Search Documents

By Hanns J. Billmayer

Optimized Operator Compartment layouts based on previous Bureau of Mines activities in standardization and optimization of controls were designed and installed in three operating vehicles. Two National Mine Service 48A-36 TorKars were modified in production prior to delivery to the Quarto Mining Company. An Elkhorn AR-4 scoop owned by Adanac Coal Company was modified in a local rebuild shop. The modified vehicles were then evaluated underground under normal production conditions for a 60 day period. Vehicle operators and management appear well satisfied with the compartment modifications.

Jan 1, 1976

By P. J. G. du Toit

Coal has been mined by hydraulic means in various countries, i.e., the hydraulic excavation as well as the hydraulic transportation of coal has been practiced. The hydraulic breaking (excavating) of the coal dealt with in this report is done with a monitor directing a continuous jet of water against the coal, pressures of the water fed to the monitor range from 1500 to 2500 psi at 1000 to 2100 gallons per minute Transportation of the coal from the face is by fluming if a gradient exists in excess of 2 or, when a favorable gradient does not exist, the coal is pumped from the face by various types of pumps which can also provide a means of hoisting the coal to a higher elevation as required. This report presents: 1.) preliminary design and systems specifications of a demonstration miner (referred to in this report as a hydrominer), 2.) mining configurations showing good promise for typical U.S. thick coal seams in three seam pitch categories, (0° - 7° = Flat, 8° - 250 = Moderately pitching, 26° - 90° = Steeply pitching), along with cost and performance analyses for each system, 3.) a definition of a test program that will provide sufficient engineering data for the design of a water jet cutting head adequate to cut coal in those typical U.S. thick coal seams The cost analysis data showed hydraulic methods to be economically competitive with present thick seam raining methods. It was also obvious from studies of thick seam methods that the hydromonitor coal breaking techniques are more effective in removing most of the coal with its long reach of 60 ft. (or more), is a safer mining system, and produces very low coal-dust content in the air (usually less than 0.25 to 0.5 mg/cubic meter). It is recommended that the USBM sponsor a full fledged continuation of the hydraulic mining program: (a) lab, test, (b) preliminary field test, (c) full scale mine section demonstration.

Jan 1, 1977

By Arno C. Fieldner, Howard I. Smith, J. W. Paul, SAMUEL SANFORD.

Many mine samples of coal are analyzed each year in the laboratories of the Bureau of Mines. The analyses are made in connection with investigations relating to fuels belonging to or for the use of the United States Government, the causes of accidents in coal mines, the geologic relations of coal beds, and the character and the value of the coal and lignite in the public lands. The systematic collection and analysis of such samples in connection with fuel investigations was begun in 1904 at the Government fuel-testing plant at the Louisiana Purchase Exposition, and was under the direction of the United States Geological Survey for six years. Descriptions of the coal samples collected between the beginning of this work, July 1,1904, and the transfer of the fuel-testing and mine-accident investigations to the Bureau of Mines, July 1, 1910, were compiled and published in Bureau of Mines Bulletin 22.a Descriptions and analyses of samples collected during the fiscal years 1911 to 1913 were published in Bureau of Mines Bulletin 85.b The present bulletin presents analyses and descriptions of samples collected during the fiscal years 1913 to 1916. In order that the material in this bulletin may be used to supplement that presented in Bulletins 22 and 85, the same plan of geographical classification has been followed, the analyses and descriptions of the samples being grouped in alphabetical order according to the State, county, and town near which the mines or prospects sampled are situated.

Jan 1, 1918

By Timothy M. Barton

The U.S. Bureau of Mines is conducting research to assess the effectiveness of different chain pillar designs in maintaining gate entry stability. A particular concern is ground control for deep-cover 1ongwalls located at depths in excess of 1,000 ft. The study described in this report was performed in two experimental sections in one longwall headgate section which contained three different pillar designs. Two of the designs used conventional abutment pillars, while the third was a total-yielding pillar system. Both of the test areas were located under 1,800 ft of cover. The purpose of this study was to evaluate the effectiveness of these three pillar designs for gate road stability. As the longwall mined passed the test areas, Bureau engineers monitored entry convergence, roof sag, and changes in roof quality. The study indicated that the all-yield system performed nearly as well as the better of the two abutment pillar systems; but all of the three designs would have failed to provide acceptable stability for second panel mining without considerable artificial support.

Jan 1, 1989

By David Garry, Michael J. Brnich, Lynn L. Rethi, Henry P. Cole, William J. Wiehagen, Roberta A. Calhoun

This document contains most of the materials needed to use the exercise. The main part of the document is the instructor's copy. It tells how to use the exercise, presents the objectives, the master answer sheet, the scoring key, and discussion notes to be used following the exercise. The next section summarizes results from field tests of the exercise, and reports the miners' evaluation of the activity. The last part of this document is three appendices. Appendix A is the exercise problem booklet. This booklet can be duplicated locally. The booklets are reusable. One is needed for every person in the classroom. Appendix B is the answer sheet and the trainee's questionnaire. Copies of this answer sheet must have the latent image (invisible) ink answers that appear in Appendix C printed on them.1 Answer sheets are consumable. One is needed for each person or each small group of persons who work the exercise. Exercise Summary Read this section first. It determines if the exercise is appropriate for your classes. If you choose to use the exercise, examine the table of contents and review the remainder of this document. Type: Latent image Audience: Supervisors, Safety Personnel and Accident Investigators Length: Eight questions (30 minutes for administration plus 30 for discussion) Skills: Developing a strategy or plan to prevent slips and falls Following correct procedures in conducting an accident investigation Preventing unsafe work practices Recognizing and instituting hazard controls in the section Identifying and implementing safe work procedures Location: Underground coal mine section Problem: You have been the general mine foreman at White Rock Mine for 4 years and have worked at this mine for 12 years. The mine superintendent calls you into his office. He gives you an accident report of an employee in 4-G section who was injured while carrying rock dust bags from the rock dust car to a battery powered scoop. It is several days after the accident and the mine superintendent assigns you and the safety supervisor to thoroughly investigate the accident to determine all the contributing factors. Your job is to make specific recommendations to prevent future slipping/tripping accidents.

Jan 10, 1999

By R. Larry Grayson

In the October 1998 issue of the Holmes Safety Association Bulletin, NIOSH authors Mark Stephenson and Carol Merry wrote the article Hearing loss among miners and measures to protect hearing, which focused on the extensiveness of hearing loss among miners and the use of hearing protection to prevent hearing loss. While the primary importance of engineering controls in preventing hearing loss was discussed, since miners do not generally have control over their work en­vironment or assignments, the article focused on the importance of consis­tent use of hearing protection. In this article, all aspects of a compre­hensive approach to the prevention of hearing loss in miners will be covered. The discussions will do the following: ? describe application of the hierarchy of controls in preventing hear­ing loss in miners, ? give an example for each type of control measure and its impact, ? explain the major provisions, be­yond the hierarchy of controls, of the recent NIOSH document en-titled Criteria for a Recommended Standard: Occupa­tional Noise Exposure, Revised Criteria 1998 relative to a hearing loss prevention program, and ? summarize important points on control of noise exposure for every miner to remember, equipment in most facets of operations. Miners are well aware of noisy areas in or around equipment, icluding extraction machinery such as draglines, power shovels, longwall shearers, and continuous mining machines; powered haulage equipment such as load-haul-dumps, shuttle cars, large trucks, and continuous haulage units; roof bolting machines; jackleg drills and stopers; auxiliary equipment such as compressors, fans, and pumps; size reduction equipment, etc. They are not well aware of the insidious nature of pro­gressive hearing loss, which is per­manent, but they are generally aware of what levels of noise are hazardous and what measures can be taken to reduce their personal noise exposure. Behaviorally, however, there are many reasons why miners choose not to use hearing protection faithfully.

Jan 1, 1998

By D. Randolph Berry

Foster-Miller Associates has developed a set of guidelines to permit hoist manufacturers, mine owners, and MESA mine inspectors to design, purchase, install or inspect a safe and effective Emergency Escape Hoist, as required by the Coal Mine Health and Safety act of 1969. A series of surveys were carried out to determine: 1. The attitudes and local needs of the MESA District Managers. 2. Current escape hoist installations. 3. Equipment available for future designs. 4. Foreign methods and equipment for mine rescue. From these survey studies, preliminary guideline objectives were developed.

Jan 1, 2012

By T. J. Rohrbacher

This report presents a U.S. Bureau of Mines methodology developed to incorporate factors of coal production (mining and cleaning methods, recoveries, economics, etc.) into the definition of recover-ability of a coal resource. Project procedures and computer models that were developed to include mine and preparation plant production rates, recoveries, and costs are explained. The results of these procedures and models are reviewed and compared to the Energy Information Administration estimate of U.S. coal resources-the "demonstrated reserve base." The Matewan 7-1/2-minute quadrangle in eastern Kentucky was selected to demonstrate the methodology.

Jan 1, 1993

Past issues of Minerals and Materials have discussed such aspects of the economy as consumption and investment expenditures, interest rates, productivity, and international trade barriers and their effect on the minerals industry here and abroad. In this issue, we will (l) look at recent indications of a possible economic recovery, (2) present 1983 expectations reflecting the results of industry surveys conducted by the U.S. Department of Commerce (DOC), and (3) briefly discuss the contribution of the U.S. mining industry to total gross national product (GNP). THE RECOVERY Throughout most of 1982, DOC's Composite Index of Leading Indicators provided evidence of impending improvement in the economy. The index increased moderately during eight of the months in 1982 and then jumped an estimated 3.6 percent in January 1983 (table 1). While the leading indicators continued to predict improvement, the general economy, as measured by the Index of Industrial Production, continued its slide through November 1982 (table 2). Finally total industrial production increased in December 1982 and continued on an upward path in January and February, as predicted by the leading indicators.

Jan 1, 1983

By A. A. Bakewell

This information circular, which describes mining methods and practices at the Baguio Gold Mining Co., Philippine Islands, is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs. Since January 1952, Baguio Gold Mining Co. has operated its rehabilitated mine and mill in the Baguio district. Postwar labor and supply costs are three or four times prewar costs, whereas ore tenor and tonnage are about the same. Ore reserves remain approximately the same, but deeper and more spreadout operations add to increasing costs. Recently the company has acquired an adjoining property, which may lengthen its life substantially. Costs and general operations are more or less typical of the district, which includes three other active gold mines. Gold ore mined in the district totals approximately 4,300 tons per day.

Jan 1, 1959

By Terrence J. Stobbe

The authors investigated the nature, cause and treatment of 234 back injuries which occurred in 156 different situations in underground coal mines. A detailed interview was conducted with each injured miner as 137 variables were explored to provide a complete picture of the injury scenario. The miners worked at 23 mines in six states. An important finding of the study was that sudden movement, which occurred in 527 of the injuries, is a more frequent factor than heavy lifting in causing hack injuries. Along with sudden movement, other major injury causing factors were equipment seat design, lifting, cable handling, and slips/trips. No significant differences were found between the injury scenarios associated with lost time and non-lost time injuries; thus, both sets of scenarios should he used in doe loping back injury control strategies. Medical treatment and rehabilitation varied in content and quality. Dialogue between the medical, rehabilitation and mining communities is needed to develop an effective treatment strategy. Back injury control related training was found to be inadequate in most mines. Mine specific training for physical stress recognition and potential sudden torte release should he added to the training currently given. Based on the information collected in this study, recommendations were made regarding equipment design, mechanical assists and procedures for material handling, training, etc., which, if implemented, will assist in reducing the frequency of back injuries in underground coal mining.

Jan 1, 1989

By Timothy J. Rohrbacher

This report presents a U.S. Bureau of Mines study that incorporates coal mining factors, coal recovery factors, and economic factors into the definition of an economically recoverable coal resource. The relationship between these factors to the Energy Information Administration's estimate of U.S. coal resources-the "Demonstrated Reserve Base"-is discussed. The Boltsfork 7 1/2-minute quadrangle in eastern Kentucky was selected as the study area. Results indicate that of the original 280.2 M tons of resource in the quadrangle, only 99.8 M tons (35.6%) is recoverable at a mining cost of $25 per ton or less.

Jan 1, 1994

By Ann G. Kim

Fires that occur in abandoned coal mines, waste banks, and in coal outcrops constitute a serious health, safety, and environmental hazard. Toxic fumes, the deterioration of air quality, and subsidence constitute the greatest hazards from these fires. Although tires on abandoned mined land (AML) occur in every coal-producing state, the severity of the problem varies. Methods to extinguish or control AML fires, including excavation, fire barriers, and sealing, are generally expensive and have a relatively low probability of success This U.S. Bureau of Mines report includes information from a variety of sources, i.e., agencies of the Federal Government, State agencies, research reports, conference proceedings, product information, and technical literature. This information has been collated into a comprehensive discussion of AML fire problems. Data on past fire control projects and on the estimated extent of the current problem have been compiled. Factors affecting the occurrence, propagation, and extinguishment of AML fires are discussed. Conventional fire control methods are described, and their probable effectiveness is evaluated. Information on the hazards of AML fires and safety considerations is included. The status of current technology, recent improvements in fire control methods, and areas of current research are discussed.

Jan 1, 1993

By T. L. Johnston

A review of technical literature of the last quarter century discloses that much experimental work has been carried on in an effort to develop commercial processes for making sponge iron. In addition to the work that has been recorded, other work has been done the results of which have not been published. The degree of success or failure of these investigators does not detract from the fact that the problem has its challenging aspects and practical possibilities that encourage further investigation. The purpose of this report is to record information derived from recent experimental work that .had its 'objective the development and demonstration of one method of producing sponge iron. Work of other investigators was studied and applied wherever possible.

Jan 1, 1948

By B. J. Moore

This publication contains routine analyses and related source data for 278 natural gas samples from 14 States. All of the samples were collected during calendar year 1973 as part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576.3 Fifteen previous publications have presented the results of 10,201 gas analyses prior to 1973. The first three, Bulletins 486,4 576,6 and 617,6 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other 12 publications,7 which were issued as information circulars, supplement the three bulletins and contain 4,983 analyses of samples collected since 1960. This publication is the 13th publication supplementing the three bulletins.

Jan 1, 1974

By A. N. Baldwin

This report documents work performed under Bureau of Mines Contract J0265029 to study and develop two innovative mining systems: ? An underground auger capable of augering into the right and left ribs without repositioning the machine ? A conventional mining system employing recently developed innovative machinery. The report is separated into two volumes to document the two studies separately. Volume I describes work performed and the recommended concept for a bidirectional auger. Volume II describes the studies of mining equipment performance and mining plane developed to determine a conventional mining plan offering improved productivity.

Jan 1, 1977

A symposium was held on January 30 and 31, 1973, at Pittsburgh, Pa., to review the state-of-the-art in designing and utilizing diesel-powered equipment in underground mining. The Health and Safety Activity of the Bureau of Mines sponsored the symposium with major assistance from the following four participating organizations: The American Mining Congress J. Allen Overton, President The United Mine Workers of America Arnold R. Miller, President The National Independent Coal Operator's Association Cloyd D. McDowell, President The Bituminous Coal Operators' Association, Inc. Guy Farmer, President Seventeen papers were presented during four half-day sessions devoted to the general subjects of the diesel engine, the place of the diesel in underground mining, health protection using diesels underground, and maintaining safety of diesels underground. Eleven of the speakers were from industrial organizations here and abroad; one represented the Provincial Government of Nova Scotia; two were with the Department of Health, Education, and Welfare; and three reported on Bureau of Mines work related to diesels.

Jan 1, 1975

By Frank E. Williams

Nuclear detonation data were accumulated, studied, and evaluated by the Bureau of Mines to visualize how nuclear explosives might be used in a shale?-oil industry, The evaluation shows that the Green River Formation at the semi-isolated locale of Piceance Creek Basin, in northwestern Colorado; is thick and widespread enough to warrant consideration of nuclear mining in lieu of conventional methods, Because cost data for nuclear explosions are limited; cost comparisons are made largely by assumptions. Also described are the history of the shale-oil industry, the geology and size of oil-shale resources; and conventional mining methods and processing technology.

Jan 1, 1969

By David A. Andrews

Coal occurs at many scattered localities in Arizona, California, Idaho, Nevada, and Oregon, but in most of the known occurrences thick coal beds are of small extent and the coal generally contains a high percentage of impurities. The coal beds occur at many different horizons in strata of Cretaceous and Tertiary age. Bituminous coal has been found in several areas, the most extensive of which is the Eden Ridge field of Oregon. Lignite also occurs in many places, but the only extensive deposit is in the Goose Creek field of Idaho, Nevada, and "Utah. The coal reserves of the region are largely of subbituminous rank; most of the subbituminous coal is in the Black Mesa field of northeastern Arizona and the Coos Bay field of Oregon. The Black Mesa field contains more than 80 percent of the coal reserves of all ranks but is remote from both transportation facilities and centers of consumption. Substantial reserves ill the Coos Bay field are favorably situated with respect to transportation and markets. ARIZONA Subbituminous coal occurs in the Black Mesa, Pinedale, and Gallup coal fields in Apache, Navajo, and Coconino Counties, Ariz. (fig. 1). Bituminous coal occurs in the Deer Creek field in Pinal and Graham Counties and in a small area in Apache County at the north-east corner of the State. All the coal beds are in strata of Cretaceous age. The coal in the Gallup field and at the northeast corner of the State lies in the Western edge of the San Juan structural basin. "Vest and south of this basin the coal-bearing strata have been removed by erosion except in high mesas.

Jan 1, 1947

By J. Adkins

This document presents a description of the results of a project aimed at producing a broad description of current mining training programs and an evaluation of their effectiveness with respect to reducing mine injuries. Aggregate training and injury data were used to evaluate the overall training effort at 300 mines as well as specific efforts in twelve categories of training course objectives. From such evaluations, recommendations were derived with particular emphasis being placed on identifying program characteristics that tend to be associated with effective training. Recommendations were also formulated with reference to role changes in industry and government interaction with respect to training programs, new or additional training programs, changes in the types of course materials and training methodologies, and recommendations concerning new areas for investigation.

Jan 1, 1976