Search Documents

By R. K. Koch

The Bureau of Mines developed a zircon sand molding process for static casting of small titanium or zirconium shapes. Castings with unfinished weights up to 3.5 kg (7.7 lb) were produced in an inductoslag furnace and castings up to 7 kg (15.4 lb) were poured in a consumable electrode skull-casting furnace. Molds and cores were made by ram-molding, foundry-grade zircon sand (AFS gfn 93 to 95) bonded by grade D waterglass and tempered with water. Molds and cores were cured either at 250° C (482° F) or 900° C (1,652° F). Castings from the higher temperature molds broke cleanly from the sand while the lower temperature molds produced castings that had to be cleaned by sand-blasting. However, low-temperature cured molds and cores have a number of advantages as follows: (1) A faster, less energy-consuming curing cycle is used; (2) expended cores are water soluble which greatly facilitates core removal; and (3) enough of the binder in crushed expended molds is reactivated by temper water so that the molding mix can be reused five times without any fresh binder additions and up to twenty times without exceeding a total cumulative binder addition of 52 ml/kg dry sand. Crushed used molds that had been cured at 900° C had no detectable binding strength when mixed only with temper water. A large number of oxide and silicate mold washes were studied for improved casting integrity. The most effective wash found for zirconium or titanium casting was monoclinic zirconia (325 mesh).

Jan 1, 1977

By R. W. Watson

A belt-wearable self-contained self-rescuer (SCSR) manufactured by the CSE Corp. and designated the "SR-1OO" was evaluated for safety in the underground mine environment by the U.S. Bureau of Mines. The evaluation consisted of laboratory tests on the chemicals contained in the unit and field trials to simulate the mine environment. This report summarizes the test results and compares the results with those from earlier tests with chemical and compressed oxygen self-rescuers. It was concluded that the new SCSR did not pose any different or more severe hazards than the earlier units. In view of the mine-proven safety record of the SCSR's now in service, no reason could be found to disallow use of the belt-wearable unit.

Jan 1, 1991

The influence of fuel additives on automobile exhaust emissions was studied using engines currently found in the U.S. vehicle population. The fuel additives used in the experiment were four multifunctional additives and one lead antiknock additive. Experimental work was done to determine both the direct effect of the additive per se on exhaust emissions and the influence of Long-term additive effects on emissions with mileage accumulation. Results showed no significant direct or intermediate effect on exhaust emissions for any additives tested. In subsequent experimental work concerned with the long-term or indirect effects of additives, the detergent-dispersant additives were found to have little influence on emissions when used in conjunction with high-quality oil and motor fuel. The lead (tetraethyl) antiknock additive increased exhaust hydrocarbons approximately 12 to 17 percent during a 4,000-mile accumulation period using a base fuel containing 2 ml of tetraethyl lead per gallon. An unleaded fuel was used during a similar accumulation period with no significant increase in exhaust hydrocarbons with mileage.

Jan 1, 1971

By W. K. Overbey

Surface fracture trace density, changes in roof rock type, and topographic unloading due to drainage were mapped for the mining areas located in the Blacksville-Osage, W. Va., quadrangles to investigate their influence on mine roof falls. Using these factors, a technique was developed to predict probable roof fall areas ahead of projected mining operations. As a feasibility test of this proposed technique, areas were delineated where one, two, and all three of these factors were operating to formulate a "potential hazard map" for comparison with roof fall observations that were made. The limited evidence suggests that in combination these factors are reliable predictors of where roof falls are likely to occur. This technique promises to be a useful tool in planning mining operations.

Jan 1, 1973

By Henry E. Blake

The Bureau of Mines has been engaged in a continuing research effort to develop processes for increasing the recovery and utilization of fluorine from low-grade resources. This current research has shown that over 98 percent of the fluorine in phosphate rock is extracted when the ore is treated with excess phosphoric acid in the presence of water vapor at 150° to 180° C. More than 80 percent of the fluorine can be recovered as fluosilicic acid, which can then be converted to commercially useful hydrogen fluoride or fluorspar by previously developed Bureau processes. Extraction of P205 from the ore was about 98 percent in batch tests and 90 percent in semicyclic tests.

Jan 1, 1974

By Robert H. Merrill

This report summarizes the first phase of studies to determine the design and behavior of an unsupported roof in an experimental room in limestone. The selection of a roof horizon and the design of the room were results of an investigation of the geology of the formation, the physical properties of samples from the proposed roof, and calculations from the theory of gravity-loaded beams. The design of the opening, some physical properties of the roof in place, and the behavior of the roof were checked by tests in a full-scale experimental room. The room was instrumented to measure roof deflection, separations in the roof strata, and incipient failure. The dimensions of the room before instrumentation was installed were 10 by 100 feet; the room was widened in successive increments to 40 by 100 feet. Between widening operations periods up to 6 months were allowed to provide a time test of the roof spans. The results of the measurements of deflection and separations showed that the lowest 6-inch layer in the roof became detached as the room was widened. This layer was eventually removed after standing without failure for about 4 months at room dimensions of 40 by 100 feet.

Jan 1, 1957

By V. A. Danielson

The Bureau of Mines studied waste disposal methods a1 a coal mine in Kentucky and another in Alabama to develop cost estimates, to provide better knowledge of current practices, and to guide consideration of alternate disposal methods. Costs of the existing waste disposal systems at each mine were estimated using present-day costs of equipment and labor. Costs of waste disposal systems using alternate equipment were also estimated. Although total disposal costs were essentially the same for both operations, reclamation costs will differ because of different reclamation practices.

Jan 1, 1969

Continuous remote sensing of air speed In underground mine airways. Approach An ultrasonic technique measures a form of air turbulence which is proportional to air velocity. How It Works The stainless-steel enclosed transducer consists of a sensing head with circuitry, and a telemetry card. The sensor uses a patented ultrasonic technique to measure a form of turbulence created In the air. This turbulence, known as vortex shedding, is related to the air speed through the sensor. Air flowing past a cylindrical post creates vortices which flow down the air stream on both sides of the post. Pulses from an ultrasonic transmitter pass through the vortices to a receiver; the effect of the vortices on the pulses is a measure of air velocity. The transducer contains a telemetry card, known as an accessor, which transmits reports on air velocity through a pair of wires to a monitoring system. The accessor contains an analog-to-digital converter and digital telemetry circuitry required for computer system operation. The transducer does not contain any read-outs or alarms and air velocities are displayed by means of a centrally located

Jan 1, 1982

By R. T. Johansen

The adverse effects on waterflooding and well-completion methods of clay minerals indigenous to petroleum-production formations recently have received considerable attention. Knowledge of the types and amounts of clay minerals present would allow estimates of the response of such formations to injected or infiltrated water; however, the random distribution of clays in sedimentary formations makes direct evaluation of ?water sensitivity? desirable. A method for the direct evaluation of water sensitivity has been developed, based on measurement of water-vapor adsorption. Correlation of such data with the results of nitrogen-adsorption measurements provides valuable information on the content and properties of clay minerals in sedimentary rocks. The method is relatively simple and has the advantage that it may be used with small, irregularly shaped chips or shale-streaked samples, as well as with typical core samples. Methods previously employed required separating the clay from the rest of the reservoir-sample material and then performing a clay analysis either by X-ray diffraction, differential thermal analysis, liquid permeability, or a combination of these methods (2,3) .3/ This water-vapor-adsorption method requires measuring only a few points on the isotherm to tell whether or not the sample is water sensitive. The goal of these measurements is not to determine the type or amount of clay present, but what will be its sensitivity to flood water. This method gives a direct means of solving this problem.

Jan 1, 1958

By Michael J. Sapko, Eric S. Weiss, Kenneth L. Cashdollar

A fundamental safety research area for the National Institute for Occupational Safety and Health (NIOSH) is to eliminate the occurrence of coal mine explosions or to mitigate their effects. One approach is to develop and evaluate new and innovative seal designs that provide increased explosion protection for mining personnel. The NIOSH Pittsburgh Research Laboratory (PRL) cooperated with HeiTech Corp. of Virginia, Barclay Mowlem Construction Ltd. of Queensland, Australia, and the Mine Safety and Health Administration (MSHA) in three separate research programs to evaluate the strength characteristics and air leakage resistance of numerous innovative seal designs and ventilation control structures for use in underground coal mines. For each phase of the program, various full-scale seals, stoppings, and an overcast design were constructed in PRL's Lake Lynn Experimental Mine near Fairchance, Fayette County, PA. The seals and stoppings were built in crosscuts and were subjected to explosions to evaluate their strengths. Four pumpable cementitious seal designs ranging in thickness from 610 to 915 mm (24 to 36 in) were evaluated in the first cost-reimbursable research program with HeiTech Corp. A simple wooden framework with brattice liner was used as a form to contain the cementitious slurry during the curing period. As the seal designs decreased in thickness, higher compressive strength cementitious grout was used. All four seals withstood an explosion pressure pulse of at least 138 kPa (20 psi) while maintaining acceptable air leakage resistance. In the second cost-reimbursable research program with Barclay Mowlem Construction Ltd. of Australia, several innovative seal and stopping designs and an overcast design were evaluated. Each of the seal designs and the overcast side and wing walls used one or more air-inflated vinyl bladder assemblies anchored to the mine roof and hitched into the ribs and floor. The air within these bladders was displaced with a high-strength cementitious grout. The overcast deck consisted of a 200-mm ('7.8-in) thick reinforced cementitious slab. This was the first time that an overcast structure had been explosion tested under full-scale conditions. All of the seals, stoppings, and overcast design passed the air leakage tests before being subjected to a series of explosions with static pressure pulses ranging from 14 to 475 kPa (2 tab 69 psi). Instrumentation measured seal and overcast wall displacement as a function of time. The 450-mm (1 7.7-in) thick seal in the 2.8-m(9-ft) high third crosscut withstood an explosion pressure of 170 kPa (25 psi), but failed during a later test, which generated a peak static pressure of 475 kPa (69 psi) at the seal location. A similar 450-mm-thick seal in the 2.1-m (7-ft) high second crosscut withstood three explosion tests, which generated peak static pressures of 195, 205, and 370 kPa (28, 30, and 54 psi) at the seal location. Next, the overcast design withstood four explosions, which generated static overpressures ranging from 16 to 47 kPa (2.3 to 6.8 psi). A third program at the request of MSHA evaluated the effectiveness of using pressurized grout bags (Packsetter bags) along the mine roof and ribs in lieu of floor and rib hitching for a standard-type solid- concrete-block seal. This program was initiated to address an urlusual geological mining condition encountered when building seals in entries where required rib hitching is not a viable option due to soft friable coal. Results showed that the use of these quick-setting grout-filled Packsetter bags pressurized internally to 300 kPa (44 psi) not only provides a seal that can withstand a 138-kPa static pressure explosion, but also provides a sealing option where rib hitching is not possible.

Jan 1, 2003

By L. M. Adams

Experiments in reclaiming acidic surface-mined coal lands with raw fly ash from bituminous-coal-fired powerplants were conducted by the Bureau of Mines at two sites in northern West Virginia. Plots at both sites were treated with varying tonnages of fly ash from three area powerplants and were planted with a variety of grasses, legumes, trees, and shrubs. Eight grasses and seven legumes were investigated. Greatest promise for growth under harsh soil conditions was shown by Kentucky 31 fescue, rye and red top grasses, and birdsfoot trefoil, a legume. Survival of trees and shrubs was negligible. Addition of fly ash to the spoil increased the pH to a range tolerable to some types of plant growth, improved the texture of the soil, and increased the available water of the resulting mixture.

Jan 1, 1971

By S. P. Sandoval

Previous research by the U.S. Bureau of Mines demonstrated that nonionic surfactants increased the leaching rate of copper in the flask leaching of chalcopyrite with ferric sulfate if sufficient ferric sulfate was present. This research was continued by the Bureau in Part 2 to further explore the application of nonionic surfactants to the dump leaching of chalcopyrite. A polyoxyethylene lauryl ether was selected as the superior nonionic surfactant tested at 25° and 50° C. The addition of the surfactant increased copper leaching by 116 pct at 25° C and 1.0 pct solids and by 61 pct at 50° C and 0.5 pct solids at Fe 3+ concentrations greater than 1 g/L. At 0.1.0 g/L Fe 3+ and below, the addition of the surfactant produced as much as a 35 pct decrease in leaching. Each of the nonionic surfactants studied was found to be heavily adsorbed by a typical chalcopyrite ore, which poses a serious barrier to the application of nonionic surfactants in an actual chalcopyrite dump.

Jan 1, 2010

By Lung Cheng

The Bureau of Mines conducted laboratory tests to investigate the ease of frictional ingition with frozen (nonrotating) conical bits cutting into sandstone. The number of strikes with a new bit to obtain ignition of a combustible methane-air environment was measured. Tests were made with bits tipped with both tungsten carbide and steel at several bit attack angles (angle between bit axis and sandstone surface) and initial tip angles (included angle at the tip of the new bit). Carbide-tipped bits required more strikes for ingition than steel-tipped bits, by a factor of 7 to 10. With a carbide-tipped bit, the number of strikes for ingition increased by a factor of about 3 if the bit attack angle increased by 10° or if the initial tip angle decreased by 10°. During use, abrasive wear of the frozen bit caused a flat surface to form at the tip of the bit, thereby decreasing the tip angle. As the attack angle increased, however, the new bit involved a smaller wear-flat area whereby, abrasive wear was decreased.

Jan 1, 1987

By M. E. Tyrrell

Magnesia spinel (MgO.Al203) recovered from dusting slags in the system MgO.Al203-2Ca0.SiO2 is in the form of single crystals most of which will pass 35-mash. This investigation was undertaken by the Bureau of Mines to evaluate the concentrates as a refractory raw material. Three specific types of refractory bricks were studied: (1) dense, (2) lightweight bubble, and (3) insulating. Test specimens ware fabricated 1 by dry pressing, fired to 1,675° C., and tested by procedures common to the industry. The concentrates produced a refractor, having satisfactory density and mechanical strength; however, spinal is sensitive to thermal shock and the possibility of producing a spall-resistant brick using aggregate of such small grain-size must be considered remote. Lightweight refractorias fabricated of spinel bubbles were the most promising of the types tested. They were 30 percent lighter in sight than the dense refractory, their mechanical strength was good, and definite superiority in thermal shock resistance was indicated.

Jan 1, 1962

By L. A. Haas

The U.S. Department of the Interior, Bureau of Mines, is conducting laboratory-scale research to determine the leaching conditions required with sulfuric acid for extracting base metal from a matte with a copper-to-nicke1 ratio of 6 to 1. The matte (61.2 pct Cu, 9.7 pct Ni, 3.3 pct Fe, 21 pct S, and about 5 oz of precious metals per ton) was prepared from Duluth Complex (Minnesota) ore by smelting a bulk sulfide flotation concentrate. The matte was pre leached at atmospheric pressure to selectively extract 20 pct of the nickel, and the undissolved solids were referred to as the matte residue. Autoclave leaching of the matte residue extracted over 95 pct of the nickel, copper, and iron. The remaining leach residue in the autoclave contained over 100 oz of precious metals per ton. The leaching conditions required were matte grind of greater than 98 pct minus 325 mesh, pulp concentration of 50 g/1, total pressure of 100 psig with oxygen at 150° C or 400 psig with air at 180° C, 50 g/1 H2S04, 700 rpm agitator speed, and 6 hours of leaching time. The leaching time was decreased to 2 hours by increasing the agitator speed to 1,300 rpm. Sulfuric acid concentration greater than 50 g/1 did not appreciably enhance the base metal extraction, but with less acid, residues with higher iron concentrations were obtained. Supersaturation of the liquor was prevented at 150° C by using a 1ixiviant that contained 30 g/l Ni and 20 g/1 Cu.

Jan 1, 1979

By Edward L. McHugh

The study area, which comprises 11,500 acres, includes the 9,610-acre Whitewater Wilderness Study Area, in the California Desert Conservation Area, 15 miles northwest of Palm Springs, CA. The U.S. Bureau of Mines evaluation of mineral resources is based on examination of prospects and mineralized areas during the spring of 1981. The Whitewater study area is mainly underlain by granodiorite to quartz diorite and their gneissic equivalents in an igneous-metamorphic complex. Late Tertiary sedimentary and volcanic rocks locally overlie the crystalline complex in the eastern part of the study area. The study area lies between branches of the San Andreas fault system.

Jan 1, 1986

By Peter Krause

This report provides an overview of the worldwide photographic industry and of the applications of photography. It also covers important technological and market trends, with special emphasis on those factors which may affect the consumption of silver in the future. The text is divided into the following eight sections: 1. Principal manufacturers of silver-based photographic products 2. Major product sectors 3. Structure of the international market for silver-based photographic products 4. Silver-bearing raw materials for the manufacture of photographic products 5. Processing of photographic products: recovery of silver and recycling 6. Methods for estimating the use of silver in photographic products 7. Basic function of silver in photography and alternate image capture and recording systems 8. Brief history of photography Silver- based photographic materials are made for many applications that require different photochemical and physical response characteristics and a wide variety of formats and sizes. All of these products are laminates consisting of a surface-treated support and bonded gelatin layers. Two basic types predominate - films and papers. Films have transparent or translucent plastic supports (mostly cellulose tri-acetate and polyester), while papers have mostly a paper core coated with polyethylene resin layers on both sides (RC type). The front layer contains white titanium dioxide to provide high reflectivity and the back layer a matting agent. However, a few so-called fiber base papers are still supplied. These have a high quality paper base coated with a baryta layer ; i.e. a gelatin layer containing white barium sulfate. The manufacture of photographic film and paper supports requires special procedures and equipment, because of the severe requirements for chemical purity, optical integrity and uniformity (see Table 1 on page 10 for a list of the principal makers of film and paper supports).

Jan 1, 1992

By L. B. Berger

Studies showing the effect of mixing hot exhaust gases with the intake air of a four-stroke-cycle Diesel engine are described. The results indicate a marked increase in carbon monoxide in tip exhaust gases, a decrease in oxides of nitrogen, and no significant effect on aldehydes. The increase in carbon monoxide was greater at higher fuel-air ratios and was caused partly by the increase in fuel-air ratio end partly by the decrease in oxygen concentration resulting when exhaust has was added. The application of these results to the use of Diesel engines underground is considered.

Jan 1, 1940

By G. R. Palmer

The Bureau of mines evaluated the elution of uranyl carbonate from a strong base resin with a mixed carbonate eluant in a fluidized system. The system consisted of a multiple-compartment ion-exchange (MCIX) elution column with a continuous flow of solution, except for short periods when the resin increments were withdrawn. The exchange of uranyl carbonate from the mill-loaded strong base resin with an eluant composed of 1.0 [M] NaaCOs plus 1.0 [M] NH4HCO3 was studied. The effects of solution flow rate, aqueous-to-resin flow ratio, column diameter, compartment height, initial resin concentration, and column length were examined. The experimental data indicate that for the eluant examined, a resin residence time of 240 minutes is necessary to attain 90-percent elution efficiency. Also provided is a technique for sizing an elution MCIX column form pilot plant experimental data.

Jan 1, 1979

By Oliver C. Ralston, Foster Fraas

"INTRODUCTION The predominant characteristic of powdered mica is the thin -plate shape of the particulars, and the thinner the plates, the more enhanced is this characteristic. Consequently, it is frequently desirable to grade mica according to the thickness of the plates. Concerning the various possible methods for grading mica, very little has been published. There is also no information on the relative quantities of mica per given range of plate thickness. This paper presents a graphical method that shows how these quantities are distributed and how the different methods of grading compare.CUMULATIVE BULK DENSITYBulk density, which is an indirect measure of the plate thickness, was determined in a small cylindrical cup of 3.37 cubic centimeters volume. The mica was placed in the cup under a standard procedure. The densities thus measured checked these determined in a 273 cubic centi¬meter cup with less than a 2 percent error.In calculating cumulative densities it is important to know how they are averaged. In any grading operation the bulk density of a series of fractions is determined. Starting with the lowest density fraction, the cumulative percent under-density can be calculated through the various fractions. It is possible that quantity may be measured by volume or weight and that the averaging may be done by a number of methods. However, experimentally it has been shown that the quantity must be by volume and that the averaging must be arithmetic. This is illustrated in table 1, in which the calculated and actual bulk densities are listed."

Sep 1, 1942