Search Documents

By D. P. Roberts

This paper reviews the use of crush pillars on mines in the Bushveld Complex and the Witwatersrand Supergroup. Stress measurements were undertaken in order to determine the residual strength of these crush pillars. The results from these stress measurements are compared with previous attempts to determine the residual strength of crush pillars using back analysis. It is concluded that the residual strength of such crush pillars lies in a band between 13 MPa and 25MPa. Using the data from the stress measurements, as well as published and unpublished data, a stress-strain curve for a crush pillar with a width-to-height ratio of 2:1 is proposed. Where further work is required, this is indicated in the text.

Jan 1, 2005

By D. P. Roberts

The stoping of platinum orebodies in the Bushveld has in the past been accomplished by using in-stope pillars to ensure stability of the workings. In the future, the use of continuous mining machines to mine the platinum orebodies is probable. It is not envisaged that such machines will cut in-stope pillars. This paper describes the alternative support systems that will replace the pillars and the stope geometries that will be required for this type of mining. The paper describes how the support resistance provided by in-stope pillars in current mining was determined and then evaluates support systems that can substitute for these pillars. Conceptual layouts based on existing breast mining layouts are presented. The layouts consist of panels of up to 100 m face length between rigid strike stabilizing pillars. A number of design charts are then proposed that allow for the design of appropriate support systems.

Jan 1, 2005

By M. Solomon

During the course of 2011 the nationalization of mines emerged as one of the most contentious and emotive political issues under review. Some four years after the African National Congress electoral conference held in Polokwane, which had led to a change of leadership within the country's ruling party, elements within the ruling party's youth league, which had been virulently supportive of the change in leadership, turned on the incumbent President, using the mining question as its rallying call. At issue was the expressed perception that mining has, since the country's democratization, not delivered the anticipated benefits to the population as a whole, continues to be the preserve of the capitalist element of the South African community, and is therefore in need of radical reform. Aspersions were made that transformation within the industry had failed dismally and that mining companies had not delivered against their commitments to the Mining Charter and social and labour plans. The debate became extremely vocal and heated, evoked dramatic and emotive opinions, and vigorous skirmishes on the matter were fought in the media over much of 2011 and into 2012.

Jan 1, 2013

One of the seminal pioneering papers in reserve evaluation was published by Danie Krige in 1951. In that paper he introduced the concept of regression techniques in providing better estimates for stope grades and correcting for what later became known as the ‘conditional bias’. In South Africa, the development of this approach led to the phenomenon being dubbed the ‘regression effect’, and regression techniques ultimately formed the basis of simple kriging in Krige’s later papers. In the late 1950s and early 1960s, Georges Matheron (1965) formulated the general theory of ‘regionalized variables’ and included copious discussion on what he termed the ‘volume-variance’ effect. Matheron defined mathematically the reason for, and quantification of, the difference in variability between estimated values and the actual unknown values. In 1983, this author published a paper that combined these two philosophies so that the ‘regression effect’ could be quantified before actual mining block values were available. In 1996 and in some earlier presentations, Krige revisited the regression effect in terms of the conditional bias and suggested two measures that might enable a practitioner of geostatistics to assess the ‘efficiency’ of the kriging estimator in any particular case. In this article, we revisit the trail from ‘regression effect’ to ‘kriging efficiency’ in conceptual terms and endeavour to explain exactly what is measured by these parameters and how to use (or abuse) them in practical cases.

Jan 1, 2015

By M. Dworzanowski

Beneficiation, in the context of this paper, has two distinct definitions. From an economic perspective, beneficiation relates to adding value to a mined raw material. From a metallurgy perspective, beneficiation relates to processes used to upgrade the mined raw material. Clearly then, ?economic beneficiation? is dependent on ?metallurgical beneficiation?. South Africa possesses the world?s largest mineral resources by value and is a significant global producer of many mined commodities. Significant metallurgical beneficiation of ores does occur in South Africa. The role of metallurgy in economic beneficiation will be examined in terms of current practice and the potential for expansion. South Africa?s main mining commodities will be covered ? namely gold, platinum, coal, iron ore, manganese, chromium, vanadium, copper, nickel, titanium, zirconium, uranium, and diamonds.

Sep 1, 2013

By J. E. Nesset

The bubble size, together with the gas rate, determines the bubble surface area flux in flotation machines and, therefore, impacts directly on the kinetics of flotation. Understanding the variables that influence bubble size is one of the keys to understanding flotation recovery. Surprisingly, these relationships are poorly understood, largely due to the difficulties associated with gas dispersion measurements in industrial environments. The McGill gas dispersion sensors (bubble size, gas rate, gas holdup) are capable of reliably making such measurements. This paper reports on a study, using the McGill sensors in a 0.8 m3 Metso RCSTM pilot cell, which investigated the effect on bubble size of frother type and concentration, gas rate, temperature and rotor speed. A Denver laboratory cell was used to investigate the effect of elevation above sea level. Frother concentration proved to have the predominant influence on bubble size, and the effect of frother type can be normalised as a function of the critical coalescence concentration (CCC). Measurements made at many plant sites worldwide are compared to the model developed using the Metso RCSTM unit.

Jan 1, 2007

By F. M. C. C. Vieira

There are many uncertainties that a mine designer should consider when selecting an optimal layout. Even though the inherent variability in the design parameters indicates that single-values are not representative of mining conditions, risk estimators such as ERR are often used without considering their statistical distributions. A probabilistic methodology has been developed to assess the influence of the extraction sequence and layout geometry on the rockburst risk associated with four ultra-deep mining layouts. The statistical distributions of incremental energy release rates and excess shear stresses at face elements are used as indirect estimators of rockburst risk in stopes, and the statistical distribution of the rock condition factor (RCF) is used as an indirect estimator of rockburst risk in tunnels and service excavations.

Jan 1, 2002

By B. G. Russell

A wide range of minerals is found within the Republic of South Africa, many of which are exploited to a greater extent than in similar deposits found elsewhere. It is often asked whether this is atributed to the high grade of the ores encountered in this country, or whether such factors as fiscal and Infrastructural incentives create an economic climate that has en bled the mining industry to successfully extract and market minerals at a profit. This paper views South Africa's mineral resources in a regional and global context In an attempt to place the country's geological wealth in perspective. It represents the author's own Views, and not necessarily those of the Department of Mine al and Energy Affairs.

Jan 1, 1986

By A. F. Lee

A pick-up apparatus capable of yielding quantitative results has been described. Studies of some collector-mineral systems have been presented to illustrate the versatility of the apparatus and prove the validity of results.

By T D. Sullivan

Risk lies at the heart of all mining and nowhere more so than in pit slope design. Mining is principally about two areas of risk; safety and economics. This paper addresses the main elements of pit slope design and presents a view of the state of the art in terms of safety, design, prediction of performance, success and pit slope management. There has been a recent trend for serious injury and fatalities due to stability in open pit mines. The causes and contributing factors are analysed in relation to geotechnical knowledge, pit slope design and management. Currently there is no standard classification system for mine slope designs and it is considered doubtful if a universal system is possible. Designs are usually formulated in accordance with many different methodologies, various engineering principals and a number of different philosophical approaches, with results often presented in terms of Factors of Safety or Probabilities of Failure. However wide experience has demonstrated that even with apparently detailed engineering investigation and analysis at Feasibility Level, at the Operating Stage mine slope angles are regularly subject to large changes. The general experience is that these changes are ± 5° and 16° overall, which is considerably outside the accepted order of accuracy. For large deep mines these are huge changes and represent significant risks to the operations. The current state of practice in pit slope design is examined for two stages, feasibility and operating.

Jan 1, 2006

By Mark Van Kleek

CONTENTS ?The Falcon C ?Data from a Production Trial ?Methodology ?Scale-up ?Test Results ?Circuit Configurations ?Conclusion

Jan 1, 2006

By M. Yavuz, M. Aksoy, G. Once, M. Iphar

This paper is concerned with a study on the floor heaving in the transport road of the GLI Omerler Colliery in Tuncbilek-Turkey. This gallery has been opened at the depth of 200 m through the formation of marl in 4.6 m width and 3.5 m height in cross section. Floor heaving occurred up to 70 cm in height in maximum and caused severe problems in railway and band-conveyor transportation in the main road. In addition; after the current panel mined out, the shield support units could not be transferred to the new panel because of the deformation of roadway cross-section. The I-profile steel arch supports also sank into the weak floor rock. This situation has been studied by numerical analysis using the FLAC3Dfinite difference program in order to investigate the rock mass behaviour around the opening. The obtained outputs of the numerical model have showed consistency with the amount of floor heaving in the gallery at 200 m depth. A new gallery has been driven at the depth of 115 m and M4 longwall panel has just been taken to production. So as not to encounter with the same problems at 200 m depth, especially longwall face moving problem, various numerical models have been studied in order to keep the floor heaving in the acceptable limits required to move shield support units. Keywords: Floor heave, Numerical modelling, FLAC3D, Failure criteria, RocLab

Jan 1, 2003

By I. K. Craig, F. R. Camisani-Calzolari

Defects which occur at the surface of a continuously cast slab impede the throughput of final product, because an extra stage in the process is required to grind the defects away before further processing can take place. Defect prediction and the minimization of the occurrence of defects is required. The use of two models to define the defect propagation is explained. Both models are derived using system identification techniques such as auto-regression with exogenous input(ARX). One model is used to determine the effect of manipulated variables such as casting speed and measured disturbances such as mould level on temperatures within the mould. The other isused to determine or indicate the effect of the mould temperatures on the occurrence of defects such as transversal cracks. The latter model can be used to predict when the defects will occur and the former can be used to control the occurrence of the defects. Keywords: continuous casting, surface defect, control system, predictor, system identification, ARX

Jan 1, 2003

By G. M. J. van Heerden

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The Union Section of Anglo Platinum is situated ±18 km west of the town of Northam on the north-western rim of the Bushveld Igneous Complex. Both the Merensky and UG2 reefs are mined. Support of the Merensky stoping areas with rock bolts is specifically problematic due to the stoping width restrictions varying around 90 cm. The installation equipment of in-stope rock bolts and the effectiveness thereof in the Merensky stoping areas was critically evaluated. In order to do this a background research on the need for better on-the-face support had to be conducted. The need for improving the rock bolt drilling and the equipment had to be investigated and the financial implications and justifications for the improved equipment examined. To conduct the search an overall study was done on the rockfalls and safety aspects throughout the platinum industry in South Africa and specifically Union Section. It was found that most of the rock falls in the Merensky stoping areas of which ± 70% are less than 1.2 m in thickness generally occurs within 4 m from the face and causes ± 60% of the in-stope injuries. Serious shortcomings had been identified with respect to the airleg, rock drill machine and the drill steels used in the drilling of the rock bolt holes. Through experimentation, using a testing frame built for this purpose on surface and with the co-operation of mine staff and suppliers, a number of possible modifications were identified and tested. This resulted in the final product with which it was possible to drill a 1.2 m hole in the hangingwall of the stopes ranging with an angle to the hanging from 90° for a 90 cm stoping width and 67° for a 80 cm stoping width. It is confidently concluded that this system will effectively improve the total face support and result in a substantial reduction of rock falls and consequently the occurrence of injuries and fatalities in the Merensky stoping areas. The installation of rock bolts on the face with the modified drilling equipment will increase the direct support, but the system has a potential of a substantial reduction in the profile stick support density and an increase in productivity in the stoping areas due to fewer occurrences of rock falls. It was finally concluded that effective modifications to the drilling equipment for rock bolt in-hole drilling could be made and the installation thereof in the stope face is adequately justified.

Jan 1, 2002

By G. L. Smith

This paper consolidates the key elements of seven contributions, on strategic long-term planning, to two of the three international conferences on Strategic versus Tactical approaches in Mining held over the period 2005?2008. The holistic concept of strategic long-term planning as developed and implemented at Anglo Platinum is described. Consideration is given to the planning cycle, principles supporting the construction of the long-term plan, and aspects of unique best practice as developed in Anglo Platinum. Further description of Anglo Platinum?s approach to corporate governance, including the processes, methodology, systems, unique tools and techniques that are applied to value and select capital investment options is also given.

Jan 1, 2009

By S. G. Hardcastle, C. K. Kocsis

In Canada’s metal mines, ventilation, which requires electricity to operate the fans and fossil fuel for heating, accounts for a significant portion of the overall mine’s underground power consumption. Mine ventilation systems are usually designed near the end of the mine design process and often designed for the ‘worst-case-scenario’ with respect to ventilation demand. In Canada’s metal mines this is commonly dictated by either diesel equipment usage or heat management considerations. Once designed, mine ventilation systems tend to operate at this peak level throughout the operating life of the mine. This is despite there being significant periods when this quantity is not required this is done mainly due to lack of appropriate ventilation controls. Consequently, such systems are inefficient and wasteful and this must be changed if mining operations are to remain competitive while meeting increasingly more stringent regulations of underground environmental conditions. The advances in computing power and modelling software now make it possible to design, model and schedule a mine from opening to closure. The tools used for this include several disparate types of software. A developing trend is to design and plan the mine using orebody modelling software, followed by using discrete event simulation to predict production and evaluate various operating scenarios. It seems that again ventilation design is not being integrated into this process. Although, several modelling packages exist for ventilation design, little work has been done on integrating ventilation modelling into the overall life cycle plan of the mine. This paper will present a discussion of the work where the authors are attempting to integrate discrete event simulation for mine planning with ventilation modelling to predict the ventilation requirements for the operating life of the mine.

Jan 1, 2003

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-technological cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

By A. Wedepohl

Selective leaching of phases in charge chrome is used in a variety of industrial processes for the production of chromium chemicals. A mineralogical study was made of a range of local charge chrome samples, at various stages of leaching in sulphuric acid (20g/l at 90°C), using mainly a scanning electron microscope (SEM) together with an energy-dispersive spectroscopy analyzer (EDS), and X-ray diffraction techniques. It was found that the leaching behaviour of the different types of charge chrome depends largely on the nature of the secondary phases, which in turn depends upon whether the silicon content is above or below 4 per cent by mass. The leaching behaviour of high-chromium ferrite is anomalous, and it is postulated that the process is analogous to the corrosion of brass by dezincification. Keywords: charge chrome leaching, scanning electron microscope

Jan 1, 2000

By J. H. Zietsman, M. W. Erwee, Q. G. Reynolds

Pyrometallurgical furnaces, essential for metal extraction, operate at temperatures exceeding 1600°C and represent complex multiphase systems that challenge direct industrial research. Multiphysics models play a key role in shedding light on their intricate behaviours, supporting the refinement of design and operational strategies. Integral to the operation are the tap-holes, which facilitate the removal of molten products and are routinely opened by lancing, a process comparable to the use of a cutting torch, where high temperatures result from oxygen reacting with an iron lance. When the lance pierces the clay, oxygen gas enters the furnace, which could influence the behaviour of the molten material inside. In this work, a multiphase fluid flow model was used to investigate bulk flow dynamics, with a focus on the effects of the lancing process on the inside of the furnace, immediately behind the tap-hole. Incompressible and compressible multiphase fluid solvers were used and compared with respect their performance – the intention was to assess whether using a compressible solver would yield a different solution to the incompressible one. It was concluded that there are negligible disparities in bulk fluid flow behaviour between the solvers for the case studies examined, indicating that solver selection might be less consequential for certain aspects of oxygen lancing.

Apr 16, 2024

By E. Van Der Lingen

This paper provides a review on coloured gold, platinum, andpalladium intermetallic compounds, and discusses the models thatwere developed to obtain these materials. These compounds have acrystal structure of high symmetry, such as the CaF2or CsClstructures, ensuring distinct electron band structures. Variousexamples of coloured gold, platinum, and palladium intermetalliccompounds are provided. More in-depth discussion is provided on thepurple gold (AuAl2) and yellow platinum-aluminium (PtAl2)compounds with CaF2structure, as well as the purplish-pinkpalladium-indium (PdIn) compound with CsCl structure. Precious metal intermetallic compounds are used in jewellery andprovide a new dimension to design. Some of these compounds havealso found use as barrier coatings on turbine blades for jet engines,and more recently, research has been conducted into their potentialuse as catalysts, electro-catalysts, sensors, capacitors, and fordecorative coatings.

Jan 1, 2014