Search Documents

By K. R. Vost

This paper reviews the theoretical methods used in South Africa for the prediction of heat pick-up and air-temperature gradients along main haulages. These methods include those of Starfield, Ramsden, McPherson, and Goch and Patterson. The differences in predictions based on typical airway conditions are explained as being due to differences in the mathematical models on which the predictions are based. The largest discrepancies were found for dry airways and for airways with bulk air coolers. The errors in predictions of the effect of machines and coolers that have been running for only a few months are calculated, and the limitations of various simplified methods are discussed.

Jan 1, 1982

By R. H. Steel

Ingot casting and wire drawing In Iron Age Southern Africa by R. H. STEEL (Visitor) This paper describes the experiments that were conducted in 1974/1975 on two related aspects of Iron Age copper technology in Southern Africa: ingot casting and wire drawing. Three types of ingot were successfully cast: the St Andrew's Cross ingot, the marale ingot, and the musuku. It is suggested that the 'studs' on the musuku are not the remains of broken-off rods as previously proposed by other investigators, but that the ridged pattern is an ornamental feature. Copper wire was successfully drawn with similar tools and according to the procedures described in the literature on African Iron Age wire drawing. It is concluded that these accounts are generally accurate and that the pre-European metal workers are worthy of respect for the results they achieved with primitive methods.

Jan 11, 1975

By H. E. James

During the past ten years there has been an upsurge of interest in the development of selective ion exchange resins and solvents, and of ion-exchange and solvent extraction equipment tailored to the special requirements of mineral-processing circuits. It is therefore not surprising that the recent Symposium on Ion Exchange and Solvent Extraction in Mineral Processing, held at the National Institute for Metallurgy (NIM) on 7th and 8th February, 1980, was a resounding success. This Symposium, organized jointly by NIM. Ion exchange and solvent extraction The Symposium on Ion Exchange and Solvent Extraction in Mineral Processing, which was organized jointly by the National Institute for Metallurgy, the South African Institution of Chemical Engineers, and the South African Institute of Mining and Metallurgy, was held in Randburg on 7th and 8th February, 1980. Analytical chemistry The Fifth International Conference on Analytical Chemistry, organized by the Chemical Society, is to be held at Lancaster University, England, from 20th to 26th July, 1980. Coal mining The First International Symposium on Thick and Steep Seam Coal Mining will be held in London from 18th to 21st May, 1980. Mineral processing The XIV International Mineral Processing Congress will be held in Toronto from 10th to 16th October, 1982. The theme of the congress will be 'Worldwide industrial application of mineral processing technology'. Sessions will be held on the following:

Jan 1, 1980

By P. S. Turner

After a brief account of the differences between the control of underground fires and those on the surface, the paper describes the analogue detection system used on the mines of the Anglo American Corporation of South Africa Limited. The system comprises Spanair gas analysers, Becon combustion-particle detectors, a telemetering system, a surface signal-recording and-processing system, and an alarm system. The use of the system is described and illustrated.

Jan 1, 1982

By K. Sasaki, Y. Oriia, Shigeto Kuroiwa, H. Miki, Yuji Aoki, T. Hirajima, G. P. W. Suyantara

The effect of a sulfite reagent on the floatability of chalcopyrite and enargite was investigated in this paper. The flotation tests using single and mixed minerals were performed under various concentrations of sulfite. The flotation tests using a single mineral showed that the sulfite reagent depressed the natural floatability of both minerals at pH 9. Surprisingly, enargite was floated after the addition of potassium amyl xanthate (PAX) following the sulfite treatment, and the floatability of chalcopyrite depressed under a similar condition. X-ray photoelectron spectroscopy analysis results showed that the sulfate species increased after the sulfite treatment on both minerals. However, the addition of PAX removed this sulfate species and rendered the enargite surface hydrophobic. This phenomenon was not observed on the chalcopyrite surface. FTIR analysis and PAX adsorption studies were performed to support this finding. The flotation of a mixed mineral was in agreement with the flotation of a single mineral, indicating a possibility for selective flotation of chalcopyrite and enargite using the proposed method. Keywords: Flotation, chalcopyrite, enargite, sulfite, potassium amyl xanthate

Jan 1, 2020

By P. Kind

Design criteria and recent developments in large-capacity Wemco flotation cells by P. KIND, Ph.D. (Clausthal), B.Sc. (Visitor) The scaling-up of the large flotation cells that have been developed during the past few years has been based on hydrodynamic considerations and has resulted in a 500 ft3 cell unit. Plant results on a porphyry copper ore show that the 500 ft3 unit is equivalent to the previously used 300 ft3 model.. . Plant tests on the use of 300 ft3 flotation cells for the recovery of phosphate, particularly from the coarse size fractions, are also described.

Jan 3, 1976

By S. K. Gilman, P. S. Marcos

There are basic areas of importance within a concentrator or mineral separation plant, which require focus to ensure acceptable recoveries, throughputs remain at an acceptable level and product grades meet specification. Professional and para-professionals within the mineral sands industry are in demand due to the booming resource sector. Added to this, new mineral sands operations are being commissioned straining the industry further. These factors have increased staff turnover and introduced many new people to the industry. It is essential these new entrants are armed with basic plant troubleshooting skills relevant to the minerals sands industry to minimize production lost through poor recoveries. Mineral sands processing does not involve highly technical or sophisticated unit processes. However, success is often slow to arise due to a lack of detailed understanding, as well as managing multiple interrelated unit processes within a plant. Fundamental background physical conditions (such as equipment loading and water quality) must be met for unit processes to be efficient. Technical management of these process plants should always include observation of these background conditions for they often provide the answer to underperformance. Examples are presented with an indication of the possible effects on recovery and product grade.

Jan 1, 2007

By J. Abdollahisharif

Optimal cut-off grade is one of the most critical parameters in open-pit mine design because it defines the ore and waste and thus determines the maximum net present value possible from the mining operation. Although the algorithm presented by Lane (Choosing the optimum cut-off grade. Colorado school of Mines Quarterly, vol. 59, no. 4, 1964. pp. 811-829) is the most common one in the literature, it does assume constant capacities of the mine, processing, and refinery. In this paper, Lane's original algorithm has been modified to consider variable processing capacities in order to determine the optimal cut-off grade in open-pit mines. The new algorithm proposed here is compared to both Lane's original algorithm and to a previous modification that incorporated rehabilitation costs into the cut-off grade estimation. The algorithm proposed here that permits variable processing capacities is shown to be superior for the determination of optimal cut-off grade to both these previous versions. In addition, a computer-based program was developed in Microsoft Office Excel© to calculate the optimal cut-off grade as proposed here.

Jan 1, 2012

By deur A. P. van Wyk

Die Spesialistegroep, Materiaalingenieurswese van die Pretoria-gebied, het op 25 November 1981 'n baie geslaagde colloquium te Universiteit van Pretoria aangebied met die tema 'Oppervlaktebedekking van Metaalonderdele'. Die besprekings is ingelei deur mm. George Murray van Projects Expedited met sy lesing getiteld 'Surfacing by Welding'.

Jan 1, 1982

By C. Montoya

This paper shows, through a case study, the impact of multivariate grade modelling upon mine design and mine planning. A deposit explored by drill holes is considered, in which the grades of five elements (copper, silver, molybdenum, arsenic, and antimony) are of interest. Forty alternative models of the deposit are constructed by fitting the joint correlation structure of the grade variables and using conditional cosimulation. In addition, a reference model, obtained by averaging the alternative models, is also considered. The study shows that the resulting mine design (final pit characteristics and production schedules) is sensitive to the grade model under consideration, and that the design based on the reference model may not be optimal when compared to the alternative models based on cosimulation. However, when assuming a given long-term plan and extraction sequence, the grades and net present value (NPV) calculated on the reference model are unbiased with respect to those calculated on the alternative models with the same extraction sequence. The latter allow assessing the possible dispersion of the actual grades and NPV around their expected values, and are useful for the planner in order to determine the probability of meeting given production targets and of exceeding or falling short of given threshold grades. Additionally, unlike cosimulation, the separate simulation of each grade variable leads to unrealistic resource models and to biased results in mine design and mine planning. This approach should therefore be avoided, unless the grade variables are spatially uncorrelated.

Jan 1, 2012

By C. R. Speers

The induced elastic stresses in the sidewalls of gold-mining tunnels at a depth of 4000 m in the Witwatersrand exceed the peak compressive strength of even the best-quality quartzite rocks. Laboratory tests measuring post-yield stress versus strain response show that brittle fracture occurs, followed by a loss in strength associated with strain-softening behaviour. Numerical modeling based on an assumed Mohr-Coulomb criterion fitted to the test results shows that large ongoing deformations of the sidewall occur, leading to total tunnel failure without adequate support. A methodology is presented to enable a quick assessment to be made of support requirements in terms of ground characteristic curves for numerically derived pressure versus displacement. From these curves, estimates can be made of the force levels for cable bolting and of the thickness and strength requirements for shotcrete linings. As an example of its application, the methodology is used in a comparison of the relative stability efficiencies of a square-shaped tunnel and a horizontal ellipse-shaped tunnel.

Jan 1, 1996

By R. P. Plasket, D. A. Ireland

Ancillary smelter operations and sulphuric acid manufacture at Impala Platinum Limited by R. P. PLASKET. Pr. Eng.. M.Sc. (Chem. Tech.). Natal (Fellow) and D. A. IRELAND. Pr. Eng.. B.Sc. (Chem. Tech.). Natal (Member) The de-watering, spray drying, and converter operations at Impala are described, aspects that may be new to the minerals industry in South Africa being elaborated. Air-pollution control necessitated the installation of a sulphuric acid plant to limit the emission of sulphur dioxide to the atmosphere. Closer control of the smelting and converting operations was required for successful operation of the acid plant on the inherently Iow and varied concentration of feed gas from converter blowing. Approximately 82 per cent of the sulphur entering the smelter is converted to sulphur dioxide, of which 67 per cent is fed into the sulphuric acid plant.

Jan 8, 1976

By A. H. Swart, M. F. Handley

Unplanned stope panel collapses occur on most near-surface and shallow mines in South Africa. Although these incidents often occur during blasting, they pose a major threat to the safety of underground workers and the economic extraction of orebodies. Most stope panel collapses occur due to excessive panel lengths that are not designed according to a systematic design procedure or methodology. Instead, panel lengths are often dictated by the equipment in use and by previous experience under similar conditions. Hence, a rock engineering design methodology for the design of stable stope panels between pillars is of vital importance for optimum safety and production in shallow mining operations. Using the proposed design methodology described in this paper, rock mechanics practitioners and mine planners should be able to identify and quantify the critical factors influencing the stability of stope panels. The critical factors should then be used as input to the design of stable stope panels that will provide the necessary safe environment for underground personnel working in stopes. The proposed design methodology is an iterative process, which includes aspects such as rock mass characterization, estimation of rock mass properties, identification of potential failure modes, consideration of appropriate stability analyses and other elements of the rock engineering design process. This process continues after implementation. During monitoring, new data should be included in the database and the design process repeated on a regular basis. Design approaches included in the proposed design methodology include empirical methods such as different rock mass classification methods, analytical methods such as elastic and Voussoir beam analyses, kinematic analyses, probabilistic analyses, and numerical analyses. Keywords: stability, stope panels, design methodology, hard rock mines, shallow mining operations

Jan 1, 2004

By B. Strohmeier

The role of large, ultra-high-powered arc furnaces in a fully integrated steelworks for the production of flat products is outlined, and an account is given of the technological improvements that have been implemented over the past few years to enable the arc furnace to remain competitive against the conventional route using blast furnaces and top-blown-oxygen steelmaking (LD). Modern secondary refining facilities have been installed, enabling the arc furnace to operate at high production rates in the manufacture of high-quality flat products.

Jan 1, 1985

By S. R. Xie, S. Gong, E. P. Li, S. S. He, Y. J. Sun, S. J. Li

"Based on the complicated geological production conditions and abnormal strata behavior of the fully mechanized caving face No. 102 in the Xinyang Coal Mine, we analyze the breaking and forming process of distinguishing key block structures in close spaced coal seams. This analysis establishes an integrated mechanical model of these distinguishing structures. Furthermore, the horizontal force TAB generated by downward key blocks A and B is quantified, as is the Pressure PG exerted by key block B on caved gangue. Finally, the interaction mechanism is revealed. Analysis of the results using Mathematica reveal the following: 1. Both TAB and PG exhibit approximately inverse relationships to coal pillar width b; 2. TAB exhibits an approximately exponential relationship with mining height M of which the base is greater than 1; 3. PG exhibits an approximately arctangent relationship with mining height M. Combining these results with field observations, we conclude that the area in the vicinity of supports 100#–120# in the upper area of working face No. 102 is the likely zone of abnormal strata behavior. Thus, this area was classified as a key control area. Based on these results, the graded support control technique is proposed. Application of this technique in the field resulted in a reduction in the rate of hydraulic support system malfunction from 47% to 7% in the key control area. In addition, during times of periodic mining pressure, the roof caving height value never exceeded 0.3 m and the maximum spalling depth never exceeded 0.2 m. Overall, the results indicate that this new technique has markedly increased the stability of surrounding support rock material. IntroductionClose-spaced coal seams are widely distributed in China, and mining proceeds from the uppermost to the lowermost seam (Zhang et al., 2008). In the case of coal seams in close proximity, a particular set of risk factors becomes pertinent. These include disturbance of lower seams during the mining of overlying ones and the decrease in mechanical stability of lower coal seams following repeated movement of key blocks in main coal seam roofs. This inevitably results in behaviour such as heavy wall spalling and support damage to fully mechanized caving faces in lower-lying coal seams, which necessitates a significantly increase in the measures to support surrounding rock material (Zhang et al., 2010; Huang et al., 2013; Xie et al., 2013)."

Jan 1, 2016

By E. -U. Reuther

To improve the climatic environment underground the German coal mining industry has installed refrigerators with a capacity of 300 MW cooling power. One third of this total is accounted for by central refrigeration plants with more than 5 MW capacity. The central refrigeration comprises three stages: mechanical cooling, transport and distribution of chilled water via pipelines and exchange of heat in the air coolers. Of these three stages only the mechanical generation of chilled water has been resolved satisfactorily. Transport (including distribution) and exchange require further technical research. The Mining Institute of the Aachen University of Technology has done extensive studies on this subject, concentrating on controlling the flow of chilled water according to demand in the mine. Additionally, the favourable exchange in the air coolers is taken into account. The studies are based on a model mine which simulates the conditions in deep coal mines in Germany. The simulation program represents firstly the condition of the mine air at the location of the air being cooled, then the heat exchange in the air cooler itself, and finally the transport of the chilled water from the central refrigerator to the consumer. The program also reproduces the seasonal and operational changes in conditions of mine air as well as different air cooler designs. A regulated distribution of chilled water is also suggested. Finally, estimations of costs can be made as an aid for further planning.

Jan 1, 1987

By A. P. Van Wyk, G. Pirnaar

The effect of vanadium on the susceptibilities of chromium and chromium-nickel steels to reversible temper embritlement was evaluated. The steels investigated were approximately equivalent to steels of as 970 Grade 708A42 and as 970 Grade 817M40, the major difference being that molybdenum had been replaced by vanadium in various concentrations. It was found that the vanadium had a detrimental effect and, in al the concentrations tested, enhanced the susceptibility to reversible temper embritlement of both the chromium and the chromium-nickel steel. The detrimental role played by vanadium in reversible temper embritlement is explained by a consideration of the effect of vanadium carbide, as well as of free vanadium, in solid solution in ferrite.

Jan 1, 1987

By M. J. Santofimia

Multiphase microstructures in steel have been intensively studied in the past years, but combining non-equilibrium phases still offers a great potential for further development of these steel grades. Thus, improved combinations of mechanical properties can be obtained with microstructures formed by bainite or martensite, in combination with retained austenite. In particular, microstructures on the basis of carbon-depleted martensite and retained austenite can be produced by the very promising production process named quenching and partitioning (Q&P). Originally, the Q&P process aimed to avoid the formation of bainite during the heat treatment. However, the process does provide the possibility for (carbide-free) bainite formation during the partitioning step, i.e. in the presence of martensite. This article evaluates this approach, considering thatthe formation of bainite from austenite is strongly influenced by the preceding formation of martensite. Although the accelerating effect of the presence of martensite during bainite formation has been observed, it is not yet fully understood, and experimental and theoretical studies are being performed in order to come to a more effective exploitation of these processes for the formation of multiphase microstructures.

Jan 1, 2013

This paper presents recent advancements in the MillMapper software technology, developed and used for thickness gauging of liners of cylindrical grinding mills used for mineral comminution. MillMapper uses calibrated laser scanner data captured inside a mill to determine thickness at several million points on all liner surfaces with millimetre accuracy. The paper is structured as follows. First, a review of the technology and its numerous advantages over existing techniques and the value it adds to operations are presented. These are followed by discussion of recently-implemented innovations, including improved visualisation and inspection tools, automatic ball charge volume measurement and automatic mill liner volume/weight measurement. Results from its application at several sites in Australia are presented throughout.

Jan 1, 2007

By T. O. Hagan

A system for the monitoring of micrcoseismic events. which is designed for use in feasibility studies of rock-burst prediction, has been operating at Western Deep levels Limited since 1977. Analyses have revealed that the presence and Orientation of geological discontinuities ahead of the mine face can be predicted from the data produced by this system.

Jan 1, 1981