Search Documents

By Antonio Karzulovic, Sergio Olavarría, Patricio Adriasola

The economical analyses of different Chuquicamata open pit mine planning scenarios, indicate that the pit closure should occur at latest in the year of 2017. However, about 60,000 m of drill holes have demonstrated that below the pit bottom there is a potential of 2.3 billion tons of ore. Hence, Division Codelco Norte developed the scoping engineering for a large underground panel caving operation, similar to El Teniente mine. This project considers the exploitation of a 2500 m 300 m footprint, with three 250 m lifts. The plan considers to initiate the construction in the year 2009, to begin the production in the year 2015 and achieve a production rate of 45 million tons per year in the year 2021. A large-scale transition from open pit to underground mining like this one presents three main challenges: (1) to include the geotechnical aspects relevant for mine design and mine planning, (2) to define the proper surface and underground infrastructure, and (3) to fulfil the project deadlines and to achieve the production targets. This paper summarizes this transition project and discusses these three main challenges.

Jan 1, 2006

By D. M. MacHunter, M. K. Palmer

Refinement of design parameters and features has resulted in the development and commercialization of spiral separator models that offer enhanced performance for a number of application areas. Examples of recently developed spiral separator models include the enhanced performance (EP)spiral and the HC (high capacity) series. Comparative performance data for appropriate applications are presented for each of these new model spiral separators. The utilization of spiral separators providing improved performance offers significant cost and operational benefits for process plants. Examples of process flowsheet changes that have resulted from the incorporation of recently developed spiral separators include the reduction of the number of process stages and the achievement of high density tailings by the utilization of a dewatering arrangement in the spiral tailings splitter system.

Jan 1, 2003

By E. L. J. Kleynhans, J. I. J. Fick, J. P. Beukes, P. G. van Zyl

"Ferrochrome (FeCr) is vital for the production of stainless and high-alloy ferritic steels, since it is the only source of new Cr units. FeCr production is an energy-intensive process. The pelletized chromite prereduction process is most likely the FeCr production process with the lowest specific electricity consumption (SEC), i.e. MWh/t, currently in operation. However, due to increases in costs, efficiency, and environmental pressures, FeCr producers are attempting to lower their overall energy consumption even further. Recently, it was proven that pre-oxidation of chromite ore prior to pelletization and prereduction significantly decreases both the SEC and lumpy carbonaceous reductants required for smelting. This paper presents the first attempt at conceptualizing the technoeconomic feasibility of integrating chromite pre-oxidation into the prereduction process. Financial modelling yielded a net present value (NPV) at a 10% discount rate of approximately R900 million and an internal rate of return (IRR) of approximatelyy 30.5% after tax, suggesting that the implementation of pre-oxidation prior to pellet prereduction may be financially viable. Sensitivity analysis indicated that the parameter with the greatest influence on project NPV and IRR is the level of prereduction. This indicates that the relationship between maintaining the optimum pre-oxidation temperature and the degree of prereduction is critical for maximium process efficiency. IntroductionStainless steel is a crucial alloy in modern society. Virgin chromium (Cr) units used in the manufacturing of stainless steel are obtained from ferrochrome (FeCr) – a relatively crude alloy consisting predominantly of Cr and iron (Fe) (Murthy, Tripathy, and Kumar, 2011; Beukes, van Zyl, and Ras, 2012). FeCr is produced mainly by the carbothermic reduction of chromite ore in submerged arc furnaces (SAFs) and direct current arc furnaces (DCFs) (Neizel et al., 2013; Beukes, Dawson, and van Zyl, 2010; Dwarapudi et al., 2013). The energy required to heat, smelt, and reduce the chromite ore to the metallized state is supplied by electricity (Pan, 2013). FeCr production is an energy-intensive process, with a specific electricity consumption (SEC) varying from 2.4 MWh/t to more than 4.0 MWh/t FeCr produced, depending on the process applied (Pan, 2013; Neizel et al., 2013). Daavittila, Honkaniemi, and Jokinen (2004) stated that the typical operational costs of FeCr smelters can be divided into four categories, i.e. chromite ore (30%), carbonaceous reductant (20%), electricity (30%), and other production costs (20%). This makes electricity consumption the joint largest factor that influences operational costs in FeCr production."

Jan 1, 2017

By M. Natarajan, C. J. Cutler, E. Mponda

Keywords: Pyrometallurgy, furnace, KCM Nkana, Zambia The Nkana smelter was initially commissioned in 1931, with two reverberatory furnaces, two Peirce-Smith converters, and blister copper casting facilities. Reverberatory furnaces were the mainstay of production up until 1994, when an El Teniente Converter (CT) was installed to upgrade reverberatory furnace matte to white metal, prior to converting in conventional Peirce-Smith (PS) converters. In 2000, a decision was taken to increase the proportion of concentrate smelted in the CT by introduction of bone-dry concentrate injection through the tuyeres. A flash dryer with a nominal capacity of 1 200 metric tons per day of dry product, and associated tuyere injection system was commissioned in March 2004. Based on the projected concentrate arisings from the KCM mines into the future, as seen in 2004, it was decided to develop the CT to be the primary smelting vessel at Nkana, to handle a minimum of 1 250 tons per day of concentrate, and to operate only one reverberatory furnace in slag-cleaning mode pending a full evaluation of alternative slag-cleaning technologies. The anticipated cathode production from Nkana was to be in the range 140 to 150 000 tons per annum. This paper details the outcomes from trials that were carried out in August and September 2004, using two reverberatory furnaces for slag cleaning. The results of these trials, plus further work in October and November, provided confidence to move to one reverberatory furnace for slag cleaning in December 2004. With the advent of Vedanta as the majority shareholder in KCM at the end of 2004, the approach has been to maximize the available smelting capacity. Currently, two reverberatory furnaces and the CT are on-line, with the higher silica concentrates going to the reverberatory furnaces with an appropriate amount of pyrite, and the cleaner concentrates going to the CT. Expansion of the smelter is currently under investigation.

Jan 1, 2006

By Ö. Uysal

This study deals with the presentation of the mechanized longwall mining project introduced some years ago to increase productivity and output of Aegean Lignite Establishment (ELI) owned by Turkish Coal Enterprises (TKI.) and the comparison of this method with a planned alternative new mining method called ?shortwall mining? where continuous miners will be introduced as primary coal excavation machines. Following the planning phase, production costs have been calculated for both mining methods on the basis of a panel having a height of 7.5 m. In addition to cost analysis, both methods have been evaluated using ?the multi-dimensional objective system?. In this evaluation the value synthesis has been carried out according to scoring models. Lastly, the advantages and disadvantages of both production methods have been stated by analysing them according to related criteria. In the light of outputs gathered from the analyses, it has been determined that the shortwall mining method will out perform the longwall method. Keywords: continuous miner, shortwall mining, longwall mining, multi-dimensional objective system.

Jan 1, 2006

Mr R.D. Beck attended Felsted School in Essex (England) and the Royal School of Mines, University of London, where he ob¬tained the degree of B.Sc.(Eng.), A.R.S.M. in mineral technology in 1969. His other qualifications include Pr.Eng. (1976), C.Eng (1975), and M.I.M.M. (1975). He joined Gold Fields of South Africa in December 1969, and worked at Doornfontein Gold Mine, Greenside Colliery, West Driefontein Gold Mine, Zwartkloof Fluorspar, Gold Fields Laboratories, Gold Fields Head Office, Libanon Gold Mine, and Kloof Gold Mine before being appointed Plant Superintendent at East Driefontein Gold Mine in January 1973. In June 1976, he was transferred to Head Office as Group Metallurgist, followed, in November 1978, by his secondment to Black Mountain Mineral Development Company as Plant Superintendent, to take on-site responsibilities for staff training, plant commissioning, and start up. On his return to Head Office in July 1980 as Assistant Consulting Metallurgist, he was responsible for Black Mountain and new metallurgical projects. Then, in January 1984, he was appointed General Manager of the Zinc Corporation of South Africa Limited. He became a member of The South African Institute of Mining and Metallurgy in 1973.

Jan 1, 1985

By J. Drzewiecki, J. Kabiesz

Coal mining using longwall methods of mining can lead to intense disturbances of undermined roof strata. The disturbances may extend beyond the extraction area and the resulted rock mass deformations will appear differentiated. In the case of stiff and undermined roof strata, the energy stored in these rock masses may be frequently dissipated in the form of high-energy seismic tremors. Such events can occur if these strata should fail or „free themselves” either from the constrainment of rock environment or from adjacent strata. It has also been found that the amount of the stored energy closely depends on the size and/or slenderness of these strata. Thus, it would be possible to apply specific preventive measures to reduce the energy of mining – induced seismic tremors. The methods are based on artificial disintegration of the structure of energy – storing strata. One of the most efficient methods is a method of directional hydraulic fracturing, which is regarded as an alternative solution from the traditional blasting and hydraulic methods.

Jan 1, 2003

By C. Debek, A. Wasilewicz, T. Czysz

"Both Polish and European hard coal mining nowadays faces the need of deepening shafts (significantly in some cases) or extending mining hoists, due to the exploitation of deeper coal deposits.In order to protect the crew working within a shaft, rope safety platforms (artificial shaft bottoms) are employed. Old solutions, based on rigid steel constructions with the external damping layers made of e.g. slag and up to several tens of metres long, are intended to absorb the energy of approximately 5 t mass falling a distance of 700 m. However, current requirements often assume a drop of 20 t to a depth of 1000 m or even more.More modern safety platform structures, made of one or more support rings with steel ropes stretched on them (rope platforms), are more compact (up to 3 m high) and lighter than traditional solutions. Multi-ring rope platforms with additional damping layers filling the empty spaces between the ropes are able to absorb sufficient energy to meet the current requirements.Single- and double-ring platforms have been employed in Poland to absorb the energy of approximately 5 t dropping to a depth of 900 m. They have been developed (and some have already been implemented) by SADEX Ltd. and are protected by various patents and patent applications.This paper presents a design for a triple-ring platform structure with six rope nets. FEM analysis was used to model the performance of the platform. According to the simulation, a 20 t mass falling from 1000 m (>100 m/s) will destroy all the nets, breaking most of the ropes and deforming the support steel boards placed on the nets, but will ultimately be stopped by the platform, as its kinetic energy falls to zero."

Jan 1, 2017

By L. Lorig

"Two types of extreme event, earthquakes and rainfall, potentially affect open pit slope stability. In the case of earthquakes, there are rather well-developed analysis procedures and acceptability criteria. The analysis procedures relate mainly to selection of the dynamic loading either through design earthquakes and/or pseudo-static seismic coefficients. The acceptance criteria are typically expressed in terms of a minimum safety factor in pseudo-static analyses. The acceptance criteria are often promulgated by governments despite the fact that no open pit slope has ever been adversely affected by an earthquake. This paper explains why open pit slopes are seemingly more resistant to dynamic loads than natural landforms, which can experience catastrophic landslides.Extreme rainfall events are much more likely to cause open pit slope problems than earthquakes. Two types of problem are common – slope erosion and slope instability. Slope erosion is often mitigated by appropriate surface water controls. Slope instability due to elevated transient water pressures is more difficult to mitigate. Analysis procedures and acceptability criteria are rare. This paper will discuss the mechanisms for rainfall-induced slope instability, as well as analysis methods. Examples will be discussed and analysis methods are proposed. IntroductionTwo types of extreme event, earthquakes and rainfall, potentially affect open pit slope stability. In the case of earthquakes, there are rather well-developed analysis procedures and acceptability criteria. The analysis procedures relate mainly to selection of the dynamic loading either through design earthquakes and/or pseudo-static seismic coefficients. The acceptance criteria are typically expressed in terms of a minimum safety factor in pseudostatic analyses. The acceptance criteria are often promulgated by governments (e.g., Peru, Chile) despite the fact that no open pit slope has ever been adversely affected by an earthquake. This paper explains why open pit slopes are seemingly more resistant to dynamic loads than natural landforms, which can experience catastrophic landslides.Extreme rainfall events are much more likely to cause open pit slope problems when compared to earthquakes. Two types of problems are common – slope erosion and slope instability. Slope erosion is often mitigated by appropriate surface water controls. Slope instability due to elevated transient water pressures is more difficult to mitigate. Analysis procedures and acceptability criteria are rare, but do exist. In Peru, for example, slopes are required by law to be designed for a 100-year storm."

Jan 1, 2016

The paper examines the design issues associated with the integration of mineral processing within underground mining systems. It demonstrates conceptual integrated system design options appropriate to a range of geological scenarios. Particular reference is then given to a case study of stoping in narrow base metal veins. The performance of such integrated systems in terms of productivity, economic and environmental criteria is demonstrated by means of simulation. Particular attention is given to the potential benefits to mine waste management. Processing technologies appear to offer genuine potential benefit, whilst underground mining methods may need to evolve further to facilitate full integration. This paper is based on industry supported research aimed at developing selective and clean underground mining systems.

Jan 1, 2003

By S-L. Weeber

Ash fusion temperature is the temperature at which the mineral matter in coal begins to soften, flow and fuse. It is an important parameter relating to coal utilization. Optimum ash fusion temperatures derived from coal in the Witbank Coalfield region are approximately 1400°C, and higher, although temperatures above1300°C may be deemed acceptable. This study attempted to determine which factors, mineralogical or inorganic-chemical, influence variations in the ash fusion temperatures in certain coals. Coal was sampled from the Number 2 coal seam at opencast and underground workings at New Clydesdale Colliery, Witbank Coalfield, South Africa. The samples represented known low and high ash fusion temperature coal. Analyses performed included proximate analyses, calorific value determination, percentage sulphur, ash fusion temperatures, ash analyses (composition of ash), X-ray diffraction, scanning electron microscopy and petrographic studies. Results show that although a complex relationship exists between ash fusion temperature and the various geological and coal parameters, some positive correlative results were obtained. These indicate a possible relationship between low ash fusion temperatures and i) finer size fractions, ii) an increase in iron content present in the form of pyrite and iii) the form in which pyrite is present, namely cleats. High ash fusion temperatures tend to correlate with i) the absence of pyrite or ii) pyrite present as framboids.

Jan 1, 2000

By C Katongo

Ground condition at No1. Shaft varies across the mine. The different ground conditions arise as a result of the differences in the rock strength and structure, seismicity and induced stresses in abutments areas. Apart from being a major cause of Fall of Ground incidents/accidents, adverse ground conditions where encountered has affected the rate of development advance as well as production. This implies that for support to be cost effective Geotechnical section has to ensure that support is designed to prevailing ground demand to ensure the safety of personnel and minimize loss of production. We have also seen changes in mining methods as a result of change in ground conditions. To avoid incurring unnecessary costs through remedial works resulting from ground deterioration and collapses of development openings due to inadequate support, the principle in engineering design is ?Do it right the First Time?, and this can only be achieved through good understanding of Geotechnical environment. The paper discusses the different ground conditions encountered in various development ends at No.1 Shaft. It also discusses the principles of ground support, failure mechanisms, types of ground support systems employed, and the different techniques used to select support systems, and quality control techniques in underground support installation.

Jan 1, 2005

By D. W. Nel

Nanofiltration (NF) has attracted much attention over the past few years due to the reduced energy consumption compared to reverse osmosis (RO) and better separation performance compared to ultrafiltration (UF). Although research has been done in the area of NF of nickel ions, sodium ions, and acid separation, not much attention has been given to the separation of high nickel concen¬trations from sulphuric acid streams. The use of NF for the separation of nickel and acid from a spent nickel electrolyte is an innovative process alternative for future industrial application within a base metal refinery. In this study, the separation performance of a composite polyamide NF membrane on a spent nickel electrolyte was investigated by varying the sodium sulphate concentration in the feed (50-150 g/l), the trans-membrane pressure (35-55 bar), and cross-flow velocity (1.5-3.5 m/s), and measuring quantities such as total permeate flux, acid rejection, nickel rejection, and sodium rejection. The nickel and acid concentration in the feed were kept constant with variations between 40-60 g/l and 25-40 g/l respectively, while the temperature of the experiments was kept constant at 50°C. The membrane was found to be very selective for nickel ions, with the rejection of nickel ions varying between 54.4% and 98.2%. The rejection of acid ions varied between -5.9% and 21.8%. The rejection of sodium ions varied between 16.6% and 72.4% at a cross-flow velocity of 2.5 m/s and sodium sulphate concentration of 50 g/l in the feed solution. An increase in trans-membrane pressure increased the rejection of nickel, sodium, and acid ions, while an increase in sodium sulphate concentration decreased the rejection of nickel and acid ions. The total permeate flux was found to increase with an increase in trans-membrane pressure and decrease with an increase in sodium sulphate concentration. The cross-flow velocity had an insignificant effect on the total permeate flux and the rejection of nickel, sodium and acid ions.

Jan 1, 2013

By D. J. Greeff

By making use of genetic programming, empirical models for metallurgical processes can be evolved that are more cost-effective than models determined by means of classical statistical techniques. These methods explore populations of candidate models assembled from sets of variables, parameters and simple mathematical operators, and do not require explicit specification of model structures. The application of the proposed strategies is illustrated by means of a case study pertaining to the leaching of nickeliferous chromite ores. Modelling of the nickel and cobalt extraction from the ores yielded models of similar accuracy compared to those obtained by non-linear regression and artificial neural networks. However, in the case of the iron extraction from the ores, the genetic programming model was significantly more accurate than both the regression and neutral network models.

Jan 1, 1998

By R. M. Lamya

A semi-empirical kinetic model was developed for the atmospheric leaching of a Ni-Cu matte in copper sulphate-sulphuric acid solution. Kinetics of the leaching process was studied as a function of initial copper ion concentration, initial acid concentration, temperature, stirring rate and particle size distribution. The kinetic model was developed on the basis of the leaching mechanism and chemical reactions of the leaching system investigated, and was evaluated by comparing the model predictions to experimental data. The model was found to satisfactorily fit the trends in the leaching of the metals, namely copper, nickel, cobalt and iron.

Jan 1, 2009

By M. Olper

The change in regulations and the strong attention to the environment have suggested some changes in the traditional processes for the recycling of lead acid batteries. Engitec Technologies, marketing the Integrated CX® System, is continuously updating and improving its technology to fulfil the technical, economical and ecological requirements coming from the market and from the environmental authorities. In this paper Engitec Technologies will present the latest technical innovations introduced in the Integrated CX® System.

Jan 1, 2008

By Marek Dworzanowski

Dense medium separation (DMS) is critical to the operation of coal and diamond beneficiation plants. It is also utilised in iron ore, manganese, chromite and andalusite beneficiation as well as pre-concentration for platinum-bearing UG2 ore. Gravity concentration plays an important role in the processing of diamonds, coal, gold, platinum, titanium minerals, zircon, chromite, iron ore and manganese. The DMS and Gravity Concentration operations and technology in South Africa conference will focus on the operation of DMS and Gravity Concentration circuits in the South African Mining Industry. The current status of the technologies and equipment employed will be presented as well as future developments. The conference was set up to showcase South African DMS and Gravity Concentration operations and provide a forum where operators, technology and equipment suppliers can engage in knowledge sharing. The papers cover a wide spectrum of topics, including descriptions of operations, optimisation projects, new capital projects, equipment applications, process monitoring and process selection. Most commodities and unit processes associated with DMS and Gravity Concentration are covered. The conference venue was selected to be the CSIR Convention Centre in Pretoria. The CSIR has contributed to DMS research in South Africa and it is located not far from many coal, diamond, gold, platinum and chrome mines that extensively utilise DMS and Gravity Concentration in their beneficiation plants. I believe that the papers and presentations submitted for this conference will provide a valuable future reference for DMS and Gravity Concentration, thus making the work of all the contributors to this conference highly rewarding and worthwhile.

Jan 1, 2006

By A. M. Ghodgaonkar, P. J. Bhonde, R. D. Angal

Primarily ferrochrome is used to introduce chromium into steels and alloys. Chromium enhances hardness, hardenability, corrosion, abrasion and wear resistance of the steel. High carbon ferrochrome is one the cheapest sources of chromium, which finds large consumption in foundries and steel plants. However, carbon leads to problems viz. weld decay and sensitization of steels at elevated temperature causing catastrophic failure. Thus high carbon ferrochrome which otherwise enjoys financial edge over its low carbon grade is not suitable for final alloying or adjustment of chromium content. Subsequently, its addition burdens a steel maker. Hence, metallurgists around the globe have researched on finding out suitable technique for refining of ferrochrome. Traditional production methods of low carbon ferrochrome have drawbacks i.e. high refractory consumption, losses of chromium in slag and fumes etc-. Later these were overcome by adopting relatively new methods namely, metallothermic reduction, triplex process, vacuum technique to directly produce extra low carbon ferrochrome. Authors have carried SWOT analysis of the aforementioned techniques in the literature. Key Words: Ferrochrome, carbon content, low carbon grade, chromite, sensitization

Jan 1, 2007

By G. van Aswegen

The geometry and morphology of a set of low-angle fractures around a stope in a deep Witwatersrand gold mine are explained in terms of extension fractures forming under variable conditions of stress. Primary extension fractures (E1) form some distance ahead of an advancing stope along the s1, s2 plane. With stope advance, a couple of these fractures end up in a stress regime conducive to transpressional shear and a secondary set of extension fractures(E2) is formed at a high angle to the primary fractures. i.e. at a low angle to the stope. As the E2 fractures are undermined, they migrate into a stress regime of transtensional shear and a third set of extension fractures (E3) may develop between E2 fractures. These have sigmoidal shapes, being parallel to the E2 fractures at the E2 discontinuity where s3 is negative, and curved through the un-fractured rock between E2 fractures where s3 is positive at the instant of fracturing. The fractures all display fractographic features characteristic of dynamic extension failure with striae indicative of the direction of rupture propagation and the local, instantaneous orientation of s1.

Jan 1, 2012

By S. M. Spottiswoode, Linzer. L. M.

We report on further progress in improving seismic locations by using the so-called double-difference method (Spottiswoode and Milev, 1998 and Waldhauser et al., 1999). Double-differences are obtained either using picked arrival times or various measures of time differences obtained from waveform pairs. The double-difference method provides for much improved relative locations by reducing the effect of the errors in the wave velocity of ray paths between each event and each geophone. Further improvements are obtained by using known locations, such as blasts. One of the difficult problems that we have overcome is that of finding the best “weights” for the time corrections. Experience obtained in relative moment tensor inversions by Andersen (2001) suggests that use of median corrections is both more stable and more accurate, even while the locations of the individual events is based on weighted least-squares minimization. A hybrid location program with known reference events has been developed. Tests on a synthetic data set gave relative locations that were much less widely spread than the absolute locations. The use of known event coordinates (blasts) moved the relative locations back towards the real locations. These results are confirmed in preliminary analysis of data from a mine. The absolute locations are adjusted using blast events restricted to the line of tunnel development. Inter-event distances are distributed in a power-law fashion that suggests that the relative location accuracies are improved by a factor of three or more. Nous rendons compte des progrès faits dans l’amélioration des locations de séismes en utilisant la méthode appelée de double- différence (Spottiswoode and Milev, 1998 et Waldhauser et al., 1999). On obtient les double-différences soit en utilisant des temps d’arrivée choisis soit des mesures variées de différences de temps obtenues de doublets de forme d’onde. La méthode de double-différence fournit des locations relatives très améliorées en réduisant l’effet des erreurs dans la vitesse d’onde des trajectoires de rayon entre chaque évènement et chaque géophone. D’autres améliorations sont obtenues en utilisant des locations connues, telles que les coups de mine. Un des problèmes difficiles que nous avons surmontés est celui de trouver les meilleurs coefficients de pondération pour les corrections de temps. L’expérience obtenue dans des inversions de phases tensorielles relatives par Andersen (2001) suggère que l’utilisation de corrections médianes est à la fois plus stable et plus exacte, même lorsque la location des évènements individuels est basée sur minimisation pondérée de moindres carrés. Nous avons développé un programme hybride de location avec des évènements connus pour référence. Des tests sur des données artificielles ont donné des locations relatives qui étaient beaucoup moins étendues que les locations absolues. L’utilisation de coordonnées d’évènements connus (coups de mine) a ramené les locations relatives vers les locations réelles. L’analyse préliminaire des données d’une mine a confirmé ces résultats. Les locations absolues sont ajustées en utilisant des évènements de coup de mine restreints à la ligne du développement du tunnel. Les distances entre chaque évènement sont distribuées comme par loi exponentielle ce qui suggère que les degrés d’exactitude des locations relatives sont améliorés par un facteur de trois ou plus. Wir berichten über einen weiteren Fortschritt, die seismische Positionen unter Verwendung der zu sogenannten Doppel-Unterschied-Methode (Spottiswoode und Milev, 1998 und Waldhauser et al.,1999) zu verbessern. Doppel-Unterschiede werden entweder mit ausgewählten Ankunftszeiten oder verschiedenen Messungen von Zeitunterschieden erreicht, die von den Wellenformpaaren erhalten werden. Die Doppel-Unterschied-Methode liefert viel verbesserte relative Positionen unter Verringerung der Auswirkung von Fehlern in der Wellengeschwindigkeit von Strahlengängen zwischen jedem Fall und jedem Geophon. Weitere Verbesserungen werden erreicht, indem man bekannte Positionen, wie Sprengungen verwendet. Eines der schwierigen Probleme, die wir überwunden haben, ist jenes des Findens der besten "Gewichte" für die Zeitkorrekturen. Die Erfahrung, die in den relativen Momentspannerumkehrungen von Andersen (2001) gewonnen werden bietet den Schluß an, daß der Gebrauch von mittleren Korrekturen beständiger und genauer ist, sogar wenn die Positionen der einzelnen Fälle auf der bewerteten Reduzierung der Methode der kleinsten Quadrate basiert. Ein hybrides Positionsprogramm mit bekannten Bezugsfällen ist entwickelt worden. Tests auf einem synthetischen Dataset gaben relative Positionen, die viel weniger weit gestreut waren als die absoluten Positionen. Der Gebrauch von bekannten Fallkoordinaten (Sprengungen) schob die

Jan 1, 2003