Search Documents

INTRODUCTION The pager phones used in many underground coal mines are battery- operated, party-line telephones with provisions for loudspeaker paging. The system is two-wire, non-polarized, and is operated by self-contained batteries. Many of the individual units are certified as permissible. Requirements for installation are specified in state and federal regulations, such as in the Code of Federal Regulations, Title 30, Mineral Resources, Part 75. The major federal regulations that affect communication in coal mines are noted below, with a brief description of the subject matter in each of the relevant paragraphs. Refer to the cited paragraphs of Title 30 for explicit details of these regulations. (This brief description is for reference purposes only.) Minimum Requirements (paragraphs 75.1600, 75.17 13-2, and 75.1003-1) Approved telephone or two-way communication will be provided between the surface and each main shaft landing and each working section ; to the nearest medical assistance; and shall be protected from contact with trolley wires or trolley feeder wires. Installation Requirements (paragraphs 75.5 16-2, 75.52 1, and 77.508-1 ) Communication wires will be supported on insulated hangers, attached to messenger cables, or buried, to protect against mechanical damage ; installed opposite trolley wires; and insulated near power conductors . . . each cable will have lightning arresters within 100 feet of going below ground . . . and arresters will be provided wherever telephone wires enter a building. Wire and Cable Requirements (paragraphs 75.5 16-2, 75.5 17, and 75.52 1) Communication cable means two or more insulated conductors, covered by an additional abrasion-resistant covering; power wires and cables shall be adequately insulated and fully protected; and lightning arresters shall be connected to low-resistance grounds, more than 25 feet from neutral grounds.

Apr 1, 1975

By R. P. Vinson, D. P. Tuchman

The personal dust monitor (PDM) is a sampling device developed for measuring the personal exposure to coal mine dust of mine workers. The device is based on proprietary technology known as the tapered element oscillating microbalance (TEOM) originally developed as a fixed- site environmental particulate mass monitor by Rupprecht and Patashnick Co., Inc., Albany, NY. Currently, the monitoring of exposure to coal mine dust relies on periodic samples taken by traditional coal mine dust sampling units that use a cyclone, filter, pump, and laboratory measurement of the filter mass. Better measurement of mine dust levels has been the goal of industry and labor for nearly two decades. PDM technology offers accurate, end-of-shift and near real time assessment of worker dust exposure. Laboratory and underground tests compared measurements taken by a prototype PDM-2 (a two-piece TEOM) to the average of multiple personal dust samplers monitoring the same space. In the range of mass loadings P between 0.5 and 4.0 mg/m the PDM met a 25% accuracy criterion 95% of the time with 95% confidence. However, some questions still exist about potential bias between types of coal. The prototype two-piece device is in the process of being combined into a single unit that also contains the miners' cap lamp creating a more ergonomic dust sampling system.

Provide an accurate, reliable means for determining when a sealed mine or mine section can be safely reopened after a fire. Approach The Bureau of Mines performed a research investigation that resulted in the development of a mathematical formula for deriving a quantity, called RATIO, which can be used to define when a sealed mine or mine section has returned to safe recovery conditions after a fire. Research Results There were two major results from this Bureau research. Over a period of several years, the Bureau of Mines conducted six experiments at its Bruceton Experimental Mine in Pennsylvania. The experiments involved sealing the mine after several tons of piled coal had been allowed to burn continuously for 2 to 3 days. Although gas data obtained during the experiments revealed nothing significant, measured smoke particle levels were found to correlate with the stages of combustion and temperatures of the smoldering coal pile. Moreover, it was found that no smoke particles are produced when high-temperature smoldering exists deep within the mass of the coal pile since the smoke particles are filtered by the coal surrounding the hot region. Smoke is emitted into the mine atmosphere only if combustion is occurring near exposed surfaces. As suggested by these findings, any decision to recover a sealed mine area based primarily upon the absence of smoke particles is not a wise derision.

Jan 1, 1988

By Joseph A. Perry

One goal of the Bureau of Mines is to develop technology tp insure a dependable supply of minerals to the United States. To support this goal, the Bureau's Albany Research Center has modified a commercial atomic absorption spectrophotometer to rapidly determine trace levels of mercury by cold-vapor atomic absorption spectrophotometry. Such diverse materials as ores, mill products, stream water, sediments, and flue dust have been analyzed. A very high dynamic range of 0.2 ng/ml to 1 µg/ml of mercury in solutions is routinely analyzed by this instrument.

Jan 1, 1981

By John H. Soulé

"INTRODUCTION The Mining Branch of the Bureau of Mines has used the wagon drill to sample mineral deposits in New Mexico. This method of sampling was successful and con¬stituted an important phase of the work on five exploratory projects undertaken in 1943, 1944, and 1945. The deposits varied in topographic features, geology, mineral content, and in the physical characteristics of the rocks drilled. The altitudes ranged from 630 to 7,800 feet. Three hundred and seventeen holes totaling 6,852 feet were drilled. The deepest hole was 66 feet; the average depth was a little less than 22 feet.The results of the above-mentioned work form the basis of this report. Special attention is given to the later and more improved techniques used. This report was written with the expectation that the procedures might prove advantageous to others in the exploration and sampling of near-surface mineral de¬posits, and that a more extended use of the technique might result.AcknowledgmentsAcknowledgment is due Charles H. Johnson, chief of the Rolla Division, Mining Branch, for helpful suggestions in starting this work, and to J. H. Hedges, chief of the Tucson Division, Mining Branch, W. R. Storms, engineer-in-charge of the Silver City, N. Mex., Field Office, and Donald H. Mullen, mining engineer attached to that office, for assistance in preparing and editing this report."

May 1, 1947

To provide a faster means to open and close permissible electrical enclosures. Approach: An inspection and repair port with a multiple start thread which provides a permissible joint has been developed and tested. How It Works: The inspection port screw thread has a large pitch, which allows the port cover to be rotated from fully closed 10 fully open, in less than one revolution. See Figure 1. When the cover is screwed back in. it be-gins engagement within one eighth turn because the screw design has eight separate threads. To prevent Its unauthorized opening, the port cover has a bolt guarded by ears which accept a padlock. The threads are designed to tolerate a reasonable amount of grit without binding, although wipe-off cleanness is necessary during reassembly. Enclosures of two different sizes each fitted with the quick-access port, were

Jan 1, 1976

By T. G. Carnahan

The Federal Bureau of Mines investigated, on a laboratory scale, a technique for recovery of silver from pregnant solutions generated in the hydro-metallurgical treatment of complex base-metal sulfide concentrates with oxidizing chloride media. This technique provides a means for recovery and simplified reduction of accessory silver to metal from chloride solutions. The method consists of adding NaI or KI to the solution to precipitate AgI, which is then contacted with Na2S to produce Ag2S and to regenerate the iodide salt solution. Silver recoveries range from 99 pct with 20 pct excess iodide precipitant, to 92 pct when the theoretical stoichiometric amount of precipitant is employed. The Ag2S product can be reduced to silver metal by contact with aluminum chips in NaOH solution followed by purification with conventional fire refining techniques.

Jan 1, 1980

Control the release of ground-water into active underground coal workings by short-term pumping from dewatering wells sited on fractures. Approach The sudden release of fracture-stored groundwater into underground coal workings often occurs when mine workings are developed beneath fracture valleys, Pumping from fracture trace-sited dewatering wells, prior to development of the underlying workings, can be an efficient means of intercepting fracture-stored groundwater before it is released into the mine. Dewatering operations are discontinued once the underlying mine workings have been fully developed, and the maximum possible reduction in fracture storage has been achieved through pumping. How It Works An aerial photographic technique known as fracture trace analysis is used to site dewatering wells on rock fractures in a valley bottom. Downhole caliper and temperature logs are used to assess the fracture flow potential of each dewatering well drilled.

Jan 1, 1987

By Oliver Bowles

"In a previous report of the Bureau of Mines (Serial No. 2080 reference was made to a fatal accident from falling rock in a quarry in Utah, and ways of avoiding such accidents were pointed out. A fatal accident similar to it in some respects recently occurred in a limestone quarry in Maryland. All operators of stone quarries are desirous of reducing accidents to a minimum, and almost without exception they welcome any suggestions having in view the establishment of safer quarry practice. It is believed, therefore, that a brief outline of the cir-cumstances surrounding this later accident may be of practical advantage to quarry-men, as it may serve as a guide to them in so conducting operations that such unfortunate occurrences may be reduced in number.The quarry where the accident occurred is in form a circular pit 500 to 600 feet across an 80 to 100 feet deep. The rock is a dense limestone with the beds dipping at an angle of 35 to 45 degrees from the horizontal. Numerous erosion cavities in the form of pockets or narrow spaces following joint planes are filled with red sand and clay. They are confined largely to the upper 20 or 30 feet of the deposit. Open bedding planes are 4 to 10 feet apart toward the surface, and are spaced at wider intervals toward the base of the quarry. The open bedding planes present smooth uniform rock surfaces that dip steeply into the pit at the northeast side of the quarry opening. These smooth surfaces constitute a source of danger, as they may permit loose material to slide into the pit.In this particular instance a blast had been discharged, throwing down a mass of rock for steam-shovel loading. Three men wore employed thereafter for a period of about two days in cleaning down all loose material that might be dangerous to workmen luring the loading process. A mass of red sand and clay in which several large bowlders were embedded was left on one of these slanting surfaces, for the material seemed to be sufficiently secure to be quite safe. The lower edge of the slanting surface was about 25 feet above the quarry floor. The quarry conditions are illustrated in fig. 1, where (a) represents the quarry floor, (b) the vertical quarry (c) the slanting joint plane surface, and (d) the rock and earth resting on the surface."

Dec 1, 1921

By Bruce D. Sartwell

The Bureau of Mines is using characteristic X-rays produced by proton bombardment of a solid surface to provide quantitative compositional analyses of surface layers of metals. An integral X-ray yield equation has been developed that quantitatively relates the measured X-ray yield to the thickness of thin films ranging from less than a monolayer to several thousand angstroms. The use of the integral yield equation is demonstrated for the growth of a thin film by vacuum evaporation. Results are presented that show haw proton-induced X-ray emission (PIXE) has been used to determine the oxidation kinetics of iron that had been implanted with several different species of heavy ions. The sensitivity of PIXE for the measurement of very-thin-film growth kinetics is demonstrated from studies of the effect of fractional mono-layer coverages of sulfur on the initial oxidation kinetics of iron. Results are also presented in which PIXE has been used to study the redistribution of alloying elements in components of a gas turbine that had fractured due to corrosion fatigue. By combining PIXE with low-energy ion sputtering, quantitative composition depth profiles of surface layers are obtained. Examples are presented for the profiling of iron samples implanted with 25-kev nickel ions and for a platinum coating on an Fe-5Cr substrate.

Jan 1, 1980

The twelve latexes listed in Table XI penetrated A horizon soil as shown by elution through a laboratory soil column and gave good sealing efficiency. See details in Table XII. High elution through laboratory soil columns of 4 to 6 inches depth is desirable because it predicts penetration of latex to a greater depth in the field. No definite correlation was evident between penetrating ability and particle size, surface tension, or pH. Most of the materials, however, were characterized by low surface tensions in the 36 to 53 dynes/cm range while particle sizes were usually in the intermediate range of about 1500 to 2500 Å. Naugatex J-3471 (a highly crosslinked styrene-butadiene copolymer) was the most promising of this group for stability, penetrating ability; and sealant efficiency. It also showed utility with [B] profile soil. Many of the other latexes tested in this investigation showed good sealing efficiency but were judged unsatisfactory because they gave low penetration or formed surface films with & horizon top soil. In general, latexes containing cationic surfactants were not satisfactory because they formed a heavy surface film. This is due to neutralization of the positive latex charge by the negatively charged soil particles.

Jan 1, 1972

By Mary S. Esfandiary

This list of organizations that conduct research and development programs on coal has been compiled by the Bureau of Mines with the thought that such a directory may provide a useful guide to worldwide research efforts in the areas designated and may facilitate communication between organizations with similar interests. This list includes government, university, private, and commercial organizations. Many of these groups are conducting comparatively modest but often particularly interesting or specialized investigations. The areas of investigation have been defined in a broad manner--these include analysis and constitution, mining and geology, preparation, combustion, briquetting, high- and low-temperature carbonization, gasification, hydrogenation, Fischer-Tropsch, and health and safety. In some instances such information is not available, but the names of the organizations themselves often indicate immediate arias of interest. Special publications issued by and describing the work of each organization have been cited, when known; almost all of the organizations also publish results of their investigations in the technical press. Several foreign technical and trade publications that include such information and are not published directly by any of the organizations listed are cited in the pages following the list of organizations in each country. This list is not complete. Information that would improve coverage and/or accuracy will be welcomed by the Bureau of Mines.

Jan 1, 1961

By Clyde M. Pearce

The Lake Superior iron-mining district includes parts of the States of Michigan, Minnesota, and Wisconsin. The laws of each State provide for an industrial commission and for inspection of mines. The following extract from the General Orders on Mines, effective October 25, 1937, issued by the Industrial Commission of Wisconsin, is the only reference to the use of safety catches on mine cages or skips found in the laws and regulations in the Lake Superior iron-mining district: Order 316 - Cages for Hoisting Men. (c) Sides, Gates, and Safety Catches. ***Every cage shall be provided with safety catches of sufficient strength to hold the cage with its maximum load at any point in the event the hoisting cable should break. (d) Testing Safety Catches. The safety catches of cages and skips used to hoist men shall be kept well oiled and in good working order. They shall be tested at least once each month by tying up the cage or skip with hemp rope, lowering a few feet of hoisting cable on top of cage, then cutting the hemp rope, provided that any other system of testing, which is equally effective, may be used.

Jan 1, 1945

By H. P. Hermance

Preliminary examinations of the Parker and Webb deposits were made by E. E. Maillott, Bureau of Mines engineer in July 1942. The chemical and spectrographic analyses included in this report wore made at the Eastern Experiment Station of the Bureau of Mines at College Park, Md., under the general supervision successively of S. M. Shelton and of Paul M. Tyler, formerly regional engineer, Eastern Region. Beneficiation tests were conducted under the supervision of Frank D. Lamb. The mineral exploration was under the general supervision of J. D. Bardill, formerly district engineer. Acknowledgment is gratefully made to the St. Joseph Lead Co., in particular to John S. Brown and P. J. Mechin for their assistance. Special acknowledgment is made to the American Metal Co., Ltd., ,Ind to T. C. Moore for furnishing core-drill and assay data; to the Universal Exploration Co. and P. B. Jennings; and to the Northern New York Mining Corp. and C. H. Sprague for their permission to publish the core-drill dta. Excellent cooperation was given by Dr. W; M. Agar and C, L. Rogers of the Geological Survey.

Jan 1, 1949

By W. A. Cole

As the mines get older and the active workings get Farther and farther away from the original mine openings, it becomes increasingly difficult and expensive to ventilate most coal-mines properly. At the same time, the avenues of escape for those employed underground have become so extended' as often to make it impossible for them to make their way out of the mine in the event of a fire, mine explosion, or other emergency. Where such Conditions exist, the only satisfactory solution is to make new ventilation and emergency-escape openings near the active mine workings. At most mines this would necessitate sinking shafts, which is often slow and expensive.

Jan 1, 1945

Provide an economic alternative to drill-blast excavation with the same ability to excavate openings of varied orientation, shape, and size. Approach Develop an efficient, adaptable, mechanical excavation machine that produces unconfined tensile failure in rock. How It Works A drill-split fragmentation machine that combines a drill and a unique splitter has been developed. The drill and splitter are mounted on a carriage that positions the splitter in a hole immediately after it is made by the drill. The splitter creates force loads that cause the rock to fragment, and the process is repeated for excavation. The unique splitter applies both radial and axial loads to the rock mass, which produces an excavation action comparable to pulling a plug. This excavation action distinguishes the radial-axial splitter from typical demolition splitters, which require a free surface parallel to the axis of the splitter toward which to break rock.

Jan 1, 1989

By Henry G. Dorsett

This report is a description of equipment and test procedures used by the Federal Bureau of Mines in laboratory studies on the explosibility of dusts. The principal tests concern ignition temperature, minimum explosive concentra¬tion, minimum electrical energy for ignition, limiting oxygen concentration, pressure, and rates of pressure rise. As new materials often present unique problems, variations in the general procedure and special tests performed are indicated, The general procedures for handling a dust sample from its receipt at the laboratory to the preparation of the report are described. The repro¬ducibility of the respective tests are shown. A brief history of laboratory studies on dust explosions by the Bureau of Mines and a description of current equipment and test procedures used are presented in this report. Its purpose is to facilitate interpretation of data previously published and those proposed to be published on the numerous mineral, agricultural and industrial dusts that have been studied. Through understanding and interpretation of the laboratory data obtained for the parameters of explosibility, preventive measures can be adopted for alleviat¬ing the hazard of dust explosions arising in manufacturing and processing industries.

Jan 1, 1960

By David R. Forshey

This Bureau of Mines report presents a quantitative theoretical analysis of a coupled gasdynamics-heat release system involving the kinetics of water condensation in and behind the rarefaction wave in a shock tube using the method of characteristics. The merger of characteristics to form a shock wave is included.

Jan 1, 1977

By F. K. McIntosh, L. A. Dahmers

"INTRODUCTION North Carolina has been the leading producer of mica in the United States, accounting for roughly 50 percent of the Nation's output. The producing area is a belt some 100 miles in width lying in the Mountain and Piedmont sections in the western part of the State. Ashe, Watauga, Avery, Mitchell, Yancey, Buncombe, Haywood, Jackson, Macon, Transylvania, Rutherford, Cleveland, and Lincoln Counties supply the bulk of production, while small amounts have been produced in Gaston, Catawba, Burke, Wilkes, Yadkin, Stokes, and Person Counties.To assist the operators and expedite the production of mica during the recent emergency, the Bureau of Mines drilled four of the more promising mica properties in this State. The results of this exploratory program are recorded in this report.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Division, L. B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyzes samples and makes beneficiation tests."

Apr 1, 1948

The coal-bearing regions of Colorado cover approximately 29,600 square miles, which is 28.4 percent of the state's total area. The most important coal-bearing regions are located in the north western and west-central parts of Colorado. Coal resources vary from lignite to anthracite. More than 70 percent are bituminous; 23 percent subbituminous; 5 percent lignite; and less than 1 percent anthracite. The state's coal reserves total about 17.2 billion tons, 3.5 percent of national reserves. Approximately 8.8 million acres of coal rights in the state are owned by the Federal Government; on about 72percent of this land, the Federal Government controls both the coal and the surface rights. It is estimated that approximately 4.2 billion tons of coal reserves are under federal ownership in Colorado. Permitted acreage of mines in Colorado ranges from 40 to 13,114 acres. Differences in elevation create many climatic zones in Colorado. Local annual precipitation can average less than eight inches in some areas in extreme western Colorado to more than 30 inches in certain mountainous areas. Generally, precipitation rates are low at most mine sites, making revegetation difficult. Colorado gained primacy when its regulatory program was conditionally approved December 15,1980. The Abandoned Mine Land Program was approved June 11, 1982.

Jan 1, 1992