Search Documents

By J. Fu

"Since it was first identified in 1817, selenium has received considerable interest. Native selenium and a few selenium minerals were discovered several decades later. With the increasing number of selenium minerals, the occurrence of selenium minerals became the focus of much research. A great number of selenium deposits were reported all over the world, although few independent selenium deposits were discovered. Selenium is obtained mainly as a byproduct of other metals, and is produced primarily from the anode mud of copper refineries. This paper presents a comprehensive review of selenium minerals, as well as the treatment of copper refinery anode slimes for the recovery of selenium. Our focus is on the selenium minerals, including their discovery and occurrence, and the distribution of selenium resources. In addition, the main methods of recovering selenium from copper anode slimes are summarized. IntroductionSelenium (Se) was first observed in 1817 in a laboratory (Greenwood et al., 1984). The discovery of selenium was made by the Swedish chemist J.J. Berzelius and J.G. Gahn, who isolated selenium from a red residue in sulphuric acid from pyrite mined at Fahlun, Sweden. Selenium was named from the Greek word selene (moon), since it resembled tellurium, which had been discovered a few years earlier and named from the Latin word tellus (Earth).After the first observation of selenium in the laboratory, selenium received considerable interest. In 1954, E.P. Kaiser pointed out that Se is enriched in sulphide ores and often associated with Bi, Co, Sn etc. (Kaiser 1954). In 1959, Hawley and Nichol investigated selenium in Canadian sulphide minerals, and presented the content of selenium in sulphide from several deposits of different types. They also proposed that Se is enriched in lowtemperature hydrothermal pyrite (Hawley and Nichol, 1959). The thermodynamic conditions for forming native selenium and selenium minerals in sedimentary rocks were discussed, as well as geochemical behaviour of selenium near the oxidation zones of sulphides in the 1970s (Howard III, 1977; Zhu et al., 2003). Zhu et al. examined the morphology, features, and genesis of native selenium from Yutangba, Enshi City, Hubei Province, China in 2004, and pointed out, from the different forms of native Se, that selenium can be activated,transformed, remobilized, and enriched at sites such as in the unsaturated subsurface zone or in the saturated zone (Zhu et al., 2005). The transport and deposition of selenium in felsic volcanic-hosted massive sulphide deposits of the Yukon Territory, Canada was studied and reported by Layton- Matthews et al. (2005)."

Jan 1, 2016

By S. K. Murphy, S. M. Spottiswoode, A. M. Milev, D. Geyser

A portable, stand-alone instrument especially designed for recording strong ground motion was used in this study to create a large database of peak particle velocities measured underground. A total number of 39 sites located in stopes mining Carbon Leader and Ventersdorp Contact Reefs were investigated. Peak particle velocities whith values up to 3 m/s were recorded at some sites. The data recorded on the skin of the excavations were compared to the data recorded by the mine seismic networks to determine the site response. The maximum site response was obtained for source radii of between 5 m and 30 m and events locating within 200 m of the site. The extreme values of peak particle velocities were obtained in cases were the face-area lay within the source radius. Un instrument portable unique spécifiquement conçu pour enregistrer les mouvements dynamiques des terrains, a été utilisé dans cette étude pour créer une base de données importante sur la vélocité maximum des particules, mesurée en souterrain. Un nombre total de 39 sites situés dans les excavations exploitant les récifs appelés ‘Carbon Leader et Ventersdorp Contact Reefs’, a été investigué. Une vélocité maximale avec des valeurs allant jusqu’ à 3 m/s a été enregistrée sur certains sites. Les données enregistrées sur le bord de l’excavation ont été comparées aux données enregistrées par les réseaux séismiques de la mine pour déterminer la réponse du site. La réponse maximum du site a été obtenue pour des sources de rayons entre 5 m et 30 m et des évènements situés dans les 200 m du site. Les valeurs extrêmes de vélocités maximales ont été obtenues pour les cas où la zone de face se trouve à l’intérieur du rayon de la source. Ein mobiles, alleinstehendes Instrument, speziell entworfen um starke Formationsbewegungen aufzuzeichnen, wurde in dieser Studie verwendet um eine große Datenbank von Partikelspitzengeschwindigkeiten, die Untertage gemessen wurden, aufzuzeichnen. Eine Gesamtanzahl von 39 Aufstellungsorten in den Schichtabbauorten vom Carbon Leader und Ventersdorp Contact Reef wurden untersucht. Partikelspitzengeschwindigkeiten mit Werten bis zu 3 m/s wurden an einigen Standorten aufgezeichnet Die an der Oberfläche des Grubenraumes aufgezeichneten Daten wurden mit jenen Daten verglichen, die vom seismischen Netzwerk der Grube notiert wurden, um die örtliche Reaktion des Standortes zu bestimmen. Die maximale Standortreaktion wurde für Ursprungsradien von zwischen 5 m und 30 m erhalten und Ereignissen die sich innerhalb von 200 m vom Standort befanden. Die extremen Werte der Partikelhöchstgeschwindigkeiten wurdenin jenen Fällen erreicht wo sich der Abbaubereich innerhalb des Ursprungsradiuses befand.

Jan 1, 2003

1. Publications of the World Mining Congress Series A: Volume 5 World mining data '90. US$25. Series B: Volume 1 Chromite. US$31. 2. Randol publications The folowing publications are available from Randol International Ltd, P.D. Box 150632, Lakewood, CD80215, U.S.A.). Randol Gold Conference, Sacramento '89. 1990. 400 pp. $80. Randol mining directory 1990-1991. 1990. $100. Randol buyer's guide USA and Canada. 1990. $50. 3. New journal Industrial Metrology, edited by A. Choudry et al. Amsterdam, Elsevier Science Publishers, 1990. Dfl. 266 incl. postage for 4 issues per year. 4. Mintek reports The folowing reports are available from Mintek, Private Bag X3015, Randburg, 2125 South Africa. They are available at R35 (including GST) per copy to SouthAfrican addressees, and US$30 per copy (including airmail postage) to addressees elsewhere. Report M130D The application of a standard leaching procedure to tin-tungsten concentrates from Van Roois Vley deposit: Cross-cut bulk samples, by M.M. Fieberg and C.F.B. Coetzee. First issued 1984, reissued 1990. 11 pp. Report M160D The recovery of graphite from the Messina district, by R.N. Guest. First issued 1984, reissued 1990. 22 pp. Report M305D The beneficiation of nickel-copper ore from Uitkomst, by P.W. Dverbeek. First issued 1987, reissued 1990. 55 pp. Report M320D The flotation of pyrite from Bufe/sfontein Gold Mine, by A.M.R. Botelho de Sousa and V.E. Ross. First issued 1988, reissued 1990. Report M347D A utogenous miling of ore from the UG-2 Reef, by J.K.H. Lichter. First issued 1988, reissued 1990. 13 pp. Report M352D Fly ash as an adsorbent or precipitation agent in the removal of ionic species from solution, by C. Pohlandt-Watson, S.M. Graham, and K.F.G. Brackenbury. First issued 1988, reissued 1990. 9pp. Report M360D Beneficiation of limestone from Pienaars River, by R.N. Guest. First issued 1988, reissued 1990. 23 pp. Report M364D The recovery of gold from deposits in the Pilgrim's Rest area, by R.A. Burger. First issued 1988, reissued 1990. 15 pp. Report M396 Reduction of chromite spinels in iron-chromiumcarbon aloys, by R.H. Eric and E. Uslu. Mar. 1990. 33pp. 5. New review Diverless and deepwater technology. Advances in underwater technology, ocean science and ofshore engineering, edited by the Society for Underwater Technology. London, Graham & Trotman Limited, 1989.224 pp. £55.

Jan 1, 1990

Book review Pearson, J. S. Ocean floor mining. Park Ridge (New Jersey), Noyes Data Corporation, 1975. 201 pp. NIM reports Report no. 308 A mineralogical study of gold particles in pulp residues from the Bracken Gold Mine. (7th Mar.,1968. Re-issued Oct. 1975.) Report no. 377 Examination of pulp samples, treated with cyanide, for coated gold.(7th Aug., 1968. Reissued Oct.1975.) Report no. 385 The determination of the nature of coatings on gold particles. (2nd Aug., 1968. Reissued Oct. 1975.) Report no. 452 The Purlex Process - a description of the pilot plant leading to the use of the process in South Africa. (13th Jan., 1969. Re-issued Oct. 1975.) Report no. 482 Review of work on the treatment of pegmatites. (9th Apr., 1969. Reissued Sep. 1975.) Report no. 1443 Gravity concentration tests on four samples from Tantalite Valley,S. W.A. (5th Jul., 1972. Re-issued Sep. 1975.) Report no. 1489 The breakage of S oderberg electrodes. (10th Nov., 1972. Re-issued Nov. 1975.) Report no. 1545 A mineralogical investigation of leach residues from the Blyvooruitzicht Gold Mine. (22nd May, 1973. Re-issued Nov. 1975.) Report no. 1583 Preliminary tests on winnowing for the recovery of mica. (12th Nov., 1973. Re-issued Sep. 1975.) Report no. 1652 The identification of diamonds from Premier, Finsch, and Jagersfontein Mines by statistical analysis of data obtained from instrumental neutron-activation analysis. Report no. 1723 The determination of zirconium and aluminium in zirconiumaluminium alloys. Report no. 1739 The determination of trace amounts of noble metals in sulphate media. Report no. 1771 The determination of silver, selenium, tellurium, antimony, tin, lead, and arsenic in anode sludges. Report no. 1772 A study of copper recovery by lime roasting and leaching. Corrigendum The Special Issue of Volume 76 of the Journal ('Recent Advances in Mineral Dressing, October 1975) should be corrected as follows. The South African Institute Of Mining And Metallurgy - Information On Membershlp The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical, Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. Die Suid-Afrikaanse Instituut vir Mynbou en Metallurgie - Inligting Oor Lidmaatskap Die Instituut is in 1894 gestig as die Chemiese en MIetallurgiese Vereniging van ::!nid-Afrika. In 190-1is dit omvorm tot die Chemiese Metallurgiese en Mynbouvereniging van Sllid-Afrika en in 1956 het dit die Suid-Afrikaanse Instituut vir Mynbou en l\Ietallurgie geword.

Jan 2, 1976

By H. W. J. P. Neomagus, J. R. Bunt, T. S. Mthombo, C. A. Strydom

"Low-cost calcium lignosulphonate (CL), which is a byproduct of the wood pulping industry, was investigated as a potential binder during laboratoryscale pelletization of inertinite-rich high-ash coal fines from the Highveld Coalfield of South Africa. Coal-binder mixtures containing between 1 and 15% calcium lignosulphonate were prepared, pressed, and ultimate, proximate, porosity, XRD, and XRF analyses obtained. It was found that increased pressure during pelletization results in increased attractive forces, due to increased interparticle contact areas. FTIR analysis showed that chemical interactions occur between coal fines and the binder, as evidenced by the formation of new C-O ether-type bonds. The presence of moisture during pelletization enhanced surfactant activity of the binder. Chemical interactions between the coal and the binder seem to be mainly electrostatic, driven by Ca2+ from the calcium lignosulphonate, which may act as a bridge between the anionic parts of the binder and the surface of the coal. IntroductionCoal has over the years remained South Africa’s major energy source, with over 90% of the country’s electricity being produced via coal-fired processes (Arndt et al., 2016). Sasol’s coal conversion technology alone provides more than 40% of South Africa’s liquid fuel requirements (van Dyk, Keyser, and Coertzen, 2006). The production of high-grade coal requires the processing of run-of-mine (ROM) resources by a combination of processes which include crushing, screening, and washing (Radloff, Kirsten, and Anderson, 2003). These processes result in the generation of coal fines (< 0.5 mm) which, until recently, have been discarded into slimes dams (le Roux, Campbell, and Smit, 2012). Several issues are associated with slimes dams, among which are the costs of transportation of these fines from the place of origin to the discard point (often a considerable distance), and the potential environmental effects due to seepage of toxic materials into surrounding ecosystems (Clausen, 1973).Consequently, utilization of these coal fines is an area of great interest. Mechanical densification of fine coal by means of pelletization and/or briquetting to larger sizes for use in technologies that require lump coal, such as chain-grate stokers and fixed-bed gasifiers, has been shown not only to reduce environmental risks (Mangena et al., 2004), but also to significantly reduce storage and transportation costs (Mani et al., 2001). Pelletization is the process by which solid particles are consolidated into uniform, usually hard, impact-resistant agglomerates, rendering them useful as a fuel with sufficient calorific value for domestic and industrial utilization (Finney, Sharifi, and Swithenbank, 2009)."

Dec 1, 2018

By M. J. Kanda

"The design of rock slopes in the planning and operation of open pit mines and for road and rail cuttings requires the evaluation of their stability. This is commonly done using two well-established methods – limit equilibrium and numerical modelling. The research described in this paper compares the outputs of analyses using these two methods with regard to factor of safety and probability of failure, taking into account technical factors associated with each method and other factors such as material parameters and their variabilities. Results show that technical factors such as number of slices and slip circles, number and type of finite elements, and the stress reduction factor can all affect the results of stability analyses. Factors not taken into account in limit equilibrium analyses, such as dilation, in situ stress, and locked-in stresses can affect the outputs significantly. The research has focused particularly on the predicted location of the failure surface, the resulting volume of failure and, most significantly dependent on this volume, the predicted risk associated with slope failure. The results presented show that there is good agreement between the outputs of the two methods regarding factor of safety and probability of failure. However, the same is not the case with regard to volume of failure and hence risk, which can be very dependent on the methods of analysis and their input parameters. The research is not exhaustive, and there are many other factors that could affect the results of slope stability analyses that were not investigated. Some such factors are mentioned in the paper.IntroductionThe design of rock slopes in the planning and operation of open pit mines and for road and rail cuttings requires the evaluation of their stability. The traditional method of stability analysis used limit equilibrium (LE) methods, and this approach continues to be used. Numerical modelling (NM) packages are now also commonly used in slope stability analyses. The outputs from these analyses provide the factor of safety (FOS) and probability of failure (POF) of the slope. Since the capabilities of the two approaches are different, there can be some variations in FOS and POF outputs and in the predicted location of the failure surface. These variations can affect the predicted volume of failure, and this could in turn have a significant effect on the risk associated with the potential failure (Read and Stacey, 2009). Researchers such as Chiwaye and Stacey (2010) have found that LE analyses underestimate the predicted failure volume, unlike NM methods."

Jan 1, 2016

By W. J. Kempson

As a result of the rising electrical energy costs in South Africa, a method was sought to reduce the overall electrical consumption of typical shaft systems. A typical shaft configuration was analysed and the primary energy consumers were identified. The ventilation fans for this system were found to consume 15% of the total energy of the shaft system. It was calculated that more than 50% of this energy is consumed by the shaft itself, more specifically, by the pressure losses that occur in the shaft as the ventilation air passes through it. In order to ensure that the theory being used for the evaluation of these shaft systems is accurate, a total of five shafts were instrumented and the actual pressure losses over the shafts plotted against time. These shafts were then analysed from a theoretical perspective. Finally, in order to ensure a thorough understanding of the behaviour of the ventilation air in shaft systems, the systems were simulated using computational fluid dynamics (CFD) techniques. There were significant discrepancies between the theoretical analysis and the CFD simulation during the initial comparisons. This discrepancy lessened as the complexity of the CFD models increased, until when the complete shaft was modelled using the full bunton sets, the pipes, and the flanges, the difference between the theoretical evaluation and the CFD simulation was small. This result demonstrates that the theory is insufficient and that the interrelated effect of the buntons and fittings has not been fully appreciated by current theory. The final phase of the work presented here was to evaluate the costeffectiveness of using different bunton shapes and shaft configurations. It is shown that the increase in the pressure losses and therefore the direct operating costs of the shaft can vary by as much as 80%, depending on the bunton configuration chosen. The placement of the piping in the shaft can increase the pressure losses, and therefore the direct operating costs of the shaft, by as much as 12%, depending on the placement of the piping in the shaft; this effect includes the use of flanges. The use of fairings on a large cage can reduce the resistance that the cage offers to the ventilation flow by as much as 30%. This, however, does not translate into a direct saving because as the cage moves through the shaft, the overall effect is transitory. These savings can be significant when the items highlighted in this work are applied correctly. Keywords shaft design, ventilation, energy consumption, modelling, CFD.

Dec 1, 2013

By S. J. Ramokgopa

The development of the modern State and the growth of capitalism involves a complex process of interaction between cross-cutting structural dimension: first between politics and economics and, second, between market and hierarchy. Central to such developments are political economies of scale. Mineral specialization in the Third World developed within the framework of an international extension on oligopolistic structure of the advanced capitalist economies of Western Europe and North America. Up to the late 1960s, the world mineral and metallurgical industry was closely controlled by a handful of Western mining and industrial groups. To the extent that, foreign control of the mining sector was seen in the Third World producing countries both as the essence of foreign domination and as its major symbol. In some newly industrializing countries, the State took a more direct role in tying the economy and society together. Central to this process was the growth of large-scale finance capital. From early 1959to the mid-1970s, metal consumption in industrial countries expanded well beyond their domestic mineral endowments. And a free access to Third World minerals was a major element of the economic dynamism of these countries throughout that period. With the change in the characteristics of international investment, Africa has become less important as an outlet for capital exports of European countries. Actually, the African continent now receives only a very minor share of direct foreign investments of Western enterprises. International political economy is concerned first of all with the relationship between the economic and political domains across territorial boundaries. Second, attention should be drawn to the role of the State as the focus of decision-making in a system of competitive States, that is in turn, interdependent with a trans-national market economy in which mining and metallurgy are essential activities that affect the politics of the State, and how this in turn, rebounds on the politics of the international system. Understanding the role of the State must go beyond the glib pronouncements on the ?national interest?. How, and whose interest, the ?national interest? is determined, is precisely the problem. This implies a third theoretical problem that must be addressed: the linkage between the domestic and international domains (or levels of analysis), given that political-economic processes clearly cut across the lines of political decision-making constituted by the institutional structures of the State. Situating the State and economic interests within this vast ?state-society? complex that we call the global order will be a crucial problem for any theoretical approach that involves mining and metallurgy.

Jan 1, 2002

By A. C. du Preez

The separation of nickel and cobalt from calcium, magnesium and manganese by solvent extraction using synergistic mixtures of carboxylic acids was studied. Addition of certain viable synergists to commercially available tertiary branched carboxylic acids, such as Versatic 10 (Shell) or Neodecanoic acid (Exxon), produced large synergistic shifts (?pH50) in the pH50values for nickel, and small antagonistic shifts (negative ?pH50values) in the extraction of calcium. Under the initial test conditions used (0.50 M each of Neodecanoic acid and the Mintek synergist, in xylene) a large separation (pH50Ca? pH50Ni= 3.09 pH units) between nickel and calcium in their extraction from 1.00 M sodium nitrate solutions was obtained, compared with only 1.11 pH units in the absence of the synergist. The selectivity series for the extraction of divalent base metals from 0.333 M sodium sulphate solutions by 0.50 M Neodecanoic acid and 0.25 M of the Mintek synergist in C12-C13aliphatic diluent was found to lie in the order (with pH50values in parentheses): Cu(3.42) > Ni (5.08) > Zn (5.58) > Co (5.73) > Mn (6.62) > Ca (7.48) >Mg (8.25). In batch counter current experiments, a simulated leach liquor containing (in gL-1): Ni 5, Mg 5, Mn 2, Co 0.5, Ca 0.5, Cu 0.1and Zn 0.1 was contacted with the mixed extractant in three stages at unit phase ratio and an equilibrium pH of 5.9. The recovery of nickel was 99.9 per cent and that of cobalt was 84.7 per cent, whilst the co-extractions of manganese, calcium and magnesium were 2.7,1.5 and 0.04 per cent, respectively. The recovery of cobalt can be enhanced by employing a slightly higher pH, although this will also increase the extraction of manganese, calcium and magnesium somewhat. Nearly quantitative stripping (99 per cent) of nickel from the loaded organic phase was achieved in a single contact at an organic-to-aqueous phase ratio of 4 using a simulated spent electrolyte containing 39 gL-1sulphuric acid and 33 gL-1nickel,thereby producing an ?advance electrolyte? containing 57 gL-1nickelat pH 3.5. Loading of acid into the organic phase was very slight, amounting to only 0.002 M H+in contact with the above-mentioned spent electrolyte. Keywords: solvent extraction; synergism; nickel; calcium; carboxylic acids.

Jan 1, 2004

By B. Amadei, F. Tonon

Rock stress measurement is cast in the more general context of the determination of boundary conditions for rock engineering. A study on the effect of elastic anisotropy on underground excavations reveals that this effect is actually controlled by the imposed boundary conditions. Applications to tunneling and to the Underground Research Laboratory (URL), Canada, exemplify a procedure for boundary condition estimation formerly developed by the authors. The procedure displayed fast convergence despite the complex geometry, and the high degree of non-linearity of the models. In the URL application, the 3-D model was able to completely reproduce the complex measured stress pattern, and the 90° rotation of the principal in situ stresses with depth. In order to reliably estimate the boundary conditions reproducing the current in situ state of stress, response measurements of the rock mass to current disturbances are necessary as input data. La mesure des contraintes in situ tombe dans le domaine général de la détermination des conditions aux limites pour les problèmes de mécanique des roches. Une étude sur le rôle de l’anisotropie élastique sur les excavations souterraines montre que ce rôle est contrôlé par les conditions aux limites qui sont imposées. L’application aux tunnels et au Laboratoire Souterrain de Recherche (URL) au Canada, nous permet de présenter une méthode de détermination des conditions aux limites. La méthode converge rapidement bien que le géométrie soit complexe et que le problème soit non-linéaire. Pour le URL, le modèle 3D est capable de reproduire la distribution des contraintes qui ont été mesurées ainsi que la rotation de 90 degrés des contraintes in situ avec la profondeur. Afin de déterminer avec précision les conditions aux limites responsables pour la distribution actuelle des contraintes, la réponse du massif rocheux doit être connue et mesurée. In der Felsentechnik sind die Spannungsmessungen in Gestein an die Bestimmung der Randbedingungen gebunden. Eine Studie legt dar, dass der Effekt elastischer Anisotropie in unterirdischen Aushoehlungen von den Randbedingungen kontrolliert ist. Eine von den Authoren entwickelte Methode zur Bestimmung der Randbedingungen wird an Beispielen im Tunnelbau und im Underground Research Laboratory (URL) in Kanada illustriert. Auch bei komplexer Geometrie und einem hohen Grad an Nicht-Linearitaet zeigt diese Methode ein schnelles Konvergenzverhalten. Ein 3D-Model und dessen 90° Drehung der lokalen Hauptspannungen mit der Tiefe, kann bei einer URL Anwendung vollstaendig reproduziert werden. Um mit dieser Methode die Randbedingungen zuverlaessig abschaetzen zu koennen, werden der gegenwaertige lokale Spannungszustand sowie die Antwort des Gesteins und die resultierenden Stoerungen als Eingabedaten benoetigt.

Jan 1, 2003

By Kathryn C. Sole, Owen Tinkler

"Although the first large-scale application of copper recovery by solvent extraction (SX) took place in Zambia in the early 1970s, it is only in the last decade that this technology has become widely employed in this part of the world and is now a mainstay unit operation in most copper hydrometallurgical flowsheets. The mineralogy of the ores in the African Copper Belt, and hence the characteristics of the African leach liquors, differ significantly from those in Chile and the south-western USA, where copper SX has had a long and successful history. These differences provide operators, metallurgists, reagent vendors and engineers with many challenges: new approaches are needed to adapt this technology for successful implementation in this region. This paper examines typical operating practice in the African Copper Belt, discusses differences compared with other parts of the world and looks at some of the challenges and opportunities presented by these flowsheets. INTRODUCTION Following the success of the Rancher’s Bluebird and Bagdad solvent extraction and electrowinning (SX–EW) operations in Arizona in the late 1960s, the Tailings Leach Plant at Chingola, Zambia became the first large-scale copper SX plant in the world, commissioned in 1974. Despite the equipment design now being outdated, this plant still continues to operate successfully, indicating the versatility and adaptability of this technology. Today, there are some 75 copper SX operations worldwide with cathode production above 10 kt/a. The top ten producers currently account for some 40% of the global 4.3 Mt/a SX–EW copper production. South America (predominantly Chile and Peru) is the largest copper cathode-producing region, with annual production of some 2 Mt. The Central African Copper Belt (Zambia and the Democratic Republic of Congo (DRC)) is second, with cathode production of 1.2 Mt/a and North America (USA and Mexico) third, producing close to 0.8 Mt/a Cu (Cytec data, 2014). The remaining 0.35 Mt/a comes from all other regions combined (referred to as “Rest-of-World”). Current and future operations in Zambia and the DRC are summarised in Figure 1. The industry in this region is characterised by a large number of small (3 to 20 kt/a) plants, mainly Chinese-owned, and a few very large (>200 kt/a) operations, owned by major multinational corporations. This paper examines typical operating practice in the African Copper Belt, discusses the differences compared with other parts of the world and looks at some of the challenges presented by the conditions, as well as innovations in flowsheets, reagents and operating conditions that have been introduced in these circuits."

Jan 1, 2015

By W. Barnett

The Limpopo Metamorphic Belt is a complex geological terrane with at least three major deformational events. Tectonically juxtaposed lithology, open to isoclinal folding, crosscutting and re-activated shear zones and metamorphic gneisses and schists make pit slope design and maintenance a risky business. Venetia diamond mine?s Cut 3 is planned to reach 360 m by 2011. The difficult rockmass created problems in the original pit and a new more comprehensive slope design was necessary. Nearly 9 km of geotechnical drilling were undertaken to produce a new geological model and provide geotechnical information near the final Cut 3 face. All existing data from the pit were brought together into a database. SRK Consulting were brought into the project to audit the process and provide most of the manpower for the data analysis. Existing failures were back-analysed and the geotechnical domains identified. Analyses of only the southern domains are discussed in this paper. Geotechnical engineers can design slopes at any angle, but it is up to the managers at the mine to decide what risk they are willing to accept in a slope design. Once the issue of risk was discussed and settled in respect of the consequences of failure, each of the main geotechnical domains were analysed to produce a slope design at5% probability of failure with 15% above the first ramp. A risk assessment of the design was then undertaken to determine what risk the design placed on the equipment, personnel and the profitability of the overall mining operation. The risk assessment indicated minimal risk to the operation. One of the main assumptions of the final design is that the pit slopes will be dewatered. A project was immediately put in place to determine a groundwater model for the mine and to thereby determine the best dewatering procedure. However, it should be obvious that it is practically impossible to prevent benches from getting briefly saturated with water during storm conditions. It was therefore necessary to look specifically at supporting the crests of the ramps in the problematic southern domains to guard against the possibility of crest failure during heavy rains. The data available were re-analysed toward this objective. Spiles were recommended as the most cost-effective support system, and a probabilistic approach was used in the design. The final design has a 5% probability of failure, and the analyses indicate a strong sensitivity of the required spile spacing to the strength of the reinforcement material that will eventually be used. The pit slope parameters derived as per the discussion in this paper have just begun to be implemented at Venetia Mine.

Jan 1, 2001

By M. Shapiro, L. A. le Grange, B. Henning

Effective pyrometallurgical process vessel design requires accurate assessment of the heat fluxes through the walls of the furnace. This is particularly important for freeze lining operation which is designed to protect refractory materials exposed to chemically corrosive molten contents, or facilitate high temperature operation when the refractory materials are used at conditions close to their service limits. Numerical modelling of fluid flow and heat transfer in process vessels is often used to aid in the design of process vessels. Sophisticated models are used to analyse the three dimensional flow and heat transfer predicting the effects of electrical heating, magnetic stirring, buoyancy, shear forces, various cooling effects and ultimately heat fluxes at the walls of the furnace and refractory. Traditionally these models are applied to the separate single fluid systems in a vessel such as the freeboard region including the arc, the slag region and the metal bath. Boundary conditions such as shear forces and heat fluxes between connecting regions such as the slag and metal bath are either estimated or carried over from separate solutions. Shortcomings in these traditional approaches include the estimation of sometimes critical boundary conditions leading to unreliable heat flux calculations. Also when boundary conditions are carried over between solutions, the process is difficult to set up, time-consuming and finally not fully coupled. In this paper the definition and results of a fully integrated numerical model of a complete arc furnace are presented. The most important mechanisms acting in an arc furnace were considered, including the fields of electrical potential, current, magnetism, momentum, heat transfer and radiation. Temperature dependant properties included electrical conductivity, density, viscosity, and thermal conductivity. The geometry consists of the freeboard, the arc, slag, metal baths and different refractory regions. Although the combined model of air, slag and metal would be defined as a multi-phase problem it is not solved as such. Instead the different fluids are separated by sets of special solid baffles. These baffles allow the implicit transfer of current, magnetism, heat transfer and shear forces between the different fluids and disallow mixing of the separate fluids. The strengths of the integrated model are threefold: Firstly, it provides robustness in defining the geometry and boundary conditions for the overall model. Secondly, it provides the capability to switch on and off individual mechanisms such as buoyancy, magnetic stirring and shear forces in order to observe their individual importance. Finally, it provides a useful tool in the design process through its ability to obtain results of parameter changes in short time scales.

Jan 1, 2004

By C. Hutton

"SynopsisThe last commodities supercycle (2003 to 2011) was characterized by a belief in volume at any cost, where absolute output was deliberately prioritized over productivity considerations. This practice fuelled overoptimistic forecasting and planning, which in turn contributed to the economic crisis that followed. The sudden collapse of commodity prices has resulted in mining companies scrambling to find the right balance between optimizing current operations and preserving sufficient flexibility to grasp future opportunities. The runaway costs of building and operating mines have almost squeezed out profit margins, while lower ore grades are inflating production costs. Mining companies therefore need to look at the business with fresh eyes, and develop strategies to attract equity capital as traditional approaches are simply not working anymore. This is especially so in the context of a dwindling investor base that continues to demand greater returns, despite a significantly lower appetite for risk. This paper revisits the micro-economic concepts and demonstrates how pressure from shareholders to prioritize output contributed to spiralling costs and value destruction. Practical techniques are described to model cost curves to optimize a Mineral Resource endowment and address the need to rightbalance a business and preserve agility.IntroductionHenry Lazenby (2014) for the Mining Weekly writes, ‘Bruised and battered, the global mining industry today is undergoing a sea change. Practices and policies that might have worked wonders in the past are not as relevant today, and new approaches to running profitable mining operations need to be found.’ One significant practice the mining industry had during the last commodities supercycle (2003 to 2011) was chasing volume at any cost; absolute output was deliberately prioritized over productivity considerations (Goldsmith, 2013). Lazenby contends that in the face of falling and volatile commodity prices, many mining majors ‘across all commodity groups are currently grappling with sagging profits and low company valuations. This is often regarded as the result of the were in pursuit of growing their output at all costs in a high commodity price environment.’ Lee Hodgkinson, KPMG’s Canadian mining industry leader and quoted by Lazenby, says that ‘mining companies are now trying to find the right balance between optimizing current operations and preserving their agility to grasp future opportunities. The runaway costs of building and operating mines have almost squeezed out profit margins [whilst] lower grades of ore are inflating production costs. Mining companies need to look at the business with fresh eyes, and develop strategies to attract equity capital as it seems clear that some of the traditional approaches to the mining business are simply not working anymore."

Jan 1, 2015

By K. R. Koch

Although some of the platinum(II/IV) and rhodium(III) chemistry is considered ?old? and well-known, the application of modern multinuclear NMR spectroscopic methods to this chemistry in solution reveals new details about their rich and relevant solution chemistry. In this paper we will briefly illustrate that the highly-sensitive 195Pt NMR shielding is an excellent probe to explore aspects such as solvation, ion-pairing, and the hydrolysis chemistry of inter alia [PtCl6-n(H2O)n]n-2 (n=0-5). Moreover the novel use of 35Cl/37Cl and 18O isotopes effects as unique NMR ?fingerprints? leading to a new and unambiguous method of chemical speciation of the numerous possible PtII/IV and RhIII complexes present in halide-rich aqueous solutions. In the case of Rh(III) chemistry a new, direct speciation distribution diagram has been established for [RhCln(H2O)6-n]3-n complexes (n = 3-6) in HCl solution at 292 K with these methods.

Jan 1, 2012

By S. Andika, O. A. Putri

Maintaining fleet productivity, which consists of balancing loader and truck performance, has always been a challenging task. An automatic dispatching system (ADS) is implemented to help monitoring fleet condition and assign trucks to a designated loader. Integrated data from real time Global Positioning System, Vehicle Health Monitoring System, and other production related data are acquired to support the ADS. However, the abnormal truck cycle has been the main culprit which resulted in unnecessary loader hanging time and trucks queuing time. Hanging and queuing time accounted for 2.34 and 2.07 minutes respectively per loading cycle or equal to 2,861 loose cubic metres per fleet per day production losses. Using integrated dispatching system data, the authors conducted research to study a truck’s hauling cycle that affects fleet productivity. The data is modelled to obtain the arrival rate pattern in a front loading area by adopting the queue theory algorithm. This paper aims to understand the potential pattern of a truck’s cycle abnormality and to resolve its occurrence.

Sep 1, 2021

By T. Uysal

Various morphological parameters that affect the flotation recovery of sphalerite were modelled and optimized using the response surface method (RSM). The effects of roughness value, shape factor, and collector concentration were investigated using the central composite full design method. The results were evaluated by analysis of variance. The optimum roughening time was found to be 25minutes, the optimum roughness value was 2.9071 μm, and the optimum collector concentrationwas 0.001 M. Using these values, a flotation recovery of 98.01% was obtained. Similarly, in shapefactor studies, the optimum grinding time was 15 seconds, the optimum roundness value 0.7421, and the optimum collector concentration 0.0009 M, which resulted in a flotation recovery of 94.30%. The average error between the optimization results and the experimental results was estimated to be less than 6%, and the R2 values were greater than 90%. The study shows that RSM can be effectively applied in finding the economic optimum condition for obtaining maximum flotation recovery with minimum reagent consumption.

Sep 6, 2023

By R. Castro, R. Gómez, F. Betancourt, M. Moncada

In block cave mining, rock fragmentation is a key parameter that influences the production level design and mine planning. Fragmentation occurs mainly by natural breakage during the caving process and in the draw column. The breakage that occurs within the column is known as secondary fragmentation. Secondary fragmentation has been successfully described using the block caving comminution model, which replicates the fragmentation mechanics between particles under drawn and vertical loads in a draw column. This model is based on a kinetic and population balance approach, in which non-normalized and normalized assumptions can be used depending on material and comminution system behaviour. In this paper, the non-normalized and normalized approaches are applied and compared to laboratory data to determine which assumption should be used for secondary breakage in block caving. Approaches are compared graphically, with the mean square error and the Fisher test with a false-rejection probability of 0.05. Based on a statistical analysis, the results show that the normalized model can be applied to all the rock types tested.

Nov 1, 2021

The inherent weakness of the Zincor and similar iron removal processes is the relatively high undissolved zinc loss associated with the iron residue. High soluble zinc losses also occur due to poor filterability of the iron residue even though it may be limited to intermittent events. This work focussed on defining the optimum operating window for the Zincor iron removal process where iron is mainly removed in the form of amorphous, intermediate iron phases such as schwertmannite and ferrihydrite. In terms of the main operating conditions, optimum filterability was achieved under the following conditions: pH of 3.0, temperature as high as practically possible (70C), at least 25 kg/m3 seeding, and a retention time of at least 4 hours. When increasing the temperature from 60C to 70C, the required residence time decreased by almost 50%. Undissolved zinc loss was also reduced from 8% to between 2% and 3% by using a basic zinc sulphate/zinc oxide mixture as neutralising agent to effect iron removal.

Jan 1, 2003

By B. S. Spottiswoode

Lack of visibility makes it difficult for continuous miner (CM) operators to judge the desired sump depth. The resulting inaccuracies have proven to lead to significant production losses. This problem of measuring the depth of sump has been addressed in the past and a few measurement techniques have evolved. Despite various attempts, a suitable commercial depth of sump sensor does not yet exist. A system using the Doppler effect has been patented, developed and successfully tested. The method is non-intrusive and involves a beam of microwaves being projected obliquely at the roof. The received signal is analysed with respect to the transmitted signal, yielding the desired measure of displacement. Surface tests have revealed an accuracy of a few centimetres. Underground simulation tests on a load haulage dump (LHD) machine have verified the repeatability under the harsh conditions of interest. The system is presently being installed on a CM where it is to undergo a long-term performance evaluation. This paper presents the theory behind such a system, the hardware developed, the signal processing requirements and an analysis of the test results.

Sep 1, 2001