Search Documents

By D. G. Hulbert, D. Tudors, M. L. Coetzee, I. K. Craig

The paper describes how a multivariable control scheme was developed and implemented for the run-of-mine milling circuit at a gold mine belonging to Vaal Reefs Exploration & Mining Company Limited. The key variables that are controlled are slurry level in the sump, mass of material in the mil, and product size. The control scheme has resulted in reliable control of the dynamics of the plant, and has provided a good basis for the optimization of plant operation by the selection of suitable set Points.

Jan 1, 1990

By V. Riihimäki, M. Luotamo

The Unit of Toxicological Risk Assessment of the Finnish Institute of Occupational Health (FIOH) is conducting a 'Health Risk Assessment for Metallic Chromium and Trivalent Chromium' under the sponsorship of the International Chromium Development Association (ICDA) and the International Stainless Steel Forum (ISSF). This risk assessment will be conducted in accordance with the current European Union legislation in force (Council Regulation 793/93/EEC, Commission Regulation 1488/94/EEC, Dir. 67/548/EEC), but also to meet the regulatory obligations as set out in the European Commission REACH legislation proposal (Consultation Document, the Registration, Evaluation, Authorisation and Restrictions of CHemicals). Further aims include outlining the criteria for the setting of occupational exposure limits for metallic chromium and trivalent chromium compounds. Human Health Risk Assessment according to the current legislation shall entail hazard identification of the toxic end points (acute toxicity, irritation/corrosivity, sensitisation, repeated dose toxicity, mutagenicity, carcinogenicity, reproductive toxicity) including, as appropriate, dose (concentration) - response assessment, and derivation of the N(L)OAELs (No (Lowest) Observed Adverse Effect Level) and/or DNELs (Derived No Effect Level). Exposure assessments for workers, consumers and humans exposed via the environment take into account all the known intended uses. Risk characterisation will compare the typical and/or reasonable worst case exposure estimates to the N(L)OAELs or DNELs to determine Margins of Safety (MOS) for all human populations by each exposure scenario and type of effect, followed by conclusions about the presence or absence of risk. Although all of the key elements of existing legislation remain in REACH, the principal change is that, the burden of proof will be transferred from the member state authorities to industry. The new proposed format of Chemical Safety Report (CSR) will include Risk Management Measures (RMM) as an essential part of the report in addition to the risk assessment. The RMM plays a role in the evaluation of further testing needs and advocating reasons for possible waiwer of requirements. The research programme started in March 2002 and will be completed within the time frame of two years.

Jan 1, 2004

The April General Meeting of the Institute was held in Kelvin House, Johannesburg, on 16th April, 1969, at 4.30 p.m. Mr R. C. J. Goode (president) was in the Chair. There were also present nineteen Members, including Messrs R. J. Adamson, F. P. Bath, J. K. E. Douglas, A. R. C. Fowler, P. Lambooy, D. G. Maxwell and J. A. Nixon, (Council Members), Messrs E. L. Atkinson, I. R. Chaston, J. L. Edwards, J. S. Hall, S. A. Hancox, A. F. Lee, W. K. B. Loftus, H. S. Simpson, A. N. Shand, R. A. Wilson, H. J. Wright and J. E. Van Leeuwen. Nine Associate Members, including Messrs O. Davel, G. Douglas, P. R. Garcia, D. J. Murphy, D. Rankin, G. Schwartz, H. N. Singer, S. Thompson and D. A. Viljoen. One Graduate Mr D. Bosley. Ten Visitors, including Messrs S. Adler, C. E. Alvey, B. J. Botha, K. Chant, L. W. Davis, R. N. Guest, R. V. Keet, E. G. Keown, M. D. Lourie and S. McMurray. Secretary Mr D. C. Visser. Total present: Fourty-one. MINUTES The President requested that confirmation of the minutes of the previous meeting be held over as they would only be appearing in the Journal of the following month. Agreed. MEMBERSHIP The President: "I have much pleasure in announcing that the names of the under-mentioned candidates, having been published in accordance with By-law 5.2.2, Council has elected them to membership of the Institute in the following grades: Members: Kenneth Sinc1air Rae, Ian Robert Malcolm Chaston. Associate Members: Norman Isaac Thomas, Ian Connell Robinson. Graduates: Simon Richard Jeremy Perkins, Bleddyn Reginald Lear, David Williams. Affiliate: Richard Robert Will. Students: Angus David McElwee, Clive Renard Archer, Peter Andrew Locke. MEMBER TRANSFERRED TO A HIGHER GRADE From Graduate to Associate Member: Patrick James Burns. I welcome the newly elected members to the Institute and congratulate the member who has been transferred to a higher grade." (Applause). GENERAL BUSINESS The President reminded members that a buffet supper at a cost of 55c would be available after the meeting. PAPER FOR PRESENTATION The President noted with pleasure that a strong contingent from De Beers and the Finsch Mine were present. He expressed gratitude to Mr Loftus for coming

In China, thin coal seams are rich in resources but are technically challenging. The mineable reserves in these seams account for 20.4% of the total coal resources, while the current production accounts for only 10.4% of the total annual production. Characteristics such as narrow mining space, low level of mechanization, poor working environment, and high cost of mining, restrict the development of mining safety and efficiency. Recently, fully mechanized mining technology has developed rapidly for thin coal seams, the level of yield and efficiency has reached or exceeded the international standard, and some state-owned key coal mines are considering automation of their mining process. In thin coal seams with hard stone bands that contain concentrations of pyrite, a specialized software, LS-DYNA, is used to calculate the rational blasting parameters that are used in the deep-hole pre-splitting blasting. Using this method the hard stone bands are fractured effectively, and hence increasing the coal productivity. In addition, mining advance rate were increased by enhancing the level of fully mechanized equipment and safety improved by increasing gas drainage from the gas outburst prone seam located some 7 m below the coal horizon. At present, thin coal seam mining technology faces many challenges, including the low level of equipment automation, the low advance rate in mixed coal-rock ground, and the large number of the mine personnel underground. By lowering the labour intensity and improving efficiency through automation and other measures, more efficient working faces can be implemented in thin coal seams.

Jan 1, 2012

By A. Moerman, M. Verreault, V. Falmagne

Noranda has been involved in the development of technologies for automated mining vehicles since 1988, and has contributed in transferring the technological foundation for the suite of SIAM products now being commercialized by STAS. Some of these technologies are now mature and available for commercial implementation in operations where a strong business case can be made for the use of automation. Noranda has successfully implemented or is commissioning the Tele-remote, Auto-loading and truck Guidance technologies at two of its operations, based on operating needs and economic justifications. Operator acceptance, training and maintenance issues have been addressed in order to ensure the reliability and availability of the automation components. These represent the most significant challenges encountered and addressed during the implementation period.

Sep 1, 2001

A Life Cycle Assessment (LCA) of stainless steel production, including that of the nickel, ferronickel, ferrochromium and iron feedstocks was carried out using inventory data derived from the literature. The environmental impact categories considered in the study were Global Warming Potential (GWP), Acidification Potential (AP) and total (or full cycle) energy consumption. The effects of different sources of electricity (black coal, natural gas and hydroelectricity) were also examined in the study. The results of the LCA showed that when ferronickel is used as the nickel source, the total energy consumption for stainless steel production is approximately 50% higher than when nickel metal is used as the nickel source (75 MJ/kg cf. 49 MJ/kg). This result comes about largely because the Fe units in ferronickel have a much higher energy intensity than do the Fe units in pig iron, and the greater the use of the former at the expense of the latter, the greater is the total energy consumption. The results also showed that the production of ferronickel made by far the largest contribution (59%) to the total energy consumption for stainless steel production when this feedstock is used as the nickel source, but when nickel metal is used as the nickel source the contributions of the various stages are more evenly distributed. It was also observed that the electricity consumption of the electric furnaces used in the production of ferronickel, ferrochromium and stainless steel contributed approximately 50% to the total energy consumed in stainless steel production. Given the relatively low efficiencies associated with electrical power generation, significant reductions in the total energy of stainless steel production could be anticipated if more direct use of thermal energy was made in the ferronickel, ferrochromium and/or stainless steel smelting stages, for example by utilising bath smelting processes.

Jan 1, 2004

By J. Muller

Keywords: Pyrometallurgy, blast furnace, slag viscosity, slag liquidus temperature, phase equilibria The viscosity of molten slag in blast furnace operations is an important process variable, influencing the rate and location of reactions inside the furnace, as well as the ease with which the final slag could be removed from the furnace. To optimize these processes, it is necessary to estimate the slag viscosity and liquidus temperatures as accurately as possible, and know the target values. Models to predict viscosities and liquidus temperatures, incorporating phase equilibrium calculations, have been developed and validated with measured data. Various diagrams have been developed to illustrate how the properties vary with composition and temperature, including pseudo-ternary diagrams of SiO2-MgO-CaO-Al2O3 for viscosity and liquidus temperature. Models were also applied and methodologies developed to analyse historical blast furnace operations and determine target values.

Jan 1, 2011

By V. Yahorava

Ion exchange is considered to be an effective technology for the removal of various impurities from cobalt advance electrolytes. With the correct choice of resin, ion exchange can consistently remove the required impurities to the levels for the production of high-grade cobalt metal. Although ion exchange was in the past used primarily for nickel removal, more recently it has been also considered for the removal of copper, zinc, and cadmium. Generally, granular ion exchange products are used, but Mintek is currently evaluating ion exchange fibres for a number of applications, including the removal of copper from cobalt advance electrolytes. Fibrous ion exchangers have major advantages compared to granular resins in that they have significantly higher reaction rates, and wash water volumes could be limited. Granular and fibrous ion exchangers were evaluated and compared for the removal of copper from cobalt advance electrolyte. A synthetic electrolyte containing 50 g/L cobalt and 50 mg/L copper was used for the test work. Equilibrium isotherms, mini-column tests, and split elution tests were done. The results were used to size a full-scale operation to treat 100 m3/h of electrolyte. The potential cobalt losses or recycle requirements were estimated, and data to calculate indicative operating costs for each adsorbent was generated. This information was used for a techno-economic comparison of granular and fibrous ion exchange systems for the removal of copper from cobalt advance electrolyte.

Jan 1, 2014

A typical sub-level block cave mining extraction method employs an undercut level to establish a cavity in hard rock, and as such requires special support methods and products to be installed during the development phase. The undercut level development in the block cave orebody is then sacrificial, and support elements will eventually report to the crusher and perhaps conveyor belt systems for transportation to surface. The choice of support products installed in the undercut level development should take cognizance of the detrimental effect these could have on the mining system such as cutting of conveyor belts, obstructing crushers, safety aspects, and productivity. This work explores the probability and practicality of making use of new-generation support products to make the operation safer as well as enhance productivity in the development phase and during the undercut operation. This paper will investigate the use of glass reinforced plastic(GRP) rockbolts and GRP mesh instead of conventional steel bolts and mesh along with resin capsule-filled holes with the GRP bolts. Complementing this with thin spray liner (TSL) application as another means of creating a safer operating environment, as well as a productive support medium, will also be addressed. These proposed items are envisaged to reduce production downtime and improve the safety of our people. These items are all easy and light to handle, cuttable and crusher friendly, as they will break up during the crushing process.

Jan 1, 2012

By N. C. J. Dempers, J. A. L. Parker, R. A. Wildenboer

More than half of global cobalt reserves are located in the Southern African Copperbelt, stretching over the northern tip of Zambia and southern area of the Democratic Republic of Congo. In these areas, cobalt is not typically produced as a primary product but as a byproduct of copper production. Ores from this region often contain uranium, which is readily leached under typical copper leach conditions and enters the process. Uranium does not pose a challenge to copper production, but it becomes a significant problem when it follows cobalt to the cobalt precipitation process and results in unacceptably high levels of U in the final Co product. This paper evaluates the existing process technologies that can be used to remove uranium from cobalt-bearing process streams, including phosphate precipitation and ion exchange. Advantages and disadvantages of the uranium removal processes are discussed, and important design considerations are highlighted.

Jan 1, 2023

By G. Lyman

The cross-belt sampler is a device that is very widely used even though it has not been ratified by the Standards associations. This paper is concerned with the bias testing of two cross-belt sampler designs against stopped belt samples and a cross-stream cutter at the belt end. The bias analysis is carried out using size distribution as the analyte and conventional t-testing and the Hotelling T squared test, which are compared for their effectiveness. The paper considers the issue of detectable bias and the statistical planning of bias tests.

Jan 1, 2009

By K. P. Davey

In 1998 an initial objective was given to the author, to process valuable off grade High Carbon Ferro Manganese (FeMn) metal fines profitably. The previous attempts that had been made to re-melt these metal fines through the furnaces had resulted in poor furnace operation, mainly to do with lack of electrode penetration and furnace bed permeability. It was decided that the method to resolve these problems was to agglomerate the metal fines. During the study on the agglomeration of the metal fines, a decision was made to use furnace baghouse dust and stockpiled furnace baghouse dust and sludge (DSF) as a ?filler? in the metal fines. The primary reason for using baghouse dust was to eliminate an environmental hazard, whereas the secondary reason for using the DSF was to utilize manganese units contained in the dust. The off-grade metal fines and dust were compacted using a brick press, with cement and aluminum rich plastic clay as a binder, to obtain agglomerate that was cost effective. Through the re-melting of the agglomerated off-grade metal fines, it was realized that this agglomerate concept could have other uses, that of replacing ores on the furnace, at a lower cost. The agglomerate recipe was changed to create an agglomerate that had a high manganese to iron ratio, this replaced Comilog ore on the furnaces, thereby reducing overall furnace unit costs. Future work concerning agglomeration, is to reduce furnace costs further through agglomerating .0.5mm ultra ore fines and .0.3mm Gloria and Nchwaning sludge. Using this agglomerate replaces a portion of the Gloria and Nchwaning lumpy ore on the furnaces at a lower cost. This would eliminate problematic material that exists at the ASSMANG Manganese mines.

Jan 1, 2004

By R. Castro, R. Gómez, F. Betancourt, M. Moncada

In block cave mining, rock fragmentation is a key parameter that influences the production level design and mine planning. Fragmentation occurs mainly by natural breakage during the caving process and in the draw column. The breakage that occurs within the column is known as secondary fragmentation. Secondary fragmentation has been successfully described using the block caving comminution model, which replicates the fragmentation mechanics between particles under drawn and vertical loads in a draw column. This model is based on a kinetic and population balance approach, in which non-normalized and normalized assumptions can be used depending on material and comminution system behaviour. In this paper, the non-normalized and normalized approaches are applied and compared to laboratory data to determine which assumption should be used for secondary breakage in block caving. Approaches are compared graphically, with the mean square error and the Fisher test with a false-rejection probability of 0.05. Based on a statistical analysis, the results show that the normalized model can be applied to all the rock types tested.

Nov 1, 2021

By J. Tikka, E. Bäcklund, N. -O. Lindfors

Tornados are the most violent weather events in the world, and we have all seen the forces and phenomena created by tornados in nature. Airgrinder AB has been working with a material treatment technology, which most easily could be described as an artificial tornado. The process consists principally of one air fan providing a high-velocity airstream that enters a mechanical cyclone. When the gas enters the cyclone, an outer vortex is created. This outer vortex rotates next to the cyclone wall, and at the bottom of the cyclone funnel the gas stream is turned and an inner vortex is created. The control of the air flow is tuned by a special device on top of the cyclone. The gas outlet is at the top of the cyclone and the material outlet at the bottom. The material is fed through a feeding device into the air stream channel prior to the inlet into the cyclone. The process is basically an improved grinding and dehydrating system, which is very efficient and environmentally friendly and can even be employed with very sticky materials. Also due to its rotating comminution, the material particles become rounded during grinding, hence more free flowing and easier to handle. MEFOS has already tested more than 30 different applications in the pilot equipment. The materials tested range from metallurgical slags containing 2?3% moisture to sludges with up to70% moisture. This technology has a potentially strong impact on mineral beneficiation, including the drying of sticky fine-grained materials, improved and selective gas scrubbing and the manufacture of free flowing powders.

Jan 1, 2007

By S. Erçayhan, B. Derin, O. Yücel

In the present study, the production of low carbon ferrochromium (LC-FeCr) from chromite concentrates containing 55.09% Cr2O3 and 13.06% Fe via metallothermic process was investigated. For this aim, in the experiments, the aluminothermic reduction method was applied in an open crucible. 10% CrO3 + 10% NaClO3, 15% CrO3 + 5% NaClO3 and 20% CrO3 by weight of concentrate were added to the charge, respectively and the charge was reduced with aluminium. The experiments were done with the additions of 90, 100, 110, 120 and 130% of stoichiometric requirement of aluminium. The highest Cr content in alloys was found as 71.7% at 120% of stoichiometric Al whereas the highest Cr recovery in alloys was found as 71.8% at 130% of stoichiometric Al when the both charge contained 15% CrO3 + 5% NaClO3 by weight of chromite concentrate.

Jan 1, 2004

By S. Stuurman

Inorganic acids such as sulphuric acid have found use together with certain reducing agents in leaching of copper-cobalt oxide ores. These reagents are not ideal due to the adverse effect the inorganic acids generally have on the environment and the high costs of the reducing agents. In this study a copper-cobalt oxide ore from the Central African Copperbelt was leached in two different environments; sulphuric acid in conjunction with hydrogen peroxide as a reducing agent and tartaric acid. The effects of acid concentration, reducing agent concentration, and temperature were independently determined for both leaching environments. The sulphuric acid concentration was varied between 0.4 M and 1.2 M and the concentration of hydrogen peroxide between 4.0 M and 6.5 M, while the tartaric acid concentration was varied between 0.15 M and 0.35 M. The temperature was varied between 20°C and 50°C. The results showed that the extraction of both copper and cobalt increased with sulphuric acid concentration, reaching a peak at approximately 0.8 M and then decreasing at higher acid concentrations. A similar increase and decrease in metal extraction was observed when the reducing agent was increased. In leaching with tartaric acid, the extraction of cobalt was much higher than that of copper, although extraction of both metals increased with acid concentration. Additions of small amounts of hydrogen peroxide were found to increase cobalt extraction in tartaric acid but had a minimal effect on copper. An increase in the solution temperature had a significant effect in the organic acid environment, with the effect on cobalt extraction being much more pronounced than on copper.

Jan 1, 2014

By M. H. Lampen

The SILAG Material Tracking System MTS monitors and controls the complete material flow throughout the plant - and even companywide. The customized system developed by Siemens especially for bulk material handling applications enables companies to track bulk material from the mine to the harbor, to the steel mill or to the power plant. All relevant material data is available at every single step of the material’s journey. SILAG is an open, scalable system based on Windows NT / 2000. Using standard interfaces of Windows NT, like API, ODBC, SQL and socket technology, the system is very flexible and can easily be tailored to meet different requirements. SILAG can be used as a stand-alone solution or - if complete plant control and visualization is required - as a component of a fully integrated automation system with the Win CC HMI system and the PCS7 process control. In contrast to conventional material tracking systems, SILAG offers many advantages. - The Material Tracking System is an object oriented, online to the process, linked system. All changes in the plant during operation e.g. selecting another conveyor route, start and stop etc. will be automatically detected and will influence the calculation. - The systems is able to split and blend material (quantity and quality).Measurements of tonnage, volume or quality analysis can be linked online to the system. Each movement of material is monitored by the system and leads to online recalculations of the images and databases. - All material data is based on 3D-stockpile images, which are calculated by an internal mathematical model based on quantity and quality information. - If a laser scanner is available on a stockyard machine it can be taken to update the profile directly from the piles. - Efficient control and report functions are available on each, free selectable point of the total plant.

Sep 1, 2001

By J. -C. Tricket, W. A. Düweke, S. Kock

The high-resolution three-dimensional (3-D) seismic reflection data acquired for Impala Platinum between 1998 and 2002 in the western Bushveld Igneous Complex form an integral part of Impala?s mine planning and development programme. These data are of sufficiently high quality to provide unprecedented 3-D models of the geological structure of the Merensky Reef and UG2Chromitite Reef, from which the mine deduces the size, geometry and distribution of mineable blocks. Conversely, the seismic data details zones of un-mineable ground caused by structural disturbances in the form of potholes, fault zones and pegmatoid intrusions. Furthermore, variations in dip and strike are well imaged, allowing the mine planners to optimize the mine design and layout. Current interpretation work is focused on enhancing the accuracy of these geological model seven further through the analysis of ?seismic trace attributes.? Preliminary testing on the Impala Platinum 3-D seismic volume has shown that attribute analysis has the potential to illuminate a number of geological reef disturbances that are otherwise ?invisible? in the original seismic time volume. Potential areas of improvement include inter alia: ?Improved definition of major fault zones ?Improved definition of zones of reef depression (?slumping?) ?Identification of reef terracing and/or reverse dip.. Keywords: 3D reflection seismics; Impala Platinum Ltd; seismic attribute analysis; Seismic Micro Technology (SMT); rock solid attributes; dip-azimuth; instantaneous phase and similarity.

Jan 1, 2004

By J. M. Stewart

Although the incidence of heat stroke in South African gold mines is small, work continues on its reduction. This paper proposes limits of heat stress that are applicable to South African underground conditions, with the warning that they should not be extrapolated to other situations without careful consideration having first been given to their limitations. These limits of heat stress take physical and physiological considerations into account, and they correspond to there being a 10-6 risk of an essentially nude man developing a rectal temperature in excess of 40°C. It is recommended that further work should be undertaken on the development of equations for the calculation of the heat transfer from clothed men, the derivation of equations that quantify the physiological conductance and sweat rate response of humans, and on establishing the frequency distributions that describe variations in rectal temperature response between individuals in different types of environment.

Jan 1, 1981

By K. C. Mills, R. Thackray

A test has been devised that can predict accurately the % crystallinity developed in a slag film formed between the steel strand and the mould. The % crystallinity in the test samples was determined and compared with that for slag films formed in the mould when casting with that flux. There was good agreement between the % crystallinity in the test samples and the slag films. It was found that additions of TiO2and ZrO2had little effect on the amount of crystalline phase formed, but additions of CaO caused a dramatic increase in the amount of crystalline phase formed. Various parameters (which can be calculated from chemical composition of the flux) have been plotted against % crystallinty in the test samples. It was found that the modified (NBO/T) ratio provided the best relation with % crystallinity for the various parameters tested. There commended relation is % crystallinity=141.1(NBO/T)-284.0. Keywords: continuous casting, mould flux, slag film, crystallinity, chemical composition

Jan 1, 2004