Search Documents

By G. St. J. Perrott, N. A. Tolch

"The measured strength of an explosive depends to a certain extent on which it is determined. An earlier investigation showed the relative propulsive strength of dynamites as determined in one type of apparatus, ballistic pendulum.4 The aim of this paper is to precept strength data on these same dynamites determined in another type of apparatus, the Trauzl lead block, and to compare the results with those of the ballistic pendulum. Trauzl lead block have been in use many years for the determination of thy strength of explosives, under moderate confinement.5 The common practice is to shoot 10 grams of explosive, in tinfoil wrapper,- and then to measure the volume of the cavity produced by the shot. The volume of the original borehole is deducted from the gross expansion and sometimes a correction is made for the expansion produced by the detonator. Dry sand is used for stemming the charge.It has been found that the expansion in Trauzl blocks is not strictly proportional to the charge. Naoum5 believed that for scientific accuracy the charge should undoubtedly be regulated to give the same average expansion for each sample tested, but for expansions of 200 to 400 cubic, centimeters the deviation from proportionality is not sufficient to give results appreciably in error.Neubner7 found that the proportionality curve is tangent to the charge-expansion curve at about 300 cubic centimeters expansion, provided that no deductions are made for the volume of the original borehole or the effect of the detonator; the total or gross expansion is proportional to the charge between expansions of 250 to 350 cubic centimeters without serious error."

Oct 1, 1930

By W. E. Young, D. T. Delicate

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat- room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Nov 1, 1963

By David C. Scott

Between 1990 and 1991, the Bureau of Mines studied the mineral resources of the Kaibab National Forest to appraise the resources present and to determine the types of deposits, and their location. The study included a comprehensive literature search and a limited amount of field investigation of minerals and mining activity in and near the Forest. Small amounts of copper with lesser amounts of gold and silver have been produced from limestone-hosted, strata-bound deposits in the North Kaibab and Tusayan Ranger Districts. In addition to these small metallic deposits, volcanic cinders, pumice, flagstone, and sand and gravel have been quarried in the Chalendar and Williams Ranger Districts. At least ten uranium-mineralized breccia pipes have been identified in the Tusayan Ranger District, One of these, the Canyon pipe, contains a high-grade uranium ore body with associated silver, copper, lead, vanadium, and zinc. The mine permit for the Canyon pipe has been approved and the mine shaft head frame erected.

Jan 1, 1992

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and. the results are described in this report.

Jan 1, 1983

By Robert F. Randolph

Introduction This paper is a descriptive analysis of injuries and fatalities at small surface bituminous coalmining companies in Pennsylvania. The purpose of analyzing a specific industry sector and location is to identify issues that might be missed in a wider analysis. Other studies of small mine safety (e.g., Peters and Fotta, 1994, Randolph and Boldt, 1997) have shown that the relationship between safety and mine size is not a simple one. Some injury types occur at higher rates at small mines, while others occur at lower rates. Consequently, an analysis limited to a specific type of mining can help identify hazards and issues specific to that sector. The results of this analysis will be useful for directing training, intervention, and research efforts towards the most prevalent causal factors and incident types. Procedures and Definitions Data sources The primary sources of data for this analysis were files provided by MSHA containing information collected under Title 30 Code of Federal Regulations, Part 50. These files, commonly referred to as “Part 50 data”, are provided though MSHA’s Program Evaluation and Information Resources directorate. Two primary types of injuries were selected from the Part 50data: Fatalities (MSHA “degree of injury” code 1) and lost-time injuries, otherwise known as nonfatal with days lost (MSHA “degree of injury” codes 2 through 5). Lost-time injuries involve either actual days away from work or days of restricted activity or both. Fatality and lost-time injury incidence rates were calculated using the standard MSHA formula: Number of injuries per 200,000 employee-hours. Additional information on company sizes and mine ownership was provided by the Pennsylvania State University College of Earth and Mineral Sciences. Time span A five-year time span was selected for this study. More than a single year of safety experience is usually needed to capture a broad range of incident types. Many types of injuries, especially fatal injuries, can be extremely rare, and may be missed if too short a time span is selected. However, a time span that extends too far back may begin to suffer historical threats to validity. That is, incidents that occurred several years ago may be caused by hazards that have since been remedied or may be related to mining practices and conditions that no longer exist. A five-year span offers a practical compromise between these two concerns. Consequently, the MSHA Part 50 data files from 1993 through 1997 were used. The 1997 file was in “preliminary” form at the time of the study, so small variations from the final 1997 “close out” file can be expected. Based on past experience, we do not expect the close-out variations to have a significant impact on the findings.

By J. W. Miller

Wyoming County had for many years supplied large quantities of coking coals to coke plants throughout the eastern United States and Canada. Up to the present most of the coal has been produced from relatively few beds, but in the future the coal will be produced from beds not previously mined in quantity. This trend is shown in the entire Winding Gulf field, of which Wyoming County is a part. This publication is one of a series of Bureau of mines reports appraising the Nation's coking coal, which y be used to determine the practicability of upgrading marginal deposits to metallurgical standards. This investigation of the preparation characteristics of Wyoming County coals is the third of the series undertaken in West Virginia.

Jan 1, 1955

Safety rules for installing and using electrical equipment in and about coal mines covered in this information circular supersede those previously included in Bureau of Mines Bulletin 514, issued in 1952. This revision brings these rules up to data and more nearly in line with present operating and safety practices in the industry. The, rules are intended to supplement existing existing Federal and State regulations, and no provision shall be construed to oppose or supersede any provisions of the Federal Mine Safety Codes, the Federal Coal Mine Safety Act, or the mining laws of any State. The rules were designed to permit progress, such as application of new or improved materials and equipment or use of new practices where these materials, equipment or practices retain or improve the level of safety established by these requirements. It is hoped that they will fill the need for a concise edition for mine electricians and electrical engineers, especially those who do not have ready access to more detailed rules or codes.

Jan 1, 1964

By W. D. Dietzman

In view of the developments and recent interest in recovering heavy oil, this report was prepared to present general information on more than 2,000 heavy oil reservoirs in more than 1,500 fields in 26 states. Information given on each heavy-oil deposit includes the following items: Field and formation, location, average or range of depth, average API gravity of oil, aver- age thickness of formation, areal extent of field, total productive wells drilled in field, discovery date of field, field status in 1963, cumulative production to Jan. 1, 1964, and all known types of secondary-recovery operations initiated (active and terminated) in the reservoirs. The geographical location of heavy oil accumulations in the United States is shown by a map, and a brief discussion of 14 different areas is given in the text. As of Jan. 1, 1964, 75 percent of the heavy oil reservoirs in the United States had produced more than 10 billion barrels of oil and are estimated to contain over 90 billion barrels of oil in place. It is also estimated that if the deposits which have had little or no production history, such as the one in Missouri, were included, the total remaining heavy oil in place would be in excess of 150 billion barrels. To find economical ways of recovering this vast reserve of heavy oil, industry is developing technology in several types of thermal-recovery methods. Some of the general considerations and more suitable limitations in selecting a prospect to study fur thermal-recovery techniques are: Lithology, depth, viscosity of reservoir fluids, gravity of oil, reservoir thickness, oil in place, and permeability and porosity.

Jan 1, 1965

By Serge Rudchenko

A study to determine the potential use of retaining structures in open pit backfilling. Research and review of the open pit mine environment, mine waste disposal, and past and current use of retaining structures. A development of specific structures, the culvert/ tunnel concept, and an anchor block retaining concept. The cost benefit of retaining structures used for in-pit backfilled waste.

Jan 1, 1981

By Ren G. Dong, Thomas W. McDowell, John Z. Wu, Chris Warren, Dan E. Welcome, Chun L. Dong

Hand forces are important factors for risk assessment of hand-arm vibration syndrome (HAVS).1 Grip force is one of the most important force components in the operation of powered hand tools. A considerable number of studies on grip force have been reported. It is well known that the grip force applied on a cylindrical handle is not uniformly distributed on each axis across the center of the handle cross-section.2 Therefore, maximum and minimum orientations of grip force exist around the handle. Such orientations have not been clearly identified. In a recently proposed international standard (ISO/CD 15230, 2005),3 it is stated that “the direction of the main gripping force is generally parallel to the z-axis defined in ISO 8727.” 4 This assertion is questionable, and further examinations are required. The objective of this study was to establish a fundamental theory on the distribution of the grip force around cylindrical handles. Methods As shown in Fig. 1, the grip force is defined as a vector composed of normal and shear components (FN & FT) in this study. Fig. 2 shows the hand coordinate system defined in this study, together with the ISO systems.1,4 Based on this novel grip force definition, we derived four fundamental properties and a theorem. More significantly, we formulated a novel hypothesis: similar to Mohr’s circle of stress, the normal and shear components can be represented approximately using an ellipse on the plane of the two force coordinates, as shown in Fig. 3. The maximum and minimum grip normal forces are termed as the first principal grip force (F1) and the second principal grip normal force (F2), respectively. Their corresponding orientations are termed as the first principal grip angle (a1) and the second principal grip angle (a2). A series of experiments were conducted to test this hypothesis. Twelve

Jan 6, 2006

By Chas. F. Jackson

The work of the mining division is divided between seven sections, each in charge of a supervising engineer, as follows: 1. Metal-mining methods section, the supervising engineer of which is also supervising engineer of the Southwest Experiment Station at Tucson, Ariz. 2. Metal-mining research section. 3. Nonmetal minim section. 4. Coal-mining section. 5. Mine-ventilation section. 6. Mineral-industries survey section. 7. Electrical section. The names of the sections indicate broadly the fields covered by each, and in the following pages the objectives and type of work of each section will be summarized briefly and the active problems listed. The work done during the calendar year 1936 will also be summarized.

Jan 1, 1937

By Frank L. Wideman

This information circular describes methods used in mining inclined beds of phosphate rock in mines operated by San Francisco Chemical Co. in Rich County, Utah. The mines are on the western flank of the Crawford Mountains, a short, narrow range in northern Utah near the Idaho-Wyoming corner (fig. 1). The western front of the range is a conspicuous wall of folded and faulted sedimentary rocks that rises abruptly 300 to 600 feet above the floor of the adjacent Bear River Valley. Rex Peak, highest point in the range, is approximately 8,000 feet above sea level. The area surrounding the mines is sparsely populated. Randolph, the county seat of Rich County, has a population of 650. It is 10 miles southwest of the mines by road and the only town in their vicinity.

Jan 1, 1958

By Roy C. Bartholomae, Jeffrey Shawn Peterson

1. INTRODUCTION In the early 1980s, the U.S. Department of the Interior’s Bureau of Mines Pittsburgh Research Center required that a large reverberation acoustic facility be constructed. This facility was designed to determine the sound power level emissions of mining equipment, especially continuous miners and jumbo drills. A contract for a conceptual design of a reverberation chamber was awarded to Wyle Laboratories of Huntsville, AL, which had extensive experience in the design, construction, and accreditation of acoustical reverberation chambers. The following standards were referenced as guidelines for the design of the chamber: ANSI S1.31-1980, “Precision Methods for the Determination of Sound Power Levels of Broadband Noise Sources in Reverberation Rooms” and ANSI S1.32-1980: “Precision Methods for the Determination of Sound Power Levels of Discrete-Frequency and Narrowband Noise Sources in Reverberation Rooms.” Specific requested criteria included that the room be large enough to accommodate typically large mining equipment and that there be adequate acoustical modal density in the frequency range of interest. It was also required that the room dimensions would support broadband acoustical measurements down to the 100 Hz third octave band. With the closing of the Bureau of Mines in 1996, this reverberation chamber lay dormant for a number of years. However, this facility is now part of the National Institute for Occupational Safety and Health’s (NIOSH’s) Pittsburgh Research Laboratory (PRL). One of NIOSH’s missions is to decrease noise induced hearing loss among the nation’s mineworkers. To this end, PRL researchers are refurbishing and instrumenting this reverberation chamber to facilitate assessment of the various engineering controls being developed to decrease the sound power level emissions of mining equipment. Early on, this work has sought to bring the chamber up to the level of ISO 3743-21 standard for engineering grade measurements for broad-band noise, with a longer range goal of improving the lab to meet the requirements of ISO 37412standard for broadband precision grade measurements. 2. DESIGN OF THE REVERBERATION CHAMBER The nominal room dimensions are 18.3 meters long by 10.3 meters wide with a height of 6.7 meters. The chamber volume is 1,286 cubic meters. These dimensions are important, as few reverberation facilities are large enough to test typically huge mining equipment. The floor is poured concrete with a sealer to make it acoustically reflective. The walls are built of hollow concrete block, 16 inches long x 8 inches high by 12inches thick. Each block has two hollow cores. The hollow block cores were completely filled with concrete with horizontal and vertical steel reinforcing bars 16 inches on center. This was done to supply a

By R. I. C. Manning

The Old Dominion Co, at Globe, Ariz., like the: Phelps Dodge Corporation with which it is closely allied, considers safety a major operating problem. Safety is fostered by this company in consideration of both the humanitarian and economic aspects; the officials, take pride in promoting the welfare of employees, and the management has found that the safest way is the most eco¬nomical and that unless an organization is operated economically it can not continue to exist successfully. In planning and operating any safety, organization, terry things must be taken into consideration because an Enterprise can not be operated solely for safety any more than it can for any other single part of the operations. All work must be planned and executed for the common interest.

Jan 1, 1931

PRODUCTION of cesium, cesium salts, and rubidium salts in the United States declined somewhat from 1961 levels; rubidium production was virtually unchanged. Imports of pollucite declined because consumption was supplied partially out of inventory. Domestic Production.-About 50 tons of pollucite was reported mined at the Tin Mountain mine in the Black Hills of South Dakota. The Dow Chemical Co., Midland, Mich., MSA Research Corp., Callery, Pa., and Penn Rare Metals, Inc., Revere, Pa., produced a total of 159 pounds of cesium. Rubidium production remained essentially the same as in 1961. Shipments of the two metals by these companies and by American Potash & Chemical Corp., Trona, Calif., totaled 279 pounds. Production of cesium and rubidium salts by American Potash & Chemical Corp., Penn Rare Metals, Inc., and Rocky Mountain Research, Inc., Denver, Colo., declined substantially during 1962.

Jan 1, 1963

By G. Richards Gwinn

Vermiculites are secondary minerals formed by the: alteration of biotite and philogopite mica and are associated with basic rocks such as dunites, serpentines, and pyroxenites. Vermiculite was first described by T. H. Webb in 1824. It remained a mineralogical curiosity until 1913, when the first commercial deposit was discovered in the Turrett mining district of Colorado. Expanded or exfoliated vermiculite was first marketed in 1915 from a deposit in this district 5 miles southeast of Hecla, Colo. This activity was brief, but successful and continuous commercial development began in 1921 in Montana. 'Deposits in other States have been found and developed, but Montana is by far the largest producer. Vermiculite has also been found in South Africa, Western

Jan 1, 1944

By Charles G. Maier

"INTRODUCTION The use of thermodynamic calculations to answer practical problems in metallurgy, especially those that are relatively difficult to test experimentally, is rapidly becoming a conventional method of procedure. Nevertheless, these methods cannot he applied effectively until the fundamental thermodynamic constants used for them have become available either by direct experiment or by recalculation of data already existing in more or less undigested form.In an attempt to collect such data far the compounds of lead and the antimony group the incentive has been to make a preliminary survey that will disclose the gaps or questionable phases of available information and to collect data that may be used to answer certain rather practical problems presented by operating metallurgists.This report comprises three sections; the first gives the basis of selection of the constants which may now be given or estimated, and the later sections discuss the application of the figures obtained to two of the more interesting problems.The reader will discover that many of the quantities involve critical study of a number of more or less discordant observations. Although certain data could be rejected on the basis of thermodynamic comparisons, it must not be overlooked that many of the figures are the results of rational estimates rather than exact experiment. The use of thermodynamic methods to control and partly authenticate such estimates is one of its most valuable characteristics for the practising metallurgist or chemist, who cannot check by direct experiment each property of the materials which he converts to usable form.Nevertheless, while it is definitely possible in certain instances that the final figure selected for the heat or free energy of a process or substance may be in error by as much as a few hundred to a few thousand calories per formula weight, questionable figures are usually revealed by the thermodynamic calculations made. When quantities of such degree of accuracy are, and they often must be, used for estimating an unknown reaction, the result often gives no more than the order of magnitude of the desired quantities. Yet even in these extreme cases the answer is far more reliable and valuable than an unordered guess or a conclusion based on incorrect data."

Dec 1, 1934

By Doss H. White

In 1989, Alabama's nonfuel mineral industry produced a State record of $463 million of nonfuel mineral commodities, an increase of $4 million over that reported by the State's mineral producers in 1988. The new record marked the fourth consecutive year in which mineral production increased over that of the previous year. Alabama ranked 22d among the States in total mineral value. Cement, stone, and sand and gravel were the three leading mineral commodities produced, accounting for 77% of Alabama's total mineral value. During the year, there were several acquisitions by Alabama cement and stone companies, and the only tantalum mine in the United States completed its first full year of operation.

Jan 1, 1991

By S. A. Bortz

This report presents the results of an extensive laboratory testing program to determine the physical properties of shotcrete including the use of fast-set agents, controlled set cements, and both wet and dry shotcreting equipment. Shotcrete was placed under simulated field conditions using the dry and wet processes. Mechanical properties obtained for accelerated and nonaccelerated shotcretes include compressive, flexural, and shear strength, elastic modulus and Poisson's ratio, and shear and tensile properties of shotcrete bonded to coal, sandstone, and shale. Physical properties measured were unit weight and permeability to methane gas. The data show that rapid setting shotcrete has the potential for improved coal mine ground control. There is no clear evidence that either wet or dry process shotcrete is superior to the other; however, indications are that regulated set cement is preferred to cement containing fast-setting admixtures.

Jan 1, 1973

By Benjamin W. Haynes

The Bureau of Mines conducted research to provide technical information needed to devise waste management plans for the processing of manganese nodules. Studies included summary descriptions of Pacific manganese nodules, process options and flowsheets, methods for characterizing nodules and their tailings, and results of analyses of laboratory and pilot-plant generated tailings. This information is the result of a cooperative research effort of the Bureau of Mines and the National Oceanic and Atmospheric Administration (NOAA), with NOAA providing funding and the Bureau conducting the research. A summary of the extensive literature review is provided for manganese nodule mineralogy, chemistry, processing techniques, and methods of analyses. Characterizations and analyses of laboratory-generated tailings and slags are given, as well as the results of the leaching studies on these waste materials. Leachability was determined by three standard leachate tests- the Environmental Protection Agency (EPA) extraction procedure (EP) toxicity test, the American Society for Testing and Materials shake extraction test, and the U.S. Army Corps of Engineers-EPA seawater elutriant test. While the wastes generated in the laboratory may not be entirely representative of those to be generated in full-scale plants, results of these studies provide a positive indication that commercial recovery of cobalt, copper, manganese, and nickel from manganese nodules would be environmentally acceptable.

Jan 1, 1985