Search Documents

By S. Schmachtel

Several possible physico-chemical properties of composite electrodes for oxygen evolution are presented to describe experimental data for which a mathematical model had been developed. On this basis, local electrical and electrochemical properties of a composite electrode were investigated with conductive atomic force microscopy (CAFM) and scanning electrochemical microscopy (SECM). It could be shown by CAFM measurement that the boundary between matrix and catalyst particles seemed to have special advantageous electrical properties. The SECM measurements showed the presence of mass transport phenomena with increased surface concentrations, whilst the thickness of the Nernst diffusion layer was very small. An intermediate was detected and assigned to be hydrogen peroxide. From all species involved in the oxygen evolution reaction (H2O2, H+ and O2), it was concluded that local active spots exist on the electrode on which hydrogen peroxide reacts to oxygen and protons. A two?step two-material process was suggested to explain the whole oxygen evolution mechanism.

Jan 1, 2008

By E. D. Musin, S. S. Gudkov, A. V. Epiforov, S. V. Balikov

The standard technology for processing of gold-bearing sulfide raw material has many problems associated with the use of cyanide as a gold lixiviant. Therefore, many tests to find alternative gold recovery methods are being undertaken. This paper describes some technological solutions, which can become alternatives to cyanide technology in the future. Pressure oxidation (POX) of refractory gold-bearing sulfide concentrates from five different Russian gold deposits were investigated. Concentrate 1 was gold-copper concentrate. Concentrate 2 was gold-pyrite concentrate. Concentrates 3-5 were pyrite-arsenopyrite double refractory concentrates. The POX tests were at temperatures of 110, 200 and 220 °C and oxygen pressures of 1.5, 2.4 and 3.0 MPa were carried out. Gold lixiviants, such as chloride, thiosulfate, sulfite and thiocyanate were tested. The recovery of gold from sulfide gold-bearing concentrates by non-cyanide methods was 97- 99%, and from double refractory concentrates, 86-93%. The tested reagents are less toxic than cyanide, and their use will reduce of the cost of gold production. These methods make it possible to recover gold in acidic media, and eliminate the washing operation and POX slurry neutralisation. In addition, precious metals recovery from POX cakes using lead reduction smelting was investigated. It was shown that the “POX-pyrometallurgical” technology for double refractory concentrates processing could be used with recoveries of gold and silver of 97 and 96%, respectively. Keywords: Recovery of gold, refractory sulfide gold-bearing concentrates, double refractory concentrates, pressure oxidation, non-cyanide lixiviants of gold, chloride autoclave leaching, thiosulfate leaching, thiocyanate leaching, sulfite leaching, reduction smelting, POX-pyrometallurgical technology

Jan 1, 2020

By M. Kerr

Background- History The most significant change in mining since the late 1970?s has been the emergence of very large scale mining operations , which have been developed to ensure profitability with relatively low grade ores. These large tonnage operations have resulted in the development of larger unit sized machines in all operations of beneficiation, solid-liquid separation and dewatering. Often only a few flotation lines are installed and tonnages up to 25 ktpd and beyond are not uncommon. The increased throughputs have led to the development of circular, reactor type tank designs. The reactor cell system is the most up to date flotation cell design to utilise the principles of circular cell design. The Svedala DV mechanism was specially developed to suit the RCS machine giving good solids handling characteristics and excellent metallurgical performance. Development of UG2 ore type flotation equipment The equipment was developed and optimised by Svedala process from 1995. A higher energy specification was requested by industry. This amounted to 3kW/m3 for installed volume. Existing designs were at 1.5kW/m3. Hence various modifications were required to achieve the required power input. The first 50m3 machines were installed and developed at Impala Platinum?s UG2 circuit over a one year period. Once reliability and performance was achieved, over 300 large volume flotation cells were installed at Anglo Platinum and Lonmin operations as well. Pilot Plant Development The Impala Platinum High Energy pilot plant was commissioned in 2002 and had an installed power exceeding 5kW/m3. It was operated for over a year at the tailings dam booster station and was fundamental to the large scale scavenging plant design. All experience in overcoming mechanical and operational problems was applied in scale up design principles. A very robust mechanism was designed to accommodate the additional power input from installed motors, as well as the high SG (>1.5) of the feed source. The pilot plant flowsheet is shown in the figure below.

Jan 1, 2007

This paper presents an initial investigation into the viability of co-kriging the grades of multiple mining cuts in a two dimensional, thin reef scenario. Deposits with gradational mineralized zones, in the perpendicular sense, are not as well served by the use of reef accumulation and thickness as deposits characterized by a sharp distinction between ore and waste rock. South African Bushveld Complex platinum deposits and Witwatersrand gold deposits are examples of this distinction. The calculation of an optimal mining cut is of paramount importance in the mining of Bushveld platinum. Two-dimensional kriging of a constant stoping width mining cut is an effective method for resource calculations once a cut is decided, but this begs the question of how to decide on the cut. Comparison of multiple cuts is used as a way of achieving this decision on many of Anglo Platinum’s operations. Although the kriging of each cut is valid in isolation, occasional negative values occur when incremental grades between overlapping cuts are calculated. Negative incremental grades cannot reflect reality. They are thought to be related to the inability of the method to include the strong continuity in the perpendicular direction demonstrated by the relevant variograms. Co-kriging of related variables has been investigated as a potential means tore impose this inherent order relationship. Various co-kriging options have been investigated. The method has been tested on a real data set from an established platinum operation. One of three types of anomaly has been investigated so far. The results show that co-kriging the mining cut grade as the primary variable, with just one secondary variable, the reef thickness, eliminates most occurrences. Severe anomalies remaining are arguably indicative of population mixing and might be more effectively treated by rezoning the data. Aim—To investigate the viability of co-kriging the grades of multiple mining cuts as a method for resolving anomalies in the estimation of such cuts on Bushveld platinum deposits, with applicability to other thin reef type deposits with a gradational not sharp cut-off between ore and waste in the direction perpendicular to the reef. Keywords: co-kriging, cross variograms, ordinary kriging, platinum, two-dimensional, grade profile

Jan 1, 2003

By R. Katzenbach, M. Vogler, U. Adamietz

Abstract The design of deep excavation pits in rock mass is dependent as well on the mechanical properties of the rock mass as for example the orientation and the type of discontinuities like bedding planes, joints and fissures, the length of the discontinuities (persistence), the grade of weathering, the strength of rock mass, and the shear strength in the discontinuities, etc., and also on the respective boundary conditions specific for the project, and here especially the geometrical boundary conditions. The basic mutual influences and interactions between these boundary conditions are explained and exemplary presented at an excavation pit with a depth of 18,5 m, situated at a slope with a surface near groundwater table. Résumé La planification des excavations profondes dépend aussi bien de la qualité mécanique du roc, par exemple la location de la texture de la surface de moindre résistance, le degré de rupture, le degré de décomposition, la dureté du roc et la résistance limitée au cisaillement de la texture de la surface de moindre résistance que des conditions limitées spécifiques pour le projet, ici en particulier des conditions limitées géométriques. Les influences et interactions essentielles et mutuelles entre les conditions limitées isolées seront expliquées et présentées à l’aide d’une excavation 18,5 m de profondeur, située sur une pente où le niveau des eaux souterraines est près de la surface. Kurzfassung Die Planung tiefer Baugruben im Fels hängt sowohl von den mechanischen Eigenschaften des Fels wie z.B. der räumlichen Lage des Trennflächengefüges, dem Durchtrennungsgrad, dem Verwitterungsgrad, der Gesteinsfestigkeit sowie der Scherfestigkeit des Trennflächengefüges als auch von den projektspezifischen Randbedingungen hier insbesondere von den geometrischen Randbedingungen ab. Die wesentlichen gegenseitigen Einflüsse und Interaktionen zwischen den einzelnen Randbedingungen werden aufgezeigt und an einer 18,5 m tiefen Baugrube in Hanglage mit oberflächennahem Grundwasser vorgestellt.

Jan 1, 2003

By D. vas As, Constance M. Vleggaar, P. D. Toens

A facility at the National Nuclear Research Centre, Pelindaba, for the calibration of gamma survey meters used in uranium-prospecting operations by P. D. TOENS, D.Sc. (Fellow), D. van ASt, M.Sc. (Visitor), and CONSTANCE M. VLEGGAAR, B.Se. (Visitor) Ground radiometric surveys in uranium prospecting have in the past suffered from two serious shortcomings. Owing to varying instrument sensitivity and the often arbitrary height at which readings are taken, it has been impossible to compare results obtained in different surveys and, moreover, to relate such readings to actual U30s concentrations. A set of calibration sources designed to overcome these problems has recently been constructed on the site of the National Nuclear Research Centre, Pelindaba. A discussion of the standards applied and the instrument calibration procedure is presented.

By M. J. U. T. Van Wijngaarden, R. J. Dippenaar

An electrochemical technique based on the solid oxide galvanic cel Mo / Mo + MoO2/ ZrO2-MgO / Fe + (FexO)slag + Ag / Fe was used in a determination of FexO activities in liquid slag systems. The emf measurements, scanning electron microscopy, and microprobe analysis of the cross-sections of the electrolyte tubes used in direct contact with the slag melts indicated that slag attack did not affect the open-circuit emf values during normal cell operation, The reliability of the cell was confirmed by the good agreement between the standard free energy of formation of liquid Fep obtained in the present study and those reported in the literature, The FexO activities were determined in FexO -CaO and FexO-SiO2 slags at 1673 K, and are in good agreement with those measured by the conventional gas-equilibrium technique. The experimental technique was successfully extended to the measurement of Fe2O activities in the complex slags that are used for the external desilliconization of the hot metal product of the blast furnace.

Jan 1, 1986

By W. P. Nel

A fuel cell is an electrochemical engine that converts the chemical energy of a fuel, such as hydrogen, and an oxidant, such as oxygen, directly into electricity. The emerging fuel cell industry may represent a major opportunity for the global platinum mining industry. This is because low temperature fuel cell systems use platinum group metals as catalysts. Fuel cell vehicles may become the most important driver of future platinum demand within years of their commercialization. A great number of factors impact on and drive the diffusion of fuel cell vehicle innovation. Such drivers range from energy security to environmental concerns and the technological development of fuel cells and systems. Such factors and drivers of fuel cell vehicle diffusion are combined with the generic ?body of knowledge? on ?technology forecasting? and ?diffusion of innovation? to design a framework that provides a holistic approach to the analysis of this complex enterprise. An attempt is made in this paper to address the following questions: Which types of fuel cells require platinum group metals? Which types of fuel cells will achieve dominant design status? Will fuel cell vehicles diffuse successfully? How big will the impact of successful fuel cell vehicle diffusion be on future platinum demand? How well do fuel cell vehicles compete with incumbent technologies such as spark-ignited and compression-ignited internal combustion engine-driven vehicles? How soon will oil depletion start to drive the diffusion of fuel cell vehicles? How important is hydrogen as a fuel? What impact does the inadequate hydrogen fuelling infrastructure have on fuel cell vehicle diffusion? The paper contains some initial results of a research project that has the aim of producing a schedule of future platinum demand generated from fuel cell vehicles. Keywords: diffusion of fuel cell vehicles, technology forecasting, platinum demand forecasting.

Jan 1, 2004

By L. G. Stolarczyk, J. Duncan

"SynopsisLong before the environmental movement, coal miners were suffering from occupational diseases that became apparent in the later years of service, and especially during the retirement years. Chronic exposure to micro-fine dust in the respirable range (‘float’ dust) causes various lung diseases, referred to as coal mine dust lung disease. In the USA alone, 76 000 miners have died of coal mine dust lung disease since early legislation recognized the issue in 1969. Researchers believe that reducing float dust exposure limits alone will not reverse the increasing incidence of coal mine dust lung disease seen in the current generation of miners. Trace and radioactive metals are concentrated in the thin boundary layers of the coal seam (Roberts, 2013), and hence float dust includes silica and toxic trace metals. The production and quality of coal is also significantly impacted by the presence of these contaminants in the coal. In the combustion process, the trace metals are oxidized and become incorporated in the fly ash and flue gas. Since they are extremely water-soluble, they represent a significant danger to health and the environment. Coal preparation plants and power stations need to mitigate these contaminants as far as is practical, but the simple fact is that most contaminants should have been left un-mined.This paper describes an innovative coal-cutting solution to the longstanding technology gap in mining – the ability to measure uncut coal layer thickness to the boundary rock layer. Because of constant changes in geology, seam thickness, and seam undulation, the horizon sensor must be located in the bit-block of the rotating cutter drum of the mining machine. Contaminants in ROM coal must be minimized at the source – that is, at the rock/coal crushing cone directly under the bit-tips of the cutting drum. Bittip distances to the rock boundary layer must be automatically controlled in real time when mining in a complex and undulating coal bed. Horizon sensing (HS) technology enables the mining machine’s cutting picks to stop at a specified distance from undulating horizons of the boundary rock. The thin contaminated coal layer can be left in situ, significantly reducing the toxicity of the float dust. Preventing the metal picks from striking quartz-containing boundary rock also reduces the occurrence of methane ignitions. HS technology equipped with pick force vector sensing can allow optimization of the cutting pick lacing pattern for minimum coal and rock crushing, thereby reducing float dust. This technology may enable the mining industry to convert from automated machine control to autonomous during coal cutting and loading."

Jan 1, 2015

By C. Dixon

This paper is based on the assumption of some knowledge of the National Water Act. It will consider the question of how that Act fits in with: a) existing laws which overlap on the subject matter b) new laws either in draft or in the process of being compiled c) policies which will eventually find their provisions included in new legislation (e.g. minerals policy) d) international practices. The focus will be specifically on the interaction of legislation relating to water use and water pollution in the mining sector as well as the role of the Department of Water Affairs in mining matters. Hence the title of the presentation.

Jan 1, 1999

By J. J. Bezuidenhout

The waste-heat boiler is used within the Sulphide flash smelting process as the main dust and energy recovery unit. The large volume of off-gas discharged from the flash smelter is at a very high temperature (1350°C) and contains a significant dust load that subjects the downstream waste-heat boiler to tough and demanding conditions. The boiler cavity is especially prone to dust accretions, fouling, and corrosion caused by accumulation of molten particles and precipitation of sulphuric acid. Computational fluid dynamics (CFD) is applied within a qualitative study to model the flow and heat transfer distribution throughout the waste-heat boiler. The commercial CFD package, Fluent 6.2.16, was applied to a modified waste-heat boiler (23 m ×11 m ×5.4 m) within the Outokumpu flash smelting process. This investigation focuses on the geometric modifications to the typical boiler design, which includes elevation of the ceiling, placement of flow-obstructing baffles and radiation plates parallel within the flow path. Also investigated were various boiler operating conditions such as the circulation of process off-gas, air leakage from the dust discharging hoppers and variation in inlet gas composition. The geometric modifications had the desired effect of increasing the volumetric utilization and therefore enhancing heat transfer between the boiler surface and the gas stream and dust segregation. Introducing circulated off-gas at a rate of 20 m/s and at a 45° angle to the front of the waste boiler further enhanced cooling while reducing the high impact of the furnace-uptake gas-stream on the boiler ceiling. The placement of radiation plates was found to be very effective in enhancing the heat transfer surface and distributing gas flow within the boiler. These results present recommendations towards an improved waste-heat boiler design. Keywords: flash smelting, waste-heat boiler, CFD simulation, off-gas cooling.

Jan 1, 2008

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-technological cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and the introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-techno-logical cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

By André de Jager, Henk Ludik

Navachab Mine experiences difficulties with pit wall stability in certain areas of the mine. The main reason for the instability is the fact that the geology comprises many joints and faults. Blasting, without impacting negatively on the stability of the pit walls, poses a major challenge. The mine has installed a technologically advanced seismic monitoring system with monitoring sensors positioned at various locations and depths throughout the pit. The electronic data recording system records all relevant information on a continuous basis with early warning signals in cases of potential danger. From the information recorded by this micro-seismic system it was established that the energy release into the high-wall is predominantly influenced by the mining rate, water content and mining tempo and to a lesser extent by the blasting operations. To limit the negative effects of blast vibrations, the use of Electronic Delay Detonators (EDDs) was introduced. The optimal delays were determined through signature trace analysis. The vibrations obtained during blasts initiated by means of electronic delay detonators were monitored and compared to those traditionally obtained when standard pyrotechnic delay detonators had been used. The measured vibration data indicated an improvement of 25% to 100% drop in vibration amplitude compared. The accuracy and programmability of EDDs presented huge potential for blast optimization in terms of limiting the vibrations without compromising fragmentation. The whole project was conducted over a twelve week period with some 4000 EDDs. The average size of a blast was in the order of 350 holes using about 40kg explosives per hole, which equates to 14,000 kg explosives over 12 different blasts. The paper deals in detail with the blast optimization process with regard to: - determining the rock response time; - establishing the signature traces; - analyzing the wave interference patterns; - predicting the direction of constructive and destructive wave interferences; - optimizing of the inter-hole and inter-row delay periods; - measuring the ground vibrations. The results obtained during electronic blasting are compared to those obtained during pyrotechnic blasting. Comparisons are being made with regard to the following: - ground vibration measurements; - pit wall stability measurements; - blast safety.

Jan 1, 2006

By P. Maais

This paper gives an account of the development of a plant for the differential flotation of mixed sulphide ore, special reference being made to the separation of copper and zinc sulphides. The uniqueness of the geology, mineralogy, and metallurgy of each complex ore-body is stressed. Consideration is given to the scale-up of laboratory data, and to some of the factors involved in the design of milling and flotation plants for this type of ore. Process control and development are discussed, as are the human requirements for the optimum operation of a concentrator.

Jan 1, 1980

The compilation of the sampling nomogram is an essential tool in the optimization of a sampling protocol and allows the operator to track the change in relative variance of the sampling error (the Fundamental Sampling Error) during steps of comminution and mass reduction in the process of recovery of the aliquot for analysis. The data required for the compilation of the nomogram are centered on the sampling constant K and the exponent, alpha (a), of the nominal fragment size. Five methods for establishing K have been identified, but two of them, the duplicate sampling analysis (DSA) method and the heterogeneity test (HT) method purport to provide such a constant. The step by step procedure for each of these two methods was examined using broken ores from three mines, Mponeng mine, Kloof mine and Lily mine. Two of these mines (Mponengand Kloof) are typical Witwatersrand-type gold mines, while the third is an Archaean-type, shear related gold deposit situated in the Barberton Greenstone belt. The results suggest that the factor K derived using the heterogeneity test is very accurate, but applies only to a single size fraction in the spectrum of comminuted materials. The calculation of gold grain sizes using this method appears to be too small and does not conform with the results from detailed mineralogical studies. The factors K and alpha derived using the duplicate series analysis, are appropriate for use across a wide spectrum of comminution sizes and also provide realistic gold grain sizes, comparable with the equivalent circular diameter of gold grains identified in mineralogical studies of the ores.

Jan 1, 2009

By A. C. du Preez

Mintek has been involved in extensive test work since the early 1990s on the recovery of nickel and cobalt from leach liquors saturated in calcium, using synergistic solvent extraction systems. During this period the Nicksyn? reagent was developed, optimized, commercially manufactured, and tested by Tati Nickel on a demonstration plant for more than 2800 operating hours. Efficient recovery of nickel without the co-extraction of calcium, thus avoiding gypsum formation in the extraction and stripping circuits, was illustrated. This synergistic system was recently evaluated on a laboratory scale for the recovery of nickel and cobalt from synthetic lateritic sulphate leach liquor containing about 3 g/L nickel, 0.5 g/L cobalt, 0.7 g/L manganese, 20 g/L magnesium, and with calcium at saturation. Extraction and stripping parameters were determined for this feed liquor and are discussed in this paper.

Jan 1, 2014

By R. S. J. Toit

Discussion: T. L. Gibbs,* (Honorary Vice-President and Fellow): In terms of the Pneumoconiosis Compensation Act of 1962, a Pneumoconiosis Risk Committee was established whose function it is to estimate (by whatever means the committee deems fit) in respect of every controlled mine the pneumoconiosis risk to which persons employed in a dusty atmosphere at that mine are exposed. In estimating such risk the committee may estimate different risks in respect of individual mines or parts of mines or classes or groups of mines or occupations or localities at mines. The pneumoconiosis risk may be reviewed and re-estimated at any time. The Act provides further that the General Council for Pneumoconiosis Compensation shall apportion the levy imposed on owners of controlled mines on the basis of the pneumoconiosis risk determined by the risk committee and the numbers of persons employed in a dusty atmosphere. The task of the risk committee is a most responsible one and also a very difficult and complex one in view of the many different types of mines, rock formations, dust conditions, etc. Quite obviously, comparisons between mines cannot be made on dust concentrations alone as different mineral dusts have different toxicity or pneumoconiosis response factors. However, with its present knowledge, the risk committee is satisfied that the risk at mines, other than coal mines, is related to the mean quartz-equivalent dust concentration to which persons are exposed and the estimation of risks is based on this relationship. From the above, it will be clear that the work done by Dr du Toit on the problem of basing the current rate of levies to provide for pneumoconiosis compensation on the current dust hazard at mines has been of immense value to the risk committee. Up to now the risk committee has not been able to obtain complete and accurate information on the dust exposure of persons at all mines - and, in fact, it is doubtful whether it will be economic or practicable to obtain this in the foreseeable future - but reasonable assessments have been possible from routine dust sampling in some cases and from periodic comprehensive dust surveys in others. As a temporary measure the risks of some mines were estimated initially on a group basis relating to average dust conditions and the type of rock and mineral mined, but as more information became available, differentiation between individual mines became possible. It is the aim of the risk committee to eventually apply such a differentiation in all cases and to ensure that within the bounds of practicability each mine pays for its risk and for its risk only. In this connection, the relationship between the levies and the amounts actually paid out in compensation are examined regularly. In conclusion, I wish to add my congratulations to the author on his excellent paper. His findings will assist materially in the just administration of that very important piece of beneficial legislation, the Pneumoconiosis Compensation Act. G. K. Sluis Cremer MD (Visitor): Dr du Toit has made a valiant attempt to relate dust hazard and the rate of collecting funds for the purpose of paying compensation for Pneumoconiosis. In doing so he has had to make a number of assumptious, some of which touch on the medical aspects of pneumoconiosis. It is worth discussing whether these assumptions are justifiable. Pneumoconiosis is defined in our Pneumoconiosis Act as permanent disease of the cardio-respiratory organs which is caused by the inhalation of mineral dust. To a non-medical person this definition has probably a clear cut meaning. The doctors however have to deal with such conditions as silicosis and asbestosis where there is a well defined dose response relationship to the inhalation of quartz and asbestos respectively and on the other hand chronic bronchitis where the relationship to dust inhalation is poorly defined and where certainly no clear dose response relationship has emerged after many investigations in this country and overseas. Nevertheless since 1953 about half of our certifications for Pneumoconiosis are on the grounds of chronic bronchitis i.e. the X-rays show no evidence of silicosis, asbestosis or other relevant disease. This fact must affect Dr du Toit's computations. The next assumption we should examine is the manner in which toxicity factors have been allocated to the various mineral species. These allocations have in part been based on a restricted number of animal experiments carried out overseas but mostly in South Africa by Webster at the Pneumoconiosis Research Unit. To extrapolate the findings in a relatively small number of animal experiments to the expected reactious in man is a notoriously dangerous exercise. Furthermore the bracketing together of all silicates (except asbestos) and the insoluble metal oxides is entirely unacceptable. Talc (a hydrated silicate of magnesium) and muscovite mica (a silicate of aluminium and potassium) cause pneumoconiosis in their own right. On the other hand

Jan 3, 1970

By D. L. H. Bulbring

The removal of a cylindrical core from thick-wall sections for creep analysis by the relatively new Weldcore® process represents a very exciting methodology for obtaining more representative creep damage data from large engineering structures. The cylindrical core that is removed, representing about 60% of the wall thickness, leaves a substantial removal site that needs to be repaired. This paper presents data pertaining to taper Friction Hydro Pillar Processing as an alternative repair technique for filling the core removal site. Process parameters were evaluated with special attention being paid to the effect of downward force on process response variables, weld defects, and mechanical properties of 10CrMo910 steel. Process temperature and torque response as well as total process energy input were also considered. This paper also assesses the static and dynamic performance of this repair technique. The influence of a varying downward force and the occurrence and position of discontinuities were quantified. Downward force was shown to have the most notable effect on weld joint dynamic performance and was found to be related to the process temperatures achieved in close proximity to the weld interface.

Jan 1, 2013

By H. L. Zimba

Flotation involves the selective levitation of mineral and its transfer from cell to launder. The flotation rate is the rate of this transfer. It may be defined by the slope of a recovery-time curve for any cell in a bank or at any time in a batch operation. The objective in flotation rate study is an equation expressing the rate in terms of some measurable property of the pulp. This can be either the concentration of floatable mineral in weight per unit volume or a relative concentration, which will be a function of the recovery. A rate equation for an actual flotation pulp will contain at least two constants, both to be determined from the collected data. The data used in this paper were collected from bench-scale flotation tests on Konkola primary mill cyclone overflow at various pulp densities and pre-flotation thickener underflow at a pulp density of 35% solids by weight.

Jan 1, 2009