Search Documents

By F. Dinter, S. A. C. Hockaday, Q. G. Reynolds

The thermal decomposition of carbonate minerals as pre-treatment before smelting reduces the energy requirement for smelting. It can also make the combustion of fossil fuels for heating unnecassary. Thermal decomposition may become important in reducing greenhouse gas emissions when producing ferromanganese alloys while simultaneously reducing electrical energy demand during smelting. A kinetic reaction rate model for the thermal decomposition of manganese ores is presented, based on published reaction rate kinetics for the decomposition of manganese oxides and calcium carbonate. The model was validated against thermogravimetric data for two carbonaceous manganese ore samples and one ferruginous manganese ore sample. The reaction rate model shows that carbonate minerals in the manganese ores are decomposed at temperatures above 900 °C while pyrolusite is decomposed at temperatures from 450 °C to 500 °C. Mn2O3 decomposes rapidly at 550 °C. Braunite decomposition at temperatures below 1000 °C was negligible. The presence of organic carbon in the samples led to further reduction of the samples during thermal treatment.

Aug 3, 2023

By J. Petersen, K. Shaik1, H. Kolev, Z. Cherkezova-Zheleva

Sperrylite is one of the most abundant platinum minerals globally, valued for its economic importance but also known for its highly refractory nature, making it difficult to process via the conventional route. This study explores the oxidative leaching of sperrylite using a cyanide–ferricyanide system, with a key focus on characterisation of the mineral and surface speciation under varied leaching conditions using x-ray photoelectron spectroscopy. The parameters investigated include the effect of sodium cyanide concentration, the use of potassium ferricyanide as an oxidant, copper sulphate pentahydrate as a catalyst, as well as the effects of temperature and particle size. A limited set of leaching tests was carried out to study the surface chemistry rather than optimising dissolution conditions. This approach identified mineral oxidation states and shifts in binding energies, prior to and post leaching. XPS analysis of sperrylite’s surface chemistry identified key species, comprising the bulk Pt(II)–As (≈73 eV) and As(–I)–Pt (≈41.8 eV) states, together with surface oxidation products Pt(II)–O (≈72 eV), Pt(IV)–O (≈74.5 eV), As(III)–O (≈43 eV) and As(V)–O (44.5 eV). Leaching led to the removal of pre-existing oxides on the ultra-finely ground sample, exposing the underlying bulk species. In contrast, the crystalline sample with an initial low concentration of oxides, generated higher amounts of fully oxidised species after leaching, reflecting greater surface reactivity.

Mar 6, 2026

By E. P. Preis, R. C. W. Webber-Youngman

The real cost of any mining incident has, empirically, proven to be estimation-driven, rather than factdriven. One of the main reasons for this lies with the complexity of the cost composition of any given mining incident. Incident costs comprise both direct and indirect cost factors, and in many cases the costs associated with these factors are incurred during different time periods following the incident. In this paper we aim to identify the various cost factors arising from mining incidents, provide a thorough understanding of all the potential cost factors identified, and draw general conclusions on the knowledge obtained. Furthermore, recommendations are made on how mining companies could use the results, in order to assist them in calculating the costs of mining incidents. The paper also provides suggestions for further research, with the emphasis on the most significant immeasurable cost factors, namely the costs of implementing job accommodations following an incident, the harm to company reputation, and the decreased productivity due to low worker morale/psychological factors following an incident. If mining companies are aware of and understand which factors could contribute to the cost of any given incident, future planning and incident cost estimations could be easier. It should, however, be noted that although this study provides a comprehensive list of cost factors (and detailed explanations), other unknown cost factors relating to mine incidents could prevail in extreme cases.

Jan 1, 2021

COUNCIL The following served on Council during the year under review: Office bearers: Prof D. D. Howat (President), Dr J. P. Hugo and P. W. J. van Rensburg (Vice-Presidents), V. C. Robinson (Immediate Past President) and D. G. Maxwell (Honorary Treasurer). Ordinary Members of Council: H. P. Carlisle, R. C. Espley-Jones, G. H. Grange, Dr D. I. Legge, W. W. Malan, Prof R. P. Plewman, Dr R. E. Robinson, Dr M. D. G. Salamon, L. W. P. van den Bosch and P. A. von Wielligh. Branch Chairmen: A. Bain (Witbank-Middelburg Branch), J. M. Meyer (O.F.S. Branch). Past Presidents serving on Council: R. J. Adamson, M. Barcza, H. Britten, H. E. Cross, J. K. E. Douglas, R. C. J. Goode, P. Lambooy, Prof J. de V. Lambrechts, Dr J. T. McIntyre, J. F. Reid and H. Simon (until March 1972). Ten Council meetings were held during the year with an average attendance of nineteen, and the standing committees held 27 meetings. FINANCE The annual accounts which are attached to this report show an excess of income over expenditure of R21 519. It is very gratifying to be able to report that Council's efforts to stop the depletion of our accumulated funds are meeting with success. The most important contributors to our surplus this year are symposia and colloquia, sales of publications, Company Affiliate subscriptions and the profit on the journal. While we do not expect continued profits from all these sources in the future we do feel that we are now in the process of accumulating a substantial financial foundation. This will give the Council the necessary confidence to initiate the new developments in the activities of the Institute which are now under consideration. The decision to create a new grade of membership, Company Affiliate, is dealt with elsewhere in this report. There has been a generous initial response from companies and this is the cornerstone of our improved financial expectations. The MacArthur Forrest Memorial Fund shows an excess of income over expenditure of R91 and the total fund was, therefore, increased by this amount to R4 502. The balance sheet shows that the market value of quoted shares and debentures increased during the year from R9 160 to RH 331, which is R2 134 in excess of the book value. Accumulated funds now amount to RH 529 compared with R23 010 a year ago. MEMBERSHIP Sixteen Fellows, twenty Members, six Graduates, nine Associates, twelve Students and twenty-four Company Affiliates were elected during the year. One Member and two Associates were reinstated. Twelve members were admitted to retired membership. Transfers: Member to Fellow, three. Graduate to Member, seven Associate to Fellow, one. Student to Member, one. Student to Graduate, four. Student to Fellow, one. Your Council records with deep regret the death during the year of the following: Dr A. J. Orenstein (Honorary Life Fellow), R. A. Cooper, R. J. Spargo, H. Simon and F. Meyer (Life Fellows), S. D. Loxton, W. P. Arnold, G. C. Needham, W. G. Pyne-Mercier, J. Innes and O. T. Wright (Fellows), E. P. Mennell and O. B. Prentis (Members), J. Brits (Associate). After careful consideration of all the implications it was decided during the year to create a new grade of membership to be known as Company Affiliate, in order that there might be a formal and permanent channel for companies to contribute to the important work of the Institute. As recorded above, 24 companies had joined by the end of the year and many further applications have been received since. We extend a hearty welcome to all our new members. A comparative statement of membership as at 30th June, 1972, and the end of the previous year is shown in the following tabulation:-

By Y. Rao, Y. Huang, G. Wang, W. Liu

The properties and deterioration in strength of cemented tailings backfill (CTB )in the underground acidic environment under oxidizing conditions were studied. X-ray diffraction analysis and scanning electron microscopy of the surface of the CTB was carried out, and the sulphuric acid corrosion mechanism elucidated. The properties tested included compressive strength, elastic modulus, cohesion, internal friction angle, variation in the hydrogen ion concentration, and stress-strain relationship in different corrosion periods. The damage model of the CTB was established considering the effects of parameters such as corrosion time and strain on the damage evolution. It was found that the compressive strength, elastic modulus, cohesion (binder effect), and internal friction angle increased at first and then decreased with exposure time. In the long term, the peak stress decreased with corrosion time while the peak strain increased; elastic modulus, and deformation modulus also decreased. The damage caused by corrosion and by load were related by means of a mathematical model, which revealed the relationships between sulphuric attack, load, and damage to backfill in complex underground environments. During corrosion, the expansion of gypsum and ettringite caused microfractures in the CTB. With increasing corrosion time, micro-cracks developed and proliferated. The mechanism of corrosion damage was found to be the dissolution of hydrogen ions and a sulphate ion reaction that produces an expansive substance, resulting in deterioration of the strength of CTB.

Jun 1, 2021

By M. Grozdanovic, D. Marjanovic, M. Ilic

We present a framework for solving the problem of functional compatibility between process control equipment in control centres at underground mines and operator capabilities. The equipment incorporates displays of current ventilation, gas, and fire hazard data, status of alarm and early warning systems, a voice communication subsystem, and facilities for recording and printing ofdata and reports. The layout of the existing control panel is compared with a recommended design. The basic principles of ergonomic design and arrangement of the controls and indicators, as well as ease of use, type of operations carried out with these controls, and operators’ viewing angles are discussed. The objective is to improve the usability of control panels, display boards, and graphic screens so as to enhance the functioning of control centres and optimize control of technological processes in coal mines.

Jun 10, 2024

By D. N. Golenkov, N. I. Lomaka, A. V. Kozub, T. V. Ignatova, E. V. Shelepov, D. O. Sharkovskiy, A. V. Chanturiya, R. I. Ismagilov

The modern Russian iron ore mining industry is faced with multiple challenges from everincreasing requirements of steel-making, the value of iron ore concentrates, depletion of high-grade ore reserves and complications of the mining and geologic environment’s necessity to process low-grade ores with complex material composition and low valuable mineral content; with finely disseminated aggregates of metal and non-metal minerals responding similarly to processing. The upgrade of the existing operations’ fine wet screening was implemented by Metalloinvest; as well as the design of a process flowsheet for concentration oxide ferruginous quartzites with low concentrating ability. The scientific basis for improvement of low grade ore concentrating efficiency and the upgrade of market product quality is supported by an in-depth study of ore characteristics, application of high performance equipment for separation of fine-grained mineral aggregates and use of depressor selective to ferruginous minerals in the flotation process. The benefits of wet fine screening have been proven by industrial scale tests; as well as the feasibility of significant upgrades in product quality which have been confirmed as a result of the tests. A road-map for the upgrade of an existing process for the concentration of unoxidised ferruginous quartzites deposited in the Mikhailovskoye ore field was developed, based on the industrial scale test of a fine screening process. With reference to the ability for concentration, three major ore types oxidised ferruginous quartzites were defined as a result of comprehensive geological mapping and process sampling: oxidised ferruginous quartzites with good concentrating ability: over Fe67% grade of concentrate with ca. 80% iron recovery; oxidised ferruginous quartzites with moderate concentrating ability: Fe65-67% grade of concentrate with 70-72% iron recovery oxidised ferruginous quartzites with low concentrating ability: below Fe60% grade of concentrate (cannot be processed into desired grade market product). A process flow diagram combining magnetic separation and flotation has been designed and recommended for implementation based on the in-depth research of defined Mikhailovskoye deposit iron oxide types, including grain size, chemistry, petrographic, mineralogy, hematite and magnetite grain size distribution and liberation analysis.

Jan 1, 2020

By I. Druce, C. Li, T. Qu, J. Dong, W. Y. Xinchao, V. Nkuna

CITIC Heavy Industries has a large installed base of grinding equipment throughout Africa in different configurations, including high-pressure grinding rollers with ball mill and semi-autogenous ball crusher. The total installed power of CITIC’s mills exceeds 430 MW. In this paper, we compare several typical grinding circuits of copper in Africa with about 15 kt/d throughput based on ore properties, process selection, equipment sizing, and key equipment capital and operating costs. Actual operating performance is also introduced. The comparison for the following mine sites provides a general reference for the selection of copper grinding circuits with this approximate throughput: Kamoa-Kakula Copper Mine with high-pressure grinding rollers with ball mill circuit, and Deziwa and Sicomine Copper-Cobalt Mines with semi-autogenous ball crusher circuits

Jan 1, 2023

By F. F. Roxborough, P. King, E. J. Pedroncelli

This paper describes tests on the performance of a continuous miner in cutting South African coal. Although coal cutting has been investigated extensively overseas, the results have not led to significant changes in machine design because these machines find little difficulty in cutting the softer overseas coals at a fast rate. In general, the results of the tests show that cutting efficiency improves markedly as the depth of cut per revolution of the drum increases, and that the best spacing of picks on the drum is twice the depth of cut. Pick shape is of secon¬dary importance in terms of cutting efficiency, only small differences having been found between the performances of conical- and chisel-shaped tools.

Jan 1, 1981

The following are available from Metal Bulletin Books Ltd, Park House, Park Terrace, Worcester Park, Surrey KT4 7HY, England. . World aluminium-a Metal Bulletin databook. 2nd ed. 1990. £71.50 surface, £76.50 airmail. This is a compendium of information listing salient details of companies mining bauxite and producing alumina, primary aluminium, secondary ingot, master alloys, and semi-fabricated products; aluminium trading companies; and a memoranda section listing associations, brand names, and other useful information. It is a userfriendly international reference book for aluminium buyers, traders, and producers.

Jan 1, 1991

By P. J. A. Beukes, C. C. La Grange

INTRODUCTION Some years ago the authors proposed a modified procedure1 for carrying out micum index determinations2. The modifications consisted of using a drum of 50 cm internal length, i.e. half the length of the standard micum drum (a modification also adopted by the B.S.J.3), and the use of a + 25 mm coke instead of + 60 mm coke for the test. The proposed modified test and formulae for converting results obtained from it to standard micum test results and vice versa were based on the results obtained during the investigation of about 200 test cokes made in ovens of the South African Steel Industrial Corporation Limited (Iscor), the Fuel Research Institute co-operating with the experiments. Extensive testing of cokes has since been done at the Fuel Research Institute using both the standard and the modified procedures. The numerous test results obtained during this trial period fully support and strengthen the confidence originally expressed by the authors in the modified testing procedure. The scope of the modified micum index determination has in the meantime been extended by applying the testing procedure also to test cokes made in the Institute's experimental coke ovens, and also in this case the modified procedure has proved its usefulness. A difficulty is that when comparing the characteristics of cokes made in the Institute's two experimental coke ovens with each other and with those of cokes made from similar blends in commercial coke ovens, for example those of Iscor, the index values obtained invariably do not check exactly due mainly to inherent differences between the different types of oven4. For instance, resistance to abrasion of a coke made in Iscor's ovens is always appreciably higher than that of a coke made from the same blend (and having a similar moisture content) in the experimental ovens. This makes direct comparisons and the prediction of quality to be expected from commercial products, based on experimental coke oven results, difficult. It may also be added that workers in Great Britain some years ago reported a similar experience5. In the authors' opinion the main reason for the discrepancy is the relatively low height of the experimental ovens resulting in a much lower static pressure on the charge during coking than that obtaining in a commercial oven. The difficulty was pointed out and briefly discussed in a publication4 which appeared at a time when the micum test for coke evaluation had only just been introduced at the Institute, so that only B.S. shatter and abrasion test results were available for discussion in the publication. Needless to say, the introduction of the micum test by no means solved nor even alleviated the problem. On numerous occasions during the past few years the Institute has had to conduct contract investigations in its experimental coke ovens on behalf of companies which invariably desired an indication of the quality of coke likely to be obtained from certain coals or blends when coked commercially, more particularly in Iscor's type of coke ovens. It was, therefore, essential to accumulate statistical data which would enabe the prediction to be readily made. Fortunately the compilation of comparative coke-quality index values for the three types of oven under consideration has become possible as a result of coking investigations conducted in co-operation with Iscor over a number of years. During this period Iscor, on numerous occasions, kindly made available to the Institute portions of coals and blends coked in the Corporation's coke ovens, thus enabling parallel coking tests to be carried out in the Institute's experimental ovens. In this way enough statistical data became available to establish relationships between coking results obtained in Iscor's ovens and results obtained on similar coal charges in the Institute's ovens. The most practical and acceptable method of overcoming the problems of finding a suitable and simple basis enabling direct comparison between the cokes of the different origins mentioned to be made, is the assignment of descriptive arbitrary quality ratings, as indicated below, to the cokes obtained, it being argued that the quality rating assigned to coke made from a given coal or blend in the different coke ovens under standardized conditions should be the same, irrespective of differences in the index values obtained when subjecting the cokes to the usual coke evaluation tests. The system, which should enable the sponsors of coking investigations in the Institute's experimental ovens to make their own interpretations of the results obtained, is explained below. ARBITRARY QUALITY CLASSIFICATION OF COKES The Ml0m index1 (percentage material smaller than 10 mm after the test) of a blast furnace coke is a measure of its tendency towards breeze formation during handling -a low value indicating a low tendency. This is generally of greater importance under ruling South African conditions, than the M'40 index1 (percentage material larger than 40 mm after the test), which can be regarded as a measure of resistance to shatter. In fact, if the M10m value of a coke as made in Iscor's ovens is higher than about 11, the tendency of the coke to form breeze during handling and in the blast furnace is relatively so high that hardly any notice need be taken of its M'40 value, even if this is comparatively high. For this reason, therefore, much more weight should normally be assigned to Ml0m indices in the quality evaluation of cokes made from South African coking coals and blends, as the coals

By F. L. D. Cloete

The following discussion relates to the paper by G. S. Hansford, C. D. Levy, and J. W. de Kock that appeared in the March 1976 issue of the Journal (vol. 76, no. 8, pp. 363-369) Competition for student members Each year the South African Institute of Mining and Metallurgy offers a prize (or prizes should the entries warrant it) of up to RI00 for the best paper or dissertation on a topic appropriate to the interests of the Institute. Engineering in South West Africa The SW A Engineering Profession Steering Committee was established on 4th April, 1977, its purpose being to formulate an Act covering the engineering profession in South West Africa.

Jan 1, 1978

By D. van Heerden, M. F. Breed

"Successful development of projects or life-of-mine strategies requires an understanding of the relative sensitivity of value drivers such as grade, tonnage, energy costs, direct operational costs, and recoveries. For example, the results could vary significantly depending on the grade strategy, given a specific orebody amenable to open pitting.Pit optimization is a very powerful tool widely used in the industry to determine the pit shell with the most attractive value potential. Based on the input parameters utilized, the pit optimization process determines the stripping ratio, mineable reserves, and pit shape, and effectively calculates a cut-off grade, assumed to be the optimal cut-off grade.Once the initial pit optimization process is completed, the need may arise to align the optimization results with the company strategy by further optimizing other criteria, such as maximizing short-term cash flow. This paper describes and discusses the selection of an alternative cutoff grade as a strategic intervention. It involves changing the cut-off grade, effectively increasing the head grade to gain a strategic advantage aligned with the company strategy, with a clear understanding of the financial value impact. With this knowledge, it is clear that pitoptimization establishes the basis for future analysis and refinement.IntroductionIt is common for companies to select the optimal pit shell defining the mineral reserve without much further consideration. However, companies may consider various strategies to optimize the long-term value of the project or to optimize the short-term cash flow. Analysis of the entire life-of-mine value estimation process shows that the selection of a cut-off grade and other parameters should be based on careful analysis. Determining the optimal cut-off grade of ore at a different period during the life of mine to maximize the value is often one of the most difficult challenges for a company.A cut-off grade is the lowest grade that mining activities will target. As a result the average mining grade, which drives the value of a project, will always be higher than the cutoff grade applied.According to Bascetin and Nieto (2007) cut-off optimization is still not widely practised. Cut-off grade optimization is an effort to maximize the value of a project by understanding the capacity constraints in the mine, mill, and the market. At any point during the life of mine, any or all of the limitations on tonnage mined, tonnage milled, and product sold may be constraining the system. To ensure cut-off optimization is done correctly, the capacity constraints must be independent of the cut-off grade."

Jan 1, 2016

By T. Bui, T. Wallmach, S. B. Blancher, A. Back, M. Pierre, V. Delarue, A. Kanzari

This study investigates nickel laterite porosity and its impact on geometallurgical modelling. We performed a detailed mineralogical study on a set of Ni-laterite samples originating from New Caledonia. Samples were analysed after heavy liquid separation by automated SEM (QEMSCAN®). Laboratory and QEMSCAN® modelling results do not correlate well. Ideal physical mineral properties such as mineral densities used in QEMSCAN® modelling do not match the actual physical densities of minerals. The presence of empty or water-filled pores can represent important amounts in minerals and change the overall density of a particle. An adequate modelling of real density separation of minerals and particles should consider the water-filled pores. The first step towards a better simulation was to integrate pores larger than 10 μm in diameter filled with water (density of 1 g/cm3) in the QEMSCAN® database. The results approached, but did not match the physical laboratory results. The second step was to identify nanometer to micrometer sized pores, which could not be identified by QEMSCAN®. It was possible to identify nanometric pores in enstatite, Fe-oxides, serpentine, talc and quartz, and radial aggregates of fibrous Fe-oxyhydroxides with high resolution SEM (HR-SEM). The quantification of those micro-sized pores was performed on 2D HR-SEM images using image-processing techniques developed in Python to calculate the nanometer to micrometer scale pores in each mineral. Despite the limitation of converting 2D imaging into 3D objects, in our case pore sizes and porosities, we were able to calculate a mean value of porosity for each mineral. The integration of this porosity in the calculation of particle densities yielded a good match between the QEMSCAN® model and the laboratory experiment results. Despite the complexity of a strongly weathered material, such as Ni-laterites, a good knowledge of the ore makes it possible to build reliable processing models. Keywords: Mineralogy, geometallurgy, nickel laterites, SEM, QEMSCAN®, porosity, density

Jan 1, 2020

By T. Tholana, P. N. Neingo

"A mineral resource constitutes the principal underlying asset of a mining company, and must be exploited and managed in such a way that maximum value is derived from it. Various asset management frameworks applicable to physical assets are available. This paper focuses on the extension of an asset management approach, particularly the Publicly Available Specifications (PAS) 55 asset management framework and the International Organization for Standardization (ISO) 55000 series of standards, to mineral assets. It is concluded that PAS 55 and the ISO 55000 series of standards can be extended to manage mineral assets, resulting in an integrated approach to sustainably optimize value from the company’s mineral assets. The benefits include improved returns on mineral assets, maximum mineral asset utilization, creation of an organizational culture focused on quality and continuous improvement, and assurance to stakeholders that the mineral assets are being efficiently managed over their entire life-cycle. In the context of this paper, a ‘mineral resource’ refers to both Resources and/or Reserves as classified by the SAMREC Code. IntroductionMining involves the extraction of valuable mineral resources from the Earth’s crust. A mineral resource is unique among natural resources in the sense that it is a wasting asset, which means that its value depreciates continuously with extraction. In addition, it is often impaired from time to time as commodity price changes (Macfarlane, 2011a). Since a mineral resource is a wasting asset there is a single opportunity available to optimize value from its extraction. Mine planning involves identifying a strategy to exploit the mineral resource in a way that maximizes value at an acceptable risk level throughout the life of mine (LOM). This optimum extraction strategy changes as economic conditions change, particularly commodity prices, as well as with improvements in orebody knowledge as mining progresses. It is the mineral deposit that competitively distinguishes two different mines and dictates the location of a mine; hence the adage ‘the orebody dictates’. Therefore, a mineral resource is the primary tangible asset possessed by mining companies and must be managed in such a manner that maximizes its value at an acceptable risk level (Macfarlane, 2011a)."

Jan 1, 2016

By J. P. Hoffman

In 1988 the Japan Iron and Steel Federation started a research-and-development programme known as DIOS (direct iron-ore smelting). Eight Japanese integrated steel producers and the Coal Mining Research Centre, subsidized by the Ministry of International Trade and Industry, are involved in the project. The aim of the programme is to have a 500 v/d pilot plant for the production of iron via an oxygen-coal in-bath smelting converter in operation by mid 1993. The three main components of the DIOS process are as follows: ?a fluidized bed for the pre-reduction of iron-ore fumes ?in-bath smelting reduction in a converter ?off-gas reforming by the addition of coal fines. The main drive is to provide a smelting process that is more energy-effective, using coal instead of coke and/or electricity. The advantages claimed include inter alia ?direct use of fine iron ore ?direct use of non-coking coals-low coal consumption ?low capital expenditure-replaces costly coke ovens, agglomeration plants, and the blast furnace ?economical production on mini-plant scale ?less of an impact on the environment. This concept of 'direct steel has been carried over to the production of stainless steel direct from the ores, again bypassing such energy-intensive units as the submerged-arc furnace for the production of ferrochromium. A number of Japanese companies have indicated a certain amount of success. Several interacting elements are recognized that could have a productivity-limiting aspect. The possibility of the direct production of stainless steel from chromite is discussed briefly with reference to the Highveld of the eastern Transvaal as a possible site for such a plant

Jan 1, 1992

By F. P. Agterberg, A. G. Fabbri

"A statistical analysis was done on the locations of 718 copper and 1 257 gold deposits in Abitibi. This area of about 20 000 square miles is one of the better-explored metal-producing areas of Canada.Patterns of clusters were studied by harmonic analysis. Several two-dimensional power spectra showed a number of distinct peaks. Sets of crest lines for patterns of interfering waves were constructed on the basis of these peaks. They pass through elongated clusters of deposits which are spaced more or less equally. For copper these periodic regularities in location may coincide with geological structures largely of Archean age (major fractures and sedimentary belts indicating synclinal structures). A directional relationship with swarms of diabase dykes of known ages and distinct attitudes indicates that the gold mineralization is, in part, younger than the copper mineralization."

Jan 1, 2014

By Huanhuan SU, Jianqiang Zhang, Zhongyuan Liu, Junwei Ma

The high-sulfur bauxite in Henan Province was used as raw material. The grinding fineness, pH value and collector dosage on its desulfurization performance, and industrial flotation desulfurization process were studied. The best flotation desulfurization conditions were grinding fineness of 75%, pH of 8.5, and collector of 600 g/t. “One coarse, one cleaning and one sweep” closed-circuit flotation was established as the industrial flotation desulfurization process. After the closed circuit test, the sulfur content of aluminum concentrate with the yield of 93% was 0.23%, and the sulfur removal rate was 83.16%, and the sulfur content of tailings (sulfur concentrate) was 15.09%. Keywords：High-sulfur bauxite under coal mines, flotation, desulfurization

Jan 1, 2020

The paper deals with the importance of design, and of codes of practice, in ensuring safe working conditions in mines. The design principles involved in the design process are dealt with, and the importance of a logical design process is emphasized. The links between the requirements for developing a code of practice, embodied in the existing guidelines for the preparation of such a code, and the design principles and process are considered in some detail. Finally, suggestions are included which may provide improvements to the code and hence, ultimately, lead to further improvement in safe working conditions.

Jan 1, 2003

By M. Saghaeian, R. Hejazi, L. Hosseini, M. V. Sheikhzadeh

HPGR equipment has been well proven to be energy-efficient in the first stage of grinding in iron ore beneficiation plants. Numerous advantages of utilising HPGR grinding prior to ball mill grinding, such as reducing the power consumption in a ball mill through generation of micro-cracks, has been thoroughly studied. Less attention has been paid to efficiency of the HPGR circuit rather than the downstream ball mill circuit. In this study the HPGR circuit has been optimised through feed size reduction by crushing, and feed iron content upgrading by dry cobbing. This optimisation leads to better operation of the HPGR, and a smaller product size which is expected to result in a lower wear rate of ball mill liners and balls. It is also expected that the top size of the ball mill balls be reduced. Additionally, by reducing the feed size of HPGR from 30 mm to 15 mm, it is possible to achieve similar K80 of HPGR product in lowered pressure, i.e. 2.5 N.mm-2 instead of 3.5 N.mm-2 which translates to ease of operation. Similarly in a given roll pressure, smaller feed sizes result in higher specific throughput of ~10% which means higher production capacities. The results also reveal that this optimisation increases the concentrate weight recovery by about 10%. It also results in slight increases in the Fe grade of the product iron concentrate. Keywords: HPGR, HPGR circuit optimisation, crushing prior to HPGR, dry cobbing prior to HPGR, ease of operation, concentrate grade optimisation, weight recovery optimisation

Jan 1, 2020