Search Documents

By T. S. Kagogo

The factors affecting haul truck tyre performance and the effectiveness of the management system at Rossing Uranium Mine were investigated with the aim of increasing tyre performance in terms of running hours until failure. The main objectives were to identify the types of tyre failure, their causes and cost implications, and evaluate the effectiveness of the management system. A site severity survey, weight study, and TKPH studies were conducted to determine the pit conditions, and an analysis of failed tyres carried out. The results showed that tyre performance at the mine has declined from 2009 to date, and the increase in lost value amounted to R5.7 million in 2012 alone. The main cause of tyre failure is loose rocks in the pit. The present management system in the load and haul department is not effective enough due to operational constraints it is facing.

Jan 1, 2014

By S. Hlajoane, L. S. Mokhahlane

The demand for rare earth elements has increased around the world due to their application in a variety of technological advancements. Previous studies have evaluated the potential of the rare earth elements and yttrium (REY) hosted within the Permian coal deposits of the main Karoo Basin (MKB) in Southern Africa. However, not a lot of scientific research has gone into the Triassic coal deposits. The Triassic coals in South Africa were the first coals to be exploited for their thermal use in the 1880s, but the discovery of the higher rank and more abundant Ecca coal deposits led to the Triassic coals remaining largely unexplored. The demand for rare earth elements has sparked interest in these coal deposits as potential sources for valuable minerals. Late Triassic coal deposits in Lesotho have previously not been well documented and these low-rank coals can be a potential source of rare earth elements. This study aims to characterize and evaluate the potential of REY in the Taung coal deposit, southwest of Lesotho. Coal and associated argillaceous samples from the Taung coal deposit were analyzed using microscopic petrography for coal characterization and an inductively coupled plasma mass spectrometry (ICP-MS) to determine the amount of rare earth elements. Taung coal is classified as middle medium rank D bituminous coal. The total REY content in Taung coal and its associated rocks range from 162.9 ppm to 855.1 ppm, which is significantly higher than the upper continental crustal (UCC) average. The average critical REY concentration of samples from the Taung coal deposit is 189.4 ppm, which is three times higher than that of the Chinese Bayan Obo deposit. Samples classified as very promising and promising because of their outlook coefficients, are found to contain up to 77% of critical REY. It is envisioned that the area could be a prime deposit for these REY.

Nov 6, 2024

By H. Cevizci

"Numerical simulation of the plaster stemming method (PSM) was performed and compared with the conventional drill cuttings stemming method (DCSM). Many earlier in situ tests have proved that PSM can use the blast energy more efficiently than DCSM. Despite PSM generating more blast vibrations, it has advantages over DCSM such as better fragmentation and lower cost per unit volume of rock blasted. In this study, numerical simulation with Autodyn software using a 2D tool was employed to prove the efficiency of plaster stemming by comparing parameters such as pressure, Y-velocity, Y-force, internal energy, acceleration-Y, and compression. For example, the maximum pressure attained at the top of explosive column was 7 395 MPa for DCSM whereas it was as high as 11 945 MPa for PSM. Most of the computed parameters were significantly higher in PSM than those obtained for DCSM. This paper is the first study elucidating the efficiency of PSM by numerical simulation. It is concluded that PSM can save substantial amounts of money and effort. IntroductionThe stemming of blast-hole collars in surface mines with an inert material redirects blasting energy to the rock more efficiently, thus the blast-induced energy is utilized more effectively in breaking rock. With proper stemming, the gases should not escape due to loose stemming material. More efficient stemming with better confinement therefore increases the blast fragmentation. In addition, the distance of scatter is increased, giving rise to a looser rock pile that can be more easily loaded and transported. In order to improve the performance of a blast, stemming is used to help maintain the gas pressure over time (Konya and Konya, 2018). Proper stemming has been shown to increase the explosive efficiency by over 41% (Snelling and Hall, 1912).The most common stemming material in open pits and quarries is drill cuttings because of their ready availability at blast sites and the drill cuttings stemming method (DCSM) is a low-cost method. However, it has a major disadvantage in that dry drill cuttings eject very easily from blast-holes during an explosion, thus a great percentage of the blast energy is wasted and lost to the atmosphere. Cevizci (2012, 2014, 2013, 2017) studied blasting parameters in open pits and obtained better results with the plaster stemming method (PSM) in many limestone, basalt, and clay quarries. Moulding plaster is preferred for stemming because of the fast hardening time of 25–30 minutes."

May 1, 2019

By M. Ataei, F. Sereshki, R. N. Masir

Given the inherent risks and disruptions in underground coal mining operations, strengthening the resilience of critical infrastructure has become a vital priority. This paper aims to evaluate the resilience of the underground coal mining environment using historical data and expert judgment. The study serves as a framework for optimising the utilisation of critical infrastructure to minimise operational disturbances. To achieve this, a practical methodology has been developed, incorporating nearly two and a half years of collected operational data, a hierarchical structure, and a systematic approach. Furthermore, a case study is conducted to demonstrate the real-world applicability of the proposed method. Finally, the resilience index isintroduced as a straightforward summation of ranked impact factors, providing a clear metric for resilience assessment.

Dec 15, 2025

By T. P. Letsebe, L. Magwaza, T. A. Sethu, S. M. Rupprecht

"The authors were tasked with introducing safe and efficient drilling and blasting practices to a small artisanal mine located in the Eastern Province of Rwanda. The current mining methods employed at the mine are inefficient as rockbreaking is conducted utilizing hammer and chisel, or by drilling and blasting with no understanding of the rockbreaking process. The paper discusses the drill and blast cycle, as well as the associated activities necessary to support the mining cycle. The challenges and critical aspects in implementing drill and blast activities are discussed, as well as some of the technical aspects, i.e.drilling pattern, initiation and timing of the blast, and handling of misfires. Ancillary issues such as ventilation, training, communication, effective planning, logistics, and human relations are also examined. IntroductionRockbreaking accounts for 60% of the direct mining costs in small-scale mining. When drilling and blasting practices are poorly implemented the process becomes inefficient and dangerous. The introduction of a proven drill and blast system to artisanal mining offers a number of challenges, with safety being considered the backbone of any sustainable operation and a standard that cannot be compromised.The paper is based on a project at an artisanal cassiterite (tin) mining operation in a small village in the Kayonza District in the Eastern Province of Rwanda. A drill and blast programme utilizing industry best practice was introduced at an underground development end; a raise developed at an inclination of 23 degrees. The underground working is accessed via a 17 degree incline shaft with an operating length of 105 m and serviced by a single drum winder. The winder operates at a speed of about 3.5 m/min hoisting two 1 t wagons from the bottom of the incline to surface for tipping (Figure 1)."

Jan 1, 2017

By K. Isaac, S. O. Bada

This research focuses on the co-firing of discard coal with refuse-derived fuel (RDF) to utilize this abundant resource in South Africa for energy generation and reduce the volume of waste disposed of at landfills. The potential of a coal with a high ash content (> 40%), which is a grade used in some power stations in South Africa, and its combustion compatibility with two different RDFs in terms of emission reductions has been established. Gaseous emissions and ash residues from the combustion and cocombustion of the coal, two different RDFs and coal/RDF blends of different proportion were analysed. One of the RDF samples contained mostly paper (PB) and the other mostly plastic (PL). Co-combustion ash from the discard coal and RDFs showed a decrease in chloride and alkali metal contents as the coal ratio in the blend increased. The slagging propensity of the co-fired blends was found to be very low, while the propensity for fouling decreased from high to medium for all the blends with < 75% RDF. Cocombustion of RDF with coal showed a decrease in SO2 emissions from 387 ppm (discard coal) to 50 ppm for the sample containing 25% coal discard plus 75% PL. A 15% PL to 85% coal blend also reduced NOx emissions from 145 ppm (100% PL) to 88 ppm. The lowest CO2 emission observed was 6000 ppm for the blend of 85% discard coal plus 15% PB. It was established that the most favourable fuel blend that can produce the lowest sulphur emissions if used for power generation is the 25% coal discard plus 75% PL sample.

Aug 2, 2022

By M. Hermanus, N. Coulson, N. Pillay

"SynopsisThis paper assesses the effectiveness of the Mine Occupational Health and Safety Leading Practice Adoption System (MOSH) and its potential to improve mine health and safety in South African mines. Developed by the Chamber of Mines, which represents the majority of the country&apos;s large scale mining employers, MOSH was devised to accelerate progress towards achieving health and safety milestones, which were set by tripartite agreement in 2003. The paper documents and builds on the findings of a study conducted by the Centre for Sustainability in Mining and Industry (CSMI) in 2011 that evaluated MOSH strategy, structures, and process of implementation.The study found that MOSH operated across the mining sector, was directed and dominated by experts and, despite best efforts to include other stakeholders, was led by employers. Statutory worker health and safety representatives and structures were not integrated into the complex change process developed by MOSH. The Mine Health and Safety Inspectorate (MHSI) and organized labour were ambivalent about direct involvement in MOSH and preferred regulatory measures to enforce the participation of mines. MOSH interventions were not targeted at mines with a poor health and safety record, and MOSH lacked a baseline from which to track impacts on sector-wide health and safety performance. The leading practices most widely adopted by mines were designed to improve, rather than fundamentally alter, existing practice. Although the depth of engagement with MOSH among stakeholders and on mine sites varied, mining companies, labour representatives, and the Mine Health and Safety Inspectorate (MHSI) saw the programme as significant.IntroductionIn 2011, the Chamber of Mines commissioned the Centre for Sustainability in Mining and Industry (CSMI) to evaluate the progress and effectiveness of the rollout of the Mine Occupational Health and Safety Leading Practice Adoption System (MOSH). CSMI, based in the School of Mining Engineering at the University of the Witwatersrand, is an independent research centre conducting health and safety research relevant to all major stakeholders in the mining sector. The purpose of the evaluation was to identify the factors that enabled or hampered the adoption of new technologies or practices. The timing of the evaluation, two years before the deadline for the 2013 safety and health milestones, allowed time for adjustments to be made. This paper summarizes the results of the evaluation and includes further analysis and discussion of the nature of the programme and the conditions that act to advance it or it hold back."

Jan 1, 2015

By S. Marx

More than twenty years ago Sasol, ISCOR, and some parastatals played a major role in ensuring that South Africa had sufficient technical skills. When the economy became tight and business and government were pressurized to decrease costs, the first budgets that were reduced were the training budgets. It seemed to be too expensive and too time-consuming to train apprentices. According to Stacey2, this is a major strategic issue facing the mining industry in South Africa. Two factors added to the shortage of skills challenge: ? Skills erosion and job losses ? Artisans ? currently the economy produces 5 000 but the need is 12 500 ? Level of mechanization in South Africa less than 10 per cent ? Average age of operators and artisans is 50 ? Greater awareness of occupational health effects of hand-held drilling. ? Workplace challenges ? The impact of HIV/AIDS and other employee wellness issues ? Changes and challenges in workplace environment i.e. the mining industry.

Jan 1, 2012

By L. S. Linda, P. G. H Pistorius

Ferritic stainless steel is utilized to fabricate automotive exhaust systems using a ferritic weld metal. Ductility of the weld metal is higher if its microstructure contains a significant proportion of equiaxed grains. The formation of equiaxed (rather than columnar) grains is favoured by a higher titanium weld metal content. In this study, the Ti content of ferritic stainless steel weld metal was changed by using Tifree (Type 436) and Ti-containing (441) ferritic stainless steel as base metals. The metal-cored welding consumable contained 0.4% Ti. Gas–tungsten arc welding and gas–metal arc welding processes were compared. The weld metal Ti content ranged from zero to 0.5% Ti, as determined from scanning electron microscopy supplemented by inductively coupled plasma optical emission spectroscopy. Cross-sections of the weld beads were subjected to point counting (to estimate the fraction of equiaxed grains) and image analysis (to estimate the average grain size). Point counting proved to be more reliable. The fraction of equiaxed grains was sensitive to the Ti content, but not to the welding process. Below 0.4% Ti, the fraction of equiaxed grains gradually increased with an increase in the weld metal Ti content; above 0.4% Ti, the fraction of equiaxed grains rapidly increased with increasing Ti content. The transition in behaviour at 0.4% Ti corresponded to a Ti content at which Ti-rich precipitates became stable at the estimated liquidus temperature of the weld metal.

Jul 2, 2022

By N. K. Singo, J. D. Kramers

The reprocessing of tailings resources to extract gold on an industrial scale has become common practice. While these projects are common in the Witwatersrand basin, similar low-technology processes are not operational in smaller goldfields. This study explores the possibility of reclaiming the tailings dump of the Louis Moore Mine in the Giyani Greenstone Belt, investigates potential hazards to communities in the vicinity, and identifies mitigation strategies. Auger samples were taken from the Louis Moore tailings at depths of up to 5 m. Aqua regia leach analyses show Au concentrations of up to 1 g/t. Inferred estimations based on ordinary kriging (OK) and inverse distance weighted (IDW) methods put the residual Au resource in the Louis Moore tailings dump at 0.20 t. Reworking the tailings is viable, although a potential environmental risk exists in the form of elevated arsenic concentrations. Further exploration is required to determine the mineralogical associations of Au and As. Tailings reworking would assist in raising funds for mine rehabilitation. The secondary tailings could potentially be repurposed, which would provide employment and facilitate community development, as well as deliver environmental benefits.

Jul 1, 2021

By Z. Ruetz

Portable X-ray fluorescence (pXRF) analysis has been widely adopted in the geochemical and environmental field as a cost-saving alternative to standard analyses. This paper outlines the efficacy of a method for indirectly quantifying organic copper content in solvent extraction circuits via stripping of the chelated metal with concentrated sulfuric acid in a single contact and subsequent pXRF aqueous analysis. pXRF analysis is common within the mining industry but presents unique challenges with liquid analysis, the most prevalent of which are briefly discussed. This method was developed specifically for mining operations with regional constraints and limited resources. Providing an in-field alternative to flame atomic absorption spectrophotometry and inductively coupled plasma optical emission spectroscopy, this entirely mobile XRF analysis method produces consistent and accurate results within minutes and at a fraction of the cost.

Jan 1, 2023

By H. Dudycz, A. Skoczylas, P. Stefaniak, P. Pyda

In the era of Industry 4.0, technologies such as Big Data (BD) and the Internet of Things (IoT) play a key role, especially for multi-site manufacturing companies. In such companies, the challenge is to collect and process massive amounts of data from industrial devices and extract key information from this data in real-time for ad hoc decision-making. The ability to analyse data from industrial devices translates directly into streamlined production processes, cost optimisation, prevention of unplanned events, and safety during operation. In this context, particular attention should be paid to Big Data Analytics (BDA), whose main source is the Industrial Internet of Things (IIoT). The purpose of this paper is to propose an IT system architecture incorporating BD and the IoT for a mining company. The paper presents results from a literature review focusing on available BD and the IoT solutions for industry (mining in particular) for the purposes of the acquisition, integration, and advanced analysis of data. The advantages and disadvantages of the different solutions were indicated and gaps in the accessibility to dedicated functionality are identified. Based on the analysis of a multi-site mining company, the main challenges faced by such companies planning to implement BD and IoT solutions are identified. Also, a proposal for an IT system architecture incorporating BD and IoT for a mining company is described in the paper. The contribution of the article consists of the identification of the challenges faced by mining companies planning to implement BD and the IoT solutions, and the proposal of an IT system architecture that allows BDA whose main source is the IIoT.

Sep 1, 2021

By S. Lohmeier, D. Gallhofer, B. G. Lottermoser

Reprocessing of historic gold tailings is a common activity in South Africa, while base metal tailings offer similar reprocessing potential. The historic base metal tailings of the Namib Pb–Zn mine (Erongo Region, Namibia) still contain valuable resources of Pb and Zn in carbonate-rich matter. Micro-analysis of primary ore minerals identifies some galena as argentiferous and sphalerite as the principal host of Cd. This study demonstrates that knowledge of primary ore mineralogy helps to reveal the hosts of valuable commodities (Ag, Cd) and that field-portable X-ray fluorescence tools allow precise and accurate determinations of major and minor elements like Zn and Cd in such carbonate-rich material. Although there are limitations to directly determine the contents of certain element (i.e., As, Sb, In), linear correlations allow prediction of the likely abundance of these elements. Providing that the inter-mineral and inter-element relations are understood and there is consistency in sampling and analytical methodology, portable X-ray fluorescence analysis is an effective method to evaluate the chemical characteristics of base metal tailings for a range of major and trace elements.

Sep 9, 2024

By Stuart Marsland

"Reference materials have always been important for validating and controlling analytical methods&apos;, They have recently become even more important as quality requirements have become more stringent and customer demands for properly verified and controlled results increase. Clients, especially from the resource exploration industry demand critical validation of all results reported. Mintek has been producing geological and semi processed ore references since the early 1970&apos;s and recently due to increase in demand other manufactures have entered the South African Market.This paper describes Analytical challenges from the customer&apos;s perspective. The customer being the metallurgist, mine geologist, environmental scientist and geologists from resource companies. Reference Materials and their appropriate use and good understanding of them can aid greatly in building confidence in the results, choosing the right Laboratory for a project, deciding which set of results arc correct and providing evidence to the customer&apos;s clients that the results obtained are the very best possible.Throughout the world there are hundreds of reference materials produced by over 80 organisations and these are mainly ores, rocks, semi processed ores, metals, and many more. Mintek is one of the top 10 producers with over 75 products. Many of these producers including Mintek and their respective standards organisations belong to the ISO REMCO committee and their respective work groups. This committee&apos;s main task is to draw up guide lines for the use, manufacturing and certifying reference materials. In South Africa a mirror committee has recently had its inaugural meeting the function is to give clear mandate to the South African representative on the main ISO REMCO committee, the South African delegate bas an opportunity to influence the contents of the guides.Tile SARM program has since the year 2000 increased its sale three fold, the question is why? There is more accountability needed in our world. That means Analytical results have to be the very best possible and risks associated to them must be well quantified. Consider that the risk of wrong results of wrong decisions made from a result is trivial to laboratory, in comparison to the laboratories customers. The consequence to a laboratory could be a loss of income or some one may lose their job. To the customer he may dig up 1000 of ton&apos;s of rock with nothing in it or worse still don&apos;t mine it when the grade is high enough. This is seriol1s money."

Jan 1, 2014

By J. Hadjigeorgiou, T. R. Stacey

This paper introduces the Quantified Value-created Process (QVP), a decision-making process for use in mine design and operation. The implementation of the QVP is founded on a ten-step rock engineering design process and a ten-step strategic planning process. The potential of this approach is demonstrated by examples of value created as a result of good research, design, and planning. The QVP is divided into two parts, namely, a ‘planning the process’ section and an ‘implementing the process’ section, and can be considered to be an extension of the risk approach. All costs, direct and indirect, associated with a significant mining decision (design, operational, investment) must be quantified in advance of committing to that decision, to determine the value that will be created in the short, medium, and long terms. Ethical values, associated with health, safety, the environment, public perception, and social aspects, may be difficult to quantify in economic terms, but must nevertheless also be considered. In contrast with a traditional risk approach, the QVP will identify the upside, and allow executives to make more informed strategic decisions. In this context it is essential to actively engage upper management in the decision process.

Feb 2, 2022

By I. Cameron, S. Ramjee, A. M. Garbers-Craig

The cause of reduced workability and increased ageing of a blast furnace taphole clay was examined. The investigated taphole clay contained 60 mass% alumina, with phenol-formaldehyde resole resin and liquid pitch serving as the binder system. The workability and Marshall extrusion pressure of the as-manufactured clay samples were evaluated to assess the extent of ageing of the clay. The wettability of all the raw materials was investigated to confirm compatibility between the dry raw materials and both the resin and liquid pitch, while the dry raw materials were analysed using XRF, XRD, and SEM-EDS. The characterisation of the resin and liquid pitch, as well as an analysis of their interaction, was performed using viscosity measurements, Fouriertransform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The analyses confirmed a chemical interaction between the resole resin and liquid pitch, where the chemical structure of the resole resin changed when mixed with pitch, preventing the typical curing behaviour of the resin. Upon ageing of the resin-pitch mixtures, the resin underwent premature cross-linking, causing the curing process to initiate at lower temperatures, i.e., earlier onset of curing. This premature cross-linking was likely due to secondary amines present in the liquid pitch, which acted as a catalyst for the curing process of the resin. This reduction in curing temperature after ageing was confirmed by an increase in binder viscosity, which was identified as the primary cause of reduced workability, accelerated ageing, and increased Marshall extrusion pressure of the taphole clay.

Jul 23, 2025

By C. Chapman, M. G. Reading, M. P. Amsden

Ecstall Mining Limited, a subsidiary of Texas Gulf Sulphur Company, operates the Kidd Creek Mine, a 10000 tons per day base metal producer, near Timmins, Ontario. Two different types of ore are mined and milled: copper-zinc and silver-lead-zinc. At the highly automated Ecstall concentrator the ores are processed by selective flotation in three individual circuits. One of the most important metallurgical tools for process control is a sample system incorporating continuous on-stream X-ray analysis. Recently this system was automated further by the addition of computer control of reagents for two copper-zinc flotation circuits. The computer programs, utilizing optimum seeking methods and smelter contract terms, have increased copper recovery by 1.1 per cent, zinc recovery by 1.4 per cent, and have reduced reagent costs by 16 per cent. Although not expected, copper and zinc concentrate grades were improved slightly as well.

Jan 1, 2014

By T. Bruce, R. C. A. Minnitt

Mining operations are generally reluctant to install high-cost sampling systems at operations that have been functioning for many years. The principal objection to installing appropriate equipment to extract correct and representative samples in process flows is the time and costs involved. The Theory of Sampling (TOS) provides a structured framework for identifying and quantifying the errors and bias associated with any sampling event, but this may be insufficient to initiate substantial investment in correctly designed sampling equipment. Financial losses arising from substandard sampling installations are usually disregarded because the value-add from a good quality sampling solution is invisible, but the cost is quite obvious. Depending on the needs, a less-than-perfect or fit-for-purpose sampling solution may be acceptable, provided the magnitude of sampling errors is understood and the assay results are interpreted accordingly. Categorical levels of acceptable accuracy and precision can be established depending on the sampling position in the mining value chain and the nature of the decisions to be made. The objective benefits of proposed fit-for-purpose sampling solutions should be presented to relevant decision-makers in such a way that adverse subjective decisions are countered so that appropriate solutions are implemented. Practical examples of the benefits from motivating the implementation of fit for purpose sampling solutions at sampling facilities around the world are provided.

Jul 2, 2022

By A. C. Johnstone

The aim of the study is to determine if pit lakes are a sustainable coal mine closure option in South African. The water balance, chemistry, limnology, and bacterial population of three selected pit lakes were investigated. The lakes are in the three major coal basins of South Africa and are associated with different lithologies and mining methods. The major factors driving the water balance of the pit lakes are direct rainfall, runoff, inflow from old mine workings, and groundwater infiltration, with the major losses being evaporation or discharge onto surface. The study indicated that pit lakes can be designed as ’terminal sinks’ to provide a sustainable mine closure option. The pit lakes sampled have an alkaline pH, and mostly a sodium/calcium sulphate water with total dissolved solids content of less than 3000 mg/l. The phytoplankton and microbiological data indicates that the pit lakes support aquatic life. The study shows that correctly designed pit lakes can be an environmentally sustainable closure option for South Africa’s coal mines. A suggested design manual has been developed to assist mine owners and regulators in developing sustainable coal mine pit lakes as a closure option.

Oct 1, 2021

By J. F. Brand, J. C. van Dyk, F. B. Waanders

"Syngas from Africary’s Theunissen underground coal gasification (UCG) project will be used for power production and synthesis of liquid fuels and commodity chemicals. However, some of the coal components, especially condensable water, oils, tars, inorganic trace elements, and a small fraction of fly ash and particulate matter, make their way to the surface via the production well and can cause adverse impacts on downstream processes. Africary’s standard design incorporates a cold gas clean-up system that relies on relatively mature techniques based on highly effective wet scrubbers and acid gas removal (AGR) systems such as Rectisol®, but with the downside of low energy efficiency and waste water generation. In this paper, novel technologies for removing contaminants and species separation from the hot (T > 300°C) raw syngas are compared. Comparisons are made between supersonic gas separation (SGS), Ranque–Hilsch vortex tube (RHVT), vortex gradient separation (VGS), and inertia vacuum filtering (IVF), and a vortex-based gas separation concept is proposed for UCG applications. IntroductionImpurities in gasification feedstock (coal, biomass, waste, etc.), especially sulphur, nitrogen, chlorine, and inorganic mineral matter, often end up in the syngas and can cause adverse impacts on downstream processes. Africary’s standard design incorporates a cold gas clean-up system that relies on relatively mature techniques based on highly effective wet scrubbers and acid gas removal (AGR) systems such as RectisolR, SelexolR or aMDEAR; but with the downside of low energy efficiency and waste water generation.Hot (T > 300°C) gas clean-up technologies are attractive because they avoid cooling and reheating of the syngas stream. Some available warm gas cleaning technologies include traditional particulate removal devices such as cyclones, candle filters, membranes, and molecular sieves. The warm gas desulphurization process technology developed by RTI LLC (2018) requires hot syngas to remove sulphur and has become commercially ready. Many other hot gas cleanup systems are still under development, given the technical difficulties caused by extreme environmental and operating conditions."

Jan 1, 2018