Search Documents

By K. M. Banks

The hot ductility of in situ melted tensile specimens of micro-alloyed steels having C contents in the range 0.12?0.17% (mass %) have been examined over the 700?1000°C temperature range. An improved testing method for simulating the continuous casting process was used, which takes into account both primary and secondary cooling conditions. Increasing the N content to electric arc furnace levels (0.01% N) was found to cause a serious deterioration in ductility. V-N steel gave better ductility than Nb-containing steels due to less precipitation. From a cracking perspective, low- N steels are generally recommended but, when not feasible, a combination of Nb and V gives even better ductility. However, to be sure of avoiding transverse cracking in higher N steels a small addition of Ti is required. This resulted in a decrease in the fraction of fine particles and in accord with this better ductility. Transverse cracking of industrial slabs was then avoided.

Jan 1, 2011

By L. A. Vermeulen, D. D. Howat

New distribution functions are derived to describe the size distribution of grinding elements in ball mils. The formulations are based on the assumption that abrasive as well as impactive interactions occur during bal milling-an assumption that is supported by a large body of experimental evidence. It is shown that the functions can be used in the estimation of the magnitudes of abrasive and impactive components in the total rate of bal wear. The relative magnitudes of the wear components provide a basis for optimization of the chemical and metallurgical properties of the balls in a given milling situation. However, it is contended that these quantities are also useful indicators of the relative intensities of the abrasive and impactive interactions that are operative in the size reduction of mineral particles within ball mils. These quantities can be determined for any industrial ball mil, and their magnitudes provide practical guidelines for mil operation. The theory is used in an analysis of samples of ball charges from two industrial ball mils, and it is also applied to al the data on bal-size distributions found in the literature. The qualitative correlation between the calculated values of the wear components and the reported operating conditions is good for a variety of industrial ball mils, in conformity with the hypothesis that the relative magnitudes of the wear components are related to the milling conditions.

Jan 1, 1986

By A. J. Jager, G. R. Adams

The pattern of mining-induced fractures ahead of stope faces in deep-level gold mines, as revealed by petroscopic observations, is described. It is shown that there are zones of fractured and unfractured rock ahead of the face, which are about I m wide and continue as discrete entities for at least 12 m parallel to the face and at least 5 m vertically. These zones do not form continuously as mining progresses, but develop from time to time, leaving a solid zone between the fractured zones. The maximum depth of fracturing ahead of the face depends on the rate of energy release.

Jan 1, 1980

By J. T. Nel

The Kroll process is the traditional method of producing zirconium metal by reduction of zirconium tetrachloride with magnesium metal. This paper discusses the production of zirconium metal in a plasma reactor. Anhydrous low-hafnium ZrCl4 and Mg metal were fed continuously to a 30 kW non-transfer plasma reactor at a rate of 0.31 kg.h-1. Due to losses in the system the recovery of crude product was 77.5 %. After purification to remove unreacted feed material and MgCl2 by leaching, >98 % pure zirconium metal powder was obtained. The overall recovery of purified Zr was 74 %. The conversion efficiency of the process was 95 %.

Jan 1, 2012

By L. J. Park, A. D. Thomas

Gladstone Pacific Nickel Limited (GPNL) is proposing to develop the Marlborough nickel deposit in central Queensland and the Yarwun Refinery in Gladstone, Australia. The project proposes to connect the two sites with a DN 500, single pump station slurry pipeline, transporting up to 4 Mtpa of nickel laterite ore as slurry 180 km from Marlborough to Gladstone. Slurry viscosity is a key parameter influencing pipeline design. Not only is the slurry viscosity relatively high, requiring pumping at low concentrations, around 30% by weight, but the viscosity (yield stress and plastic viscosity) increases with shearing or agitation. It is argued that the viscosity changes can be analysed in terms of total energy input, including energy input during grinding. The slurry viscosity is therefore expected to increase along the pipeline and the pumping concentration must be low enough such that the increase in yield stress does not cause transition to laminar flow towards the end of the pipeline. The base viscosity of two ore types is determined using a rotational viscometer for minus 212 micron slurries. Viscosity variations with ore particle sizes of d99 212, 425 and 600microns are investigated. For each of these particle sizes the expected increase in viscosity during pipeline transport is simulated on a laboratory scale by agitation with a turbine mixer in a baffled container to give the same equivalent unit energy input as will occur in the pipeline. Tests were also conducted on the d99425 micron slurry in a 2.7 metre diameter DN 200Wheelstand, rotated for the 23 hour transit time and at a similar relative velocity as in the pipeline. Based on the Wheel stand test results the yield stress is expected to increase by a factor of 3.1during pipeline transit. The preliminary design allows for a reduced pumping concentration to accommodate this increase in yield stress towards the end of the pipeline.

Jan 1, 2007

By H. M. Friede, R. H. Steel

Tin mining and smelting in the Transvaal during the Iron Age by H. M. FRIEDE*. Ph.D. and R. H. STEEL* (Visitors) This paper reviews the historical, archaeological, and metallurgical evidence on Iron Age tin mining and tin smelting in Southern Africa. The results of the analysis of twenty samples of tin ore, tin slag, and tin ingots found associated with Iron Age materials in the Transvaal (mostly in the Rooiberg area) are reported and discussed. The types of ingots preserved in local collections are described. A small experimental tin-smelting furnace was constructed and worked according to traditional African Iron Age technology. Qualitative and quantitative results of this experiment are reported.

Jan 7, 1976

By P. K. Van Manen

Anglo Platinum?s Polokwane Smelter is situated outside Polokwane, in the Limpopo Province in South Africa. A single 168 MVA six-in-line rectangular furnace smelts dry concentrates containing platinum group metals (PGMs). Furnace energy consumption since commissioning is presented, showing that energy efficiency improves as capacity utilization increases. An energy balance for the furnace is outlined, indicating the measured or calculated energy losses from the hearth and side-wall cooling, the copper coolers, the upper furnace walls and roof, and the energy losses in off-gas, matte, and slag. From the energy balance, the potential to improve energy efficiency by controlling the slag temperature, the slag level, and the off-gas volume is derived. Furthermore, the impact on the energy balance of different concentrate types is discussed, as well as the potential impact of replacing all upper waffle coolers by plate cooler panels.

Jan 1, 2009

By R. J. Kriek, J. J. Cruywagen, W. J. Engelbrecht

Selective photo reduction, using the semiconductor TiO2 under UV irradiation, has been investigated as a possible recovery and/or separation method for the PGM's rhodium, palladium and platinum. The effect of pH value and concentration of the sacrificial reducing agent (ethanol) on the rate of reduction of Rh (III), Pd (II) and Pt(IV) ions have been determined separately for these ions as well as for some mixtures. Conditions favourable for the reduction and adsorption (or precipitation) on TiO2 have been established. It has been found that already deposited Pt or Pd metal promotes reduction of Rh (III) ions at a pH value where it would not otherwise be reduced. A method for the separation of a mixture comprising Rh (III), Pd(II) and Pt (IV), based on photo reduction and adsorption on the TiO2, is proposed.

Jan 1, 1995

By S. M. Bradshaw

In order to assess the requirements for online matching when using a transverse electric field (E-field) applicator to treat mineral ores continuously, the effect of varying load properties on matching has been investigated by simulation. The effective permittivity of the ore to be treated is expected to show variation on both short (< 1 s ) and long (minutes) time scales. By modelling the ore as a series of slices with alternating effective permittivity values, it was shown that permittivity variations on the scale of the expected particle size are attenuated significantly and matching is not required. For variations in permittivity on the length scale of the free-space wavelength, variations in reflected power are at most within ±10% of the mean. This is not considered operationally significant, as extreme permittivity variation over this length scale is unlikely, given the expected distribution of ore particle sizes to be treated. At typical ore transport speeds through the applicator, these variations occur on a time scale an order of magnitude shorter than the response time of typical industrial online matching equipment. This implies that online matching is neither required nor possible for short time scale variation. Long-term variations in dielectric properties can be adequately compensated for by current matching technologies. It is concluded that the transverse E-field applicator is robust to changes in the dielectric properties of crushed ores within the expected range of their variation.

Jan 1, 2012

By P. Greenfield

The German steelmaking industry has come up with a novel solution to the problem of waste plastics-grind them into particles and use them in the steelmaking process. Plastics make ideal agents for removing oxygen from iron ore in blast furnaces, and save on oil and coal as well. The aim of replacing heavy oil and coal with plastics in blast furnaces is to use them as reducing agents as well as an additional energy source.

Jan 1, 1996

By O. L. Papendorf

The method presented in this paper can be used, instead of lengthy cash-flow determinations, for the calculation of present values in the face of physical growth and inflation.

Jan 1, 1981

Ladies and gentlemen, it is a privilege to be able personally to welcome you to the opening of this Symposium. It is particularly pleasant to be able to extend a warm South African welcome to al our visitors from foreign shores. We trust you will enjoy your stay in our country. It is a singular honour for me to be present here today, and to have been asked to open this international Symposium. MINING IN SOUTH AFRICA Mining is the single most important contributor to this country&apos;s foreign-exchange earnings. Minerals and processed mineral products together account for about 70 per cent of South Africa&apos;s total foreign exchange earnings. The mining sector employs in excess of 670 000 people, and is one of the largest employers in the country. The construction and development of cities and towns like Johannesburg, Welkom, Orkney, Springs, Benoni, Witbank, and Klerksdorp is a direct result of the contributions of the mining industry to economic activity in these areas, as well as of the multiplier effect of secondary industries.

Jan 1, 1993

By A. W. de Villiers

This paper explores the behaviour of methane in the goaf during longwall mining, together with some methods for the control of methane emissions into the goaf, the working face, and the ventilation system. Experimental work done at Twistdraai Colliery, Sasol Coal, is referred to, as well as the gas-drainage system being practised at West Cliff Colliery in New South Wales, Australia. Gas drainage is discussed briefly, and certain suggestions are made in regard to coal mining in South Africa.

Jan 1, 1989

By P. W. Ocerbeek

The occurrence, properties, and uses of andalusite, and its advantages over other refractory minerals and materials, are discussed. Ore reserves are given for the five producing areas, and statistics on production, export sales, and prices are included to illustrate the growth of the industry since the early 1960s. The mining and beneficiation procedures are described, with special reference to new techniques in concentration and magnetic separation. As fines dumps represent a considerable source of andalusite, possible methods of recovery are discussed. . The outlook for the future appears favourable, and possible competition from other sources and substitute refractory minerals are mentioned. It is concluded that the industry is in a sound position to maintain South Africa&apos;s status as the world&apos;s foremost producer and supplier of andalusite.

Jan 1, 1989

By A. R. Barnes, C. W. P. Finn

The prereduction and smelting characteristics of UG-2 ore were studied and compared with those of Winterveld chromite ore. The UG-2 ore proved more reducible, and substantial prereduction (over 70 per cent reduction after 30 minutes at 1250oC) was obtained. No difficulty was experienced in the production oh high-carbon ferrochromium alloy containing 48 to 50 per cent chromium. Calculations of the energy balance show that UG-2 chromite has lower total energy requirements (both on the basis of unit of ferrochromium produced and of total chromium content). More than 50 per cent of the energy required for reduction can be supplied outside the smelting furnace.

Jan 1, 1983

By R. Sun, R. G. Gillies, R. S. Sanders, J. Schaan

The pipeline transport of paste, backfill or thickened tailings slurries is an important component of the tailings disposal process in many mines around the world. These mixtures contain significant fractions of fine (clay) and coarse (sand) particles, causing them to exhibit non-Newtonian flow behaviour and high frictional pressure gradients. There is often economic incentive to operate these pipelines in the laminar flow regime. Irrefutable evidence has shown that coarse particle settling can occur during the laminar flow of these slurries even when static settling tests show no indication of such behaviour. Previously, a ?rule-of-thumb? minimum frictional pressure gradient of ~1.5 to 2 kPa/m was suggested to ensure effective sand transport, based on the results of tests conducted using viscous Newtonian oils. In this paper, we examine the results of laminar flow tests of non-Newtonian, coarse-particle laden slurries conducted with pipeline loops of 50, 100, 150 and 250 mm in diameter. The results indicate that the ratio of the mean wall shear stress to the mean surficial particle stress is abetter indicator of laminar flow settling tendency than frictional pressure gradient.

Jan 1, 2007

Notices THE FEDERATION OF SOCIETIES OF PROFESSIONAL ENGINEERS The following letter has been received from the Secretaries of the above Federation. Ref. EHvdL/MM/27 13/11/1973 TO THE SECRETARIES OF ALL MEMBER AND AFFILIATE SOCIETIES Dear Sir/Madam, ENTRIES IN TELEPHONE DIRECTORIES PAPERS OF INTEREST The following recently published papers may be of interest to memo bers. DIE FEDERASIE VAN VERENIGINGS VIR PROFESSIONELE INGENIEURS Die volgende brief is van die Sekretarisse van die bogenoemde Federasie ontvang. verw. EHvdL/MM/27 13/11/1973 AAN DIE SEKRETARISSE VAN ALLE LlD- EN GEAFFILIEERDE VERENI GIN GS Geagte heer/dame,

Jan 1, 1974

By C. P. Smyth

Large volumes of quantitative geochemical data, presenting a formidable interpretation task to geologists, are generated in the course of exploration drilling for new ore deposits. The incorporation of geological expertise into computer programs developed for the interpretation of this data would improve the speed and accuracy with which it is interpreted. A detailed analysis of the geochemical log interpretation problem, together with a survey of relevant research in Artificial Intelligence and petroleum well- logging techniques, confirms, that artificial intelligence, particularly as developed in the fields of expert systems and pattern recognition, provides techniques for implementing such data interpretation programs. In addition, it provides data analysis techniques significantly more powerful than those currently applied to geochemical data, and very appropriate to the hypothesise and test&apos; character of mineral exploration problem-solving. The conversion of raw borehole log data to meaningful higher level geochemical entities, in terms of which geological reasoning may take place, is a critical step in applying these techniques to log data analysis. A method of achieving this conversion as an exercise in signal-to-symbol transformation is presented.1

Jan 1, 1987

By X. W. Pan

It has been found that the MnO content of a slag decreases sharply when direct current is applied to a 1T1£tal-Slagsystem consisting of liquid Mn-Si-Ccsat metals and MnO-SiO2-CaO-AI203 slag in graphite crucibles. This paper reports a preliminary investigation into the electrochemical effects of direct current on the metal-slag system, the silicon content of the metals, and the MnO content of the slag. The results show that, when a direct current of 7 A is maintained, the MnO content of a metal containing 10 to 11 per cent silicon by weight is reduced rapidly from 26,5 to 17,2 per cent by weight. This reduction seems to proceed further when the process is continued. When the direct current and the voltage are kept constant at TA and 4 V respectively, the MnO content of a metal containing 1 to 2 per cent silicon by weight is reduced to 1 from 25 per cent by weight, which results in a manganese yield of 96 per cent.

Jan 1, 1995

By K. R. Noble

The planned extraction of the No. 1 shaft pillar at Blyvooruitzicht Gold Mine highlighted a number of potential problems. In spite of the relative shallowness, careful thought had to be given to stope phasing owing to the detrimental effect of the anticipated geology and the fact that uninterrupted hoisting was necessary. Extensive use was made of computer modellig to design the stope phasing, determine the influence of regional support and to predict the direction and magnitude of displacements in the shaft. The paper describes the success of this design approach, and measured displacements in the stoping horizon and shaft barrel are compared to those obtained from the original computer model

Jan 1, 1987