Search Documents

By P. Vlasak, Z. Chara

Since the flow behaviour of slurry containing both coarse and very fine particles has not been sufficiently clarified, the paper focuses on the experimental study of the particle size distribution, time and intensity of shearing and the effect of chemical agents on the hydraulic gradient versus the average velocity relationship of fluidic ash slurries in the laminar and turbulent regimes. The recirculation pipe loop with smooth stainless steel pipes of inner diameters 26.8 and 36 mm was used for measuring the ash-water mixtures flow parameters. The dense fluidic ash-water mixtures behave as time dependent non-Newtonian slurries. Shearing, the addition of bottom ash or chemical agents, favourably affects the flow behaviour of dense fluidic ash-water slurries. The hydraulic gradient in the laminar region significantly decreases; also the laminar/turbulent transition region is reached for lower flow velocity.

Jan 1, 2007

By L. Bam, R. Machaka, S. Chikosha, N. S. Muchavi

"Parts manufactured through power metallurgy (PM) typically contain pores that can be detrimental to the final mechanical properties. This paper explores the merits of 3D X-ray computed tomography over traditional microscopy for the characterization of the evolution of porosity in metal injection moulding (MIM) and direct powder rolling (DPR) products. 17-4 PH stainless steel (as-moulded, as-debound and sintered) dog-bone samples produced via MIM and Ti-HDH strips (as-rolled and sintered) produced via DPR and were analysed for porosity. 3D microfocus X-ray tomography (XCT) analysis on specimens from both processes revealed spatial variations in densities and the existence of characteristic moulding and roll compaction defects in agreement with traditional microscopic microstructural analysis. It was concluded that micro-focus XCT scanning can be used to study MIM and DPR parts for the characterization of the amount, position and distribution of porosity and other defects. However, the majority of the sub-micron sized pores could not be clearly resolved even at the highest possible instrument resolution. Higher-resolution scans such as nano-focus XCT could be utilized in order to fully study the porosity in MIM and DPR parts. IntroductionMetal injection moulding (MIM) is a novel process, which combines the advantages of powder metallurgy (PM) and plastic injection moulding. MIM has found widespread applications in the cost-effective production of high-sintered density small parts with complicated shapes and mechanical properties equivalent to those of wrought materials (German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013). There are four basic processing steps involved in MIM, namely; feedstock preparation, injection moulding, debinding and sintering. These steps are discussed in greater detail elsewhere (Machaka, Seerane and Chikwanda, 2014; German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013).Feedstock preparation involves mixing metal powder with a carefully selected composition of polymeric binder materials at a specific temperature. The feedstock is then granulated and injected into a predefined mould die with the desired shape. The part produced during the moulding step is referred to as a ‘green’ component. The green component typically contains no porosity since the spaces between adjacent powder particles are readily filled with the binder materials (German and Bose, 1977; Li, Li and Khalil, 2007). Debinding is the systemic removal of the binder components by chemical, catalytic, or/and thermal means while maintaining the shape of the component. The part produced after the debinding step is referred to as a ‘brown’ component. Debinding is known to be the source of porosity in brown components (Ji et al., 2001; Tsai and Cen, 1995). Finally, the brown debound part is sintered to full or nearfull density (Sotomayor, Varez and Levenfeld, 2010). The sintering step and associated densification closes up the majority of the pores. Sintered MIM parts are typically sintered to high density (95–99%) and retain an irreducible amount of residual porosity (Barriere, Liu and Gelin, 2003; German, 1990)."

Jan 1, 2016

By B. Jack, A. Vervoort

During pillar extraction, sidewall fracturing and spalling at some collieries constitute a severe stratacontrol problem. In order to obtain a better understanding of this phenomenon, a survey of pillar corner conditions before and during pillar extraction was conducted at one particular site. For the various successive mining steps, the vertical stresses on the pillar corners were calculated by use of a three-dimensional boundary element program. A significant correlation was found between the calculated vertical stress prior to the extraction of the panel and the sidewall conditions. During the extraction of the panel, a significant deterioration of the sidewall conditions at a pillar occurred only when the adjacent pillar was mined, causing an increase in vertical stress on the remaining pillar.

Jan 1, 1992

By Mark Craddock, Johan Swanepoel

In this paper we present The Ultimate Flotation Cell, a newly developed flotation cell that is proving very popular in the industry. All flotation cells have only one purpose and that is the recovery of the required product, the patented impeller and disperser system of the Ultimate Flotation Cell allows total flexibility in order to achieve the optimal recovery. This ability to tune the cell performance provides the optimization of the ?capture? (collection) stage, all existing models address the need for a wide bubble size distribution (100µm-2 mm) to obtain a better flotation size-by-size, Yoon, 1999,Yoon 2000, Franzidis and Manlapig, 1999. The Ultimate Flotation Cell provides flexible performance optimization. This ability to optimize the flotation regime particular to a specific ore is achieved by the following factors: ? The impeller allows vastly improved air induction rates compared to conventional and sparged cells. This ability to induce and disperse large quantities of air, in a controlled manner, allows the cells to be tuned to give the optimal Sb by varying the rotational speed via a VSD which every cell is fitted with. ? The patented impeller gives a very constant and stable air induction rate, which ensures that the cell?s circulation pattern is constant, giving a very stable surface, allowing optimal froth depth. ? Although conventional dart valve, level control can be offered, great success has been achieved with a simple draft tube/sand relief device. ? The cells have a inlet design similar to the old Denver ?Cell-to-Cell? design, which guarantees the at lease one pass through the mixing zone in each cell. Actual plant performance data will be presented from two plants, one in Zambia and the other in the DRC.

Jan 1, 2007

By K. N. Karparov

The stress state on two slope profiles overlying an inclined surface with layer inclination of 50 and 150 are investigated. It is demonstrated that the induced stress state in an imbedded weak layer, exposed at the base of the slope, forms a zone of induced tensile vertical and horizontal stresses, which can lead to failure. The zone length depends on the slope angle and the angle of the inclined layers. L’état des contraintes sur deux profils en pente en superposition sur une surface inclinée avec une inclinaison de couche de 5o et 15o est étudié. L’étude présente démontre que l’état induit des contraintes dans une couche faible insérée, exposée au bas de la pente, forme une zone de contraintes de traction induites horizontales et verticales, qui peut amener à la rupture. La longueur de la zone dépend de l’angle de la pente et l’angle des couches inclinées. Die Druckvorkommnisse zweier Hangprofile auf einer schrägen Fläche mit einer Schichtneigung von 5º und 15º wurden untersucht. Es zeigte sich, dass die induzierten Druckvorkommnisse in einer eingebetteten schwachen Schicht, die am Hangfuße offen liegt, einen Gürtel induzierter vertikaler und horizontaler Zugkräfte bildet, die zum Zusammenbruch führen können. Die Gürtellänge ist von der Neigung des Hanges und der Neigung der schrägen Schichten abhängig.

Jan 1, 2003

By P. L. Moolman

An approach to the design of a tailings disposal system is presented using an example from a platinum project on the eastern limb of the Bushveld Complex as a base case. The design is driven by two inputs: namely, maximizing water recovery and minimizing power cost, expressed as cubic metres and kilowatts per ton of solids deposited on the tailings storage facility respectively. The approach considers low-, medium-, and high-density platinum tailings and uses material-specific aspects such as thickening and rheology to determine the most economical option. An analysis based on direct capital and operating cost (water and electricity) shows that the medium-density scenario results in the lowest total cost per ton of tailings deposited, even though this system results in the highest electricity consumption per ton of tailings deposited. As the cost of water and electricity is likely to increase in the future, the higher-density tailings disposal options become more economical, with the paste option the preferred option.

Jan 1, 2012

By G. D. Schena

The issue of evaluating the economic impact of large mineral projects in developing countries was studied by the use of econometric models. The evaluating system is demonstrated by its application to an example from Namibia. Three-dimensional graphics are used to illustrate the procedures leading to an assessment of the economic effects of the mineral development. The analysis allows the assessment of the overall economic consequences of mineral developments where there is a need to incorporate in the evaluation issues that are broader in scope than the pure financial objectives. Sets of technical coefficients are exploited for the development of input-output models of the productive structure of an economy. The models are refined to incorporate country-specific behaviours. The increased flexibility of the enhanced semi-input-output model permits a more confident investigation of the economy wide effects associated with a new project in the mineral sector of a developing country. Synthetic measures of profitability at market and shadow prices are introduced, and the cost/benefit ratio is used to rank mineral projects according to their economic profitability. The cost is the capital mobilized for the development of the project and for increasing the productive capacity of the related satellite industries. The benefits are identified with the economy-wide increase in value added induced by the project. 80th costs and benefits are initially valued at market prices. Their ratio is likely to be an index of economic profitability superior to measures that concentrate exclusively on the benefit side of projects. To allow for market distortions, the concept of shadow prices is introduced, and accordingly project-related costs and benefits are re-evaluated. A new cost/benefit ratio at shadow prices is recalculated, which is more meaningful to the policy-maker than decision-making based on socio-economic issues.

Jan 1, 1993

By B. Zlender

ABSTRACT: The paper presents investigation of carboniferous slates from the Trojane hilly area performed on series of samples of equal material. The results of static loading tests show that carboniferous slate is heterogeneous and yields on slate layers. Where that kind of heterogeneity is distinctive the strength results are essentially lower of commonly tests results. The results of dynamical loading tests show that the slate surfaces have the essential meaning for the stability of the material. When those surfaces are moistened the material become unstable. RÉSUMÉ: L'article présente une épreuve des ardoises carbonifères de la région montagneuse de Trojane sur une série des échantillons des matériaux identiques. Les résultats des tests de charge statique montrent que l'ardoise carbonifère est hétérogène et qu'elle cède sur les couches d'ardoise. Quand l'hétérogénéité est distinctive, les résultats de stabilité sont essentiellement plus bas que les résultats obtenus par des tests ordinaires. Les résultats des tests de charge cyclique montrent que les surfaces d'ardoise sont très importantes pour la stabilité du matériel. Quand ces surfaces sont mouillés, le matériel devient instabile. ZUSAMMENFASSUNG: Der Artikel präsentiert die Forschung von Karbonschiefersteinen im Bereich des Bergland Trojane, ausgeführt durch Serien von Proben aus den gleichen Erdmaterial. Die Resultate der statischen Belastungsprüfungen zeigen, das die Karbonschiefersteine heterogen sind und die Schieferflächen nachlassen. Wo bei dieser Art der Heterogenität die Festigkeitsergebnisse wesentlich niedriger sind als bei gewöhnlichen Testergebnissen. Die Ergebnisse der zyklischen Belastungsprüfungen zeigen das die Schieferflächen eine wesentliche Bedeutung für die Stabilität des Erdmaterials haben. Wen diese Schieferflächen befeuchtet sind, wird das Erdmaterial unstabil.

Jan 1, 2003

By J. Abdollahisharif

Optimal cut-off grade is one of the most critical parameters in open-pit mine design because it defines the ore and waste and thus determines the maximum net present value possible from the mining operation. Although the algorithm presented by Lane (Choosing the optimum cut-off grade. Colorado school of Mines Quarterly, vol. 59, no. 4, 1964. pp. 811-829) is the most common one in the literature, it does assume constant capacities of the mine, processing, and refinery. In this paper, Lane's original algorithm has been modified to consider variable processing capacities in order to determine the optimal cut-off grade in open-pit mines. The new algorithm proposed here is compared to both Lane's original algorithm and to a previous modification that incorporated rehabilitation costs into the cut-off grade estimation. The algorithm proposed here that permits variable processing capacities is shown to be superior for the determination of optimal cut-off grade to both these previous versions. In addition, a computer-based program was developed in Microsoft Office Excel© to calculate the optimal cut-off grade as proposed here.

Jan 1, 2012

By A. J. Jager, G. R. Adams

The pattern of mining-induced fractures ahead of stope faces in deep-level gold mines, as revealed by petroscopic observations, is described. It is shown that there are zones of fractured and unfractured rock ahead of the face, which are about I m wide and continue as discrete entities for at least 12 m parallel to the face and at least 5 m vertically. These zones do not form continuously as mining progresses, but develop from time to time, leaving a solid zone between the fractured zones. The maximum depth of fracturing ahead of the face depends on the rate of energy release.

Jan 1, 1980

By C. A. Rawlins

Deep underground mines use refrigeration systems to provide a reasonably comfortable ambient environment to increase productivity and to maintain safety as a priority. Deep level gold mines maintain the environment at an acceptable temperature, i.e. 27°C. However, the increasing cost of doing so through refrigeration is becoming a significant factor in the economic viability of mines. This paper discusses of the important facet of energy losses in cooling reticulation systems, laying with the specific emphasis on the subject of chilled water transport pipe insulation and its thermo-dynamic relationships. Aspects relating to the deterioration of open cell-type insulation materials such as polyurethane/styrene foams and the use of Phenolic resins that have good fire retardation properties have been investigated. The thermal conductivities of these insulation media are good (meaning below 0.05 W/°C)However, they are known to be negatively influenced by water vapour ingress and vapour pressure differences that result in the ingress of water into the material by means of absorption, condensation, hygrospicity, permeability and capillary action, to name a few of many. The overall effect on mine cooling efficiency takes in the two forms: first by the loss of refrigeration or increased chill in the water temperature arriving in a given section and second, by a loss in transfer efficiency when the gap between the arriving water temperature and the actual air temperature decreases. Keywords: Conductivity, vapour, insulation, fluid, thermal, temperature, pressure, transport, refrigeration.

Jan 1, 2007

To determine the characteristics of a mineral deposit, the usual practice is to take samples, analyse the properties of those samples and infer the characteristics of the deposit from these properties. This analysis can be done using statistical methods. In the present work we are concerned with two types of statistical approaches, classical statistics and spatial statistics. If one uses classical statistics to represent the properties of the sample values, the assumption is made that the values are realizations of a random variable. The relative positions of the samples are ignored, and it is assumed that all sample values in the mineral deposit have an equal probability of being selected. The likely presence of trends, zones of enrichment, or pay shoots in the mineralization, is ignored. The fact that two samples taken close to each other are more likely to have similar values than if taken far apart is also not taken into consideration. In contrast, spatial statistics will be used if one chooses to consider that the sample values are realizations of random functions. On this hypothesis, the value of a sample is a function of its position in the mineralization of the deposit, and the relative position of the samples is taken into consideration. The similarity between sample values is quantified as a function of the distance between samples and this relationship represents the foundation of spatial statistics. There are few situations where classical statistics can be used. The assumption that all sample values in the mineral deposit have an equal likelihood of being represented will be satisfied only if the sample values are randomly distributed, or if the sample positions are random. Sample values are in fact never randomly distributed within a mineral deposit. Further- more, geologists usually avoid taking samples at random (random sampling), as it is correctly accepted that samples located on a regular grid, or approximately on a regular grid, give more information than randomly located samples. In practice, classical statistics should be used only in the early stages of exploration, when the number of samples available is relatively small and the distances between samples are large. In these circumstances, and whenever the information available is not sufficient to permit the use of spatial statistics, application of the methods described in this chapter is justified.

Jan 1, 1978

By R. Tabanrad

This article examines the stability analysis of intake tunnels of Karun III dam & power plant. The tunnels have been excavated with a 3-dimensional and fairly complicated geometry in Pabdeh weak formation rocks at Zagros region. Due to the particular excavation geometry and inapplicability of plane-strain status, the stability of these excavations has been analyzed using both the 3D elastic software Examine 3D and the 2D non-elastic software UDEC simultaneously. The geomechanical parameters have been estimated by back analyzing the measured displacements from instruments, which were installed in the tunnels, and the parameters have been used in non-elastic numerical model. The results of the analysis show that the strains occurred in surrounding rock mass are less than the allowable failure strain and that the tunnels are stable. In addition, considering the results of non-elastic 2D analysis, the areas with unstable potentiality were identified and after the instability occurred at the areas predicted by the model , it was stopped up to the allowable strain limit through installing additional support . Bei diesem Artikel handelt es sich um eine Analyse der Festigkeit der Eingangstunnel des Damms und Elektrizitätswerks “Karoon III”.Die Tunnel haben drei Dimensionen und eine sehr schwierige Form und sind in brüchigen Felsen in “Pabedeh ,in Zagrossgebirge”eingebohrt.Aufgrund besonderer Form der Bohrung wurde ihre Festigkeit durch elastische dreidimensionale Soft-ware analysiert,die gleichzeitig die drei-und zweidimensionale unelastische Soft-ware UDEC benutzt hat.Die geometrische Parameter sind mit Ausnützung der Analyse berechneter eingesetzter Versorgungen,die in Tunnel aufgebaut sind,bewertet.Und diese Parameter sind in Zahlen-Analyse benutzt.Die Ergebnisse dieser Analyse zeigen,dass die Drücke an Felsen weniger als problematischer Grad der Drücke sind und die Tunnel fest sind.Ausserdem wurde mit einem Einblick auf die Ergebnisse der unelastischen zweidimensionale Analyse die eventuellen unfesten Teile bestimmt.Nach entstandener Unfestigkeit an diesen Teilen wurde die problematischeDrücke für Aufbau mehrere Anlagen gestoppt. Cet article examine l'analyse de la stabilité de tunnels de la prise de Karoun barrage III et centrale électrique. Les tunnels ont été excavés avec une 3 dimensionnel et compliqué géométrie dans Pabedeh que la formation faible balance à région Zagros équitablement. Dû à la géométrie de l'excavation particulière et inapplicabilite de statut de tension plane, la stabilité de ces excavations a été analysée en utilisant les deux le 3D logiciel élastique Examen 3D et le 2D logiciel non - élastique UDEC simultanément. Les paramètres du geomechanical ont été estimés en analysant le déplacement mesuré d'instruments qui ont été installés dans les tunnels et les paramètres en arrière a été utilisé dans les modèles numériques non - élastique. Les résultats de l'analyse montrent que les tensions se sont produites dans masse du roc environnante est plus petit que la tension de l'échec admissible et que les tunnels sont stables. De plus, les régions avec potentialité instable ont été identifiées étant donné les résultats de 2D analyse non - élastique, et après que l'instabilité se soit produite aux régions prédites par le modèle, il a été arrêté jusqu'à la limite de la tension admissible à travers installer du support supplémentaire.

Jan 1, 2003

By Z. G. He, S. H. Chen, P. Egger

A new model for hollow rock bolts which comprises rock material, hollow bolt material, bolt/rock interface, is developed on the base of the composite element method (CEM). The main advantage of the new model is that it can be incorporated into the conventional finite element analysis. So the mesh generation of bolted rock structures becomes more convenient and feasible, which is very important in the optimisation of reinforcement design: the mesh can be kept unchanged when the number and orientation of bolts are adjusted. The comparison of the calculation results with a conventional FE approach shows the robustness of the proposed method. Un nouveau modèle numérique de boulons creux comprenant la roche, le matériau du boulon creux et l’interface roche / boulon est développé sur la base de la méthode des éléments composites (CEM). L’avantage principal du nouveau modèle est la possibilité de l’incorporer dans une analyse aux éléments finis conventionnelle. Ainsi la génération du maillage d’une structure rocheuse ancrée devient plus simple ce qui est très important pour une optimisation du projet : en cas d’ajustement du nombre et de l’orientation des boulons, le maillage reste inchangé. La comparaison de résultats de calcul avec ceux obtenus par un code aux éléments finis conventionnel montre la robustesse de la méthode proposée. Auf der Grundlage der Verbund-Element-Methode (CEM) wird ein neues Modell für hohle Reibungsanker entwickelt, das den Fels, das Ankermaterial und die Kontaktfläche Fels / Anker umfasst. Der Hauptvorteil des neuen Modells ist die Möglichkeit, es in eine konventionelle FE-Analyse einzubetten. So wird die Netz-Generierung für verankerte Fels-Bauwerke einfacher, was für die Optimierung des Verankerungs-Projekts von Wichtigkeit ist: wenn Zahl und Orientierung der Anker variiert werden, bleibt das Netz unverändert. Der Vergleich von Rechenergebnissen mit solchen aus einer konventionellen FE-Rechnung zeigen die Robustheit der vorgestellten Methode.

Jan 1, 2003

As part of a broad program to optimise the performance of their grinding circuit, BHP Billiton Cannington have installed an OCS© Expert system together with three VisioRockTM online particle size analysis cameras. The main purpose of the system is to stabilise grind size and feed to the flotation circuit. This particular application of OCS© is the first installation to incorporate Metso Minerals Process Technology-Asia Pacific's (MMPT AP) Dynamic SAG/AG Mill Model, which is able to predict numerous mill parameters that were previously unable to be measured with the existing plant instrumentation. Integrated into the logic of the control algorithm are online vision based, particle size measurements of the AG mill feed and recycle crusher product. This paper will describe the history of the project from initiation to date, the model and OCS© logic configuration, and demonstrate the significant benefits realised at Cannington mine.

Jan 1, 2007

Scrap printed circuit boards were selectively smelted at 1 200°C to produce a metallic alloy having three phases. These phases were identified as a lead-rich phase, a low tin content alpha bronze phase, and a high tin delta phase. Electrochemical leaching studies on this alloy were done in 1 mol/dm3 sulfuric acid or in 2 mol/dm3 hydrochloric acid (adjusted to an ionic strength of 3 mol/dm3). The lead rich phase was more strongly passivated in sulfate media, and in this medium the high tin content delta bronze was more resistant to corrosion than the lower tin alpha bronze phase. In chloride medium the lead phase and both bronze phases corroded readily, but with current densities about an order of magnitude lower than in sulfate medium (static conditions) for the bronze phases. The high tin delta bronze phase was found to form a passivating layer in sulfate media. A similar layer was not seen in chloride medium. The leaching studies in sulfate medium also showed the existence of an alpha bronze phase of lower tin content in the centres of the alpha phase grains. This phase was quite resistant to leaching in sulfate medium.

Jan 1, 2009

By S. Özgen

In this study, the possibility of beneficiation of chromite tailings in the Uckopru/Fethiye-Turkey region by a combination of hydrocyclone and multigravity separator (MGS) was investigated. The two significant operational parameters of hydrocyclone, which were diameter of the apex and diameter of the vortex, and the three significant operational parameters of the MGS, which were drum speed, tilt angle, and wash water, were varied and the results were evaluated with the central composite rotatable design. In order to produce a chromite concentrate by hydrocyclone and MGS, mathematical model equations were derived by computer simulation programming, applying the least-squares method using Minitab 15. Second-order response functions were produced for the grade and recovery of chromite concentrates.

Jan 1, 2012

The depletion of favourably located and higher-grade mineral deposits, combined with more favourable metal prices and higher capital costs, has stimulated research into heap leaching of lower grade ores and wastes. This has resulted in renewed interest in heap leaching of uranium ores, and in the development of processes for the bacterial heap leaching of low-grade chalcopyrite ores and the acid heap leaching of nickel laterites. A complete programme of heap leach testwork typically involves a sequence of bottle roll tests and column tests, followed by piloting on test heaps. The initial testwork is aimed at determining the amenability of the ore to heap leaching, which depends on the characteristic of the ore with respect to porosity and permeability to leach liquor, acid consumption, metal recovery and percolation. Subsequent phases of the testwork focus on the development of the process design criteria for the treatment of the ore. Basic techno-economic models have also been developed as a tool for the initial estimation of heap leach viability. Mintek has also developed in-heap monitoring probes, coupled to an operator guidance system, in order to assist the operator in achieving optimal conditions for bacterial growth and heat preservation during pilot-plant operation.

Jan 1, 2009

By R. Hemp

This paper describes in broad outline the development of a computer programme for determining the effects of changes in various factors in the condenser water circuit on the operation of a cooling plant. The programme is used to obtain design figures which result in minimum total power consumption. This was done for a range of different upcast air quantities, and the implications of low air quantities for heat rejection are discussed.

By C. M. Rule, A. K. Anyimadu, L. Knopjes

Ongoing development work on ultra-fine grinding for various applications at the Group?s concentrators has been conducted by Anglo Platinum over the last few years. Current potential applications for mainstream grinding and concentrate grinding are the subject of a group-wide research and development programme. The first 10 000-litre 2.6 MW IsaMill was jointly developed by Anglo Platinum, Xstrata Technology and Netszch for installation at the Western Limb Tailings Re-treatment project in Rustenburg, South Africa. The unit was commissioned in late 2003/early 2004, and has operated in an intermediate concentrate regrind application successfully since. This paper describes the operational performance to date, as compared with the original duty specifications and objectives. The first mainstream M10 000 IsaMill with a 3 MW drive will be operational in November2006 at the Potgietersrus Platinum (PPL) ?Platreef? Sandsloot Concentrator in South Africa?s Limpopo Province. Key Words: Western Limb Tailings Re-treatment Plant, IsaMilling, Platreef, Platinum, Palladium, PGMs, tailings.

Jan 1, 2006