concentrations at any given point and time, and the determination of the total contaminant exposure at different places in the mine. Multiple and time variable contaminant sources can be handled and recirculation is no obstacle. The, first program is based on an airflow distribution which has, in the input data, to be stated. The second program has been linked to in existing program for the calculation of airflow distributions. Two versions of this second program are provided to accommodate the two existing programs. Several executed examples demonstrate the program performance.

Jan 1, 1981

By W. O. Vanderburg

This paper describing the methods of concentrating tungsten pros at the mills of the Atolia Mining Co. is one of a series of similar papers being prepared by the United States Bureau of Mines. The writer acknowledges the assistance and cooperation of A. V. Udell, president, Louis Warnken, bookkeeper, and C. K. Dennis, superintendent, of the Atolia Mining Co. in the preparation of this paper.

Jan 1, 1931

By Christopher D. Risbrudt

In this comprehensive study of the use of wood products in coal mining, a sample of over 220 mines provided data by questionnaire. Wood use per ton of underground coal was found to vary substantially by mining process and region. In the Eastern Coal region, 1.6 board feet of wood was used per ton of coal, wel above the 0.6 board feet usage per ton in the West. The kind of timber used varied also by Region. Hardwood use is about 40 times greater than softwood in the Eastern Region. There, hardwoods are plentiful, relatively cheap and strong. In the West where softwood forests predominate, softwoods were 2-1/2 times more common in mine wood use than hardwoods. Nearly 80 percent of the wood used in underground coal mines is used in cross bars and props. Nearly 54 million cubic feet of wood products were used in coal mining in the sample year 1979; about twice as much going to underground mines as surface mines. Wood requirements for mining were projected to 2030 for a range of three oil price scenarios. Much greater wood use will be required for greater coal output.

Jan 1, 1982

By H. J. Sloman

"INTRODUCTION Industry, including coal mining, has come to realize that to prevent accidents the human element must be given more consideration than was customary in the past. In formulating safety rules and regulations and in the enactment of laws governing mining, too often enforcement is emphasized rather than the means of gaining willing compliance.' The purpose of this paper is to call attention to the human side of accident prevention, and the approach to this important and much-discussed subject will deviate somewhat from the usual discussions.The human being is a complex mechanism, both physically and mentally. It is difficult to establish a common denominator for the actions of humans, except in general. In establishing mining laws, rules, regulations, and standards, the ultimate objective should be to gain the best possible response of workmen, so that optimum results in accident prevention may be obtained. The complexity of human beings is apparent when the many ways 1n which they differ are considered. Some of these differences are manifested in emotional and phlegmatic types, degrees of intellect or native intelligence; and in hopes, desires, aspirations, and philosophies of life. How much simpler ac¬cident prevention would be if the response to laws, rules, regulations, or standards were equivalent to the definite movements of puppets responding to pulls on strings. Each time, the strings are pulled in exactly the same way, the puppets will respond in exactly the same manner. Human beings, although having many similar characteristics, do not respond uniformly to identical ""string-pulling""; therefore, much study is necessary before the desired re¬sponses can be obtained. To achieve the ultimate in accident prevention, it must be ""worked at"" constantly. Regardless of the adequacy of safety laws, rules, regulations, or standards, good accident records will not ""roll in"" if dude consideration is not given to the personal traits of those most likely to be involved in accidents."

May 1, 1948

By J. E. Shelton

This presentation covers the results of laboratory studies conducted by the Bureau of Mines Mineral Dressing Section, Northwest Electrodevelopment Laboratory, Albany, Oreg., on alluvial sands from Dismal Swamp, Bear Valley, and Cascade, Idaho. The search for radioactive minerals has led to the reexamination of alluvial deposits; in the process of this reappraisal the frequent presence of minerals bearing columbium and/or tantalum was toted. Because of increased demand for these metals by the defense industries and because these industries depend upon foreign sources for their supply the domestic alluvial black sands are being considered, as a possible domestic source. However, utilization of these alluvial deposits depends upon development of methods of concentrating these valuable minerals. The primary objective of the test work was the study of the effect of attrition scrubbing, sizing, magnetic, electrostatic, and gravity separa¬tion as methods for concentrating and recovering the columbium and tantalum-bearing minerals, samarskite, euxenite, ilmenorutile, and columbite.

Jan 1, 1955

By Larry D. Nichols

Poroplastic membranes containing ion exchange liquids were studied for separating cobalt from nickel-containing solutions similar to ammoniacal laterite leaches. The driving force for cobalt transport was differences in pH and composition between the leach and extraction streams. Using a diketone ion exchange liquid, a leach pH of 6.5 to 7.0, and a strip pH of 2.3, cobalt was extracted from a 750 ppm solution containing 2500 ppm of nickel at rates ranging from 1 to 10 µg/cm2 .min in single membrane cells, and from 10 to 100 in more closely spaced multiple membrane cells. Rates were variable, with evidence that cross -membrane flow pasterns were a key factor; a reproducible rate of 30 pg/cm .min would be economically viable. Loss of transport observed after several days of continuous operation was restored by flushing membranes with fresh ion exchange liquid. A major effort was devoted to preparation of thin, leak-free membranes; the resulting membranes endured operating conditions without mechanical failure.

Jan 1, 1982

By F. Varley

Researchers from the National Institute for Occupational Safety and Health (NIOSH), in cooperation with mine operators, conducted a study of heat stress exposures among mine rescue workers in underground mines. Mine rescue workers face extreme heat loads as they enter hot and poorly ventilated environments, particularly when they are wearing breathing apparatuses. The burden of wearing a closed-circuit breathing apparatus (CCBA), the inability to drink fluids for extended periods of time, and the potential for ventilation disruptions and fires combine to increase the risk of heat illness during a response to an emergency. In this research, ambient environmental conditions and heat strain indicators were measured using conventional ventilation monitoring tools during mine rescue training exercises. Heat strain was measured with an ingestible temperature-sensing pill that measured core temperature continuously. In addition, a heart-rate monitoring chest strap was used to indicate physical strain resulting from physical activity and heat. Both core temperature and heart rate data were transmitted to a remote recorder worn by a rescuer and time-stamped. Team activities were also observed to determine the contribution of work rate to a person’s total heat load. The effectiveness of several engineering controls, such as cooling the air inhaled by rescuers through an apparatus, wearing cooling vests, and supplying water through the CCBA masks, were investigated. Administrative controls, such as limiting the duration of exposure and controlling the work rate through forced-rest regimens, were also evaluated. Results to date are discussed, and tools for evaluating team condition and estimating the length of time it would be safe for rescuers to work are proposed.

By K. R. Van Doren

The polynomial method for estimating virial coefficients from experimental data suffers from three serious defects: (1) There is no known relationship between the polynomial coefficients and the virial coefficients, (2) the values of the estimates depend upon the degree of the polynomial and the particular set of values used for the independent variable, as well as the random errors in the dependent variable, and (3) the variances calculated for the estimates do not represent the mean square errors of estimation. Attempts to overcome these defects have thus far been unsuccessful; these attempts have also failed to account for the fact that none of the virial coefficients are uniquely determined by the values of the dependent variable for a finite set of values of the independent variable. The conclusion is that virial coefficients cannot be reliably estimated from experimental data unless additional information about the virial expansion itself, such as its rate of convergence, is available.

Jan 1, 1969

By Daniel D. Sweeney

The United States coal mining industry has traditionally experienced difficulty in controlling dust levels below the occupational exposure limit. While improvements in face ventilation and water spray nozzles have decreased dust exposures, approximately eight percent of experienced coal miners are still developing Coal Worker?s Pneumoconiosis. This investigation tested the feasibility of enhancing existing engineering dust controls by mounting a simple barrier on a longwall shearer that separated the operators from the cutting drums. The barrier was constructed and tested above ground at the National Institute for Occupational Safety and Health Pittsburgh Research Laboratory longwall gallery test facility. A 96-percent reduction of respirable dust occurred at the headgate sampling position when tested at 2.4 m/sec (480 ft/min). The average dust level decreased from 39 mg/m3 to 1.5 mg/m3 by utilizing the barrier.

Jan 1, 2009

By R. H. Grau, S. B. Robertson, R. B. Krog, T. P. Mucho

Due to the difficulties of ventilating large opening stone mines, the effective dilution of diesel particulate matter and noxious gases has often been problematic. Since stone mines have large openings that develop low air resistances, and propeller fans are designed for low pressure-high volume applications, main mine propeller fans may be a feasible option for ventilating underground stone mines. This paper describes the results of a case study where researchers from the National Institute for Occupational Safety and Health have demonstrated that significant increases in total mine airflow can be achieved and the ventilation improved in a large-opening stone mine by replacing an axial-vane mine fan with two 12-ft diameter propeller fans and adding a line of stoppings. In this study, the use of the propeller fans more than doubled the air quantity from 300,000 cfm to 750,000 cfm, while operating at 50 horsepower less than the original axial-vane fan.

By Robert C. Ellman

Stockpiles containing 2.3 million tons of lignite constructed in the period 1948-56 in conjunction with the construction of Garrison Dam on the Missouri River demonstrate successful stable long-term storage of lignite. Uniform and thorough compaction of each of the I-foot-thick layers by which the piles were constructed produced a bulk density of 70 Ib/cu ft. Air penetration into the stockpiles was restricted to a degree that prevents spontaneous heating or deterioration of the stored lignite, A continuing record of observations beginning with stockpiling operations in 1948 has been accumulated, This includes periodic fuel analysis, analysis of pile gases, and measurement of pile temperatures on the first large stock-pile, pile 5. This report describes the stockpiling method, the changes in heating value, pile gas composition, and pile temperature and summarizes observations from 1953 to 1964, Data accumulated attest to the stability of the stored lignite. The variation of the average heating value of periodic pile-depth samples is only 160 Btu/lb (11,990 to 11,830) on the moisture" and ash-free (maf) basis during almost 10 years of storage. Temperature levels of the pile interior are progressively decreasing. At pile surface, cyclic variations occur with the season. The only problem encountered with the large stockpiles is wind and water erosion of the pile surface. The partially successful control measures used are described.

Jan 1, 1967

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

C 6 Automatic Elevator Control Systems An automatic elevator control system, consisting of position sensing devices and a control unit, can be used to control an emergency mine hoist. While automatic elevator control systems are assembled from standard components, they are typically custom designed to suit a given customer's application. Various manufacturers contacted indicated that the price range, less installation, for a simple two-stop control system begins at approximately $2500 and can increase depending upon the type of components used, shaft depth, the type of mechanical drive used, and the maximum operating speed A partial list of elevator control manufacturers follows. They should be contacted for further details. Marshall Elevator Company Pittsburgh, P A 412 -431 -1340 Armor Elevator Company, Inc. Louisville, KY 502-361 -7181

Jan 1, 1976