Search Documents

Provide roof to floor closure rate measurements during underground mining, especially retreat mining of coal pillars, thereby helping the miners predict an imminent roof fall. Approach An electronic device and rugged potentiometric extensometer were developed to provide a means fur measuring total closure and the rate of closure. How It Works An intrinsically safe, battery operated instrument is enclosed in a rugged, hand carried field case. The unit is constructed using low-power, integrated circuits to provide minimal battery drain. Two digital Light Emitting Diode (LED) readouts are used; one displays the rate, the other displays the total closure. The unit will measure one extensometer continuously or two extensometers alternately. Two potentiometric extensometers with a closure measurement range of 6 inches are attached to the readout unit. As the roof to floor closure changes, the potentiometric resistance

Jan 1, 1982

Objective: To improve the effectiveness of dust collector capture on surface mine drills.

Oct 1, 2005

By W. M. Merritts, Charles Findlay, Stephen Krickovic

Methane emission rates were studied in a Pittsburgh coalbed mine in northern West Virginia. A fullface boring-type continuous miner, equipped with a methane monitor, was used in the development of a set of eight main headings, one side of which was near old workings; the other side abutted virgin coal. Two air splits ventilated the section. Air volumes and methane percentages were recorded, and time studies of the miner were made during five consecutive operating days, during which a complete cycle of mining the headings and one line of related breakthroughs was accomplished. Methane emission rates increased significantly as mining progressed from the side near old mine workings toward the virgin area, and generally increased with coal extract ion. Mining in the heading immediately adjacent to virgin coal was interrupted quite frequently, owing to excessive methane concentrations at the face, despite adequate air volumes and acceptable methane concentrations in the immediate return airway.

Aug 1, 1970

By R. E. Morgan

[IN COMPILING the table of analyses of this bulletin every available source of information was studied. These sources, as listed at the end of the table, were many and varied, and it believed that the tabulation gives the best general information obtainable. However, its known accuracy and completeness of coverage necessarily fall far short of published data on coals of the United States. A table of world production of coal and lignite, as and published by the Bureau of Mine, of world resources of coals, brown coal, and lignite, as published in the Yearbook of the World Power Conference, 1948, are included for convenience of the reader. The six continental maps at the end of the bulletin show the general location of the principal coal fields.]

Jan 1, 1952

By Abdurrahman Cetinbas

The effect of water infusion on the flow of methane and on the production of dust was investigated at an active face in the Pittsburgh coalbed. The average total flow of methane at the face decreased by approximately 79 percent, whereas the flow from the ribs increased about 24 percent after infusion. On the day after infusion, dust concentrations appear to have been reduced; however, the presence of large quantities of rock dust obscured the results on the following days.

Jan 1, 1972

By B. W. Gandrud, A. C. Richardson

"INTRODUCTION The Bankhead mine of the Cane Creek Coal Mining Co. is in the central part of Walker County, Ala., 4 miles south of Jasper. The Mary Lee bed in this part of the State yields a practically free-burning coal which is marketed as a. steam-raising and domestic fuel. As mined, the coal ordinarily contains ash-forming impurities to an extent that makes it necessary to treat the coal by some washing process before it is marketed. At present the Bank-head coal coarser than 3-1/2 inch is hand-picked and the coal finer than 3-1/2 inch is washed in two single-compartment jigsThis paper contains the result of screen-sizing and float-and-sink tests on a representative sample of the run-of-mine coal and the results of tests made to show the amount of coal liberated from impurities by crushing the coarser sizes. .This report is one of a series on the washability of Alabama coals which is being prepared by the U. S. Bureau of Mines and the University of Alabama, with the cooperation of the coal producers of Alabama.SAMPLING AT THE MINE'The Mary Lee bed at Bankhead consists of two benches separated by a rock parting which varies in thickness from place to place in the mine. The top bench has a very uniform thick-nest; throughout the workings and yields about 65.0 per cent of the output. The bottom bench varies greatly in thickness and in nary places becomes too thin to work at a. profit. The sample for the washability study was taken underground at a place which was typical of the mine as a whole. In taking the sample the working face was squared up and a representative section out from each bench. Care was taken to secure a, quantity of coal from each bench proportional to the quantity contributed to the mine output. The rock parting as gobbed in accordance with the usual mining practice. The total sample taken weighed 3 tons."

May 1, 1933

By J. Douglas Causey

The Bureau of Mines conducted mineral investigations of the Peace Rock and Deadwood River roadless areas in Idaho, in 1992. Literature research was done by the Idaho Geological Survey. The study areas contain black sand placers (thorium, columbium, tantalum, titanium, uranium, and rare earth elements), gold, and molybdenum prospects. Except for unrecorded placer gold, there has been no mineral production from the areas. No mineral resources were delineated, but a multi-million tonne molybdenum resource is in the Big Pine Creek area and a 142 million m' black sand deposit is in the Stolle Meadows, Peace Valley, and Deadwood River areas. The Deadwood mine produced zinc, lead, and silver. There are six mining districts in and adjoining the areas; Warm Lake, Deadwood, Garden Valley/Lowman, Banner, Summit Flat, and Grimes Pass. Few claims, mostly placer, were active in the study area in 1992. The study areas are underlain by granitic rocks of the Idaho batholith. Most of the deposits are alluvial accumulations of heavy minerals weathered out of the Idaho batholith. Stockwork and narrow veins along shears account for the base and precious metal concentrations. Eleven prospects were examined. Workings consist of drill holes, pits and adits. Geothermal resources (hot springs) occur mainly along the Middle Fork Payette River; Vulcan Hot Springs is a designated Known Geothermal Resource Area. Sand and gravel resources are of local interest.

Jan 1, 1993

By Danny A. Riley, James R. Sanger, Hani S. Matloub, Lin-Ling Zhang, Ji-Geng Yan

This experimental study was done to determine pathological feature of vibration injury to the peripheral nerves in the hind limbs of rats exposed to 7 days of vibration. Materials and Methods Animals: Twenty four male Sprague-Dawley rats weighing 350-400 grams were randomly divided into two groups: sham control group and vibrated group. To document vibration-induced changes in the experimental model, the sciatic nerve was used because it contains both motor and sensory fibers and is relatively superficial in the posterior thigh. Customized Vibrating Platform: The hind limbs of the rats in the vibrated group were exposed to vibration in a custom-built vibrating apparatus consisting of two platforms: a smaller vibrating platform on which the hind limbs of the rat are secured, and a larger platform on which the remainder of the body rests. The vibration parameters (frequency 43.5 Hz, amplitude 1.5mm, acceleration 4.75G, velocity 6cm/sec., and displacement of 3.0mm) of this model were measured. Methods: Rats were anesthetized with 35mg/kg of intraperitoneal Nembutal (phenobarbital) and their hind limbs fixed to the vibrating platform by Velcro loops. Both hind limbs rest on the vibrating platform while the remainder of the body rests on the larger platform. The rats were vibrated 4 hours a day, for 7 days, with close monitoring of the vibration parameters. The 4-hour duration of hazardous vibration was based on recommendations from the British Standards Institution. The sciatic nerve of rats not exposed to vibration, but similarly anesthetized and secured to the vibrating platform, acted as controls. At the end of seven days of exposure to vibration, nerves from both the vibrated rats and the control rats were harvested after perfusion of the lower half of the body using glutaraldehyde as described below. Neural Fixation: The aorta was cannulated, and the inferior vena cava was nicked and the animal was initially perfused with 0.9% buffered sodium chloride. This was followed by perfusion of a filtered mixture of 3% glutaraldehyde and 3% paraformaldehyde fixation solution, The tissue was subjected to post fixation by routine. The neural tissue was then submitted for light and electron microscopy. Results While light microscopy showed minimal histological differences between vibrated (n=12) and control nerves (n=12), the changes revealed by electron microscopy were dramatic. These included thickening of the epineurium, as well as thickening of the myelin sheath as compared with normal nerve. Also, the axon plasma was detached from the myelin sheaths, and many vacuoles were seen between the myelin laminae(Fig.1); These changes were found in all vibrated animals, and in the whole segment of each vibrated nerve. Myelin balls, consisting of

Jan 6, 2006

By M. G. Zabetakis

Amyl nitrite (C5H11NO2) is a pale-yellow liquid with an ethereal fruity odor and a pungent aromatic taste. Its use in first-aid treatment of cyanide poisoning has been suggested by Chen and his coworkers. Although not the most effective treatment, it is the only one that does not require intravenous injections and is, therefore, very suitable as a preliminary measure, which only involves breaking a capsule near the patient's nose until intravenous injections can be given. In the case of the sodium nitrite -sodium thiosulfate treatment, for instance, such injections require about 15 minutes. As amyl nitrite "Pearls" (small capsules containing liquid amyl nitrite) are placed in many first-aid kits by various companies that handle, store, or use hydrogen cyanide gas, it appeared advisable to investigate the explosion hazards of this material in air and oxygen. Accordingly, tests were made to determine the limits of flammability, temperature range of flammability of amyl nitrite saturated with air and with oxygen, and minimum ignition temperatures of this material in air and in oxygen.

Jan 1, 1952

By T. M. Klemetti, G. M. Molinda, D. M. Pappas

Some of the most difficult coal mine roof in the U.S. can be found in the Illinois Basin. Factors contributing to the high roof fall rate include: weak moisture-sensitive roof rock, high horizontal stress, and limited longwall mining. The depth of cover ranges from 90-1,000 ft and roof damage from horizontal stress can be severe. Moisture sensitive-roof rock is common above the Springfield-Harrisburg Herrin #5 and #6 seams in the Illinois Basin, and contributes to roof skin deterioration. The roof fall rate increases significantly in the humid summer months. The National Institute for Occupational Safety and Health (NIOSH) has shown, using lab and field studies, that highly moisture-sensitive roof rock can be directly correlated to poor roof conditions. Controlling the skin is the key to reducing rock fall injuries, and roof screening is, by far, the best remedy. Illinois Basin coal operators have been successful in reducing the number of rock fall injuries in recent years. NIOSH has documented best practices for screen installation which has resulted in safe, efficient operations. Other solutions to skin failure include: the use of denser five bolts per row patterns to reduce spans between bolts, systematic supplemental support in intersections, straps and large pans protecting operators, and air conditioning to remove moisture from the intake air.

By R. E. Head

[This paper embodies the data obtained by a detailed statistical, microscopic analysis of the composite mill feed concentrate, and tailing from the Magne and Arthur mills of the Utah Conger Co. for 1 month in 1929. It is one of a series of papers by the same authors5 dealing with the mineralogical characteristics of the ore and concentration products from various well-known plants. The work was done in the cooperateive microscopic service laboratory at Salt Lake and represents the results of cooperation between the United States Bureau u of Mines, the Utah Copper Co. and the University of Utah.]

Jan 1, 1935

By R. E. Head

This paper embodies the data obtained by a detailed statistical, microscopic analysis of the composite mill feed concentrate, and tailing, from the Magne and Arthur mills of the Utah Conger Co. for 1 month in 1929. It is one of a series of papers by the same authors dealing with the mineralogical characteristics of the ore and concentration products from various well-known plants. The work was done in the cooperative microscopic service laboratory at Salt Lake and represents the results of cooperation between the United States Bureau of Mines, the Utah Copper Co., and the University of Utah.

Jan 1, 1935

By Hugo E. Camargo

Noise Induced Hearing Loss is the most common occupational disease in the U.S. and of paramount importance in the mining industry. According to data for 2006 from the Mine Safety and Health Administration (MSHA), Continuous Miner operators accounted for 30.2% of underground mining equipment operators with noise doses exceeding the Permissible Exposure Limit (PEL). This figure becomes more significant considering that 49% of the 2006 national underground coal production was extracted using continuous mining methods. Thus, there is a clear need to reduce the sound radiated by Continuous Mining Machines. The first step towards efficient noise control of a Continuous Mining Machine requires identification of the various noise sources under controlled operating conditions. To this end, a 42-microphone phased array was used in conjunction with 4 reference microphones to sample the acoustic field of a machine in the Hemi-anechoic chamber of the Pittsburgh Research Laboratory. These data were processed using a frequency-domain beamforming algorithm to obtain acoustic maps of 5 sides of the machine. The focus of the test was on the conveyor noise since previous studies showed that operation of the conveyor is the most important contributor to the sound radiated by the machine. From the acoustic maps, the following potential areas for noise control were identified, and included: chain-tail-roller interaction, chain flight tip-side board interaction, and chain-upper deck interaction.

Jan 1, 2008

By Alexander May

The Bureau of Mines conducted studies to determine if phosphogypsum, a waste material from the processing of phosphate rock, contains hazardous toxic materials as defined by the Environmental Protection Agency (EPA) and whether leaching of these toxic materials and radium may occur. Samples of the phosphogypsum stockpiled material were evaluated using the EPA extraction procedure, atomic absorption, neutron activation, x-ray diffraction, and chemical and physical means. Radiological tests performed used both the germanium-lithium and emanation methods. The data show that the phosphogypsum stockpiles are not hazardous toxic waste as defined by EPA criteria. Trace elements and radium are not leached from the phosphogypsum stockpiles. Absorption of trace elements and radium by phosphogypsum is the major reason for their not being leached. The standard error of measurement of radium concentrations was 4.7 pCi/g.

Jan 1, 1983

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSHA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. nonmetallic mining workforce from March through September 1986. Similar reports have been prepared for the metallic, stone, and sand and gravel mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the cool mining sector.

Jan 1, 1988

By H. M. Smith

In studying the chemistry of lubricating-oil fractions from so-called ?paraffin-base? crudes, one of the first requisites is a method for the separation and removal of waxy material. A method utilizing solvents for this purpose is described in this report, together with preliminary experiments with solvents that led to its development. The solvents actually used are secondary butyl alcohol, acetone, and mixtures of these.. Isopropyl alcohol was also studied. Preliminary Experiments In previous work on "intermediate-base" crude oil, following the work of Wyant and Marsh acetone had been used for laboratory separations of oil and wax. Then acetone was tried for the separation of the waxes and oils of "paraffin-base" crude, the volume of acetone required (80 parts to 1 part of oil) was found to be too great for large-scale work. For this reason the effectiveness of other solvents was studied; the separation by acetone, however, was used as a standard.

Jan 1, 1927

By C. A. Rhoades

The spillage that accumulates under conveyor belt lines presents a possible fire and explosion hazard fomiinqjetsoruiel, especially to those who must clean up the spillage. The U.S. Bureau of Mines conducted research to reduce this hazard by identifying and investigating the parameters affecting the efficiency of conveyor belt cleaning. The amount of material carried back under the conveyor and the wear rates of metal cleaning blades decreased with increasing blade-to-belt pressure to a limiting value, after which the carryback and wear rates remained essentially constant. The optimum blade-to-belt pressure was found to be 11 to 14 psi for the research conveyor system. Greater pressures increased the blade-belt friction without improving either cleaning or blade life. The modes of blade wear were three-body abrasion and slurry erosion caused by the sand-lime test mixture. Wear rates were reduced by increasing the metal hardness, opti-mizing the pressure, and removing conveyor belt imperfections. Corrosion was not observed to affect the wear of various steels in tests of less than 34 h. The results of this study should allow mine operators to run their conveyors under conditions that will maximize cleaning and minimize equipment wear.

Jan 1, 1989

By Roy E. Peterson

The Bureau of Mines conducted bench-scale research to evaluate materials which showed potential as low-cost reductants for use in the ironmaking industry. These materials were lignite, subbituminous coal, coal char, tree trimmings, refuse--derived paperboard, used crankcase oil, and peat. To compare their effectiveness, the materials were tested in the reduction roasting of nonmagnetic taconite and, except for oil and peat, in the reduction of iron oxide pellets to metallized pellets. Reduction was conducted in a 18-cm-diameter, rotary drum, which was externally heated in an electric furnace. Over 92 pct of the iron was magnetically recovered from a nonmagnetic taconite after roasting with any of the reductants, but greater quantities of reductant were required to achieve this when the waste materials were used. The fossil fuels were also more effective for metallizing pellets, although metallizations above 90 pct were also obtained with tree trimmings and refuse paperboard. However, refuse paperboard had to be frequently recharged to the furnace because it depleted rapidly.

Jan 1, 1983

By Mark I. Copeland

A study was conducted to determine if commonly used alloying additions or coating materials can prevent the formation of a liquid-copper phase during the reheating of copper-containing steels. If so, the tendency of such steels to surface-crack during hot-working might be eliminated. Steel specimens were scaled by heating them either isothermally or in a programed manner that simulated industrial furnace practice. Metallographic examination of the heated specimens showed that molten fayalite (Fe2Si04) completely prevented the formation of liquid copper at the surface. Fayalite, which melts at 2,200° F (1,205° C), was formed by internal oxidation of the silicon contained in the steel. By forming complex molten oxides, coatings of borax glass were also effective in preventing the occurrence of liquid copper at the steel surface.

Jan 1, 1972

By Robert A. Miller

This computer program determines the price per ton of coal needed to obtain a profit of 12 percent discounted cash flow. From a predetermined equipment and manning list, the program calculates all costs and prints seven tables, Including the equipment and manning tables and the discount cash flow table. Forty-four of the input variables may be readily changed to study their effects upon the final price per ton of coal or upon individual cost items. The method is adaptable for any type of mining and with additions, for beneficiation processes. This program was written in Fortran IV for use on the IBM 11302 and with few modifications can be used on other computers.

Jan 1, 1971