Search Documents

Lonmin, earlier than any other primary platinum producer, had to deal with the concentrating and smelting of UG2-rich ores and concentrates respectively. Smelting was performed at a fairly modest scale compared to the company's industry peers in the platinum group metals (PGMs) industry, and was focused on smelting concentrates obtained through low mass pulls while still maintaining high recoveries at its concentrators. Lonmin gradually smelted larger quantities of UG2 concentrates. Initially two 2.3 MW Infurnco furnaces were commissioned in 1982, followed by three 5 MW circular 3-electrode Pyromet furnaces in 1991. Deep electrode immersions and moderately high hearth power densities were used in all the designs. Lonmin decided to continue with circular furnace technology when it planned its new high-intensity No. 1 Furnace. Neither Lonmin nor the technology supplier and EPCM company foresaw the challenges that scale-up would bring when applied to the smelting of UG2-rich concentrate blends. Superimposed on the high chromite content, was the low base-metal loading, mineralogical difficulties, and fine particle size that resulted from milling of all concentrates (especially UG2 and recycle materials within the smelter). Through a process of fundamental diagnoses of furnace run-outs and wear patterns observed during repairs, the main challenges operating this high-intensity furnace were identified as sulphur vapour corrosion of the copper coolers, uneven and unpredicted movements of refractory bricks with associated copper cooler lift and matte tapblock movement, the formation of three-phase 'mushy' zones, high refractory and taphole wear rates, uncertainty in matte level and associated insufficient matte buffer height, and high furnace operating temperatures. These factors seldom worked in isolation and will be explored in more detail in the paper. The variability in furnace feed characteristics led Lonmin to redesign Furnace No. 1, to invest in backup furnace capacity, and to invest in improved monitoring and control. These improvements consisted of online and high-frequency off-line monitoring of feed chemistry and mineralogy, online pressure monitoring of water-cooled circuits, an alternative matte liquid level measurement in the furnace, and electrode immersion estimation. Improvements were also made at the converters by installing and utilizing optical spectral analysis of the converter flame to characterize converter behaviour and achieve the desired iron end-point for white matte. This paper also briefly discusses the current and future expansion plans, as well as ancillary operations at the smelter such as flue-gas handling and materials handling.

Jan 1, 2011

The Modified Zincex® Process, developed by Técnicas Reunidas, is highly flexible dealing with a wide range of pregnant leach solutions. No matter if those solutions are produced from primary or secondary raw materials, and/or are based on conventional leaching, pressure leaching, heap leaching or bio leaching the result is always high-purity zinc product. The zinc solvent extraction unit within the process is a very effective barrier for impurities and a buffer for the composition of the pregnant liquor. This unit achieves an extremely pure aqueous extract that can be converted into different final products. All of them are characterized by fulfilling the highest purity standards. Also, there is the possibility to adapt the global process to a wide range of pregnant liquor compositions and various production capacities up to a zinc production limit over 150 000 t/a with a single solvent extraction plant.

Jan 1, 2002

By I. Mihajlovic

This paper investigates a potential method for arsenic removal from copper concentrates using hypochlorite leaching. The problems concerning pyrometallurgical processing of copper concentrates with high arsenic contents are discussed. A possible solution to the problem by leaching of natural enargite crystals with sodium hypochlorite under alkaline oxidizing conditions, with enargite converted into crystalline CuO and the soluble arsenic forming AsO43-, was experimentally investigated and results are presented. Kinetic parameters were calculated for enargite leaching, using a model-free approach. Advanced isoconversional methods were used to investigate the dependence of activation energy (Ea) on reaction rate (a). Keywords Enargite, copper concentrate, isoconversional method, kinetics, activation energy.

Jan 1, 2011

By S. F. Böde, K. Böde

This paper focuses on developing a comprehensive and pragmatic information technology (IT) strategy for low-margin construction activities. This forms part of the realignment of the general business strategy, and refocusing the operational model. The main elements of the IT strategy formation are analysis of the current IT environment in terms of software and hardware, carrying out a gap analysis, and developing individual functional digitalisation strategies in construction execution based on Building Information Modelling (BIM), business administration processes, communication, business intelligence (BI) and reporting, and data security. Further, substantial emphasis is given to the sustainable strategy implementation in terms of hardware and software readjustments, their integration, user training, and defining the way forward.

Sep 1, 2021

By Antonio Karzulovic, Sergio Olavarría, Patricio Adriasola

The economical analyses of different Chuquicamata open pit mine planning scenarios, indicate that the pit closure should occur at latest in the year of 2017. However, about 60,000 m of drill holes have demonstrated that below the pit bottom there is a potential of 2.3 billion tons of ore. Hence, Division Codelco Norte developed the scoping engineering for a large underground panel caving operation, similar to El Teniente mine. This project considers the exploitation of a 2500 m 300 m footprint, with three 250 m lifts. The plan considers to initiate the construction in the year 2009, to begin the production in the year 2015 and achieve a production rate of 45 million tons per year in the year 2021. A large-scale transition from open pit to underground mining like this one presents three main challenges: (1) to include the geotechnical aspects relevant for mine design and mine planning, (2) to define the proper surface and underground infrastructure, and (3) to fulfil the project deadlines and to achieve the production targets. This paper summarizes this transition project and discusses these three main challenges.

Jan 1, 2006

By J. K. Pothal, S. Basu, R. Barik, P. K. Senapati, A. Dubey

The aim of this paper is to study the characteristics of limestone particles (size varies from 4 mm to 20 mm) during its transportation from open cast mines through pipes. The influence of four different size fractions of limestone samples (4–6 mm, 6–10 mm, 10–15 mm, and 15–20 mm) on pipe flow characteristics during vertical transport in a 100 mm NB hose pipe was investigated. The flow velocities in the vertically lifting pipe was varied from 0.95 m/s to 2.78 m/s and a rotary feeder of 2 to 4 tonne/hr. capacity was employed to feed the limestone samples to the lifting pipe. The pressure drop data for the different size fractions of limestone samples at different mixture velocities were analysed. The effect of input volume fraction and superficial velocity of limestone samples on hold-up ratio were discussed. It was indicated that there was no substantial increase in pressure drop of slurry samples in the studied range of concentrations (CW = 4.22% - 12.54%), particle size, and low to medium range mixture velocities with respect to water run head loss data. The hold-up for the larger size fractions (15–20 mm) of limestone samples was found to be significant as compared to smaller size fractions, which may be due to terminal settling velocities of individual fractions of the studied samples.

Mar 4, 2025

By L. A. Cramer

South African platinum mines produce the world?s majority of platinum metal that is used in autocatalysts and jewellery. As the platinum market is forecast to grow at healthy rates into the future, the South African producers, Anglo Platinum, Impala, Lonmin and Northam, are planning to expand in the next decade. Furthermore, a number of smaller producers who are accessing other mineral rights are entering the buoyant market. The South African platinum mines have traditionally exploited the Merensky Reef of the Bushveld Igneous Complex (BIC); however, the mining of this reef is reaching depths that require significant vertical shaft systems and costly refrigeration for access to the orebodies at deeper levels. In the past decade all of the producers have begun to mine the less attractive UG2 reef because of its cheaper mining costs. This UG2 reef contains significant quantities of chromite with typically a chrome-to-iron (Cr/Fe) ratio of 1.35. UG2 ores can contain between 10 and 25% Cr2O3dependingupon the reef width and the selected mining method. It is relatively cheap and easy to extract a portion of the chromite from a platinum concentrator tailings stream at a grade of between 40?42% Cr2O3. However, it is only in recent years that some ferrochrome producers have begun to source some of their chromite from the tailings of platinum producers. South Africa is also the world?s largest single producer of ferrochrome and supplies much of the world?s stainless steel producers and thus the growing market for their product. As the traditional sources of high Cr/Fe ratio ores have been depleted at the shallow economic depths and thus have become more expensive sources of chromite, technical developments have improved the ability to use fine chromite economically to make acceptable grades of ferrochrome. Thus UG2 fines are now becoming possible cheap sources of acceptable feed to the ferrochrome industry. The abundance of feedstock for ferrochrome production and the lessening dependence on mined material will impact upon the structure of the ferrochrome business in South Africa. With continued platinum mining from UG2 reefs, South Africa is set to remain highly competitive in the world?s ferrochrome/stainless steel industry.

Jan 1, 2004

By H. E. Bartlett

Previously, the grade of ore at the shaft head was taken to be equivalent to the grade measured in the faces by means of chip sampling. The tonnage mined from the stopes is determined from survey volumetric measurements. Estimates of shaft head grade and tons include the grades and tons of waste, development ore, sweepings from old areas, and other sources, not all of which are sampled. The tonnage of ore delivered at the shaft is often estimated using skip factors. These factors are subject to manipulation and not all the skips are filled to the same level. Consequently, both the grade and tonnage of ore delivered at shaft head are subject to a measure of uncertainty. For many years, these uncertainties have led to disputes between shaft managers and metallurgists over the reconciliation between shaft tons and grade and plant tons and grade. These problems are compounded when several shafts feed a central processing plant. Shaft bonuses and a shaft?s profitability are affected by poor gold allocation methods. Without measurement of the grade and tonnage from all shafts, a poorly performing shaft could benefit at the expense of the other shafts. In order to improve the measurement of grades and tonnage at the shaft head, which is the custody transfer point between the mine and surface operations, South African mining companies have developed a methodology to measure the mass of ore from each shaft using rail weighing equipment, and the run-of-mine grades delivered from each shaft using cross-stream (go-belt) sampling. Harmony Gold Mining Company has implemented the rail weighing and go-belt sampling methods for their shafts. This paper deals with the statistical tests on the procedures and control measures that are in place to establish confidence in the gold allocations. The metal accounting system for examining the allocations follows the first principle of the AMIRA P754 Metal Accounting Code of Practice namely ?The metal accounting system must be based on accurate measurements of mass and metal content. It must be based on a full check-in check-out system?. The check-in is mass and grade of run-of-mine ore and the check-outs are the plant input grades and the recovery and residue from the plant. The balances between check-in and check-out are the subject of the statistical analyses, which have been conducted using the classical statistical tests and procedures that are generally used in all fields of endeavour. It is concluded that the gold allocation procedures that rely on go-belt sampling and rail weighing of ore from shafts has been successfully implemented, and that the system, which has been in operation at Harmony since 1993, has won general acceptance from stakeholders, with the gold allocations being perceived as being fair to all. Apart from the on-mine issues of bonuses and fair allocations, accurate metal accounting assists in the broader issues of generating accurate production figures for management. An added benefit of weighing and sampling ore at the shaft head has been that shafts now have daily moving average grades, which are used for grade control. The go-belt sample at the shaft head is the first accurate sample of production in the value chain from face sampling to gold bullion. Keywords metal accounting, go-belt sampling, run-of-mine sampling, codes of practice, AMIRA P754, train weighing, statistical analysis, gold split, allocation of gold, metal balance, grade control.

Jan 1, 2014

By G. van den Berg

Anglo Platinum has initiated a project to investigate hydraulic hoisting technology for platinum mines. Hydraulic hoisting systems are categorized as pumping, fluidizing feeder or displacement feeder systems. Positive displacement piston diaphragm pumps are most suitable for pumping systems but they require that the ore be milled prior to pumping. Fluidizing feeders are unsuitable for platinum ore applications due to the large percentage of fines in the ore. The three-chamber pipe displacement feeder has been most widely used for hydraulic hoisting and is the most suitable technology for platinum mines. Eight hydraulic hoisting applications covering pumping and displacement feeder technologies are reviewed. The key factors to be assessed in selecting a hydraulic hoisting system for a platinum mine are discussed. A typical platinum mine configuration will comprise an ore preparation plant (to produce -15mm material through screening or crushing), motive water pump on surface, high pressure water pipeline from surface to underground, ore slurrification plant, three-chamber displacement feeder, and a high pressure slurry pipeline to surface. The water and slurry pipelines are housed in a purpose drilled borehole. A hydraulic hoisting system selection chart is presented. A 150mm diameter system with a 25 MPa pressure rating is required to hoist 60 000 t/m from a depth of 1 200 m. Generic capital and operating costs are presented. A major potential advantage of hydraulic hoisting is that the fines, which contain a high percentage of PGMs, are captured underground and transported directly to the concentrator. Hydraulic hoisting technology is ideally suited to providing supplementary hoisting capacity to existing shafts that have reached the skip hoisting capacity limit. The main advantage for new shafts is the potential to significantly simplify underground rock handling and transportation. All hydraulic hoisting system components are proven. The only risk area is the wear rates of the valves and piping. Current estimates are based on gold ore. The business cases investigated show that the financial viability of the installations are not sensitive to wear rate. Hydraulic hoisting is technically feasible and financially attractive for platinum mines. Keywords: hydraulic hoisting, slurry

Jan 1, 2005

By S. Ganguly, R. Kononov

Carbothermal reduction of manganese oxides and manganese ores in the solid state was studied in hydrogen, helium and argon at different temperatures, ore compositions and carbon to manganese oxide ratios. Wesselsore (South Africa) and two grades of the Groote Eylandt ore (Australia) with different level of impurities were examined. Ores were characterised by XRD, X-ray fluorescence, optical microscopy and scanning electronmicroscopy. Isothermal and temperature programmed carbothermal reduction experiments were conducted in a fixed bed reactor in a vertical tube furnace, with on-line monitoring of gas composition by the CO-CO2 infrared sensor. The reduced samples were characterised by XRD, SEM and LECO analyses. Extent of reduction was calculated using data on the off-gas composition, and LECO carbon and oxygen contents in the reduced sample. Manganese oxides in the ore were reduced to a-Mn and carbides Mn23C6 and Mn7C3 depending on the carbon to ore ratio. The reduction rate of manganese ores in hydrogen was higher than in helium and argon. Key words: Manganese, Carbothermal Reduction, Hydrogen, Argon, Carbon Monoxide, Helium, Kinetics.

Jan 1, 2007

By D. Bessinger, J. Rabe, J. Zietsman, C. Coetzee, P. H. Lamont, J. Muller

The UCAR® CHILL-KOTE? freeze lining concept combines wall cooling with carbon and graphite refractories of higher thermal conductivities to ?chill? the refractory lining by transferring heat from the refractory lining. Effective sidewall water cooling, together with the efficiency of the heat dissipating conductive refractories, lowers the temperature of the lining to below that of the molten process materials. This causes a layer of slag and process metal to solidify or ?freeze? and form a protective ?skull? which completely coats the refractory hot face. Once formed, the slag skull insulates the refractories, reducing heat loss and protect the lining from erosion, chemical attack, thermal shock, and other stresses. The result: extended life and greatly improved refractory performance. The Ilmenite smelting process depends on the presence of a solidified slag skull to protect sidewall refractory material from chemical attach by molten slag. No known refractory material is able to withstand this corrosive material. To date, UCAR has not applied their Chill Kote ? technology in the ilmenite smelting industry. This paper revolves around the results obtained from conducting an ilmenite smelting campaign on a 500kW DC open-arc furnace with a UCAR designed refractory system. The purpose of this test was to establish the effects such a lining has on refractory wear and the reduction-smelting process. Proper thermo-couple management enabled the authors to monitor lining wear for the duration of the campaign. Prior to the pilot-scale campaign, modeling work was completed to evaluate the feasibility of applying UCAR® CHILL-KOTE? technology to ilmenite smelting furnaces. The successful operation of a pilot-scale furnace equipped with the UCAR® CHILL-KOTE? lining as well as concise modeling suggest that it should be a viable option to consider for an industrial-scale furnace.

Jan 1, 2007

By N. N. Malila, N. R. Shoko

The ever-increasing pressure on the profit margins of ferro-chrome producers and the gradual depletion of deposits of rich hard lumpy chrome ores calls for the ferrochrome industry to maximise the use of fine fractions of concentrates and friable chromite ores. Zimbabwe is endowed with huge deposits of refractory and friable ores that occur on and off the Great Dyke complex. The conventional metallurgical process of smelting of chromite ores in submerged arc furnaces is favoured by the use of refractory hard lumpy ores. The requirement to use all lumpy ore has been circumvented to a large extent at Zimbabwe Alloys. The use of briquetted chrome ore fines in the production of Ferrosilicon Chrome and High Carbon Ferrochrome has yielded positive results over a period in excess of twenty-five years. Of the three industrially used methods of agglomeration of chromite ores; sintering, pelletisation and briquetting, briquetting is preferred because the other two are associated with higher capital and operational cost. Zimbabwe Alloys has developed operational and technical expertise on the briquetting and utilisation of chromite ore fines and concentrates. Variations in the quality of available chromite ore fines imply that their amenability to briquetting is a dynamic problem. Appropriate briquetting parameters to guarantee quality briquettes are essential to the successful use of briquetted chromite ore fines. In developing a technology for briquetting of chromite ores, it is important not only to study the mineralogical and grain-size characteristics of the chromite ore fines but also to make an informed choice of the type and quantity of the binder and the conditions for producing a physically and chemically competent green and cured briquette. This paper discusses Zimbabwe Alloys' experience on the briquetting process and the advantages derived in the smelting of the briquetted chromite ore fines in comparison to the use of conventional lumpy chromite ore with respect to improvements in chromium recovery and as a consequence related efficiencies and unit cost of production.

Jan 1, 2004

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-technological cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

By J. Kempken, R. Degel, J. Kunze, R. König

The FeNi technology is currently dominated by high-power submerged arc furnaces, often designed as smelter as "two-inline-solution". To achieve the intended high efficiency, state-of-the-art design in good correlation with ores and reductants and an integrated layout of the whole plant is of great importance. An introduction will be given to general aspects in the production FeNi, plus a detailed overview of design principles for large FeNi smelters and finally some examples of innovations and research projects concerning Fe-Ni.

Jan 1, 2007

By R. Banda

This paper describes the decision to implement and then the implementation itself, through trials, of electronic ?Smartdets? over previously used shock tubes. It concludes that Mufulira Mine has become the first mine in Zambia to convert 100% of its stoping to ?Smartdets?, because the Mine?s management was prepared to look beyond the unit cost of product and were ready to look at the broader picture of cost effectiveness and increased productivity.

Jan 1, 2005

By Luthie Els, Chris Coetzee, Roedolf Koekemoer, Casper Els, Olof Vorster, Frank Fereday

Three electric arc furnaces (EAFs) were constructed by Union Carbide at Tubatse Ferrochrome (TFC) in1975. This plant was expanded to four furnaces at the East Plant in 1985 and the gas cleaning system was enlarged without taking flow dynamics into consideration. In order to improve competitiveness, TFC has increased furnace capacity, partially substituted coal for coke, and changed the charge mix. These changes increase the heat and dust load into the air pollution control (APC) system. TFC embarked on a project to improve the APC capacity by: ?Quantifying the required off-gas capacity ?Optimising the aerodynamic flow through the system by means of Computational Fluid Dynamics (CFD) ?Converting the old Brandt Koyo top entry baghouses to bottom entry ?Upgrading the cleaning system ?Installing Gore-tex® ePTFE membrane filter bags The estimation of required off-gas capacity is traditionally done by rule-of-thumb methods such as specific extraction. A more elegant evaluation method was developed for simulating the effects of changes in charge mix on the furnace reaction gas volume and the APC system. Reaction gases are calculated by modelling the reactions taking place in the furnace and off-gas volumes are compared to both fan and baghouse capacity. This enables identification of bottle-necks in the off-gas system. CFD techniques were utilized to evaluate geometric imbalances and propose solutions to ensure optimal use of off-gas capacity. The system modifications were completed over several months and the modified equipment went into service in May2006.

Jan 1, 2007

By P. W. van Deventer

?Soil quality is the capacity of a soil to function, within ecosystem and land use boundaries, to sustain biological productivity, maintain environmental quality, and promote plant, animal and human health?. In the long-term, vegetative rehabilitation of mining wastes aims at, as far as possible, the proper ecological integration of the reclaimed area into the surrounding landscape, which is sustainable and requires minimal maintenance. A certain succession pattern is therefore needed. Recent ecological concepts recognize the role of the substrate?s quality and nutrients in affecting the rates and directions of succession patterns. Although pedogenesis and eventually soil quality in mine waste are not well known, monitoring of soil quality parameters in kimberlite mine tailings reveal a remarkable establishment and or improvement of specifics oil quality indicators. During the same time the vegetative cover?s total functionality as well as reproductive ability improved. Functions of soil, and thus soil quality, can be assessed at the field, farm, ecosystem, pedosphere, and global scale. It is recognized, however, that management of soil becomes increasingly difficult at larger scales, but for demarcated mine waste sites it is possible to ameliorate and manage and assess soil functions and quality. Therefore the significance of the study is the following: soil functions and quality become inseparable from the idea of system sustainability, and are considered as key indicators of ecosystem sustainability on rehabilitated mine tailings material.

Jan 1, 2008

By I. Matsunaga, K. Aoki, W. -j. Jung

Blasting is widely used in mining and basic construction because of its speed and economy to destroy the rocks. Blasting has the advantages of reduced excavation costs and shorted construction time when compared to the use of heavy machinery for excavation and cutting such as that with a tunnel boring machine. There are numerous problems with blasting, including the noise, vibration and fly rock. So it is necessary to accurately evaluate fracture mechanics of rocks on the dynamic loading condition to control the fracture process of the blasting. The tests using Hopkinson's effect for the dynamic condition using the precise detonators were performed for various strain rates on three different kinds of rocks. In the tests using Hopkinson's effect for the dynamic condition, the high-speed camera was used to observe the fracture process of the test sample rocks. As the results of experiments there was an increase in the tensile strength of rock with an increase in the strain rate for three kinds of rock on the dynamic loading. The tensile strength of rocks with high porosity on the water saturation condition was decreased on the both static and dynamic condition. It is clear that the strain rate and water saturation were influenced to the tensile strength of the rocks.

Jan 1, 2003

By D. Chetty

The characterization of platinum group minerals (PGMs) from concentrator flotation circuits provides valuable information towards understanding PGM recovery under given milling and flotation conditions. Additional mineralogical characterization also provides information on ore variability, which may affect recovery. Considering the low grades involved, automated scanning electron microscopy (SEM) characterization of PGMs has enabled relatively quick analyses, compared with older, time consuming and less accurate optical microscopy methods. Over the years, parameters, such as species, size distribution, liberation, gangue and base metal sulfide (BMS) associations, have been used to characterize the PGMs in a process mineralogical context, to aid metallurgical interpretation. This paper considers whether flotation indices determined for PGMs can be empirically validated, using initial results from analysis of PGMs in a concentrate bank from a South African concentrator treating UG2 ore from the western limb of the Bushveld Complex. The aim is to determine whether floatability is adequately described by these parameters, or whether other mineralogical factors must be considered when assessing PGM floatability, and hence accounting for recovery vs. losses to tails. The data obtained to date, show that flotation parameters (including liberation index, BMS/gangue relationships and size distribution) have merits where large changes in PGM concentration occur, as observed in the first four cells of the concentrate bank. Larger data sets, however, are required to assess floatability, particularly where concentrate cell grades are similar, as observed in the last six cells of the concentrate bank. Furthermore, the floatability indices could be enhanced by the incorporation of selected associated gangue mineral information, chief amongst these being the content and mode of occurrence of naturally floatable talc and associated orthopyroxene.

Jan 1, 2009

By I. Ngo, L. Q. Ma, J. S. Guo

Deformation of gob-side entries has always been a critical concern for ensuring stability in longwall coal mines. This paper addresses the significant deformation and support challenges that arise in thick and hard roof longwall faces (THRLF) due to dynamic pressure. The study aims to elucidate the characteristics and mechanisms of deformation during the retreat of the longwall face. The research findings indicated that the primary cause of deformation was the combination of advanced abutment stress resulting from longwall face mining and the movement of the lateral roof over the chain pillar. To mitigate this issue, we propose a deformation control method known as cutting off the lateral roof (COLR) over the chain pillar. Simulation results demonstrate a significant reduction in roof stress and deformation of the gob-side entry after implementing the lateral roof-cutting technique. These findings provide valuable guidance for effectively managing deformation in gob-side entries, particularly when dealing with thick and hard roof strata.

Aug 3, 2023