Search Documents

By Julian Vigil

Mountain bumps have been a problem in the coal-mining industry since the 1920's. The problem became severe in the late 40's and early 50's with the introduction of mechanized mining. Fatalities and serious injuries resulted from mountain bumps during this period. Mountain bumps again caused fatalities in the 80 's. Interviews were conducted mostly with retired coal miners having experience in bump conditions with five different coal companies. These men held positions as president, general manager, roof-control specialist, mining engineer, inspector, superintendent, mine foreman, shift foreman, section foreman, miner operator, electrician, and general laborer. Together, their comments give a good idea of the things tried to mitigate mountain bumps in the Appalachian Coal Fields.

Jan 1, 1991

By Kenneth Trelewicz

This report describes the total effort that went into developing environmental test criteria for general mine instrumentation. The project was a two-phase effort. Phase I consisted of research and mine visits to develop an environmental profile for mine instrumentation. The profile was translated into general requirements and then into test requirements. A review of existing government and commercial specifications was performed to determine if they matched mine instrumentation test requirements. Finally, a set of environmental test procedures was developed for the testing of mine instrumentation. Phase II consisted of selecting and purchasing sample mine instrumentation and subjecting them to the previously developed tests. The purpose was twofold: (1) to evaluate the criteria developed for use as an instrumentation test document and (2) to determine the effects of the various criteria on a representative sample of both proven and newly developed instrumentation. The test criteria were then modified, based on the results of the testing, and are listed therein.

Jan 1, 1981

By D. J. Dollhopf

This research was part of an effort to investigate means of reestablishing non¬polluted hydrological systems in areas where surface mining directly impacts shallow ground-water resources. Chemically undesirable overburden material was selectively backfilled with the intent that it would be below the future root zone, be above the reestablished aquifer, and would not be leached as a result of deep percolation. After 2 years the buried material remains above the spoil aquifer and below the maximum rooting depth. Unsaturated water flow from the land surface to the buried material occurred during wet climatological periods. No significant leaching of buried material was observed, however. Overburden sample contamination from drill stem joint grease with Pb, Zn, and Cu additives caused substantial error regarding DTPA extractable trace metals. A grease with teflon and talc additives was recommended for use in future sampling programs. DTPA extractable trace elements in overburden material had no statistical relationship to post-mine ground-water quality. Overburden columns leached with water produced leachates comparable to overburden and spoil ground-water trace metal quality. A depositional model described the Rosebud Coal overburden as a fluvial system with distinct units of sand, silt, and clay, with distinct chemical properties. Physical and chemical characteristics of the model were comparable to the in situ geochemical system, a relationship which may aid in locating overburden materials unsuitable for reclamation.

Jan 1, 1979

By Frank D. Lamb

Four samples of manganese-bearing material from the Aroostook County, Maine, deposits were tested at the Eastern Experiment Station of the Bureau of Mines at College Park, Md., to determine their amenability to beneficiation by ore-dressing methods. The samples represented material from the Maple Mountain-Hovey Mountain deposit, the Dudley farm, and the Burnham farm and contained 11 to 14 percent manganese. None of the tests produced appreciably enriched concentrates suitable for further treatment for the production of ferromanganese. The intimate association of the manganese minerals with iron and siliceous minerals requires extremely fine grinding to liberate the manganese minerals in these ores and prevents efficient concentration by physical means.

Jan 1, 1953

By X. Chi, J. W. Griffith, C. L. Schengrund, J. Sabol

"Experiments were carried out to determine the long-term effect of instillation of 500 mg of generic bituminous, anthracite, quartz, or titanium dioxide (Ti02) dust on the composition of pulmonary surfactant. Dust was instilled in the caudal lobe of the right lungs of female pigtailed macaque monkeys (Macaca nemestrina). The composition of surfactant isolated from cell-free bronchoalveolar lavage (CF-BAL) samples obtained from right lungs (dust exposed) at various times over the following year was compared with that of surfactant isolated from CF-BAL from left lungs (dust free) . Little change was seen in the amount of surfactant-associated lipid phosphorus as a result of exposure to dust. Exposure to quartz, anthracite, or Ti02 dust induced a significant increase in the total amount of protein in the surfactant-enriched fraction. The relative amount of specific proteins was also altered: surfactant-associated protein A decreased, and the amount of the heavy and light chains of immunoglobulin molecules (identified by NHiterminal amino acid sequence analysis) increased. These changes were visible more than a year after instillation of quartz and at least 3 months after instillation of anthracite dust. Despite variation in the responses of the individual animals, the changes observed might serve as an indicator of the severity of the effect of exposure of the lung to mineral dust and/or to pathogens. IntroductionSurfactant is essential for normal pulmonary function and gas exchange. It functions to reduce surface tension and may help to prevent pulmonary edema [19] and to protect against infection [13]. The importance of surfactant to normal Jung function is illustrated by the fact that neonates lacking appropriate surfactant undergo respiratory distress and do not survive without clinical support."

Dec 1, 1996

By D. C. Dahlin

The Bureau of Mines conducted laboratory batch beneficiation tests on samples from four potential platinum resources in southeastern Alaska to concentrate platinum and other precious metals. Thin Investigation was done as part of the mission of the Bureau to insure an adequate supply of minerals to meet the Nation's needs. Petrographic studies and beneficiation methods including gravity concentration, froth flotation, and magnetic separation were used to determine mineral association and to attempt to concentrate the platinum values with a primary mineral value such as chromite, copper sulfide, or magnetite. A high-graded sample from the Salt Chuck copper sulfide deposit yielded the platinum-group metal concentrate; the maximum grade attained was 0.04 oz Pt and 1.5 oz Pd per ton of high-grade copper sulfide concentrate. The other samples yielded low-grade primary mineral concentrates with low platinum-group values, and/or the platinum-group metals did not concentrate with the primary mineral value.

Jan 1, 1981

By Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as “Good” to “Very Good” using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.

By F. D. DeVaney

The low-grade deposits of manganese ores along the Missouri River near Chamberlain, S. Dak., are known to contain one of the largest reserves of manganese in the United States. Manganese occurs as concretionary nodules ranging in size from 13 inches in their longest dimension to particles finer than 65-mesh. The nodules are embedded in soft, wet shale, which contains little manganese. The removal of nodules from the low-grade shale is a simple mechanical problem; the question is primarily to determine the lowest-cost method of separation. This report purposes to present data acquired by experimenting with samples of the ore, which form a basis for suggesting methods of concentrating manganese nodules.

Jan 1, 1942

By F. D. DeVaney

The low-grade deposits of manganese ores along the Missouri River near Chamberlain, S. Dak., are known to contain one of the largest reserves of manganese in the United States. Manganese occurs as concretionary nodules ranging in size from 13 inches in their longest dimension to particles finer than 65-mesh. The nodules are embedded in soft, wet shale, which contains little manganese. The removal of nodules from the low-grade shale is a simple mechanical -problem; the question is primarily to determine the lowest-cost method of separation. This report purposes to present data acquired by experimenting with samples of the ore, which form a basis for suggesting methods of concentrating manganese nodules.

Jan 1, 1942

By W. W. Adams

"During the calendar year 1925 the Bureau of Mines received from the operators of several hundred mines and quarries complete accident records covering deaths, permanent disabilities, and “lost time” temporary injuries. Some of the companies, - those that participated in the National Safety Competition-also furnished information showing the number of man-hours of work performed during the year. With these two types of information it was possible to calculate the accident-frequency and accident-severity rates of the different plants. Complete and comparable reports of accidents and Man-hours of “exposure” were received from 34 underground metal mines, 59 underground coal mines, 15 underground mines producing other nonmetallic minerals, and 102 open quarries or open-pit mines. The figures in the table appended to this report show the accident severity rates and other data for each of the 34 underground metal mines and for the group as a whole. It is proposed to publish similar figures for the other classes of mines and quarries at an early date.The 34 metal mines listed in the table are situated in Arizona, Idaho, Kansas, Michigan, Minnesota, Missouri, New Jersey, New Mexico, Oklahoma, South Dakota., and Utah; they employed 5, 925 men, an average of 174 men per mine, including employees above-ground as well as underground. With but few exceptions, 50 men was the minimum number of employees in any mine. The total period of employment or “exposure” at the 34 mines was 14,612,607 man-hours, an average of 2,466 hours per man, or the equivalent of 308 work-days of eight hours for each employee. Accidents resulted in 15 fatalities, 9 permanent disabilities, and 1,950 temporary “lost time” injuries (causing disability exceeding remainder of shift). The fatal and nonfatal injuries represented 132,575 days of disability. Thus the accident frequency rate for the group was 135 accidents per million hours and the accident severity rate was 9.073 days lost per thousand hours of 1 “exposure”. The severity rates ranged from 0.227 to 88.653, while the ·range of the accident-frequency rates was from 16. 6 to 307 .4. In compiling the accident severity rates shown in the table, all accidents caused by explosives were weighted at twice the number of days actually lost, as one of the purposes of the National Safety Competition was to stress the prevention of accidents caused by explosives."

Sep 1, 1926

By Meliton M. Garcia

The volume of gases produced in major and trace amounts following the detonation of two water gel and two emulsion explosives in a mine were determined. The volume .of the major gases (CO, CO2, NO, and NO2) was measured immediately following detonation, during the mucking operation, and following the removal of the muck. Tests to identify and quantify the gases produced in trace amounts were performed following the detonation only. The volume of each major gas per pound of explosive (ft /lb) ;ranged as follows: CO, 0.0424-0.3231; CO , 0.6819-1.5632; NO, 0.0129-0.1320; and NO2, 0.0019-0.1111.. An approximate average of 95% of the gases produced was found in the test chamber immediately following the detonation, while less that 2% was found in the chamber following removal of the muck. Benzene was the most significant compound found to occur in trace amounts. Scaling tests performed with a water gel and an emulsion explosive suggest that the volume of the gases per unit mass of explosive detonated diminishes as the amount of explosive per blast increases.

Jan 1, 1986

By Earl T. Hayes, W. M. Sternberg, F. P. Williams

"INTRODUCTION The limited domestic demands for lithium salts and metal before the war were met readily by the use of minerals particularly lepidolite (lithium mica) and amblygonite (a lithium phosphate), from which lithium can be recovered relatively easily. New wartime uses, however, created such a demand that it became necessary to turn to spodumene (a lithium feldspar) as the principal source of supply. Although very large deposits of spodumene occur in South Dakota and in North Carolina, it much more difficult to extract lithium from spodumene than from lepidolite or amblygonite.During the spring and summer of 1942 a study was made in Salt Lake City laboratory of the Bureau of Mines on the recovery of lithium from spodumede. Preliminary tests were made on two processes - roasting with potassium sulfate 4/ 5/ and roasting with calcium chloride and calcium carbonate 6/ -,which appeared to be the most promising of the various processes that had been proposed. By roasting spodumene with approximately its own weight of potassium sulfate at 1,050º C. and leaching the product with water, about 70 percent of the lithium could be extracted. Consumption of the relatively expensive potassium sulfate, however, was high; much of the potassium was found in the insoluble leach residue, end large amounts were lost by volatilization and dusting. By roasting the spodumene with calcium chloride and calcium carbonate, nearly 90 percent of the lithium was chloridized temperatures of 850° to 1,050° C. Much of the lithium could be extracted from the calcine by leaching with water after roasting at the lower temperatures, but volatilization of lithium chloride was appreciable, amounting to 20 to 25 percent in a direct gas-fired furnace at temperatures of 800° to 850° C. At 1,000° to 1,050° C., volatilization was far from complete. Thus, it would be necessary to use both fume collection and leaching of the calcine, unless the roasting temperatures were sufficiently high to volatilize all the lithium chloride. Because of the well-known difficulties of collecting chloride fumes, it was decided to search for a better process."

Mar 1, 1946

By Henry C. Meeves

The Bureau of Mines, between 1956 and 1963, examined 18 major pegmatite districts in Arizona, Colorado, New Mexico, South Dakota, Utah, and Wyoming to evaluate their content of beryllium, a material in short domestic supply that has become increasingly important to modern industry. This examination report includes the salient statistics on the production of pegmatite minerals other than quartz and feldspar; and brief descriptions of 170 specific pegmatite deposits.

Jan 1, 1966

By Frank G. Horino

The Bureau of Mines studied the uniaxial compressive strength of model rock pillars as a function of the angle and spacing of noncohesive planes of weakness. The model pillars were prepared from NX 2-l/8-inch diameter drill core of limestone, sandstone, and granite, and the planes of weakness were diamond saw cuts ground flat and smooth. The angle of the planes of weakness, measured from the horizontal, varied from zero to 57° in approximately 15° increments. When two planes of weakness were used, the thickness-to-diameter ratio of the wafer was 1/4, 1/2, and 1, Approximately 400 model pillars were tested in uniaxial compression. The results indicate that the uniaxial compressive strength of model pillars decreases rapidly as the angle of the plane of weakness increases from 30° to 57°, and that the spacing of these planes of weakness has only a minor effect on the strength. The effect of the number of horizontal planes of weakness, with a spacing of 1/4 and 1/2 of the diameter, upon the compressive strength of model pillars was also investigated. These results indicate that as the number of planes of weakness increases the compressive strength of the pillar decreases. Normalizing the data provides useful estimates of model pillar strengths for any rock type.

Jan 1, 1968

By C. N. Schuette

"The production of silica and magnesia crucibles in the induction furnace was attempted and achieved in the laboratory of the Pacific Experiment Station of the United States Bureau of Mines. This work was undertaken at the request of other stations for laboratory crucibles of a certain specified wall thickness and capacity.The essential new parts of this work are the development of a technique for the high-frequency furnace production of silica crucibles of greater wall thickness than could be readily fabricated from commercial fused silica, and for heavy-walled magnesia. crucibles of great density and mechanical strength. A considerable bode of patent literature on the Production of fused silica ware in resistor-type furnaces was examined, but it furnished no significant help for the present problem. Similarly sintered magnesia refractories are often made for technical purposes, but for use at temperatures of 2000o C. or over, the material must be sintered at higher temperatures than can be attained by combustion firing, and the very great shrinkage encountered at these temperatures requires special methods. Small crucibles. of magnesia fused in the electric arc have been made by Tritton and Hansen,3 but the practical size of such containers is very limited.Many different methods of making crucibles in the induction furnace were tried before satisfactory results were obtained. The following description covers only the most satisfactory method, which produced crucibles of excellent quality in a reasonable time and with a moderate expenditure of power and materials."

Oct 1, 1929

By Fred D. DeVaney

Copper sulphate is a common flotation reagent for blonde ores. Metallic iron also is present in the mill circuit, and a reaction between the iron and the salt would be in accord with well-known chemistry. The abundance of metallic iron in a flotation food may be noted by even perfunctory examination. First of all the mine contributes metallic iron, then the coarse-crushing machines add their share, and finally the fine-grinding medium its portion. If the grinding is with cast-iron balls the amount of metallics is greater than when steel is used. Thus it, is that much more metallic iron is present than would be indicated by noting the ball consumption. An estimate that the total amount of metallics is twice that supplied by the balls and liners might not be far amiss. That copper sulphate plates out on iron in an acid solution is well known, but since flotation is practiced commonly in solutions where acid has not been added this reaction has not been given sufficient thought.

Jan 1, 1929

By Andrew B. Cecala

The Bureau of Mines conducted a brief laboratory study on the 10-mm diam Dorr-Oliver nylon cyclone to investigate (1) whether high wind speed (>300 ft/min), or sampler inlet orientation with respect to wind direction, can introduce errors when sampling respirable dust, and (2) whether any such errors can be reduced by using an inlet shield. Being preliminary in nature, the study was not structured to produce definitive results, but rather to discern likely trends and to indicate whether or not a more in-depth study of the problem is warranted. Photometric mass sensing measurements suggested that as the wind velocity increased, the cyclone sampling directly into the high-velocity airstream tended to oversample, relative to the cyclone sampling in a low-velocity airstream. Orientation of the sampler introduced measurable differences in sampling efficiency at higher wind velocities. A shield placed around the cyclone diminished the effects of wind velocity and sampler orientation on sampler performance. Results of this work offer sufficient evidence to substantiate the need for a more in-depth study.

Jan 1, 1983

By Susan M. Moore

According to the Mine Safety and Health Administration (MSHA) injury database, 227 knee injuries were reported in underground coal mining in 2007 [ 1]. Low-seam coal mines are those with extremely low working heights (<42?). Gallagher et. al [2] found that the average cost per knee injury in low-seam coal operations was $13,121.29. Thus, it can be estimated that the financial burden of knee injuries was nearly three million dollars in 2007. Pressure applied to the knee while kneeling and crawling is likely a risk factor. Typically, mine workers utilize kneepads to better distribute the pressures at the knee; however, their ability to reduce the stresses at the knee is unknown. The objective of this study was to determine the pressure applied to the knee during static postures used in low-seam mining while not wearing kneepads and while wearing two kneepads commonly used in the industry (one articulated and one non-articulated).

Jan 1, 2009

By Peter F. Strong, Robert L. Lagace, Alfred G. Emslie

This paper is concerned with the theoretical study of UHF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a comer. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency that propagates with the smallest loss. Our theoretical results are compared with measurements made by Collins Radio Co. This work was conducted as part of the Pittsburgh Mining and Safety Research Center&apos;s investigation of new ways to reach and extend two-way communications to the key individuals that are highly mobile within the sections and haulage ways of coal mines.

Jan 1, 1973

By Steven R. Munts

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 39,420 acres of the 60,960-acre Skedaddle Wilderness Study Area in order to evaluate its identified mineral resources. There are no known mines or mining operations in the study area. None of the prospects or claims in or within a 1 mile peripheral zone around the study area have recorded production. At least 276 recorded lode, 6 unrecorded lode, and 29 placer claims have been located in and within about 1 mile of the study area. Approximately 191 of the claims are in the study area. Four of these were current in 1985; all four are wholly or partly inside the study area. None of the study area was being explored by private industry in 1985. Metallic and nonmetallic commodities present in the study area consist of gold, mercury, perlite, basalt, pozzolan, stone, and sand and gravel. Perlite is represented by a single deposit which contains 184,000 tons of subeconomic resources in and adjacent to the study area. No other sites contained identified resources. There are no other identified nonmetallic resources in the study area. Occurrences in and near the study area contain small amounts of gold and mercury in vein-type deposits and show characteristics similar to bulk-tonnage, low-grade gold deposits. No base-metal resources were identified. The gold and mercury mineralization and perlite deposit are spatially related to a volcanic center located in the Skedaddle Mountains. Prospects in the Skedaddle Mountains may contain both precious metals and perlite resources, but additional work is required to adequately delineate these areas.

Jan 1, 1987