Search Documents

By D. C. Crowell

This publication presents the results of a laboratory investigation of displacement of gas by injection or imbibition of water into sandstone models under essentially isobaric conditions. A brief discussion of scaling requirements is included. The influence on residual gas saturation of independently varying the parameters of dimensional ratios of the porous media, rates and methods of flooding, surface tension, initial water saturation, and permeability is shown. Of these variables, increased initial water saturation and decreased surface tension reduced residual gas saturation significantly, whereas variations in flooding rate and dimensional ratios had no apparent effect. No correlation was evident between absolute permeability and residual gas saturation.

Jan 1, 1966

By Raymond M. Kacmar

This report presents the Bureau of Mines research on the hardware reliability prediction for two Bureau monitoring projects. The basic concepts of reliability predictions are introduced along with the reliability models and assumptions used for this particular evaluation. The results of the reliability predictions are for ground-fixed and naval-sheltered environments.

Jan 1, 1986

By Thomas Varley

[For a year or more, statements have appeared in the technical press, and Especially in various trade journals, indicating that valuable metals such as gold, silver, platinum, and other rare metals, have been found and also have been successfully extracted from oil shales. These reports stated tat decarbonization and special methods of chlorination treatment, leaching and subsequent Precipitation, also cyanidation followed by table concentration of the residues after cyanidation, all indicated that told ad silver and other metals could be, and were, successfully recovered. Such articles have caused much misunderstanding, and as the correctness of some re of the statements made in them were questioned by some of the technical journals and by various chemists and metallurgists, an investigation of the subject. was begun by the metallurgical division of the Bureau of Mines, in order, if possible, to determine to what extent, if any, metals of value do occur in oil shales, and if so, the feasibility of attempting their recovery by tie processes said to have been used for teat Purpose. Inasmuch as the Bureau's station at Salt Lake City is investigating the recovery of oil from oil shales, the investigation of too recovery of metals from oil shales was assigned to my direction as superintendent 'of that station. An agreement had been entered into with the owner of m extensive oil shale deposit in Wyoming whereby I would personally collect the samples' of shales for use in the investigation.]

Jan 1, 1922

By K. E. Stanfield

One of the initial projects under the oil-shale research and development phase of the Synthetic Liquid Fuels Act, Public- Law 290, 78th Congress, approved April 5, 1944, was a survey of oil shales of the United States for the selection of a site for an oil-shale demonstration plant. The oil shales were assayed by the conventional Bureau of Mines retort method proposed by Karrick and described by Guthrie in a more recent publication. From previous experience and that had in making these assays, it became evident that the assay method should be modified or replaced by a more satisfactory one. There are several outstanding objections to the Bureau of Mines oil-shale assay method: (1) the oil yields are frequently smaller than those obtained by other types of assay equipment and by commercial retorts; (2) the assayed oil yield represents only a portion of the organic matter in the shale, which under more favorable conditions, may, Jae converted, more completely into oil; (3) the retorting procedure is controlled mainly by trial-and-error methods; and (4) the assay requires approximately 6 hours for completion.

Jan 1, 1949

By C. C. Stevenson, Thomas Varley

"The art of treating ores by the chloride volatilization process is still in the experimental stage. The process has not been sufficiently developed along chemical and metallurgical lines to state definitely just what place it will occupy in the metallurgical industry. The theory upon which the process operates has received the attention of prominent metallurgists for the past twenty years, and research and experimental work has been conducted by many investigators.Much of the experimental work done has never been published, and it seems that the accumulation of such results if made known would be an important aid to the further development of the process. The object of this paper is, therefore, to bring salient features of the process to the attention of the metallurgical industry, both for the purpose of furnishing information, and receiving from interested parties any comments which the reading of this article may suggest. A bulletin covering the work done at the Intermountain experiment station of the U. S. Bureau of Mines, situated at Salt Lake City, Utah, is in course of preparation.The chloridizing roast is usually accompanied by appreciable losses due, to the volatilization of the metals as chlorides during the roast, these losses often running as high as 30 per cent, depending upon the temperature, the character of the ores and the associated gangue material. It was not until 1891 that Croasdale, (Croasdale, Stuart, Engineering and Mining Journal, Aug. 29 1903) by observing this and stack deposits from the chloridizing roast, recognized the possibility of making volatilization a major instead of a minor feature of the roast. He then made tests on a large number of tires from different, localities, the result of which showed the, general application of the process. The main difficulty, as stated, by Croasdale, was the lack of a suitable means for recovering the fume from the furnace gasesIn 1913, Cottrell (See Mining and Scientific Press, March 29, 1913; alsoTrans. American Institute of Mining Engineering, September 1918. (Additional informa-tion is available from the owners, The Research Corporation of New lark, and Western Precipitation Co., .Los Angeles, Calif.), announced his invention of the electrostatic precipitator, which solved the problem of separating the solids from the furnace gases."

May 1, 1921

By R. D. Govier

The U.S. Bureau of Mines has developed a thin-film X-ray fluorescence technique to rapidly determine Cu, Ni, Co, Fe, and Cr in super alloy leach liquors. Total analysis time per sample was less than 15 min, as opposed to several hours for traditional wet chemical methods. Precision and accuracy were checked by replicate analyses of solutions similar in composition to leach liquors, whose analyte concentrations were well known. Coefficients of variation for all elements were found to be less than 2 pet. With the exception of the results for Fe, all relative errors of estimation were also found to be less than 2 pet. Bulk liquids are not introduced into the spectrometer; thus, the potential for damage to the instrument by leakage of corrosive liquids is eliminated.

Jan 1, 1989

By Murray Jacobson

Data obtained by the Federal Bureau of Mines on the dust explosion hazard in air are presented for 220 samples of agricultural products. Information is given on ignition temperature of dust clouds and layers, minimum explosive concentration, minimum electrical energy for ignition, explosion pressure and rates of pressure rise, amount of inert dust required to prevent flame propagation, and, in a few instances, the permissible oxygen concentration in an atmosphere to prevent ignition by spark and by heated surface. The effects of particle size and source of sample on explosibility are shown. The relative ignition sensitivity, severity of explosion, and overall explosibility of the materials are characterized by empirical indexes. This report contains Ma obtained by the Bureau in laboratory studies on the explosion hazards of agricultural dusts. Recognition of the dangers will encourage adoption of adequate measures to prevent ignition and explosion during preparation, processing, and utilization of the materials. Agricultural products constitute one of the largest groups of materials used in America. More than 260 million tons of various grains, much of which now exists in dust form, was grown in 1958.6/ Over 600,000 tons of the annual production of 200

Jan 1, 1961

By John Nagy, Austin R. Cooper, Murray Jacobson

Data obtained in the Bureau's study of dust explosions of 313 elemental metals , alloys , catalysts , and ores comprising 54 types of material are summarized . Information is given on ignition temperature , spark energy for ignition , minimum explosion concentration , explosion pressure , rate of pressure rise , and in some instances , the admixed inert dust and oxygen concentration in an atmosphere required to prevent ignition of dust dispersions . The effects of particle diameter on explosibility and pyrophoricity are also discussed .

Jan 1, 1964

By R. W. Fatzinger

The accident-frequency rate for placer mining in 1942 is reported as 36.923 accidents per million man-hours worked. This figure places placer-mining accident frequency slightly higher than that given for quarrying-35.7-but considerably under the 78.0 for coal mining and 56.5 for metal mining.4 Placer mining is subdivided into four types of activity: Underground, surface, dredging, and hydraulicking. It is the purpose of this paper to present and discuss safety practices in dredging and hydraulic mining; therefore, the following considerations will be limited to these two types of placer mining.

Jan 1, 1948

By J. A. Rowland

Manganese-copper alloys containing 60 percent or more electrolytic manganese exhibit an unusual combination of high vibration damping capacity with good strength properties. Properties of the pure alloys were first studied in the laboratories of the Federal Bureau of Mines and have been described in a series of technical papers1/ published from 1941-49. The unusual characteristics of these manganese-copper alloys attracted the attention of research metallurgists and several additional investigations have also been reported in the literature.2/ The engineer, also, was attracted by the combination of high strength and high vibrational damping capacity possessed by these alloys. A wide field of application in structural and machine design was obvious. However, serious difficulties encountered in commercial fabrication of structural or machine components from the alloys retarded attempts at their practical utilization. For this reason the Federal Bureau of Mines, in cooperation with the United States Navy, Bureau of Ships, undertook a program designed to develop practical methods for fabricating a selected group of the high-damping alloys. It is the purpose of this paper to summarize a part of that investigation in a form suitable for use by the metallurgist interested in commercial fabrication of the alloys.

Jan 1, 1955

Reynolds Metals Company announced plans to increase its rate of production of primary aluminum by 17 thousand tons per year by the end of February. Other producers were expected to increase operating rates during the first quarter of 1976 (see table 10 pg. 29). CHROMIUM -Under the Trade Act of 1974, a petition was filed July 16, 1975, with the U.S. International Trade Commission (ITC) by the Tool and Stainless Steel Industry Committee for Import Relief and the United Steelworkers of America, AFL-CIO, for import relief for certain stainless and alloy tool steel products. The Commission determined on January 16, 1976, in a report to the President, that increased quantities of imports of stainless steel sheet and strip, plate, bar, and rod and alloy tool steel except ingots, blooms, billets, slabs, and sheet bars were a substantial cause of serious injury or threat thereof. The Commission recommended import quotas for the period 1976 through 1980. The President has 2 months in which to act, with his decision subject to a Congressional override.

Jan 1, 1976

By John Nagy

Dust explosion data obtained in laboratory tests by the Bureau of Mines are presented for 181 miscellaneous materials that present an explosion hazard. Data are given also for 50 dusts that present primarily a fire hazard and for 88 dusts that did not present an explosion hazard.

Jan 1, 1968

By C. P. Fang, V. A. Marple, K. L. Rubow, P. H. McMurry

"It has been known for some time that sizes of aqueous particles may be affected by flow-induced relative humidity (RH) changes. The RH of air flowing through an impactor decreases as a result of pressure drop through the impactor and increases because of aerodynamic cooling within the high-speed jets, as illustrated in Figure 1. Because the sizes of aqueous particles depend on RH, the impaction stage on which such particles are collected may be different from the stage where they ought to be col¬lected, based on the particle size at the sampler inlet.Fuchs (1980) reviewed literature on water vapor condensation in impactors. The reviewed impactors operated at jet velocities of 100-250 m/s. Particle size increases ow¬ing to water vapor condensation were found in all cases. In one case (Khorguani et al., 1970), it was found that very small droplets (Dp <_ 0.02 um) containing sodium chloride and silver iodide were collected in an impactor with a cut point of 0.32 µm and a jet velocity of 100 m/s. Fuchs believed that such particles could not be captured in an impactor without having been enlarged by condensation. Winkler (1974) sampled at¬mospheric dust with a rectangular nozzle impactor that had a nozzle cross section of 0.3 x 15 mm, a cut size of 0.4 um, and an average jet velocity of 100 m/s. No adhesive was used on the impaction plate. The collection efficiency increased as air humidity was increased from 20% to 100%. The effect was especially noticeable in the increased collection efficiency for hygroscopic particles, and was attributed to condensation.Extensive theoretical and experimental research work on the distortion of the particle size distributions in impactors was done by Biswas and coworkers (1985, 1987). The impactors employed in the study were a low-pressure impactor with high jet velocity stages (Hering et al., 1978, 1979) and a conventional six-stage impactor, Sierra's model 226, operated in the incompressible regime. Ammonium sulfate aerosols were chosen for the study. In the low-pressure impactor, an orifice operating at a Mach number of 1 causes a sudden pressure drop, significantly reducing the RH in the next two stages (stages 5 and 6). This results in a 0.15-um diameter ammonium sulfate droplet shrinking to about 0.07 um at stage 5 when the inlet RH is 95%. In stage 7, the tempera¬ture drop is considerable because the jet speed is sonic. For an inlet RH of 95%, a 0.03 um droplet grows to about 0.06 um. However, the same size droplet at an inlet RH of 25% grows to only 0.04 um. For the Sierra model 226 cascade impactor that is operated with a Mach number of 0.27 at the last stage (stage VI), it was found that for an inlet RH of about 67%, particle growth would occur in stage VI. At 80% RH, both stages V and VI were affected. Biswas et al. (1987) stated that Mach number alone does not determine the size biasing; the type of aerosol, the inlet conditions, the temperature and pressure ratio, and the impactor geometry (throat length, jet-to-plate distance, etc.) must be considered for each stage in evaluating the distortion of the particle size distribution."

Mar 1, 1992

By J. D. Noll

The Mine Safety and Health Administration (MSHA) has promulgated rules to limit the exposure of metal/nonmetal underground miners to diesel particulate matter (DPM). These rules have resulted in many types of control tech­nologies being implemented including diesel particulate filters (DPF). The passive type DPF is the most desirable because it requires little maintenance and it regenerates while the vehicle is operating. One problem with passive DPFs is that many vehicles cannot develop the sustained exhaust temperatures needed to initiate DPF regeneration, and thus it is required that the DPF be catalyzed to decrease the temperature needed for regeneration. In some past studies, such catalyzed filters have been shown to cause an increase in the nitrogen dioxide concentrations in the exhaust, resulting in a potential health hazard. In this study, a lightly catalyzed DPF along with a fuel-born catalyst were employed to help reduce the DPM emissions from a 980F loader used for cleanup in a stone mine. After 30 days of use, the filter continued to regenerate successfully at the exhaust temperatures generated by this loader, substantially reduced DPM concentrations emitted in the exhaust, and did not cause a measurable increase in nitrogen dioxide levels that could be attributed to the device.

Jan 1, 2009

By E. L. Litchfield

Descriptions are given of the techniques and apparatus used by the Bureau of Mines for determinations of flat plate ignition quenching distance and minimum spark ignition energy. The descriptions include discussions of reaction vessel materials, shapes, and sizes and discussions of electrode configurations. Spherical, hemispherical, or flat plate electrodes are recommended. The preferred metal in electrodes and electrode supports is stainless steel; the flat plate electrodes incorporate flanges of low electrical conductivity which are most frequently formed from glass. Various aspects of the electrical energy supply system are discussed and suitable arrangements of components are indicated. The concept of a thermal relaxation time is introduced as a basis for the choice of a minimum interspark time during the testing of a gas mixture. The following indicate the varied conditions under which these tech were utilized: Mixture pressures between 10 mm Hg and 45 psig, initial temperatures between -78° and +198° C, and gaseous mixtures representing wide ranges of cL.. D reactivity and corrosiveness. Minimum ignition energies were determined which varied from about 10-7 joule to nearly 103 joule.

Jan 1, 1967

By E. G. Davis

The Bureau of Mines made laboratory-scale experiments to examine the technical possibilities of reclaiming manganese from slags produced by oxygen lancing of high-manganese pig iron. Ferromanganese was added to molten pig iron to yield a 4-to 5-percent manganese hot metal, which simulated a product obtainable from the blast furnace. This was injected with oxygen to reduce the metal to 1 percent or less manganese and form a slag containing about 40 percent manganese. The molten slag was water-quenched, treated with H2SO4) roasted at 660° C, and water-leached to give soluble manganese and iron sulfates. The sulfates were precipitated as hydroxides, converted to the oxide form, and smelted to produce a standard ferromanganese containing 74.6 percent Mn and 0.01 percent P. As an alternate method of manganese recovery, a manganese cell feed was prepared from the leach solutions and electrolytic manganese was produced. Direct smelting of the high-manganese slag resulted in 74.2 ferromanganese meeting ASTM specifications except for phosphorus content. The high phosphorus content of the metal and high slag-to-metal ratio obtained made this approach unattractive.

Jan 1, 1966

By C. H. Kats, E. G. Meiter, J. J. Bloomfield

"INTRODUCTION.Street manholes for underground power and signal circuits, and for sewers vary in size from small openings that a workman can enter, to large central vaults. As the gas hazards in manholes are similar to those in mines, the mine safety committee of the Bureau of Mines was asked whether the miners' flame safety lamp is a practicable device for indicating inflammable gases in manholes.The coal miner detects firedamp (methane or CH4) with his flame safety lamp by observing the luminous can or the increased length of flame that appears when 1.5 per cent or more of the combustible gas is present. The lamp flame also warns him of lack of oxygen by going out when the oxygen becomes less than 16 to L7 per cent. A tentative rule regarding the proposed use of safety lamps at manholes has been suggested previously as follows: ""Testing for gas: Do not enter manholes until you have .assured yourself that the manholes are free from dangerous gases, by testing with an approved safety lamp, by ventilation, or by other adequate methods."" The Bureau's committee recommended that miners' flame safety lamps are not suitable,testing in manholes because hydrogen gas may be formed therein. The flame safety lamps approved by the Bureau of Mines for use in aseous mines are safe in presence of methane and while not tested against the members of the paraffin hydrocarbon series (CnH2n+2) higher than methane they been have been used therein; the lamps should not be used in hydrogen or acetylene they can initiate explosions in presence of these gases."

Oct 1, 1925

By R. R. Allen

Gieseler plastometer tests were performed on eight western coking coals at retort - immersion depths ranging from 2 to 3-3 /4 inches (measured to the center of the coal charge ) . Increased maximum fluidities were associated with greater retort - immersion depths , the most pronounced increases being observed on highly swelling coals when tested at 3-3 /4 inches . The maximum fluidity of one of these coals when tested at 3-3 /4 inches was 146 percent greater than that observed at 24 inches . Retort - immersion depth had no significant effect on the temperatures of initial softening , fusion , maximum fluidity , end of fusion , and solidification .

Jan 1, 1964

By L. C. IlsLey

Through the cooperation of the Pennsylvania Department of Mines the writer obtained from State, records detailed information concerning coal-mine accidents occurring in Pennsylvania bituminous mines during 1939, particularly those nonfatal accidents in which the injured person lost 60 or more days? time from mark. The writer wishes to acknowledge assistance received from Pennsylvania State officials, especially Richard Maize, secretary of mines, and. Joseph J, Walsh, deputy secretary of mines; also to Thomas Dickinson,3/ of the Bureau of Mines, who rendered valuable assistance in assembling the data an the several tables.

Jan 1, 1941

By John P. Harmon

Vehicles traveling on untreated dirt and gravel roads at open-pit mines disseminate high concentrations of dust (fig. 1). Excessive dust creates safety hazards by reducing visibility and may endanger the health of the men who breathe it. If the dust contains free silica, it can cause silicosis. In addition, maintenance costs of mechanical equipment are increased if equipment is operated in extremely dusty places. Dust on haulage roads in hot, arid country can be controlled if the surface of the road is sprinkled frequently and adequately with water. Often, when roads are sprinkled with water to control the dust, hazards are caused through reduced traction and skidding because of the mud that is formed on the surface of the road. Reducing the amount of water used will help to reduce the hazard of skidding.

Jan 1, 1957