Search Documents

By S. R. Stadler

Koffiefontein Mine commissioned a distributed antenna system as an underground communication backbone for the DISPATCH® production management system during September1999. STAS Ltd, the supplier of the Distributed Antenna System developed the System for an Integrated and Automated Mine (SIAM). This communication system, in conjunction with DISPATCH®, fulfils Koffiefontein Mine’s present and future requirements for accurate draw control, increasing productivity and improving working conditions. The DAS as SIAMnet communication network was selected by the mine, because of its superior data transmission rate of up to 1.5Mbps at 860MHz, video and Ethernet transmission facilities, and future enhancement abilities. The results of the commissioning tests confirmed the quality and integrity of the data and voice communication. The initial installation enabled 9000 metres of underground production tunnels with voice communication inclusive of 3700 metres having data communication. This article discusses the requirements and selection of the telecommunication system for an underground mine. A description of the installed distributed antenna system follows with a summary of the commissioning tests. A discussion of the reliability of the components is followed by conclusions with suitable recommendations. Keywords: distributed antenna system, underground mining, telecommunication system.

Sep 1, 2001

By M. J. U. T. Van Wijngaarden, R. J. Dippenaar, P. M. Van Den Heever

Some of the important properties of solid electrolytes that influence the performance of electrochemical oxygen probes are discussed in the first part of this paper. It is shown that accurate and reproducible measurements of oxygen in liquid steel are possible with commercial oxygen probes only if great care is exercised in the make-up of the chemical and phase composition, as well as the microstructure of the solid electrolytes used in these probes. To prove this premise, the second part of this study reports on the results of an experimental evaluation of new commercially available oxygen probe. An evaluation of the solid electrolytes used in this probe indicated that the consistency of the chemical composition, degree of stabilization, and microstructure of the electrolytes used are well controlled. The successful application of this particular oxygen probe under industrial conditions was confirmed. It was also found possible to make reliable and reproducible measurements, with acceptable uncertainty, by proper handling of the probe. Some recommendations are made as to the interpretation of the e.m.f. response curve and the use of the electronic processing unit supplied with the probe.

Jan 1, 1987

By T. Wennberg

An elevated location of a paste thickener on a ridge close to the disposal area is considered at a Swedish iron ore mine. About 0.7 M tonnes of thickened tailings are planned to be layered as paste in the vicinity of the thickener over several years with pipeline lengths of up to 900 m after about 20 years. In order to clarify the pipeline pumping characteristics of the tailings product for volumetric solids concentration from 40 to 50%, experiments in loop systems with pipeline inner diameters from 0.063 to 0.152 m have been carried out with various types of pumps. The results and comparisons carried out here showed that the performance of centrifugal pumps cannot simply be related to the rheology, but factors related to pump design and build-up tendencies of material within the pump and other particle properties may be of equal importance. During the first years of operation only one thickener underflow pump is required. The reliability and performance for various pump configurations are planned to be investigated systematically in order to meet the most effective long-term solution for paste thickener operation, pipeline distribution and placement in the disposal area as the discharge point advances over the life of the project.

Jan 1, 2007

Caving is the lowest cost underground mining method provided that the draw point spacing, draw point size, and ore-handling facilities are designed to suit the caved material, and that the draw point horizon can be maintained for the life of the draw. In the near future, several open-pit mines that produce more than 50 kt per day will have to examine the feasibility of converting to low-cost, large-scale underground operations. Several other large scale, low-grade underground operations will experience major changes in their mining environments as large dropdowns are implemented These changes demand a more realistic approach to mine planning than in the past, where existing operations have been projected to increased depths with little consideration of the change in mining environment that will occur. As economics force the consideration of underground mining of large, competent ore bodies by low-cost methods, the role of cave mining will have to be defined In the past, caving was generally considered for rockmasses that cave and fragment readily. The ability to define cavability and fragmentation, the availability of large, robust load-haul-dump units, a better understanding of draw-control requirements, improved drilling equipment for secondary blasting, and reliable cost data have shown that competent orebodies with coarse fragmentation can be exploited by cave mining at a much lower cost than by drill-and blast methods.

Jan 1, 1994

By M. S. Janssen, J. L. Taylor, M. A. Ford, E. B. Viljoen, H. A. Simonsen

The Stilfontein and Buffelsfontein Gold Mines, near Klerksdorp in the Transvaal, had accumulated a large amount of uranium-containing residue and, when the price of uranium rose in the 1970s, consideration was given to the possible recovery of this uranium. Preliminary tests showed that concentration of the uranium prior to leaching would not be economic. However, the pyrite in the residue could be concentrated by flotation, and the flotation concentrate could be roasted to pro¬vide both enough acid for leaching the uranium and a calcine from which the gold could be recovered. The feasibility study showed that a uranium operation of 270 kt per month would be most economically attrac¬tive, and a plant of that size was accordingly designed and built. In the first six years of its existence, the plant treated over 20 Mt of residue and produced about 3,5 kt of uranium oxide. During that time, the plant was con¬tinually being improved to make it more reliable and cost-efficient. This paper analyses the operation of the plant during its first six years from the viewpoints of its mechanical, process, and economic performance. The criteria on which the selection of the process was based are reviewed and compared with the actual performance of the plant, emphasis being placed on the leaching, solid-liquid separation, recovery, and purification stages.

Jan 1, 1987

By J. H. E. Perry, V. H. Wiik

"The ore deposits of the Zambian Copperbelt occur in sedimentary strata that have been subjected to relatively mild, flexure-type folding. Unrolling serves to reconstruct the original depositional geometry of the folded sedimentary strata and is in common usage on the Copperbelt both for geological analysis of drill hole data and in routine ore reserve estimation.A computerized method of unrolling was introduced at Roan Consolidated Mines in 1969 based on a standard contouring program. A contour map of the geological structure is drawn from a regular grid of elevations, interpolated from the original, irregularly-spaced intersections. Unrolling is performed across this grid, perpendicular to one or two axes specified by the geologist. Each intersection is unrolled independently, and the new co-ordinates are subsequently processed to produce unrolled maps.The technique has been used successfully at RCM over the last two years in both the estimation of ore reserves and exploration planning."

Jan 1, 2014

The mining industry worldwide is currently facing a significant restructuring process. In most underground mines, widespread mechanization of the mining processes increases production while reducing staff numbers. At the same time, mining depths as well as the lateral spread of the mine workings are increasing. This ever-changing mining environment requires sophisticated solutions for the design and operation of underground mines. In fact, a reduced number of mining engineers is taking responsibility for everincreasing mine operations. This applies not only to the excavation of the minerals, but also to all other aspects of the mining operation, including health and safety, disaster management, and mine rescue organization. Most mining engineering graduates entering the industry lack experience in mine emergency management. Young engineer trainees must learn mine emergency management and rescue work in addition to their normal training experience on the job. Often, and unfortunately, emergency and rescue training at different mining companies is not carried out to the highest level and standard and with the best possible training outcomes. The tasks and challenges a young engineer faces while being trained in a new position do not leave much room for additional training in mine rescue and emergency management. At the same time, experienced, ?old hands? are retiring and cannot easily be replaced due to limited graduation numbers. Strategies are being developed at mining universities worldwide to train mining engineering students in handling mine emergency situations and to provide hands-on experience for managing potential accident and disaster scenarios underground. Two of these strategies, from the USA and from Central Europe, are presented in this paper. These specific strategies have to be seen under special consideration of the local and regional boundary conditions, but might serve as case studies for mining schools and universities in other countries.

Jan 1, 2014

By N. Henderson, J. Weyer, J. F. Brune

"The mining industry worldwide is currently facing a significant restructuring process. In most underground mines, widespread mechanization of the mining processes increases production while reducing staff numbers. At the same time, mining depths as well as the lateral spread of the mine workings are increasing. This ever-changing mining environment requires sophisticated solutions for the design and operation of underground mines. In fact, a reduced number of mining engineers is taking responsibility for everincreasing mine operations. This applies not only to the excavation of the minerals, but also to all other aspects of the mining operation, including health and safety, disaster management, and mine rescue organization.Most mining engineering graduates entering the industry lack experience in mine emergency management. Young engineer trainees must learn mine emergency management and rescue work in addition to their normal training experience on the job. Often, and unfortunately, emergency and rescue training at different mining companies is not carried out to the highest level and standard and with the best possible training outcomes. The tasks and challenges a young engineer faces while being trained in a new position do not leave much room for additional training in mine rescue and emergency management. At the same time, experienced, ’old hands’ are retiring and cannot easily be replaced due to limited graduation numbers.Strategies are being developed at mining universities worldwide to train mining engineering students in handling mine emergency situations and to provide hands-on experience for managing potential accident and disaster scenarios underground. Two of these strategies, from the USA and from Central Europe, are presented in this paper. These specific strategies have to be seen under special consideration of the local and regional boundary conditions, but might serve as case studies for mining schools and universities in other countries."

Jan 1, 2014

By M. Görnerup, M. Hayashi, S. Seetharaman, C. -Å Däcker

The mould flux plays a crucial role in the continuous casting operation of steel due to its multi-functional assignment as lubricator and heat flux controller. In reality, the commercial fluxes can fall short of the expectations of the operator. In such cases, the performance of the mould flux reduces production throughput in the casting machine. This paper presents the results of a study of two different commercial mould fluxes in continuous casting of steels. The results of online sampling during casting, as well as off-line measurements in the laboratory, are presented. Mould flux powder and slag samples from the caster have been characterized with respect to melting behaviour, interfacial tension and thermal diffusivity, using various measuring techniques. An experimental technique has been developed in order to simulate the melting behaviour of a flux in the mould, which has been found to be useful for qualitative studies. A cross-sectional view of different powders reveals that up to four different material layers may exist in the bed: a loosely packed powder layer, sintered layer, semi-solid layer and liquid slag layer. It is found that the melting rate of the mould flux is dependent on the liquid slag layer thickness. Thus, in a continuous casting operation the melting rate is likely to be non-uniform with position in mould due to the difference in liquid slag layer thickness. Mould slag composition is found to be influenced by the starting powder for as long as 30 min, representing a large part of the first heat casting time. Observations of gas formation indicate that interfacial reactions between the steel and slag take place. Keywords: continuous sacting, mould flux, mould slag, properties

Jan 1, 2004

By T. Marsden

The demand for continuous improvement in the industrial world is an ongoing process. Some sectors, where the competitive forces are well established, have led the development of new and reliable technological innovations. Although the metallurgical industry can rightfully be proud of its process improvements, there is still work to be done in materials and in material handling. In some cases, the improvements will be as simple as adopting technologies that have been perfected in other processing or manufacturing industries. This paper discusses the next design generation for copper tankhouses which will yield: ?Improved copper quality ?Improved equipment availability ?Lower life cycle costs ?Safer operations. These benefits will be realized through new developments and design improvements in: ?Permanent cathodes ?Cathode washing ?Cathode stripping machines ?Anode preparation machines ?Improved lead anode design ?Recycling of lead anodes and refurbishment of cathodes. The demand for base metals, and in particular copper, has led to more research into improving efficiencies in electrowinning and refinery plants around the world. One of the areas previously taken as a matter of course was the production of lead anodes and stainless steel cathodes. In South America alone there are over 600 000 cathodes and anodes in circulation?a very significant figure.

Jan 1, 2009

By S. Jeon, J. Kim, H. Lee

Though the importance of the engineering rock mass properties such as deformation modulus, cohesion and friction angle is emphasized, the researches on the reliability of these values are rarely performed. By using modified Takagi-Sugeno (TS) fuzzy inference system, a fuzzy model was developed based on the data obtained from domestic tunnel construction sites, and the ability of prediction was compared with the empirical equations conveniently used for estimating these values, which finds that fuzzy model is better than empirical equation. Sufficiently large database, however, is required for training the fuzzy model for more accurate prediction. Obwohl die Wichtigkeit der technischen Eigentümer der Felsenmassen wie zum Beispiel Verformungsmodulus, Bindekraft und Reibungswinkel betont werden, wird die Forschung auf der Zuverläßigkeit dieser Werte selten durchgeführt. Mit modifiziertem Takagi Sugenos (TS) Flaumigenschlußsystem wird die Flaumigenmodelle von den Daten, die von inländischen Tunnelbaustellen erhalten werden, entwickelt. Zum Schätzen dieser Werte ist es viel günstig, Flaumigenmodell zu benutzen, als zu adoptieren die empirische Gleichung für die Fähigkeit der Voraussage. Genügende große Datenbank wird aber zum Ausbilden flaumigen Modells für genauere Voraussage erfordert. Quoique l'importance sur la caractéristique d'ingénierie de la masse de roche comme le module de déformation, la cohésion et l'angle de friction, soit soulignée, la recherche sur la confiance de ces valeurs est rarement effectuée. Avec le système modifié de Takagi-Sugeno(TS) fuzzy inférence, le nouveau modèle fuzzy s'est développé. Après avoir estimé sa valeur, nous pouvons savoir que ce modèle fuzzy, basé sur les données venant du chantier de construction de tunnel national, est mieux que l'équaton empirique. Pourtant plus de données de base sont indispensables pour produire le modèle fuzzy plus précis.

Jan 1, 2003

In the wake of the financial crisis that affected world markets in 2002, there has been an increasing international focus on corporate governance. Various corporate governance codes of practice have been introduced, such as the Sarbanes-Oxley legislation in the USA, the Combined Code in the UK, and King III in South Africa. This focus on corporate governance has increased since the most recent financial crisis in 2008, the effects of which are still being felt world-wide. In the mining and minerals industry, reliable metal accounting is essential to sound corporate governance and is also becoming a focus of increased attention and concern, particularly as the figures generated by the metal accounting system feed directly into the financial accounts of mining companies. Mass measurement, sampling, and analysis provide the input data for the metal accounting system and sound corporate governance requires that the procedures used are based on best practice and that the data generated is accurate and handled correctly, transparently, and consistently to produce the accounting reports. The AMIRA Code of Practice for Metal Accounting has been widely adopted in the industry as a means to achieve this, and the compilers of the Code have conducted numerous metal accounting audits at operations, both in South Africa and abroad. These audits have shown that there is a real need for such a code of practice. Keywords metal accounting, AMIRA Code, corporate governance, risk management.

Jan 1, 2014

By A. P. Cook

Gas samples were taken from a wide range of target areas on dumps arising from coal mining activities. Some of the dumps had largely burned out, some were still burning, some were in the process of rehabilitation, and on others rehabilitation was essentially complete. It was found that rehabilitation was very effective in reducing emissions to tolerable levels. Even incomplete rehabilitation reduced the CO2 emissions to less than about 1 kg/m2/a, whereas some unrehabilitated areas showed emissions of over 100 kg/m2/a. Some areas where there was active combustion taking place were also sampled, and they showed as much as 7 000 kg/m2/a, but the areas concerned were very small and their total contribution accordingly low. Analyses were also made for SOx, NOx, NH3, and CH4, but these were generally (and unexpectedly) at very low levels. The mines sampled represented 53 per cent of all surface coal mining activity. Accordingly the estimated total emissions were scaled up, to arrive at estimates of 1950 000 ± 350 000 t/a C02, 2040 ± 580 t/a SOx, 306 ± 85t/a NOx, and 31 ± 9 t/a NH3 for all surface mines. Methane was detected only from burning coal, and due to the difficulty in sampling, no reliable estimate could be made of these methane emissions.

Jan 1, 2012

By R. Singh, A. K. Dhawan, M. Dixit, H. Dev

ABSTRACT: The modulus of deformation of rock mass is an important engineering parameter required for the design of foundation of hydraulic structure and to study the interaction of rock mass and the structure at the foundation support. Different equipment and techniques are used to arrive at the design modulus value. Since any error in the estimation of modulus values results in multiplication of its effects in the analysis, it is necessary to know about the reliability of testing equipment and procedures. In the present study modulus values obtained by different in-situ equipment at different project sites have been compared. KURZFASSUNG: Der Verformungsmodul von der Felsenmasse ist technisch ein wichtiger Parameter, den man zur Konstuktion des Grunds fuer die Hydro – Tektonik, benoetigt um auch die gegenseitige Beeinflussung der Felsenmasse und der Tektonik am Traggrund zu betrachten. Verschiedene Geraete und Methoden werden angewandt, um den Ausfuehrungsmodul -Wert zu erreichen. Es ist erforderlich, die Zuverlaessigkeit der Pruefeinrichtung sowie des Verfahrens zu kennen, da irgend ein Fehler in der Abschaetzung von Modulwerten in der Analyse zu einer Vervielfachung ihrer Einwirkung fuehrt. In der vorligenden Arbeit werden die Modulwerte gewonnen aus unterschiedlichen Einrichtungen an Ort und Stelle and verschiedenen Projekt -Stellen mit einander verglichen. SOMMAIRE: Le module de deformation d’une roche est un parametre important pour la conception et realisation des ouvrages hydrauliques ainsi que pour etudier l’interaction de la roche et de la structure d’appuis de base. De divers equipments et techniques sont employes pour determiner la valeur de ce module de conception. Puisque l’effet d’une erreur d’evaluation du module devient multiplie dans l’analyse, il est necessaire de savoir la fiabilite des equipments et des methods qu’on ulilise. Dans cette etude, on a compare les valeurs des modules obtenues en employant les equipments in-situ aux sites differents de projets.

Jan 1, 2003

By J. de Korte, Z. Loubser

"SynopsisThe aim of a blending stockpile is to minimize the natural variation in properties of a material. Two simulation models were written, for coneshell and chevcon stacking, and used to investigate the influence of different stockpile parameters on blending efficiency. The coneshell model is used to show that blending efficiency is highly sensitive to stacked height, with lower output variances observed for higher capacities. Output variance in both models also decreased when the stacker movement increment was decreased. For chevcon stacking, increasing stacker speed significantly increases the blending efficiencies. Increasing the length of the blending tail also reduces output variation, but this parameter would need to be weighed against the accompanying decrease in buffer capacity.IntroductionEven in the most uniform deposit of materials in nature, material properties will vary. The degree of variation can be measured, and usually resembles a normal distribution. The aim of blending and homogenization operations is to minimize the standard deviation of this normal distribution (De Wet, 1994). In general, the reduction in variation will result in a more efficient and cost-effective downstream process. Cement plants need a precise blend of raw materials to ensure desired kiln performance; boilers used in power generation are optimized for fuels of a constant specification; and even though the separation density in a coal washing plant can be adjusted, a constant product quality cannot be produced from highly variable feed (Denny and Harper, 1962). The process efficiency, product quality, and environmental compliance depend on consistency of characteristics in the material fed (Kumral, 2005) Many industries involved in"

Jan 1, 2015

By D. Burrows

Traditionally, characterisation of the mineralogy and textures of ore and rock samples were based on observations of hand specimens and thin sections using an optical microscope. The extent of the data collection was limited by the available tools and thus variations in mineralogy and texture were generally not described by quantitative data. These qualitative to semi-quantitative approaches, even though well established over the years, resulted in variable observations and data sets. The data were unlikely to be representative of a sample and limited statistical validity meant the results could not be reliably used in modern digital mining design and planning. With recently developed SEM based quantitative mineralogy tools and the corresponding methodologies, ore textures can be quantified and compared numerically. The numerical data can not only enhance the understanding of an orebody in geological terms, but can also be used in the creation of metallurgical models for mine and mineral processing design and simulation. These capabilities provide valuable inputs to risk assessment studies and the evaluation of mineral projects.

Jan 1, 2007

By Siyabonga Malevu

Chemical Initiatives? Umbogintwini plant is the production facility of Chemical Initiatives? business. Umbogintwini?s J Plant manufactures sulphuric acid. The plant was designed and built by Simon Carves, and was commissioned in 1974. The plant was designed to produce 500 tons/day of Sulphuric acid (H2SO4) at maximum rates. The Sulphuric acid manufacturing is through the famous contact process whereby liquid Sulphur is injected through dried air in a burner operating at 1000 °C to form sulphur dioxide (10.5% SO2). The SO2 gas is then cooled in waste heat boiler no.1 before being fed to a four pass converter which provides 99.5% SO2 conversion to sulphur trioxide (SO3). The SO3 gas is the absorbed by 98.5% H2SO4 through the inter-pass & final tower to make more concentrated acid and dilute it with water back to 98.5% H2SO4 in acid pump tanks and dispatched to storage tanks. The manufactured Sulphuric acid is supplied to a variety of industrial manufacturing customers includes Pulp & Paper industry, Mining industry, Chemical manufacturing industry etc. During the 1st quarter of the year 2007, Chemical Initiatives undertook a study to up rate the sulphuric acid plant output by 10% (i.e. from 500 tpd to 550 tpd).

Jan 1, 2009

By V. Borissenkob, L. D. Ropera, M. J. Danielc

Eccentric High Pressure Centrifugal Comminution (eHPCC) is a novel comminution device that provides a single step to achieve a desired target grind size. The mechanisms within the unit mirror particle breakage that is akin to high-pressure-grinding rolls (HPGR) and high-intensity-attrition with air classification. eHPCC receives lump and can produce a product P80 such that the progeny are at or less than natural grain size of the feed. The unit operates in either closed or open-circuit. The grinding zone is dry and free of steel grinding media. This paper presents evidence of eHPCC-2 capable of selective and preferential mineral liberation. A recent test campaign on a blend of underground quartzgold- vein ore was completed. The feed to eHPCC-2 trial was SAG mill trommel oversize (low-grade pebble rejects). eHPCC-2 operated open-circuit with air-fluidisation in the rotating-grinding-chamber, classifying particles based on terminal velocity of the air-swept product particles, displaying size and mineral composition classification taking place at the same time. There is an opportunity for future industrial research targeting eHPCC as an advanced integrated comminution and classification technology. Keywords: High pressure, high intensity, compression, attrition, comminution, classification

Jan 1, 2020

By N. G. Cook, N. C. Joughin, A. J. A. White

The rate of face advance in the gold mines is between 3 and 10 m a month, with a median value of about 5 m a month; it follows that faces are blasted less frequently than is planned. There are many advantages in the use of short holes for stoping to give face advances of from 0,7 to 0,8 m per blast. This has the potential for so increasing the frequency of blasting that monthly rates of face advance could be improved significantly. Cleaning with face scrapers is too slow to permit the maximum achievement of a complete clean, drill, and blast cycle for each shift. Short-hole blasting, combined with the use of mechanical conveyors for face cleaning, offers the possibility of completing two such cycles each day, yielding monthly rates of face advance of up to 35 m. Experiments aimed at developing safe, unitized explosive charges well-suited to produce reliable face advances of 0,7 to 0,8 m per blast under a wide range of gold-mining conditions have been notably successful. A novel method of assessing the effectiveness of a blast based on the percentage of holes that leave socket lengths of 5 cm or less was used. Unitized charges of 60 per cent Ammon gelignite, 600 mm long by 25 mm in diameter, appear to be near optimal. The explosive is de-sensitized to obviate detonation by chance mechanical impact, but requires only a 6D detonator for initiation; it has good water-resistance. Means have been developed for producing these cartridges automatically, but the necessary machines will have to be built specially and the cartridges are not yet available in large numbers. A second experiment by way of an extended pilot production trial using these cartridges in holes 0,9 m long is now under way. Preliminary results indicate that drilling and explosive efficiencies and productivity are well above average, even though face scraping is being used. Unitized charges of this type are likely to prove even more advantageous when mechanical face conveyors come into use.

Jan 1, 1975

By Keith Rowley, Neal Harries, David Noon

The management of risks associated with slope instability is an essential process in the safe and economic operation of open cut mines. The ?slope stability radar? (SSR) has been developed to better manage those risks. The SSR remotely scans rock slopes to continuously measure any surface movement and can be used to detect and alert users of wall movements with sub-millimetre precision. The high level of movement precision and broad area coverage of the rock face can allow for a better understanding of the geomechanics of slope deformation, including magnitude of potential failures and additional warning time of impending instability. Additionally, radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. SSR systems have been deployed in many mines in Australia, Indonesia, South Africa, Zambia, Chile and the United States. Greater than 70 rock falls and waste dump failures (from several to millions of tonnes) have been monitored, and on every occasion precursor ?warning? movements were recorded by the SSR. This technology enables a radical change in the management of risks in open cut mining. This paper will present recent case studies of the SSR operation in coal and metalliferous mines.

Jan 1, 2006