Search Documents

By Gordon L. Kinney

The only economically important mineral currently produced in Bangladesh was natural gas. Bangladesh was not a world? ranked producer of any mineral commodity, but the possibility of producing and exporting commercial amounts of liquefied natural gas (LNG) was being examined. Proved reserves of natural gas were sufficient to supply most of the country's industrial and domestic heating and electric needs and still support an export-oriented LNG plant. Other mineral production was of virtually no significance to the economy, although there were a few prospects for nonmetallic mineral development. Bangladesh continued to make economic progress during 1978 and into early 1979. Gross domestic product (GDP) at current prices rose from $6.6 billion in 1976-772 to $8.2 billion in 1977?78 and $9.3 billion in 1978.79.2 In fiscal 1979, the economic conditions were favorable until a severe drought hit most of the country. It W88 reported that conditions were the worst in 40 years, and 88 of July 1979, substantial crop losses were predicted. The agricultural sector accounts for over 53% of the GDP and about 75% of all employment. The poor weather will cause economic problems in the form of slower growth, larger trade deficits, and a higher rate of inflation. The 1978.79 statistics showed that real GDP increased just 4%.

Jan 1, 1981

By J. D. Dixon

This Bureau of Mines report describes a technique for determining the confining pressures that must be provided for stabilizing underground openings in incompetent rock. The technique is adapted for use with a nonlinear finite-element computer code, NONSAP, to obtain stabilization pressures for linear or nonlinear stress distributions in the rock media around the excavation. This analysis permits a point-wise calculation of active rock pressures that depend on the values of shear stress and strength along the excavation surface. The approach is applied to the solution of several sample problems. The results show that both the magnitude and the distribution of stabilizing confining pressures are significantly influenced by rock and joint strengths, joint orientation, and biaxial nature of the load field.

Jan 1, 1976

By J. G. Donaldson

Optimum conditions are given for chloridizing pyrite, marcasite, chalcopyrite, arsenopyrite, stibnite, and covellite with chlorine gas. The formation of metal chlorides is affected by the time and temperature of chloridizing, and by particle size of the sample. Chloridizing data also are given for chemically precipitated antimony (III) sulfide and copper (II) sulfide.

Jan 1, 1962

By Suresh K. Bhatt, Christopher Mark

Fatalities caused by highwall/spoil bank failure in the surface mines, coal and non-metal, increased to an alarming rate of seven during 1999. To determine the causes of slope failure and successful mining practices, the National Institute for Occupational Health and Safety undertook a study. The study included: 1.A review of accident statistics; 2.A review of Federal and state mining laws pertaining to surface mining; 3.A literature review, and; 4.Mine visits. The study emphasized surface mines in the states of West Virginia, Ohio, and Pennsylvania. The review of a decade’s accident statistics using the mine Safety and Health Administration’s (MSHA) database showed that approximately 40% of all ground control related incidents reported to MSHA occurred in just four eastern states: Kentucky, West Virginia, Pennsylvania, and Ohio. The comprehensive literature search provided a historical perspective of highwall stability issues. Eleven mines we visited to obtain data on their mining practice or design. Commodities included coal, sandstone, and limestone. Based on the visits, five case studies were developed to represent typical mining methods and effective ground control practices used in eastern surface mines. Benching was found to be a common technique to reduce the overall highwall slope angle. Decking in the softer zones, such as shale, proved useful in controlling damage due to blasting.

By B. W. Gandrud, A. C. Richardson

"INTRODUCTION The Bankhead mine of the Cane Creek Coal Mining Co. is in the central part of Walker County, Ala., 4 miles south of Jasper. The Mary Lee bed in this part of the State yields a practically free-burning coal which is marketed as a. steam-raising and domestic fuel. As mined, the coal ordinarily contains ash-forming impurities to an extent that makes it necessary to treat the coal by some washing process before it is marketed. At present the Bank-head coal coarser than 3-1/2 inch is hand-picked and the coal finer than 3-1/2 inch is washed in two single-compartment jigsThis paper contains the result of screen-sizing and float-and-sink tests on a representative sample of the run-of-mine coal and the results of tests made to show the amount of coal liberated from impurities by crushing the coarser sizes. .This report is one of a series on the washability of Alabama coals which is being prepared by the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the coal producers of Alabama.SAMPLING AT THE MINE'The Mary Lee bed at Bankhead consists of two benches separated by a rock parting which varies in thickness from place to place in the mine. The top bench has a very uniform thick-nest; throughout the workings and yields about 65.0 per cent of the output. The bottom bench varies greatly in thickness and in nary places becomes too thin to work at a. profit. The sample for the washability study was taken underground at a place which was typical of the mine as a whole. In taking the sample the working face was squared up and a representative section out from each bench. Care was taken to secure a, quantity of coal from each bench proportional to the quantity contributed to the mine output. The rock parting as gobbed in accordance with the usual mining practice. The total sample taken weighed 3 tons."

May 1, 1933

By E. Chin

The domination of Bangladesh's mineral industry by natural gas was in for some possibly significant changes. A modest flow of crude oil was struck in a gas development well in the northeastern corner of the country. This was the first commercial flow of crude oil in Bangladesh. All crude oil was being imported, which cost a significant proportion of the nation's foreign exchange earnings. The development of an oilfield producing only a few thousand barrels per day would be a welcome help to the economy. Additional exploration at a 1985 coal discovery in the northwest indicated a considerable reserve of good-quality coal at a depth suitable for mining. If the coal is mined, it would be a boon to the local economy because natural gas was not available in the area.

Jan 1, 1988

Reduce dust at the auger mine face by modifying airflow patterns, around the minim machine. Approach Limited clearance between an auger miner and the mine root restricts airflow across the face and causes dust rollback. Directional sprays arc used to direct air across the face, thereby reducing dust rollback and increasing dust dilution (fig. 1). Laboratory and underground studies were used to test and optimize effectiveness of the directional sprays. Results of Laboratory Study Laboratory experiments were conducted in a simulated auger gallery equipped with a full-scale mock auger miner and bridge conveyor. A dual curtain configuration was used to direct the, ventilation, which averaged 2,700 cfm throughout the experiment. Testing variables included spray location, pressure, spacing, orientation, and number. Figure 2 shows the optimized directional spray system, also called the auger clearer spray system. The system consists of three sprays mounted alone the intake side of the miner. Sprays arc spaced 16 to 24 inches apart, and angled 30° toward the return side of the miner. The 24-inch spacing moved about 7% more air across the face than the 16-inch spacing; however, it resulted in some additional misting on the return side of the miner. A 30° orientation was more effective than a 60° orientation for moving air across the face and minimizing misting on the return side of the miner. Flat fan sprays arc used because their spray paths arc not obstructed by the top of the miner and mine roof, A 50° fan angle is used to minimize misting on the intake side of the miner.

Jan 1, 1989

By Verne S. Mutton, William A. Slivensky, Eric S. Weiss, Kenneth L. Cashdollar, Deepak R. Kohli

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, cooperated with Tecrete Industries Pty. Ltd. and BHP Australia Coal in a research program to evaluate the strength characteristics and air leakage of four seal and two stopping designs for use in underground coal mines. A fundamental safety research area for NIOSH is to eliminate the occurrence of coal mine explosions or to mitigate their effects. One approach to achieve this goal is to develop new and innovative seal designs that provide increased explosion isolation protection for the mining personnel against ignitions that originate from within the gob or. other worked-out areas of the mine Full-scale seals and stoppings were constructed in the Experimental Mine at Lake Lynn Laboratory near Fairchance, Fayette County, PA. They were ail--leakage tested, then subjected to a series of explosions with average pressure pulses ranging from 25 to 500 kPa (3.5 to 72 psi). Instrumentation measured seal displacement and acceleration as a function of time, providing data to assist in the development of numerical models 1'01- future seal design. All three seals designed with Meshblock wire forlnwo~-k ant1 a lnonolithic shotcrete core withstood the first explosion test, which generated an avcr-age rnaximu~n pressure of - 140 kPa (-20 psi) while maintaining acceptable air leakage rates. These seals I-anged from 175 to 325 mm thick. They included a 2.7-m-high by 325-mm-thick seal that was tesled 27 hr after completion against this - 140-kPa explosion pressure, a special requirement of the test program. This seal survived explosions with pressure pulses up to 300 kPa (43 psi). The 2.3-m-high by 325-mm-thick Meshblock seal survived three explosion tests with overpressures up to 455 kPa (66 psi) and satisfied the air leakage criteria. A I ,200-mm-thick plug seal was constructed of two Gunmesh formwork walls in-filled with shotcrete and a 3,450-kPa (500-psi) strength Aquablend core. This plug seal survived three explosions with pressure pulses ranging 11-om 150 lo 430 kPa (-22 to 62.5 psi) with no measurable postexplosion air leakage. Two Gunmesh stoppings with thicknesses 01' 40 and 75 inln withstood explosion overpressures of 23 and 115 kPa, respectively. Anchoring all seal and stopping designs into the roof, ribs, and floor with steel "rootbolts" provided very effective boundary constraint that is critical to the performanceofstructures subject to explosion overpressures.

Jan 8, 1999

By Michael S. Wieland

This report investigates whether it is tractable and thereupon reasonable to remove the booster influences when ranking the toxic fumes of non-cap-sensitive mining explosives. The hazard potential is represented by relative fume toxicity RFT, the resultant influence computed from a formulated rule with a restricted set (tally) of fume components and multiplying constants. The RFT result is compared to the rule criterion that represents the worst case tolerable toxicity stipulated by regulations or otherwise. The typical nonstoichiometric booster composition can render notable unwanted influence on the RFT ranking results. Historically, the remedy was to shoot the booster separately and reduce the trial concentrations by the relevant subtractions. Unreal negative concentration results were noted on rare occasions, revealing the faulty nature of the reduction procedure. With thermodynamic reaction chemistry codes TDRC, on the other hand, the booster ingredients can be retained in or removed from the reactant tabulation, yielding reduction factors taken as the concentration ratios for the two circumstances. The underlying presumption regarding reduction factors is that the ratios of component concentrations with and without the booster ingredients when resolved theoretically ought to equal those rendered experimentally, when tractable. Upon rearranging the presumed relationship, the unadjusted fume concentrations divided by theoretical reduction factors yield the wanted readjusted fume concentrations, thereby removing the booster influence without generating unreal negative concentrations. The work principle from thermodynamics restricted by the constraint of zero-net interaction loss is utilized in conjunction with the TDRC to resolve the wanted (Z-state) fume spectrum. This circumvents the recognized difficulty with traditional hydrodynamic detonation theory that is related to the nonideal reaction characteristics of typical mining explosives. The tacit characteristic of the Z-state resolved from the non-trajectory work principle is that it can not be remedied or tampered with, unlike the traditional trajectory techniques where the reaction products can be readjusted by changing formula representations, nullifying specific reactions or otherwise manipulating the thermodynamic trajectory process. Though the work principle theory is an unfinished formulation, the Z-state results prove worthy enough for rendering trends and comparisons and reaching otherwise useful conclusions. Further refinements should yield more reliable fume spectra and indicate explosive composition readjustments that would reduce toxic effects within underground mines and the wider world environment.

By David R. Forshey

This Bureau of Mines report presents a quantitative theoretical analysis of a coupled gasdynamics-heat release system involving the kinetics of water condensation in and behind the rarefaction wave in a shock tube using the method of characteristics. The merger of characteristics to form a shock wave is included.

Jan 1, 1977

Provide an accurate, reliable means for determining when a sealed mine or mine section can be safely reopened after a fire. Approach The Bureau of Mines performed a research investigation that resulted in the development of a mathematical formula for deriving a quantity, called RATIO, which can be used to define when a sealed mine or mine section has returned to safe recovery conditions after a fire. Research Results There were two major results from this Bureau research. Over a period of several years, the Bureau of Mines conducted six experiments at its Bruceton Experimental Mine in Pennsylvania. The experiments involved sealing the mine after several tons of piled coal had been allowed to burn continuously for 2 to 3 days. Although gas data obtained during the experiments revealed nothing significant, measured smoke particle levels were found to correlate with the stages of combustion and temperatures of the smoldering coal pile. Moreover, it was found that no smoke particles are produced when high-temperature smoldering exists deep within the mass of the coal pile since the smoke particles are filtered by the coal surrounding the hot region. Smoke is emitted into the mine atmosphere only if combustion is occurring near exposed surfaces. As suggested by these findings, any decision to recover a sealed mine area based primarily upon the absence of smoke particles is not a wise derision.

Jan 1, 1988

By Richard L. Sayrs

"The Stiner zinc prospect near the north boundary of Union Tennessee, and the Bunch Hollow property 5 miles northeast in Claiborne County, Tennessee, were diamond-drilled by the Bureau of Mines during the period .September 1, 1944, to February 22, 1945. Seventeen holes totaling 5,687 feet were completed, 13 of which, totaling, 5.083 feet, were on the Stiner property and the remainder, totaling 604 feet, at Bunch Hollow.The Stiner prospect is about 1 mile east of the old workings known as ""New Prospect"" or ""Lead Mine Bend."" The Federal Geological Survey made a study' of the area early in 1944. The prospect was first visited in August 1944 by Bureau of' Mines engineers3/ accompanied by members of the Federal Geological Survey.4/ The locality is reached by traveling State Road 33 north-about 9 miles from Maynardsville, Tenn., thence northwest about 7 miles by an improved county road that leads to the mine (fig. 1). The tract comprises an area of about 181 acres held by G. S. Stiner of Sharps Chapel, Tenn.; it is now under option to the Universal-Exploration Co. of Jefferson City, Tenn.The Bunch Hollow property, about 5 miles northeast of the Stiller prospect, was also studied by the Federal Geological Survey previous to being;Visited by Bureau of Mines engineers in August 1944. It is reached by traveling north from Maynardsville, Tenn., on State Road 33 about 13 miles, thence northwest by county road 6 miles to the property (fig. 1). The last 3 miles of the county road are in poor repair but are passable during the entire year. The property comprises an area of approximately 300 acres and is held by the imperial Mining Co., Pressman's Home, Tenn.Few reliable data are available as to the history of the Stiner prospects themselves. However, the New Prospect mine, 1 mile west, has had a colorful past, This mine was opened in 1883 and was worked intermittently until 1918, by which time more than 65,000 tons of concentrates had been shipped. No further work was done until 1942, when the mine pillars were robbed and 1,900 tons of ore averaging 25 percent zinc was shipped to the New Jersey Zinc Co., Austinville, Va."

Apr 1, 1946

By Alfred E. Schwaneke

The surface tension from 240° to 844° C and the density from 236° to 583° C of 99.999 percent purity liquid tin has been measured using the maximum-bubble-pressure method. Results for surface tension (y) show y (dynes/em) = 566.84 -4.76 X 10-2 T (° C) with a standard error of 1.9 dynes/cm. Results for density (p) show p (g/cm3) = 7.16 -6.3 X 10-4 T (° C) with a standard error of 0.012 g/cm3. Comparisons with other data found in the literature are discussed. The experimental results are considered to be as good as any data presently available.

Jan 1, 1970

By Donald W. Mitchell

The fire hazard of neoprene, polyvinyl chloride, and rubber conveyor belts was studied at the Federal Bureau of Mines Experimental Coal Mine. The effects of intensity of ignition source, velocity of the ventilating air, and type of belt were investigated at three levels in small-scale gallery experiments. Studies were made in the mine on the effects on ignition and flame propagation of belt-entry dimensions, belt widths, and belt configuration. Methods for extinguishing belt fires were also investigated under simulated mining conditions, and during these trials coal dust and grease were placed on the belt. The research showed that conveyor belts will burn. Neoprene, polyvinyl chloride, and rubber belts, with and without carcass, ignited and propagated flame. The highest rate of flame propagation was obtained on rubber belt. The fire hazard increased with increase in intensity of ignition source and air velocity. Flame propagated only when air was forced through the test zone; propagation was not obtained when forced ventilation was not used, as would exist in a neutral entry in a mine. Automatic water sprays and high-expansion foam effectively arrested flame propagation; direct application of water and bicarbonate dusts was ineffective.

Jan 1, 1967

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of the significant coalbeds of the Ohio coalfield. Washability analyses were made on 39 coalbed samples collected from a 14-county area. None of the samples were of metallurgical quality as received. Nine of the samples could be sufficiently upgraded to produce metallurgical-grade products, and the remaining 30 samples could not be upgraded to this quality because their sulfur contents could not be lowered to meet the standard. For steam or power generation, 10 of the samples were of medium sulfur content as received and one could be upgraded to a low sulfur content. Of the 29 samples having a high sulfur content as received, 18 could be upgraded to a medium sulfur content. The original sulfur content of the other 11 samples having a high sulfur content as received can be appreciably reduced by removal of the sink 1.58 specific gravity material; however, these coals would be classified as high sulfur coals both before and after removal of the sink 1.58 specific gravity material.

Jan 1, 1972

By Sanford J. Douglas

This publication describes a study by the Federal Bureau of Mines of devices and methods used for testing and splicing 4,160-volt and 440-volt cables and for providing ground-fault protection for 440-volt circuits, as developed and used by the electrical staff of the Tecumseh coal mine, an open-pit operation at Boonville, Ind. The testing and ground-fault devices described should find ready application in other open-pit mines, and, with suitable modifications for voltages involved, in underground mining. The devices and testing methods are based on sound engineering principles and are time-tested and economically feasible, Four devices are used: A high-voltage tester, and a low-voltage high- current tester, both for testing 4,160-volt cables; a tester for 440-volt cables; and, electronic ground-fault protective device for 440-volt cable circuits. All the cable testers and the grounding device were designed and built at the mine from standard parts. They are inexpensive, dependable, and job tested, An attempt has been made here to describe them in enough detail so that interested persons can assemble duplicate units.

Jan 1, 1960

By S. H. Ash

For several years considerable activity has been devoted to economic and social factors affecting California metal-mining operations as they relate to accidents and their cost. The reason for this intense interest is that accidents cost this industry annually over $1100,000 in industrial insurance premiums for mines insured by insurance carriers only; during 1924-32, inclusive, they amounted to $3,616,9115. There are several reasons for this high cost, the most important of w rich are the consistently .high frequency and severity rates of injuries occurring in the industry. Coordination of effort, appreciation of a mutual problem, and widespread education are essential if accidents and their cost are to be reduced.

Jan 1, 1935

To reduce air be respirable dust generated from emptying dry dust collectors on small truck-mounted drills used at surface coal mines.

Jan 1, 1995

By G. Nuñez, M. A. Pathak, C. F. Stanley

"Holographic interferometry is a non-destructive technique to detect small deformations1 of an object. It is a whole-field technique· with an accuracy of a few microns. An adaptation of holographic interferometry is time-averaged holographic interferometry which is particularly useful in detecting small vibration amplitudes of an object under investigation. Its application to biological tissue is especially difficult due to the combination of (a) the high sensitivity of the technique, and (b) the tendency of these objects to deform excessively, or move during the testing period. (This is also compounded by the changing moisture content of the tissue surface.)Ideally, a pulsed laser and fast-acting thermoplastic film camera could be chosen to overcome these difficulties, but the total equipment cost could exceed $75,000. In this paper we describe our relatively economical method to apply time· averaged holographic interferometry to an excised animal lung, utilizing holographic plates and a mechanically-shuttered continuous-wave Argon laser.EXPERIMENTAL METHODThe schematic of the experimental setup is shown in Fig. 1. The holographic equipment, including the laser, is fixed on a 3 ft x 6 ft x 4 in. honeycomb holographic table. This table is functionally similar to one described by Mark and Horsch2 which can be constructed for about one thousand dollars. The holographic table itself rests on six inner tubes to absorb floor vibrations. All unnecessary vibrations must be reduced to preserve the quality of the holograms. A laser beam from a 0.5-watt continuous-wave Argon laser is split by a circular variable beamsplitter (Newport Corporation Model 50GOOAV.1) into two beams, i.e., an object beam and a reference beam. The object beam is again split into two beams of equal intensity by a 50150 beamsplitter (Newport ·Corporation Model BS.1). These beams are optically filtered and expanded by spatial filters (Newport Corporation Model 910) to cover as much area of the object as possible. Soft biological tissues exhibit low reflectives, resulting in a relatively high reference to object beam ratio of roughly 5 : 1 at the holographic plate."

Jan 1, 1989

By Thomas C. Ruhe

The Bureau of Mines conducted research to determine the safe operating conditions for using recycled (used) lubricating oil from mining equipment as a partial replacement for diesel fuel to make ANFO-type blasting agents. The use of recycled oil (RO) saves energy, reduces oil imports, and reduces mining costs. Low ambient temperatures may cause these recycled oils to become too viscous for proper absorption by ammonium nitrate (AN) prills and result in poor blast performance, safety hazards, and environmental problems. To help quantify and resolve these issues, viscosity, mixing, and performance tests were conducted at various temperatures. Diesel fuels No. 1 and No. 2 were studied separately and in blends with 25,50, and 75% RO. Good quality ANFO mixes (94-6) were produced with dry absorbent prills and blended fuel (No. 1 diesel plus RO) at temperatures as low as -40° F (-40°C) with 75% No. 1125% RO, and at -20°F (-29°C) with 50/50. Diesel fuel No. 2 also made good mixes as low as -30" F (-34" C) with 75% No. 2/25% RO, and at 0° F(-18° C)with 50/50. Reference detonation velocity tests were conducted in 1.4" (3.6 cm) diameter steel pipe at 70°F (21°C) on No. 1 diesel ANFO (94-6), giving an average value of 9722 ft/s (2964 m/s). Comparison tests showed good ANFO performance at low temperatures. Blended fuel ANFO (75% No. 1/25% RO) mixed, loaded, and tested at -40°F (-40°C), produced an average velocity of 9247 Ws (281 8 m/s). A 50/50 blend gave a velocity of 8083 Ws (2464 ds) at -20°F (-29°C). Based on these results, a practical field method has been developed to help evaluate whether a specific oil blend will mix properly with AN at a low ambient temperature. This method will help to promote the safe and reliable use of RO ANFO at low temperatures, with adequate performance.

Jan 1, 2008