Search Documents

By J. W. Drelich, H. Zeng, L. Xie, X. Cui, Z. Gao, M. Tian, Y. Hu, W. Hu, W. Sun

Flotation is a mineral separation technology that uses the surface hydrophobic difference of valuable minerals and their associated gangue minerals to separate them. The flotation collector adsorbs on the valuable mineral surface to improve its hydrophobicity, and metal ions are usually used as activators to enhance the collector adsorption. Different mineral surfaces show different charging properties and adsorption behaviours with the collector or metal ions. Moreover, the order of adding metal ions and the collector also show significant and different flotation performance for the same mineral. The adsorption or flotation behaviour or both are governed by mineral surface chemistry, such as surface charging and reactivity. In our recent studies, force measurement using atomic force microscopy (AFM) was employed to study the surface charging and adsorption mechanism of metal ions and collectors. By preparing collector-functionalised AFM tips, AFM can directly measure the adsorption strength of the collector on the mineral surface to determine the anisotropy of mineral surface reactivity. The preparation of collector-functionalised AFM tips provides the foundation for further study of the activation role of metal ion in the collector adsorption. The application of AFM for force measurement in the surface chemistry of mineral flotation can provide important information on developing flotation reagents and lays the foundation for the specific regulation of mineral surface characteristics. Keywords: Scheelite; flotation; surface chemistry; AFM force measurement

Jan 1, 2020

By D. V. J. W. Groenewald, T. M. Louw, L. Auret, S. M. Bradshaw, A. V. Cherkaev

Unexpected equipment failures lead to financial losses due to production disruption. Time-based maintenance, based on checks over regular time periods, has been employed to minimise disruption. However, the improvements it can offer are limited as it may lead to unnecessary service of healthy equipment or missed failures occurring between service intervals. Condition-based maintenance (CBM) provides a further improvement to equipment reliability by detecting faults and predicting remaining useful life (RUL) based on equipment health monitoring. Its application in the mineral processing industry is hindered due to the high cost of health monitoring equipment. In this study, two stochastic process models, the adaptive auto-regressive model and the gamma process, are compared in their ability to forecast the degradation state and to provide RUL prediction. The gamma process model was found to be effective in both tasks. Due to its simplicity and minimum hyperparameters requirements, it is proposed to use the gamma process as a baseline for comparison with other models. Keywords: Condition-based maintenance, remaining useful life, slurry pump, adaptive autoregressive mode, gamma process

Jan 1, 2020

By M. Yavuz

Equipment selection in mining operations is an important issue, and also difficult to solve in multiple criteria environments. The paper in question has aimed to develop computer software for solving equipment selection problems in mining. In their paper, Basçetin et al. have analysed two case study problems related to open pit and underground mining method selection. By using Yager?s method1, the authors have selected 18 different criteria in the first case study and 21 criteria in the second case study. However, as emphasized by Ozdemir2, in pair wise comparison matrices the appropriate number of criteria should be seven as the maximum, from the point view of validation, consistency and redundancy. In cases where there are more than seven criteria to be handled, it is suggested that the criteria should be clustered and then the maximum number of clusters and subcriteria of every cluster should be limited to seven4.

Jan 1, 2007

By Y. Jiao, V. S. Thompson, D. W. Reed, Y. Fujita, J. E. Aston

Rare earth elements (REE) are vital components in modern electronics and green technology products. Supply is tight and global demand is expected to increase, leading to high risk for the economic and national security of countries largely dependent upon foreign supplies. Recycling of REE from consumer and industrial waste materials is a possible way to help meet demand. We have shown previously that biohydrometallurgy can play an economically and environmentally sustainable role in REE recycling, particularly if agriculture or food wastes are used to produce organic acid bioleaching agents. A challenge for organic acid-based bioleaching is the incomplete conversion of the carbon substrate to an optimal organic acid biolixiviant with high REE extraction capability from a variety of REE-containing feedstocks (e.g., mining wastes, magnets from end of life products, spent batteries, etc.). To help meet this challenge a metabolic model was developed for Gluconobacter oxydans to identify options for improving sugar conversion to organic acids. Model predictions were consistent with laboratory data for the microbial consumption of glucose and production of gluconic acid, and suggested that providing growth conditions with relatively high C:N molar ratios could result in lower pH biolixiviant production and thus improve bioleaching. Keywords: Gluconobacter oxydans, bioleaching, metabolic modelling, rare earth elements summaries 2019: U.S. Geological Survey, 200 p., https://doi.org/10.3133/70202434.

Jan 1, 2020

By X. Zhang, E. Li, Y. Xiao, Z. Yu, H. Han, J. Xie, J. Tian, W. Sun, K. Hong

In a pulp environment, the surface properties of magnesite and dolomite tend to be similar, due to the re-adsorption of dissolved calcium species, which makes the flotation separation difficult. In this paper, the chelating reagent EDTA is introduced to eliminate the adverse influence of the calcium species and to restore the selectivity of magnesite-dolomite separation using sodium hexametaphosphate (SHMP) as a depressant. Flotation experiments confirm that the recovery of magnesite improves significantly in the presence of EDTA. Zeta potential experiments confirm that the negatively charged EDTA4+ and HEDTA3+ species can form soluble and stable chelates with positively charged Ca2+ and Ca(OH)+ species preventing their adsorption on the magnesite surface. Adsorption measurements prove the addition of EDTA can decrease the adsorption of depressant SHMP on the magnesite surface. X-ray photoelectron spectroscopy (XPS) measurements further confirm the transformation from the surface of magnesite to dolomite in the presence of calcium ions, and the possible adsorption mechanism of EDTA and SHMP on the magnesite and dolomite surface. Key words: Magnesite; Dolomite; Surface dissolution; Flotation separation

Jan 1, 2020

By W. J. Kempson

As a result of the rising electrical energy costs in South Africa, a method was sought to reduce the overall electrical consumption of typical shaft systems. A typical shaft configuration was analysed and the primary energy consumers were identified. The ventilation fans for this system were found to consume 15% of the total energy of the shaft system. It was calculated that more than 50% of this energy is consumed by the shaft itself, more specifically, by the pressure losses that occur in the shaft as the ventilation air passes through it. In order to ensure that the theory being used for the evaluation of these shaft systems is accurate, a total of five shafts were instrumented and the actual pressure losses over the shafts plotted against time. These shafts were then analysed from a theoretical perspective. Finally, in order to ensure a thorough understanding of the behaviour of the ventilation air in shaft systems, the systems were simulated using computational fluid dynamics (CFD) techniques. There were significant discrepancies between the theoretical analysis and the CFD simulation during the initial comparisons. This discrepancy lessened as the complexity of the CFD models increased, until when the complete shaft was modelled using the full bunton sets, the pipes, and the flanges, the difference between the theoretical evaluation and the CFD simulation was small. This result demonstrates that the theory is insufficient and that the interrelated effect of the buntons and fittings has not been fully appreciated by current theory. The final phase of the work presented here was to evaluate the costeffectiveness of using different bunton shapes and shaft configurations. It is shown that the increase in the pressure losses and therefore the direct operating costs of the shaft can vary by as much as 80%, depending on the bunton configuration chosen. The placement of the piping in the shaft can increase the pressure losses, and therefore the direct operating costs of the shaft, by as much as 12%, depending on the placement of the piping in the shaft; this effect includes the use of flanges. The use of fairings on a large cage can reduce the resistance that the cage offers to the ventilation flow by as much as 30%. This, however, does not translate into a direct saving because as the cage moves through the shaft, the overall effect is transitory. These savings can be significant when the items highlighted in this work are applied correctly. Keywords shaft design, ventilation, energy consumption, modelling, CFD.

Dec 1, 2013

The visit which took place on the 18th February, 1972 was a departure in that the places visited had no direct connection with the work in which members of the Institute are normally engaged. It was refreshing and stimulating to see important and involved operations normally outside ones own trend of life and to have experts to speak about technical, financial and matters of general interest concerning their work, not forgetting their troubles and problems and how they overcame them. Carlton Centre The members of the Institute were received by Mr D. Appleton, Public Relations Officer of the Carlton Centre Limited, who introduced Mr L. R. M. Fee of W. Rhodes Harrison, Architect in charge of the project; Mr W. C. E. Skilton of Murray and Roberts, the Engineer in charge of the construction of the complex and Mr A. Home the Senior Operating Engineer of Carlton Centre Limited. Each of these gentlemen addressed the members giving short rundowns on the project with special reference to their particular sphere of the undertaking. A variety of particularly interesting statistics relating to the planning construction and the ultimate operation and maintenance of the complex was given. Mining engineers present had an opportunity to compare the problems encountered by them associated with depth to problems encountered by the civil engineer in the construction of a building rising to such an enormous height. To some of the members a sense of similarity of the labour problems encountered must have been recognised. After tea the visitors were divided into groups, each under the guidance of an official, and then visited the highest floor accessible and thereafter the 19th floor where the internal arrangements for airconditioning, lighting, plumbing, power supply and communication arrangements were explained. Thereafter a visit to one of the seven basements which houses all machinery required to serve this enormous complex enabled the visitors to see the standby power arrangements as well as the refrigeration plant. The visit finished in time to proceed to the Crest Hotel in Hillbrow for lunch. To our hosts for the visit to the Carlton Complex a special vote of thanks is recorded. Strydom Tower In the afternoon the party proceeded to the Strydom Tower where Mr Knight from the Public Works Department who was the Engineer in charge of the construction of the tower gave details on the construction and the extraordinary methods which had to be adopted to achieve the desired objectives and to overcome known as well as unforeseen difficulties. The comparatively short time taken to complete the project and the good safety record appeared to impress the visitors. The final phase of the visit was taken care of by Mr Bothma of Telecommunications Department of the Post Office, who gave an extremely interesting explanation of the telecommunication organization of the Post Office with particular reference to the part the Hillbrow Tower plays in the South African telecommunication system. Both gentlemen answered many questions willingly and interestingly. Following the explanatory talks the visitors were shown the technical equipment housed in the two top levels of the tower. Short explanatory talks gave members an insight into the workings of one of the most important aspects of modern life. Even to the amateur photographer opportunities existed to view and photograph the city from the highest available observation point. We are indebted to Mr Gouws, the Regional Director of the Post Office for granting permission to visit sections of the tower normally not accessible to the general public and to our hosts for the manner in which we were received and entertained on the explanation of the many interesting features of this important installation. In conclusion, the programme for the day can be classified as interesting, of exceptional educational value, and an opportunity to see something of the engineering skills put into two vast and ambitious undertakings and the results achieved.

By Dhananjaya Senapati, E. V. S. Uma Maheswar, C. R. Ray

Carbothermic process of Ferro Silicon production is primarily a slag-less process. However, slag formation is observed in the regular operation as experienced by almost all the Ferro Silicon Producers in different pro-portions. The problem of slagging in the furnaces may be due to: a)Variation in the input burden charge material quality b)Fluctuations in the Carbon balance and/or c)Fluctuations in the Electrode penetrations The problem will be more severe in nature with the increase of the size of the furnace. The operation performance of the furnace gets badly affected if the slag formed in the furnace is not removed from the bath in time and to the maximum extent possible. It is, therefore, very essential to know the characteristics of the slag formed in the Ferro Silicon Furnaces, besides eliminating the very cause of formation itself; and to find the routes of draining of the same from the furnace bath effectively. This paper envisages the effects of using the LIME STONE in the Ferro Silicon Burden in stabilizing the 48MVA Furnace for improved performance and better consistency. Quality fluctuations in the available Raw Materials are compared with that of the requirements for the Ferro Silicon production. The furnace operational data is compared for 12 months period each for the period corresponding to the before and after usage of lime stone in the burden and found encouraging results in the performance. Implications of use of Lime Stone in the burden on the quality of the output alloy are also studied.

Jan 1, 2007

By F. L. D. Cloete, M. C. Coetzee

This study was aimed at a comparison of the efectiveness of a new axial-flow type of mixer impeller (the Prochem design) with the traditional inclined-blade turbine. The intended application of the mixers was in carbon-in-pulp plants for the extraction of gold from cyanide-leached pulps. The first part of the project involved water and ion-exchange resin, and measurement of the power drawn by the various sizes of impeller to fully suspend the resin. The rate of reaction between the resin and the solution was measured as a function of the power input to the mixer. In the second part of the project, use was made of activated carbon, silver cyanide solutions, and ore pulps. The rate of absorption of silver from the solutions and pulps was determined, as well as the rate of attrition of the activated carbon caused by the various impellers in clear water. The Prochem design of axial-flow impeller was shown to fully suspend solids at only one-quarter of the power requireabyan inclined-blade turbine of similar size. The axial-flow pattern produced was responsible for the more uniform vertical concentration profile of suspended beads produced by the Prochem design. These measurements verified the observations of other researchers that the rate of reaction is not affected by the ;design of impeller provided that al the solids are fully suspended. The Prochem design of impeller therefore achieved the same reaction rate as the conventional turbine at a quarter of the power input. The atrition rates of activated carbon could be correlated, in terms of the energy absorbed, by the same equation for al the impellers. Higher concentrations of activated carbon increased the amount of carbon fines produced. These results emphasize the importance of designing mixers for minimum power consumption.

Jan 1, 1989

By M. Gershon

During the exploration phase of mine development, drilling location is in the hands of the geologist, and drilling is spread over the entire domain of the property or deposit boundary. During the mine planning and production phases, however, the mining engineer also needs to use the information obtained from the drilling program. Thus it is important that he/she have some input into the selection of the drillhole locations. Usually, when exploitation will center on one portion of the property for the immediate future, the mine engineer will want to have more of the drilling performed in this area. In the early stages, the purpose of the drilling was to make a decision concerning whether or not to develop a mine. Once the decision is made to proceed with this development, the mine engineer needs to know, with as much confidence as possible, the estimate of the ore grade at each location where mining will occur. This paper addresses the problem of drillhole location for the needs of the mining engineer. The goal is to compare a variety of approaches to drillhole location with a new approach developed by the author. This approach is based on the theory of geostatistics, with the estimation variance used as the quantitative measure of the confidence attained. The goal of the algorithm is to select those locations that minimize the estimation variance subject to constraints on the number of drillholes and the total cost of the drilling program. The kriging equations are used as another set of constraints. The resulting nonlinear optimization model is expressed in terms of binary (0 - 1) decision variables leading to a solution by the branch-and-bound procedure. The algorithm has been applied at a number of operating properties, and practical results and suggestions for implementation are provided.

Jan 1, 1987

By J. Levin

Bond's Standard Work Index (SWi) indicates the grindability of an ore, and his Operating Work Index (OWI) indicates the performance of a grinding mil or circuit. The comparison of the two indices offers a measure of the efficiency of the grinding operation. Mil (or circuit) performance, particularly on the Witwatersrand, is often indicated by the index kilowatt -hours per tonne of minus 75 µm material produced (kWh/t minus 75µm or OE75)' The paper shows that a standard kWh/t minus 75 µm index (SE75) can be obtained from the standard Bond grindability test (which provides the SWi), and asks whether the two E75 indices can be used in the various ways in which the two Work Indices are used. For the answer, the paper presents averaged values for the standard grindability indices of the gold ores of the Witwatersrand, averaged values for the performance of grinding mils operating on those ores, and the results of laboratory grinding tests on a composite of several Witwatersrand ores. The particle-size indicator for the calculation of the Wi indices, the am size, is constant in its relation to the largest particles present, whereas the percentage minus 75 µm, the indicator of size for the E75 index, varies with the degree of grinding in its relation to the size of the largest particles. Because of this difference, the standard Work Index increases as the grind becomes finer, whereas the standard kWh/t minus 75 µ value decreases. The Wi and E75 indices nevertheless serve similar purposes when applied to moderately fine grinding-finer than 70 per cent minus 75 µm. Open circuit laboratory grinding tests revealed three stages in the grinding process, and credible values for the open circuit Work Index were obtained only from the second stage. The conversion of the open circuit Work Indices to the equivalent of close circuit indices by the application of Bonds open circuit inefficiency factor (a constant for grinds indicated by the d80 size) was of limited success; however, the development of a conversion factor related to particle-size should not be difficult. Initially difficulty was experienced in the calculation of the 0E75 indices from the results of the laboratory tests, but it was eventually considered that a constant value of the index derived from the results would be close to the true open-circuit index. The open-circuit grinding test could there fore be a convenient method for the detection of differences in the grindability of ores.

Jan 1, 1992

By X. Yang, G. D. Zhai

The prop is the most important part to ensure the proper functioning of hydraulic support. When the hydraulic support is impacted by the roof, the prop is prone to extrusion deformation, expansion, and even bursting. In order to study the stress on a doubly-telescopic hydraulic support prop under impact load, an impact simulation was carried out based on the drop weight method. First, the impact model of the hydraulic system of the prop was established in AMESim software and the dynamic response curves of the bottom and middle cylinder of the prop obtained. Then, according to the conservation of energy, the pressure formulaes in the hydraulic cylinder of the prop under impact load were derived and verified by the AMESim simulation results, and the maximum pressure on the inner surface of the hydraulic cylinder of the prop obtained. Lastly, the transient dynamic simulation of a hydraulic support prop was carried out in ANSYS Workbench software, and cloud diagrams of stress and deformation of the prop obtained using Workbench simulation. The AMESim simulation process describes the change in fluid pressure in the prop, and the pressure formulae can be used to estimate the internal pressure of the prop under impact load. The finite element analysis results show that the stress of the middle hydraulic cylinder is much greater than that on the bottom hydraulic cylinder under impact load, which can provide a reference for prop design.

Jul 2, 2022

By M. A. van Nierop

The Discrete Element Method (DEM) is a model that is used to simulate the motion of the media in a grinding mill. The sum of the energy that is lost in inter-media and media-wall collisions represents the power drawn by the mill. The fact that the DEM predicts the power drawn by grinding mills over a large range of diameters has been used to show the validity of the DEM. However, the power drawn by a mill is a function only of the sum of forces of the load on the shell liners. A more accurate and detailed validation of the DEM would be to measure these forces as a function of angular position as the liner moves under the load, and to compare these measurements with predictions generated using the DEM. An experimental mill has been developed to reproduce exactly what the 2-dimensional DEM simulates. The 0,55 m diameter mill has a length of 0,023 m, which is fractionally larger than the diameter of the media used in the mill. One of the lifters in the mill has been instrumented so that the forces on the lifter can be measured as the mill rotates. The DEM simulation will be used to predict these forces. This will give experimental evidence of the validity of the DEM for modelling load behaviour in rotating grinding mills.

Jan 1, 1999

By A. M. Hearn, J. R. Henning, A. S. J. Van Rensburg

The lining, together with the electrodes, forms the heart of the operation of a submerged arc furnace. Subsequent to a lining failure on M12 furnace during the early 1980s, Metalloys was active in investigating the concept of thermally efficient ?freeze? linings for its furnaces. The theory revolved around that, not only would, thermally efficient linings result in significant cost savings, but they would also last longer as a result of being subjected to less harsh operational conditions. After having proved the concept on the .smaller. furnaces, Metalloys decided to implement the concept on its largest submerged arc furnace, M12 Subsequent to having recovered from an impending failure of a lining installed in 1981 in M12 in the mid 1980s, Metalloys managed, through rigid lining management, to extend the life of this lining to 1999. At the end of 1999 the decision to replace the lining in the furnace with a ?freeze? lining was made and planning and design proceeded in earnest. This paper discusses the options considered in making the final decision. The features of the design of the lining are also discussed. Consideration is given to the furnace shell cooling system as a result of its importance in maintaining the thermal equilibrium in the lining. Note is made of the fact that the purchase of a .freeze. lining is an expensive exercise but that the time savings in the installation of the lining and the efficiency improvements during operation far outweigh the additional capital cost. The experience on M12 has been that the payback period of the marginal capital expenditure is less than three years. As a result of the opportunity to reline a furnace the size of M12 not presenting itself very often, the learning points from the installation of the lining and the operational advantages and disadvantages are significant. Finally, the point is made that the project had its pros and cons but overall the success of the project has been evident and, as such, the ?freeze? lining is likely to become the norm at Metalloys.

Jan 1, 2004

By J. Ndlovu, R. Hundermark

Keywords: Anglo Platinum, Polokwane Smelter, pyrometallurgy, metallurgy, platinum, platinum group metals, PGM, base metals, nickel, copper, sulphide smelting, electric furnace, Söderberg, electrode, matte, slag, flash drying, matte casting, crushing, granulation Anglo Platinum?s Polokwane Smelter is situated outside Polokwane, in the Limpopo Province of South Africa. Wet concentrate is received from various concentrators along the Eastern Bushveld Complex, with 60% of the total concentrate received being from UG2 reef and 40% from Merensky reef. The concentrate grade differs from 35 g/t to 110 g/t, and from this a PGM-rich nickel-copper matte is produced. The furnace matte produced is sent to the ACP converter in Rustenburg. The Anglo Platinum concentrators, from which concentrate is received, are Lebowa, Potgietersrus, Amandelbult, and Union, as well as the joint venture Modikwa. The concentrate is fed to two flash dryers that utilise coal-fired, fluidized-bed hot-gas generators to produce the hot gas that will drive off the moisture, leaving a fine bone-dry concentrate to feed to the furnace. The dry concentrate is pneumatically transferred to a storage silo before being transferred to the feed bins situated above the furnace. Lime, if required as a flux, may be transferred separately to the furnace feed bin by a pneumatic system. The concentrate and lime is fed from the feed bins onto airslides and into the furnace. The feed rate is automatically controlled, and the system is set up to optimize the power to feed ratio. The electric furnace is nominally rated at 68 MW and the power is transferred into the furnace using six 1.6 m diameter Söderberg electrodes. Concentrate is melted by energy generated when electric current passes through the electrodes and resistive slag layer. On melting, two immiscible phases form: slag and matte. Furnace matte, containing the bulk of the base metal sulphides and PGMs, is denser than slag and collects naturally at the bottom of the furnace. The furnace is constructed of a combination of refractory brick and water-cooled copper coolers. The furnace sidewalls and hearth are cooled by air drawn through the area by cooling fans. The hearth and matte zone are constructed from refractory bricks. The copper coolers reside only in the slag zone of the furnace along the entire perimeter of the furnace. One staggered row of plate coolers is installed above the waffle coolers along the perimeter of the furnace. Matte is tapped periodically through one of the two matte tapholes into 35-ton refractory-lined ladles, and cast into matte ingots on a casting machine. The cooled matte is discharged onto a concrete slab for cooling and then transferred by front-end loaders to the crushing plant. The matte is first crushed in a jaw crusher and then a Rhodax cone crusher to a size of 2 mm before it is loaded into tankers and sent to the ACP. The low-grade slag is tapped from the furnace through a water-cooled copper insert into a short water-cooled copper ?hot launder? which discharges into a granulation cold launder. The granulated slag slurry flows to three rake classifiers, from which the coarse slag is discharged onto a conveyor to dewatering silos. The dewatered slag from the silos is dumped. The water overflow from the classifiers reports to two thickeners where the water is clarified, and the thickener underflow is returned to the rake classifiers. The smelter is a zero-effluent plant and all the water from the slag silos where the slag is dewatered, as well as the storm water, is pumped to the process water dam from where it is pumped back into the plant for process water use. The off-gas from the furnace is drawn through a forced draught cooler and into a high temperature baghouse. The dust collected in the baghouse is pneumatically transferred into bins above the furnace and is fed via the concentrate airslides. The cleaned off-gas is then vented through the main stack.

Jan 1, 2006

By A. J. Roets

Despite its growth over the years, necessitating ever¬larger office accommodation, the Gold Fields group changed its head office address in Johannesburg only twice in 94 years. The first move was at the turn of the century, from the then select suburb of Doornfontein to the corner of Fox and Simmonds Streets. The second move was in the thirties, from that address-now the Reserve Bank building-to the well-known address of 75 Fox Street. With the advent of the first mines of the West Wits Line by the end of the thirties, 75 Fox Street proved too small, and the eastern section of the Commissioner Street side of the present head office was added on. In the fifties, when space once more became a serious problem, the old Exploration building was purchased and demolished, and the present west wing on Commissioner Street was built on the site. In the early seventies, cramped conditions again made life difficult and, despite a reorganization of the interior layouts, the need for expansion remained critical. Eventually, the adjacent Hollard Place and parking area became available, and plans for an extended new building complex could he considered. The building project was

Jan 1, 1985

By P. Fredriksson, S. Seetharaman

In the ladle refining process, the ?FeO?-content of the ladle slag is of great importance in the chemistry as well as the energetics of the process. An optimization of the process requires an accurate knowledge of the thermodynamic activities of ?FeO? in the ladle slags. Due to the discrepancies in the existing data, renewed attempts are being made at the Royal Institute of Technology to generate reliable data for binary, ternary and multi component slags containing ?FeO? at steelmaking temperatures. In order to measure the activities of ?FeO? in the slags, a gas equilibration technique was employed in the present work. The slags, kept in Pt-crucibles, were equilibrated with a CO-CO2-Ar gas mixture and quenched after equilibration. The chemical composition of the slag was analyszed. From a knowledge of the thermodynamics of Fe-Pt system, the ?FeO? activities in the slag could be evaluated. The results of the present studies, together with other literature values, were optimized in the slag software, THERMOSLAG® developed in the Royal Institute of Technology, Sweden. The results of the optimization are presented. Model calculations were performed with the KTH slag software, THERMOSLAG®, by using plant data from OVAKO Steel, Hofors, Sweden. It was found that oxygen estimations in the metal from the ?FeO? analyses of slags, obtained by conventional sampling and analysis methods, where less reliable. Estimation of the oxygen levels utilizing the sulphur partition between the slag and the metal were carried out using the THERMOSLAG® software. Reasonable estimations of the oxygen contents in the metal confirmed that this could be a very useful tool for the plant operator. Keywords: ladle, thermodynamics, slags, ?FeO?, experimentation, modelling, sulphur partition

Jan 1, 2004

By M. D. G. Salamon

If a transition from one equilibrium state to another occurs during the course of mining, energy transfer takes place in the rock mass, which is assumed to be an elastic continuum. The energy components are defined as follows: the work done by external and body forces, W; the increase in stored energy in the mass, Uc; the strain energy in the rock mined during the transition, Urn; the work done on mine support or backfill, Ws; and the released energy, Wr. The energy balance is defined as (W + Urn) - (Uc + Ws) = Wr> 0, where the first set of components in parentheses represents the sources of energy, while that of the second corresponds to the known modes of energy expenditure and the component on the right is the unaccounted-for energy surplus, which must be released and dissipated in some form. The inequality Wr ~ Urn> 0 applies. Expressions for the energy components are derived first for the general case and then for the 'slit' modal used to simulate tabular excavations. Through specific examples, the importance of the progressive nature of mining is emphasized. The size of the steps used to enlarge the excavations appears to play a significant role in the mode of energy transfer. This observation forms the basis of the second paper in this series of two papers.

Jan 1, 1984

Beatrix Gold Mine, a deep-level gold mine in the Free State province of South Africa, has the highest methane emission rate of any gold mine in the country. Methane is emitted from underground sources intersected during mining operations and is liberated into the general mine atmosphere. The total methane emission rate for the mine is of the order of 16001/s and the South section of the mine emits approximately 10001/s of methane gas. The mine has a history of gas accumulations which have led to a number of underground explosions. Following the last explosion in 2001 and the subsequent investigation, a number of recommendations were made. Two of these were to consider extracting the underground mine methane to render the mine atmosphere safe, and to declare hazardous locations that require special operating procedures. A number of such workplaces have now been declared at the South section of the mine. Methane gas is a potent, explosive greenhouse gas whose contribution to global warming and climate change is 21 times higher than that of carbon dioxide. To reduce its inherent danger and to mitigate its global warming impact, a carbon credit project under the Clean Development Mechanism (CDM) of the Kyoto Protocol has been developed and implemented, the aim being to capture and destroy the methane at Beatrix mine. The mine has constructed an extraction system to capture and extract 400 (Is of the methane. Percentage methane (per volume) of the gas intersected at source is 85%, with negligible concentrations of other hydrocarbons and water associated. The mine contracted the services of Group Five to design and construct the flare and ancillary equipment on surface, and Promethium Carbon was contracted to assist with the carbon¬-related aspects, approval framework, and administration of the project. A number of design and construction challenges had to be faced to extract and transport the gas effectively to the surface of the mine as the emitters are approximately 3 600 m away from the mine shaft at a depth of 860 m. Further considerations were the requirements for the type of column to be used to transport the methane gas, the pressure loss over the system, the safety systems needed to address the risk factors involved in the transport of the methane gas, and a suitable pumping system to extract the gas to the surface. The system operates under negative pressure provided by two blowers on surface delivering the emissions to a flare capable of burning off 450 8/s of methane gas. In this paper a number of benefits for the mine are discussed. These include, but are not limited to, the removal of approximately 55% of the total volume of methane gas from the general body of the air in the geographical areas of the mine where the methane gas is emitted into the atmosphere, and reducing the risk of methane-related incidents. A further benefit of this project is the mitigation of the global warming impact of the methane gas and the reduction of the mine's carbon footprint by approximately 25%. This project could also assist in alleviating the energy shortage being experienced in South Africa by means of the planned generation of 4 MW of electrical power, utilizing the methane gas, as a second phase of the project.

Jan 1, 2011

By R. Hummel

In the quest to reduce overall costs and improve operating efficiency, the application of GPS based technology in open pit mining has evolved significantly in recent times. Venetia Mine has been leading the way in the De Beers group in the implementation of these systems and the realization of significant benefits from them. Following on from the successful results and the notable benefits obtained from the Wenco Truck Dispatching system and the Caterpillar CAES system on the loading and dozing equipment, Venetia has implemented the first fully functional and integrated GPS based drill monitoring system in southern Africa to its drilling operations. This paper elaborates on the concept of drill monitoring and how the vision for the application of the system at Venetia has developed and been implemented. The paper further describes the workflow involved, beginning with the initial test work done with SSI Kaltex and the Australian Drill Advisor system through to the final details of the integration of the Aquila system with the CATERPILLAR Computer Aided Earthmoving System (CAES) and the alliance with SandvikRock Tools. Most importantly, the paper details the benefits that are derived from drill monitoring and the use of the information generated by such a system. Venetia has pioneered the move towards smart partnerships and alliances with strategic suppliers within the De Beers group. The area of drilling, as the important start of the entire mining process, has been no exception and the final part of the paper covers how drill monitoring provides vitally important information that enables a supply partnership, to function cost-effectively and profitably for both parties involved. By having the type of accuracy, detail, validity and timeousness in the information being received as a result of the implementation of such a system, better management decisions can betaken, creating a more focused and efficient mining environment. In these times of increasing costs and reduced commodity prices, the mining industry will be required to continue pushing the boundaries on these technology applications in order to remain competitive.

Sep 1, 2001