Search Documents

The Copperbelt areas of Zambia and the Democratic Republic of Congo (DRC) have recently been seeing the development of a significant number of new projects. Due to the current economic climate, some of these projects have been delayed but the region remains an important resource for copper and cobalt for future years. Many of these projects will utilize an agitation leach followed by solvent extraction and electrowinning to recover both copper and cobalt. The flowsheet route for copper is fairly well established while the processing options for cobalt vary considerably depending on the final product (metal or salt) the operator wishes to make. The mineralogy of ores in the area is typically associated with high gangue acid consumption during the leaching process. This has resulted in acid availability to the area being constrained and acid prices have risen accordingly. Agitation leach circuits, typically, have a tight water balance which needs to be maintained and a bleed of process liquor needs to be continuously removed from the circuit in order to maintain this balance. This bleed, typically, contains fairly high levels of acid and requires neutralization prior to tailings disposal or secondary metal recovery. It is, therefore, desirable to minimize the acid concentration in this bleed stream in order to decrease total acid requirements and neutralization costs for the process plant. An in depth case study by Cognis and Bateman Engineering evaluated three different flowsheets with the aim of determining relative operating costs between the three alternatives, together with differences in plant capital cost requirements.

Jan 1, 2009

By D. G. Wymer, A. G. du Plessis, N. C. Joughin

The use of a dense hangingwal-support configuration extending right up to the face would enable greater levels of safety and productivity to be achieved in stopes, and becomes a practical proposition if water jets are used for stope cleaning. Such an arrangement opens the way for extending the use of water hydraulic power to the whole stoping operation. This, in turn, can provide further productivity benefits and significant savings in working costs. With al the necessary equipment being available, such a system could be introduced immediately, although the designs of props and rockdrills are not yet ideal.

Jan 1, 1989

By H. Von Michaelis

The world is rapidly becoming more ?green? i.e. energy conscious. Since mining and mineral processing are massive energy users, the mining industry is seeking ways to reduce its energy footprint. In mining and mineral processing operations, energy is often the most expensive cost item. Comminution, i.e. grinding, is frequently the most energy-intensive step between mine and metal. High pressure grinding rolls (HPGR) are being installed in a rapidly growing number of ?hard rock? mineral processing operations. In the energy conscious cement industry, HPGR grinding has been standard practice for decades. HPGR is known to be energy-efficient; the question is how energy efficient? How can the energy efficiency of HPGR be enhanced? This paper reviews recent HPGR applications for the processing particularly of copper, gold, platinum, PGM-Ni-Cu and iron ores. HPGR technology is discussed with respect to energy efficiency. The harder the ore the greater the energy savings are likely to be. Typical energy savings of 10?20% can be expected when installing HPGR vs. a SAG mill. Wipf(2005) showed why conventional Bond Work index tests on HPGR product is likely to under-estimate the energy savings that can be achieved by installing HPGR. Energy efficiency of HPGR is, however, ore-specific. The biggest energy savings of HPGR tested thus far is 9.5 kWh/tonne claimed for Vista Gold?s Mt. Todd gold ore from Western Australia, a savings of over one-third of conventional SABC comminution energy. Several commercial scale iron-ore pellet feed plants install HPGR for fine-grinding of concentrate to increase the surface area of pellet feed in a manner that reduces overall energy consumption. Energy-consumption in comminution is, however, only part of the energy savings benefit story. HPGR typically also reduces the amount of steel lost through wear of mill liners and media. Marsden(2008) showed that when the energy that would have been consumed to produce the steel that is saved by applying HPGR is factored in, then the overall energy savings of HPGR is considerably greater. Johnson et al.(1988, 2005) tested HPGR in a flowsheet in which energy savings of around 50% can be expected if HPGR product screen oversize is recirculated to the HPGR. Innovative flowsheets have been proposed by Rule et al.(2008) and by Morley (2008) which are expected to result in significantly increased energy savings. HPGR applied in flowsheets in conjunction with coarse ore separation devices, e.g. ore sorting or DMS to remove barren waste from HPGR feed promises significantly greater energy efficiencies. Fine-grinding and ultra-fine grinding of ore or concentrates in conventional ball mills results in energy consumptions that increase exponentially with product fineness. Wipf (2009) presented a flowsheet in which he proposed the installation of HPGR ahead of the Aerosion ?Disintegrator? for ultra-fine grinding of ores and/or concentrates. This dry grinding arrangement is expected to achieve ap80 = 7 µm using up to 100 kWh/t less energy than could be achieved by wet ball milling. Using conventional comminution, an ore might require grinding to p80 = 45µm (? 325 mesh), for example, to liberate the valuable components, e.g. magnetite, from gangue, e.g. silica. Inter-particle comminution in HPGR may break some ores along grain boundaries thereby liberating valuable minerals from gangue at a much coarser particle sizes. Early magnetic separation rejection of silica gangue liberated from magnetite by HPGR at coarser grain sizes could further reduce downstream comminution energy consumption.

Jan 1, 2009

By S. Ling, T. Liu, Y. Shang

A new copper-molybdenum flotation technology developed for a certain coppermolybdenum ore is introduced. We achieved copper-molybdenum bulk flotation in lowalkali conditions. Locked-circuit test results showed that the bulk concentrate contained 21.05% Cu and 1.10% Mo, with copper recovery of 87.37% and molybdenum recovery of 77.07%. For the copper–molybdenum separation process of the bulk concentrate, we use a new depressant, BK511, to replace the traditional sodium hydrosulfide. We achieved copper–molybdenum separation through one rougher, nine cleaner, and two scavenger processes. The results of locked-circuit tests showed that the molybdenum concentrate contained 46.19% Mo and 0.75% Cu, with molybdenum recovery of 93.80%; the copper concentrate contained 21.50% Cu and 0.069% Mo, with copper recovery of 99.92%. This new technology overcomes disadvantages of using large amounts of lime, sodium hydrosulfide, and other reagents in traditional copper–molybdenum flotation.

Jan 1, 2023

By B. P. Gilbertson

In her wonderful book, 'The Guns of August', historian Barbara Tuchman tells us that the French war plan for 1914 was dedicated entirely to an offensive strategy, not a defensive one. Plan 17, as it was called, concentrated everything on a French advance to the Rhine, leaving the French left virtually unguarded. This strategy could only be justified by the fixed belief that the Germans could not deploy sufficient manpower to extend their invasion around through western Belgium and the low provinces; and this in turn was based on the belief that the Germans would never use reserve troops in the front line. Al evidence to the contrary was ignored. But when the war came, the Germans followed Count Von Schlieffen's plan; they did use reserves in the front line and they did come the long way around on the west. The result- as you know-was a protracted war, with fearful consequences for the rest of our century.

Jan 1, 1994

By A. Bascetin

One very important aspect of mining is deciding what material in a deposit is worth mining and processing, versus what material should be considered waste. This decision is summarized by the cut-off grade policy. The cut-off grade strategy for an open pit mine influences the annual cash flows and affects the net present value of a project. The optimization of cut-off grade strategy requires the knowledge of detailed operational costs, mining sequence, mining operation, processing, and product constraints, as well as the grade distribution of a given deposit defined by pit, phase, and different material types. Cut-off grade optimization algorithms have been developed in the past. The most common criteria used in cut-off grade optimization is to maximize the net present value (NPV). This paper describes the determination of a cut-off grade strategy based on Lane?s algorithm adding an optimization factor based on the generalized reduced gradient (GRG) algorithm to maximize the project?s NPV. The introduced algorithm is a windows based program developed at Virginia Tech that is based on a series of Visual Basic routines within a spreadsheet environment (Excel).The benefits of the methodology are demonstrated using a hypothetical case study. Keywords: Cut-off grade optimization, net present value maximization, generalized reduced gradient algorithm method.

Jan 1, 2007

By M. G. Atmore

As is usual when preparing for this type of occasion, I looked back at the subjects covered by my predecessors when they assumed the presidency of this Institute. You will appreciate that, in the eighty odd years since the Institute was founded, the diversity of subjects has been very great. In almost all cases it is quite natural that the speaker should have chosen a topic of special interest to him and one in which he was particularly knowledgeable.

Jan 1, 1979

By J. D. Koch

A 'project' is defined here as a process in which an idea is developed from its inception until either it is discarded or the product of the idea has been accepted by the ultimate user. The phases in a project, particularly the early phases, are examined, and project organization is described and contrasted with a functional line-management type of organization. Emphasis is placed on comprehensive definition, which is vitally important to the achievement of the goals of time, cost, and quality set for a project.

Jan 1, 1981

By D. L. Morrison

The School on the Accounting for Gold, which was organized under the auspices of The South African Institute of Mining and Metallurgy by Dr Hugh E. Bartlet, Consulting Metallurgist of Johannesburg Consolidated Investment Company Limited, was held at the South African Nature Conservation Centre at Delta Park, Johannesburg, on 15th to 17th May, 1989. It was attended by 178 delegates, including 2 from the OK and 4 from Zimbabwe. A total of 19 papers were presented covering the components of gold-accounting procedure, sampling techniques, and new sampling technology.

Jan 1, 1989

By D. J. Hallbom

A new graphical method termed the ?Design Curve Diagram? (DCD) has been developed to analyse non-Newtonian pipe flow data by relating the plastic Karman number to the plastic Reynolds number. Since the plastic Karman number is directly proportional to the pressure loss gradient and the plastic Reynolds number is directly proportional to the velocity, the DCD is essentially a non-dimensional pipe flow curve. This makes the DCD conceptually easier than the commonly used Hedström-Moody diagram. While, the DCD was developed for the analysis of yield plastic fluids (e.g., Bingham plastics), it is equally applicable to Newtonian fluids.

Jan 1, 2007

By K. R. Johnson

Changes in the pattern of computer systems for mine planning and geologic evaluation are occurring as a consequence of the introduction of 3-D high performance graphics terminals. The VULCAN system is described and an outline of its functionality is discussed. Increasingly, the integration of both database systems and graphics and databases will occur, allowing a greater degree of information access to mine operators. The system covers areas of database, drillhole graphics, mine design and layout, surface and solid modelling as well as reserve inventory generation. The design of the software is such that it is fairly commodity-independent and entirely menu-driven, to enable non computer-trained personnel easily to access the system.

Jan 1, 1987

By W. J. Cruise

This paper reports on a test that was conducted underground in a mine for two years on the following: pipes coated with paint, fusion-bonded powder, metal, or impregnated tape; and aluminium, stainless-steel, 3CR12, and plastic pipes. It was found that the degree of corrosivity and mechanical damage increases substantially from the shaft of a mine towards the stope. Thus, the range of coatings that can be used successfully is fairly large in the shaft and haulageways, but corrosion-resistant materials, especially corrosion-resistant steels, need to be used close to the stope. A study of the relative costs involved showed the costs of pipes of low-carbon steel and unplasticized polyvinyl chloride to be lowest, and those of epoxy-coated steel pipes to be highest.

Jan 1, 1985

By A. M. Milev

A simulated rockburst was conducted underground at Kopanang Mine, previously called Vaal Reefs No. 9 Shaft. The rockburst was simulated by means of a large blast detonated in solid rock close to a crosscut sidewall. The simulated rockburst involved the design of the seismic source, seismic observations in the near and far field, high-speed video filming, a study of rock mass conditions such as fractures, joints, rock strength etc. Knowledge of the site conditions before and after the simulated rockburst was also gained. Some of the important findings are listed below: ?Two areas of damage were identified on the blasting wall: (i) an area of high-intensity damage in which ground velocities of 3.3 m/s were recorded by an accelerometer, which was subsequently ejected in a block of rock, (ii) an area of low-intensity damage where ground velocities of 1.6 m/s were recorded by an accelerometer which remained on the tunnel wall. ?High-speed filming revealed rock fragments being ejected from the wall at velocities in the range of 0.6 m/s to 2.5 m/s. The measurements were taken in the area of low-intensity damage. As planned, no gas pressure was directly involved in damaging the wall of the tunnel. ?The attenuation of peak particle velocities for the main blast in the near field (6 m to 30 m), as a function of distance R, was found to be proportional to R-1.7. ?The simulated rockburst was recorded as a local magnitude ML= 1.3 by the Klerksdorp regional seismic network. ?Peak particle velocities from nearby blasting, recorded on the tunnel wall after the simulated rockburst, were about six times greater then peak particle velocities recorded from the same source area before the simulated rockburst.

Jan 1, 2001

By J. S. Freer

Two very successful schools on 'The design and operation of plants for the recovery of gold by activated carbon', were held from 14th to 18th October, 1985, and from 24th to 27th February, 1986, at Mintek. They were arranged by the Institute in close co-operation with Mr. Peter Bailey of Gencor, who was course leader. Computers and mathematics APCOM 87, the 20th International Symposium of the Application of Computers and Mathematics in the Mineral Industries, is to be held in Johannesburg from 19th to 23rd October, 1987. Interested people are invited to submit titles and synopses in any of the following topics or others. Papers can cover theoretical developments, practical applications, case studies, and software and hardware systems. Tunneling '88 The Institution of Mining and Metallurgy is pleased to announce the holding of 'Tunneling '88', the fifth international symposium and exhibition in the series, from 17th to 22nd April, 1988, at the Kensington Rainbow Exhibition Centre, London, England. Centenary exhibition and conference The major trade show to take place in the year of Johannesburg's centenary will be the 7th International Mining and Electrical Engineering Exhibition- ELECTRA MINING 86. The Exhibition, which is also the third-largest mining exhibition in the world, wil take place from 15th to 19th September, 1986, at the National Exhibition Centre, Crown Mines, Johannesburg. Mining electro technology The Eighth WVU International Mining Electro technology Conference is to be held in Morgantown, West Virginia, U.S.A., from 29th July to 1st August, 1986.

Jan 1, 1986

By M. Dworzanowski

The physical beneficiation of iron ore that has a wide particle-size distribution is problematic, regardless of the process applied, whether dense medium separation, gravity concentration, magnetic separation, or flotation. The problem of particle size is further compounded when there is a significant -10 µm fraction. Generally the approach to a wide particle-size distribution is to split into narrower size ranges and treat each separately. More often than not the -10 µm fraction is not treated but discarded. This approach results in a more complicated and expensive flow sheet and the loss of any potential value in the -10 µm fraction. Wet high-intensity magnetic separation (WHIMS) bench-scale test work was conducted on a haematite-rich material with a particle size of -200 µm. What made this material different was that it contained a 60% -10 µm fraction, hence discarding the -10 µm material was not an option. The objective of the test work was to determine how to maximize the recovery of the haematite across the full particle size range. Given the unusual particle size distribution, it was concluded that WHIMS would be the only practical beneficiation route. The -200 +10 µm and -10 µm fractions were treated separately and together under varying WHIMS conditions. For a given concentrate grade, the mass yield obtained was greater when the total particle-size distribution was treated. The inferred optimum conditions, using the same material, were tested on a pilot-scale WHIMS and similar results were obtained.

Jan 1, 2014

"Chairman: Professor B. W. MacKenzieRapporteur: Professor D. A. PretoriusPapers:Optimum spacing for soil sample traverses by W. A. HodgsonEvaluation of geochemical data by C. J. LenzResearch in oil exploration decision-making by J. W. Harbaugh and A. Prelat A drill hole data bank by M. R. AndertonOre reserve estimation and depletion planning for a beach diamond deposit by M. M. OosterveldIn opening the session, the Chairman indicated that the papers and discussions would revolve about quantitative methods of analysis and optimization of various aspects of exploration planning. The five papers would cover a wide range of topics within a general theme of exploration analysis, and it would be appropriate, therefore, to present the. papers as representing a sequential information-gathering process, namely, (i)geochemical and geophysical types of surveying for the location and identification of anomalous zones, (ii) tren¬ching and drilling of the anomalous zones found, and (iii) further refinement of the data for ore reserve calculations and production planning.The first paper, which was presented by Dr W. A. Hodgson, dealt with the optimum spacing between soil sample traverses conducted during geochemical prospecting. The theme of the paper was that the critical sampling interval should be based on the concept of element continuity, and that this interval could be determined by means of a correlogram. Ensuing discussion concerned the probability of the method, designed for areas where dispersion was high, working in localities where dispersion was either low or virtually non-existent. In the latter eases, specific orientation surveys for varying topographic, climatic and geological conditions would possibly be more useful than the preparation of correlograms. A further suggestion was made that cost versus risk should be taken into consideration when deciding upon the spacing between traverses. A balance could be struck by mathematical optimization. If the exploration budget was fixed, then the variance of risk could be minimized.The second paper was a short contribution by Mr C. J. Lenz. Computer-based plotting and evaluation of geochemical prospecting results were carried out because the low cost of analysis in Rhodesia permitted very large volumes of data to be accumulated in mass-coverage operations. Anomalous areas were demarcated within different environments by selecting probability or population boundary values from frequency distributions. In the short discussion which took place it was debated whether the method should be used only in the early high-risk stages of geochemical exploration and whether the introduction of geological bias could influence the actual results of an exploration program."

Jan 1, 2014

A diverse selection of rockbolt designs and resin anchors are available for use in underground mines. Research in recent years at the UNSW Mining Research Centre led to the construction of a rockbolt pull-testing facility. This facility has subsequently been upgraded, commissioned and initial test work has been completed to verify the pull-test process. A test program has been completed with the objective to understand the load transfer mechanism and improve the general performance of rockbolts. This paper describes the results of this research. Une sélection diverse de dessins du rockbolt et ancres de la résine est disponible pour usage dans les mines de métro. Faites des recherches ces dernières années à l'UNSW que le Centre de la Recherche Minier a mené à la construction d'une facilité de l'essai de la traction du rockbolt. Cette facilité a été améliorée par la suite, le travail de l'épreuve en commission et initial a été complété pour vérifier le processus de la traction-épreuve. Un programme de l'épreuve a été complété avec l'objectif comprendre le mécanisme du transfert de la charge et améliorer la performance générale de rockbolts. Ce papier décrit les résultats de cette recherche. Eine verschiedenartige Auswahl an rockbolt-Designs und Harzankern ist dafür verfügbar, benutzen Sie in unterirdischen Bergwerken. Forschung in letzten Jahren beim UNSW-Bergbau Forschung Zentrum führte Ruckerprobung-Einrichtung zur Konstruktion eines rockbolt. Diese Einrichtung ist anschließend befördert worden, ist beauftragt worden und wird abgezeichnet, prüfen Sie, die Arbeit ist vervollständigt worden, um den Ruckprüfung-Prozeß zu verifizieren. Ein Prüfungsprogramm ist mit dem Objektiv vervollständigt worden, den Lastübertragungsmechanismus zu verstehen und die allgemeine Aufführung von rockbolts zu verbessern. Dieses Papier beschreibt die Ergebnisse dieser Forschung.

Jan 1, 2003

By J. R. Menasce

Mechanization in low-stope panels situated in hard rock infers roof support by tensile bolting to allow free passage of trackless mining equipment in the production areas. This is in sharp contrast to conventional mining, where compressive roof supports?such as timber and grout packs?have traditionally been used, up to 1.5 metres from the production face. Bolting is a hazardous operation because material is dislodged from the roof during the drilling activity. Even with temporary roof support installed, small pieces of rock are dislodged by the percussive action of the drifter. Operations with the man situated directly under the drill, during the drilling activity, are hazardous. The only way to remove the hazard is to move the man away from the machine for as much as possible throughout the complete cycle Costs associated with safety cannot be quantified, but need to form part of the decision-making process. Machine selections based on purchase and running costs alone do not justify the investment cost of mechanized bolters. The equipment selection process needs to take into account the total cost of mining as well as the human safety impact and loss of production costs from having to re-bolt roofs in a production panel to prevent falls of ground. Labour costs in mechanized low-stope bolting are between one-quarter and half the labour costs of non-mechanized bolting. This paper reviews the mechanized bolting option versus handheld bolting from a mining process and cost perspective in a hard rock, low-stope room-and-pillar mining operation in the platinum and chrome industries.

Jan 1, 2006

By T. Tamura

It is known that the CaO-FetO-P2O5slag system has a wide liquid miscibility gap at steelmaking temperatures and this two-liquid slag phase has many advantages such as high activities of both FetO and CaO and high amount of P2O5. The phosphorus distribution ratio between the two-liquid slag and molten steel was confirmed to be higher than that between CaOsat.-FetO-P2O5slag and molten steel. The two-liquid slag may be useful for dephosphorization of molten steel and reduction of slag volume. Furthermore, the phase equilibrium of two-liquid CaO-FetO-P2O5slagsaturated with MgO was measured to determine the applicability of the two-liquid slag to dephosphorization in steelmaking process. Keywords: slag, refractories, solid solution, two-liquid phase, dephosphorization, steelmaking, phase equilibrium.

Jan 1, 2004

1. Mintek publications The folowing are available from Mintek (Private Bag X3015, Randburg, 2125 South Africa) at R35 (including GST) per copy to purchasers in South Africa and US$30 (including airmail postage) to purchasers elsewhere. Report M402 The preparation of synthetic fusion standards for use in the X-ray-fluorescence analysis of rocks and minerals, by RT. Eddy and J.J. Jacobs. Apr. 1990. 19 pp. Report M405 Slag-metal equilibria in the system Fe-Cr-Si-C-Ca-Mg-AI-O, by R.H. Eric and M. Akyizli. Aug. 1990. 29pp. Application Report no. 8 The development of a process for the recovery of gold from gold-bearing solutions by means of activated carbon or resin in a NIMCIX column. 1990. 19 pp. 2. New publications from Trans Tech The folowing are available from Trans Tech Publications Ltd, Old Post Road, Brookfield VT05036, USA. Efect of iron and silicon in aluminium and its aloys, edited by I. Kovacs. 1990. 450 pp. $124. Martensitic transformations, edited by B'.C. Muddle. 1990. 714 pp. $190. Ferites, edited by C.M. Srivastava. 1989. 2 vols. 1280 pp. $254. Properties and characterization of amorphous carbon films, edited by J.J. Pouch and S.A. Alterovitz. 1990. 714 pp. $152. Synthesis and properties of boron nitride, edited by J.J. Pouch and S.A. Alterovitz. 1990.426 pp. $192. Electronic structure and latice defects in aloys, edited by R. W. Siegel and F .E. Fujita. 1989. 320 pp. $78. 3. A new edition Tomorow's materials, by K.E. Easterling. London, The Institute of Metals (1 Carlton House Terace, London SWIY 5DB, England), 1990. 2nd ed. 170pp. US$29. 4. Books for exploration geologists The folowing books are obtainable from Elsevier Science Publishers, P .0. Box 211, 1000 AE Amsterdam, The Netherlands. Lateritic bauxites, by G. Bardossy and G.J.J. Aleva. 1990. 624 pp. DFL. 295. Platinum-group element exploration, by D.L. Buchanan. 1988. 186pp. DFL 150. Lead isotopes in mineral exploration, by B.L. Gulson. 1986. 246 pp. Dfl. 160. Prospecting and exploration of mineral deposits, by M. Kuzvart and M. B6hmer. DFL. 285. 5. Journal for earth scientists . Ore Geology Reviews, published by Elsevier Science Publishers, P.O. Box 211, 1000 AE Amsterdam, Netherlands. 6 issues per year. Annual subscription DFL 453 including postage.

Jan 1, 1990