Search Documents

By Jon C. Volkwein

In This Chapter [Instruments for measuring dust How to calculate the amount of dust from a source How to get a valid concentration measurement Sampling to assess control technology effectiveness] When there is more than one source of dust, sampling may be required to find which dust sources are most significant. Then, efforts to reduce dust can be concentrated where they will have the most impact. This chapter explains how to perform dust source sampling. It describes two kinds of instruments that are available and discusses their limitations. It explains how environmental variables such as concentration gradients, dust dilution, and production changes can impact dust measurements. It also suggests practical ways to improve the validity of dust source measurements under adverse conditions, such as high-velocity airflow or the presence of water mist in the air. [Dust source sampling at coal mine longwalls and at tunnels is more complicated. Chapters 3 and 7 have more information on sampling in those circumstances.] TWO KINDS OF INSTRUMENTS FOR MEASURING DUST Gravimetric samplers. The conventional gravimetric sampler is a good device for measuring dust because it is the instrument used for compliance measurements. This dust sampler consists of an air pump, a small cyclone that separates out the respirable size fraction of the dust cloud, and a filter to collect the respirable dust. In coal mines, the Mine Safety and Health Administration (MSHA)-approved gravimetric sampler uses a 10-mm Dorr-Oliver cyclone operating at an airflow of 2.0 L/min [30 CFR78 74 (2002)]. A correction factor of 1.38 is applied to make the results consistent with the U.K. MRE sampler, the instrument on which the 2.0 mg/m3 coal dust standard is based.

Jan 6, 2003

By O. C. Blade

Studies on more efficient utilization of petroleum have been made for 50 years by the Bureau of Mines. As part of this work, the Bureau has analyzed thousands of samples of crude oil by its standardized routine method, and many of these analyses have been published, sometimes in special compilations, other times in connection with reports of research on petroleum. This report is a finding index for all analyses published from 1921 to 1959, and brings up to date the information in Information Circular 7470 3 and in the appendix of Bulletin 490.4 The routine method of analysis and the equipment originally were described in a report by Dean and associates. 5 This report has long been out of print, but Bulletin 490, bringing the procedure and its modifications to date, was published in 1951. 6 Briefly, the procedure consists of testing, by standard methods, small samples of a crude oil for gravity, sulfur, color, viscosity, pour point, and (more recently) nitrogen; and, by a standardized procedure, distilling a portion of the crude oil and determining certain properties on the separated fractions and residuum. Careful records are made during the procedure, and the distillation data obtained are used to compute the approximate amounts of products present in the sample--such as percentages of gasoline, kerosine, gas oil, and lubricants. The principal data and results are recorded on a standard analytical report form. An analysis of a sample of crude oil from a recently developed field is shown in table 1. Compilations of these analyses, sometimes in tabular form and usually for specific geographic areas, are published from time to time. Analyses often are included in connection with other studies, such as engineering field reports.

Jan 1, 1959

By R. Barany

The heats of formation of anhydrous ferric sulfate and anhydrous indium sulfate were determined by solution calorimetry. At 298.15° K the heats of formation from the metal, rhombic sulfur, and oxygen were -615.6 ±O.7 kcal/mole for ferric sulfate and -649.6 ±O.6 kcal/mole for indium sulfate. Heats of decomposition at 298.15° K are given for the reaction that forms metal oxide, sulfur dioxide, and oxygen) and for the reaction that forms the metal oxide and sulfur trioxide.

Jan 1, 1965

By R. O. Dannenberg

The Bureau of Mines investigations described in this report were undertaken to devise a process to economically recover precious metals and copper from low-grade, complex electronic scrap generated in large quantities by military and civilian electronic operations. Leaching with various media is applicable to certain selected items of electronic scrap but cannot be practically applied to complex mixtures of scrap. A process comprising incineration, caustic leaching to remove aluminum, smelting with a siliceous slag, and electrolysis recovered 99.9-percent-pure copper metal and anode slimes assaying more than 7,000 ounces per ton of combined precious metals. Silver, gold, and copper recoveries were 93, 95, and 87 percent, respectively. Cost analysis indicated that an alternative process using direct smelting of the scrap to make assayable products for sale to a custom smelter would provide better overall financial returns.

Jan 1, 1972

In response to increased aluminum demand, U.S. producers have begun reactivating primary aluminum capacity which was shutdown during the 1974-1975 recession. Reynolds Metals Company started up almost 80,000 tons per year of idled capacity at Listerhill, Alabama, and Jones Mills and Arkadelphia, Arkansas plants. Howmet Aluminum Corporation and Alumax announced that the operating rate at their jointly owned facility at Frederick, Maryland was being increased from 75 percent to 100 percent, equivalent to a 44,000 ton-per-year increase in output. Kaiser Aluminum and Chemical Corp. expected to restart one of the two idled potlines at its Mead, Washington facility in May raising its production rate by 27,000 tons per year. ANTHRACITE - The anthracite market for the larger sizes continues at a good level, and although the demand for industrial sizes has been weak, the current trend indicates an increased demand for industrial fines by the steel, auto, and other industries.

Jan 1, 1976

By A. F. Colombo

The differences in starch demands that occur between ore types subjected to the anionic flotation of calcium-activated gangue and the range of residual starch contents expected to give the best metallurgical response were evaluated on a batch and pilot plant basis. A phenol-sulfuric acid procedure was used to determine the residual starch contents in the iron ore slurries. Three pilot plant campaigns on samples from a group of orebodies located on the Marquette Range, Michigan, showed that in the rougher flotation pulp, a residual carbohydrate range of 25 to 100 ppm, which is equivalent to a 0.5 lb/short ton spread, yielded optimum results. Concentrates assaying at least 65 percent Fe and less than 6.0 percent Si02 and containing more than 80 per-cent of the recoverable iron were obtained. Both batch and continuous research indicated that starch adsorption is calcium modulated and relatively unaffected by the fatty acid additions employed. Residual starch level is not a critical control factor, but the addition must be adjusted to about 25 to 50 ppm residual starch and kept in this range for most effective utilization of the added tapioca flour.

Jan 1, 1972

By R. V. Ramani, K. V. K. Prasad, M. Swaminathan

"Engineering design involves, in addition to numerical calculations, considerable amount of expertise and judgement. The expertise and judgement is required to conceptualize and idealize the problem, select a suitable mathematical model for the problem and to interpret the model results in terms of stipulated design constraints. In recent years, knowledge based systems (KBS) have provided the capability to integrate the qualitative experiential and expert knowledge with ~he quantitative knowledge for improved analysis and design of systems. A possible KBS architecture for mine ventilation system design was discussed by Ramani and Prasad · (1987). The expert system (ES) component of the KBS supports the analysis and interpretation phases of the ventilation design process with an algorithmic program used for the solution of alternate designs. The purpose of this paper is to discuss the data and knowledge needs for developing such a system and a formal means of their representation on the computer. A number of ES shells were evaluated to explore possible development and delivery environments for the system. A brief summary of this evaluation is also provided.INTRODUCTIONLuxbacher and Ramani (1979) have discussed the design process of mine ventilation systems and have provided the interrelationships that exist between ventilation, strata control, drainage and material handling systems and mining methods. They have also outlined the importance of correct analysis of the problem, choice of the right solution method and a rigorous interpretation of the solutions. The expertise required for analysis and interpretation phases was identified as the key element in developing effective and efficient ventilation system designs. Such expertise is embedded in the right choice of questions to be asked of the user as well as in directing the user to a wide array of alternative methods that may satisfy the design requirements. With advances in artificial intelligence applications in recent years, particularly expert systems, the integration of expertise into traditional mine planning and design algorithms has been facilitated. These planning and design aids, employing the integration of numeric and symbolic logic and called coupled systems, are powerful tools for engineers to tap the benefits of experts (Kitzmiller and Kowalik, 1985; Fenves, 1985). The purpose of this paper is to discuss the means of representing knowledge for the design of mine ventilation systems through the use of a coupled system. The KBS is visualized as consisting of the following components:"

Jan 1, 1989

By Robert L. Lappi

This report covers the final phase of a project demonstrating the economic efficiency of cross-ridge mountaintop coal mining. A demonstration mine was established at Big Wheel Gap in northeastern Tennessee. Not only was cross-ridge mining feasible for the selected site, but parallel cut methods could not be used due to a deficit in available spoil storage. Cross-ridge mining permitted coal extraction at a cost almost identical with costs simulated by computer projections using mathematical optimization techniques. No unexpected environmental problems were encountered. Volume I is accompanied by Volume II which describes the MATHMINE Mine Simulation System, software used to support the mining demonstration.

Jan 1, 1984

By W. G. Hopkins

The development of systems for location of miners who have become entrapped following a mine disaster has been one of the major research goals in the Bureau of Mines. This study details the preliminary development of such a system. Current technologies for locating trapped miners from the surface are either simple direction finders or time difference pulse systems that have accuracy limitations. Developing technologies using full vector field measurements at several receiving points are currently being studied. The necessity of measuring field strength with great accuracy can be a drawback in these systems. A system that operates with continuous wave radio signals, whose phase differences can be measured accurately even in weak signal conditions, greatly improves the location accuracy. A microcomputer would be used in conjunction with the system, to gather and manipulate the data to automatically pinpoint the location of the trapped miner. Comparison of this system with existing technology indicates a favorable accuracy/complexity ratio for the phase difference of arrival technique.

Jan 1, 2011

By A. J. Kraemer

This paper on the physical and chemical properties of crude oils from California fields is one of a series of reports on the on the districts of the United States. The paper includes a short discussion of results, tabular data, and individual analyses of eight. California crudes. Analyses of other crude oils from California have been published it Reports of Investigations 2595, 2608, and 2846. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting 65 samples was facilitated by the courtesy of representatives of oil companies in California. The methods used in testing and analyzing the samples are described in detail in Bureau of Mines Bulletin 207. A discussion of the interpretation of crude-oil analyses, as made by the Bureau of Mines, is given in Bureau of Mines Report of Investigations 2806.

Jan 1, 1931

By Thomas M. Barczak

This US. Bureau of Mines report examines the roof and floor contact pressure provided by the interaction of a shield with the surrounding strata. Controlled forces were applied to an 800-ton two-leg shield in the Bureau's mine roof simulator; the distribution of forces acting on the canopy and base of the shield were measured with 24 hydraulic pressure cells. Several influential factors that affect the load distribution were investigated: (1) the magnitude of loading (leg pressure); (2) the profile of the canopy, principally the upward-sloping tip; (3) the base-lifting device; (4) horizontal load acting on the shield; and (5) compliancy of the immediate roof and floor. It was concluded that the shield does not develop full canopy or base contact without deformation of the strata. Maximum contact pressures are developed at the rear of the canopy and on the toes of the base. Less than 10 pct of the available shield capacity is developed at the canopy tip despite the design intention to ensure tip contact. Horizontal loading reduced the toe pressure acting on the base by as much as 75 pct. The base-lifting device exaggerated the inherently high toe loading, increasing the contact pressure by more than 200 pct.

Jan 1, 2010

By Alex C. Smith, Thomas A. Gray, Lynn M. Crayne, Michael A. Trevits, Phil Glogowski

Mine fires constitute one of the greatest threats to the health and safety of those working in the underground environment and each event has the potential for disastrous consequences. Of the major mine fires and thermal events that have occurred in the United States in the last 6 years, it is estimated that remotely installed seals could have been used in 63% of the events to control fire growth or to aid in fire suppression work. The National Institute for Occupational Safety and Health (NIOSH) is conducting full-scale tests at the NIOSH Lake Lynn Experimental Mine to evaluate and improve remote mine seal construction technology. The main focus of this work is to develop reliable technology that will completely close the mine opening from floor-to-roof and rib-to-rib. This paper presents the results of remote seal installations using grout-based materials.

By Ralph H. Espach

The value of careful fractionation in the manufacture of petroleum products is recognized more and more by petroleum refiners. Recent studies have shown that the quality of the products depends largely on the type of fractionating equipment and on the care used in operating the equipment. For example Rue3 has shown that careful fractionation of pressure distillate will greatly reduce the amount of chemical treatment necessary to produce finished gasoline. The advantages of the combination of pipe still and bubble tower in obtaining good fractionation are well recognized in the petroleum industry. However, the equipment designed in the past has in general been much too large for convenient laboratory use. The present paper describes a continuous-distillation apparatus for the laboratory study of fractionation. This apparatus has given very satisfactory results in the study of different crude oils and petroleum products. A discussion of the theory and action of bubble towers has not been given, as this subject has been discussed previously by Cooke and Rue4. It is believed that the distillation curves of the products obtained from this apparatus show clearly its capabilities.

Jan 1, 1928

By C. W. Davis

This paper is the second of a series of progress reports on a study, of the hydrometallurgy of manganese which is being conducted in an endeavor to make possible utilization of the large deposits of low-grade domestic manganese ores that occur in several States. There are at least four processes in which a knowledge of the action of SO2 gas on manganese oxides at elevated temperatures may prove of value. One ,of these involves dissolution of manganese from ores. The Bureau of Mines has investigated the hydrometallurgy of manganese by a process in which SO2 gas, a waste product at many smelters, is passed into water to form a solvent for manganese. Although Several manganese minerals acre readily dissolved, rhodochrosite (MnCO3) was attacked but superficially.§. Recent experiments have shown that a roast at 650 to 900°C converts the manganese of rhodochrosite to a form that is quickly dissolved by a weak SO2 solution. Introduction of smelter gases containing as much as 5 per cent SO2 during such a roast would not add much to the cost of the operation and might result in the formation of considerable water-soluble manganese sulphate.

Jan 1, 1930

By W. K. Collins

Engineered scavenger compounds (ESC's) developed by the U.S. Bureau of Mines are a novel class of compounds that selectively can recover a desired element from a solid or molten alloy. Lithium titanate (L2Ti307 or Li2O?3Ti02) is used as an ESC to recover lithium (Li) from aluminum-lithium (Al-Li) alloys. X-ray diffraction measurements have shown that Li2Ti307 undergoes a phase change during scavenging from an orthorhombic structure to a hexagonal structure. This change is due to the incorporation of lithium in the matrix of the material and the effect of temperature. Although both phases are metastable, the hexagonal phase that forms during the scavenging of lithium from Al-Li alloys appears to be the more stable phase. Recovering lithium from the ESC by electrodeposition does not cause the structure to revert to the orthorhombic phase. The orthorhombic and the hexagonal structures of Li2Ti307 have similar scavenging capacities for lithium. This report proposes a new mechanism for the phase transformation.

Jan 1, 2010

By B. W. Gandrud

At the Southern Experiment Station of the Federal Bureau of Mines, reports are prepared from time to time on results of washability studies of commercially important coal beds in the Southern Appalachian region. The investigations that provide the material for these reports are made by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and the mine operators. This report records the results obtained on a sample of run-of-mine coal taken in June 1953 from the Pratt bed at the Davidson Coal Co. mine about 1 mile west of Graysville, Ala. One of the main objectives of a washability study is to obtain technically and commercially important data in connection with the best methods for preparing and utilizing the Nation's limited reserves of good coking coal. Such information is important from the standpoint of conservation in that it facilitates selection of preparation methods that will yield an acceptable grade of coking coal with a mini-mum of losses of coal in the rejects. The Pratt bed is one of the main sources of coking coal in the Jefferson County part of the Warrior field. This is the first time, however, that data from a complete washability study of coal have been obtained from this bed in Jefferson County. In the Graysville area, Pratt-bed coal has good coking characteristics and is used for blending with other coals in making metallurgical coal. The extent of its use in such blends is severely limited in this area, however, by the fact that it has a high sulfur content, which has not been reducible to any great extent by washery treatment.

Jan 1, 1955

By R. A. Guidotti

The Federal Bureau of Mines studied the thermal decomposition of the nitrides of the Group V A metals (CbN, Ta3N5, and VN) with the goal of preparing high-purity metals. Solid-state purification and arc and electron-beam melting were examined. Electron-beam melting proved to be the most efficient means of nitrogen and oxygen removal. Columbium and tantalum of 99.9-pct purity were prepared by this technique; in the case of vanadium, however, nitrogen could not be reduced below the solid-solution level.

Jan 1, 1976

By D. H. Baker

These investigations were conducted to determine the feasibility of molten salt electrorefining of zirconium scrap, offgrade sponge, and alloys under contract number AT(11-1)-475 between the Atomic Energy Commission and the Federal Bureau of Mines. Offgrade zirconium sponge having a Brinell hardness of 169 can be refined by this technique to produce metal having, consistently, a Brinell hardness of less than 90. Also, zirconium alloy scrap, approximating zircaloy-2 in composition, can be refined to recover zirconium metal with a Brinell hardness of less than 100 that is essentially free of the major alloying elements. Analysis showed that the quantities of these elements were decreased as follows: iron from 0.27 to 0.002, tin from 1.36 to 0.001, nickel from 0.02 to 0.001, and chromium from 0.12 to 0.002 percent.

Jan 1, 1961

By John E. Pahlman

The Bureau of Mines investigated the feasibility of removing heavy metals from mineral-process waste streams by precipitation with lignochemicals and humic acids. Lignochemicals are by products from the paper industry, while humic acids are obtained by caustic treatment of peat, subbituminous coal, and lignite. These high-molecular-weight organic materials have many functional groups, which can coordinate and form innercomplex salts with heavy metals that are crystalline precipitates. Filtering of a humic-acid-or lignochemical-treated solution or waste stream containing these precipitates removes the heavy metal sequstrates. Tests were conducted with two lignochemical samples, three humic acid samples, lime (CaO), and sodium hydroxide (NaOH) in which increasing amounts of these additives were reacted with 50 mL of solution containing Fe3+ , Al3+, Cr3+, Pb2+, Cu2+, Cd2+, Zn2+, Co2+, Ni2+, Mn2+, and Hg1+. At the appropriate pH, greater than 90-and 99-pct removal was achieved for these 11 heavy metal ions from the 10-and lOO-ppm solutions, respectively, using lignochemicals and humic acids. Removal efficienC)' with these organic materials is better than that with CaO, especially for the more toxic ions, Hg1+, Cd2+, and Pb2+. Unlike the precipitates formed with NaOH or CaO, those with lignochemicals and humic acids are compact and noncolloidal. The volume of their sludge is sharply lower than that of the finely dispersed lime or soda precipitates; thus, their removal in settling tanks or by simple filtration is enhanced.

Jan 1, 1988

By C. H. Gorski

Evaluation of raw materials for mineral wool is one phase of the Bureau of Mines broad program for the more effective utilization: of our mineral resources. The experimental work and test-evaluation results on several raw materials as useful components for the production of mineral wool are presented in this report. Samples from all sections of the United States, including copper slag from Tacoma, Wash., pebble phosphate slime from Florida, and granites from Massachusetts and Minnesota, have been blown into mineral wool successfully in the laboratory tests. Maximum conservation of the Nation's mineral and manpower resources requires maximum utility of those resources. Al though the domestic reserves of oil, gas, and coal are tremendous, judicious use of these fuels through the use of proper insulation will insure the highest thermal efficiency. The effectiveness of mineral wool as a heat-insulating material has assumed an increasingly important role in the national economy, and it has become a fuel saver in countless applications. The most immediate concern to many is the use of mineral wool in the home, which promotes uniform temperature and minimizes drafts by reducing heat transfer through the walls, ceiling, and floors. There are, however, many industrial and commercial uses that require large volumes of mineral wool each year.

Jan 1, 1951