Search Documents

By Baruch Grinbaum, Edwin Bwalya, Robert Minango, Deogratias Bukunkwe

Solvent extraction of Cu from acidic leach, using an oxime extractant, e.g. LIX 984 or Acorga is a well known and established process. As the process advances, Cu is extracted to the solvent and is replaced by H+ in the aqueous phase. At high acidity the distribution coefficient of Cu between the solvent and the aqueous phase decreases, and eventually relatively high concentration of Cu remains in the raffinate, regardless of the number of equilibrium stages. In many processes this phenomenon is immaterial, as the raffinate returns to the leaching and no copper is lost. But when the copper raffinate is used for processing of additional metals, minimal concentration of Cu in the raffinate is essential for an effective process. The recommended process includes three steps: 1. SX-1: Standard extraction of Cu with oxime. The resulting raffinate contains about 6-8 g/L Cu and 50 g/L H2SO4. 2. SX-N: Extraction of most of the acid into an amine-based solvent, and stripping it with a base, e.g. aqueous ammonia, caustic, Na2CO3 etc. The extraction removes no metals, but decreases the concentration of acid from 50 to 10 g/L. 3. SX-2: Extraction of the neutralized solution once more with oxime, to remove the residual copper. Such a process enables one to get down to 100-150 ppm Cu in the final raffinate. This process was developed and tested in the R&D facility in Chambishi Metals plc, by a joint team of Chambishi & Bateman, using Cognis LIX 984N and real solutions from the plant. In the laboratory scale, the equilibrium isotherms for SX-1, SX-2 and the neutralization were developed. Computer simulation of the results showed that the optimal configuration is two stages for both extraction and stripping for SX-1. For SX-2 2-3 stages of extraction and two stages of stripping are needed. The stripping stages may be common to both SX-1 and SX-2. The neutralization of SX1 raffinate was tested both by conventional precipitation with lime and by extraction with Alamine based solvent extraction and stripping with a solution of 10% NaOH. For the SX-N only one stage was needed for both the extraction and stripping. The bench scale pilot plant was run for both SX-1 & SX-2. The results were very similar to the simulated ones, and the configuration of 2E2S for SX-1 and 3E=2S for SX-2 delivered the required raffinate with less than 150 ppm Cu.

Jan 1, 2005

The Gordonsville Operation of Pasminco US Inc. along with the Center for Advanced Mineral and Metallurgical Processing (CAMP) at Montana Tech studied, developed and implemented a pilot-scale hydrometallurgical facility for the industrial recovery of germanium and gallium. This paper describes the joint testing and engineering programme that culminated in this successful process.

Jan 1, 2008

By P G. Gaylard

The minerals Industry carries out over US$ 2 billion of R&D annually. The R&D is performed at three levels ? in house research facilities; on a one-on-one basis with a research provider; as syndicated (collaborative) research. The key to a successful R&D programme is project selection. It is suggested that at this time of ?bounty? for the minerals industry the research portfolio should contain some ?blue sky? but potentially long term significantly beneficial projects. This said, the projects should align the technical concepts with the business imperatives. AMIRA has found the ?Road Map? concept has assisted in defining areas for R&D. Examples of this methodology using a Copper Road Map developed by AMIRA for the copper producers operating in South America is presented. The benefits derived from syndicated research are also discussed.

Jan 1, 2007

By M. A. Kujoana

Following on the design of good mining layouts and regional support systems, and the implementation of sound strata control practices, stope support is the ultimate strategy to combat the hazards of rockfalls and rockbursts. The primary function of stope support in intermediate and deep level mines is to stabilize the rock mass immediately surrounding stoping excavations, that is, the zone of fractured rock which behaves in elastically around stopes. Support design is a process resulting in a support system which is both practical and meets or exceeds by a factor of safety the requirements for a particular geotechnical environment. The aim of this project was to design a support system, which accommodates the factors of rockfalls and rockbursts. The pack support unit must be easily handled, less costly and can be used in stopes without any significant convergence. The project tested the structural stability of packs to their expected deformation, in order to design a height to width ratio for stopes where little convergence is expected.

Jan 1, 2009

By F. Crundwell, A. J. Lathwood

A number of base-metal operations would like to increase production to take advantage of the higher metals prices. In general, this higher production should not be achieved with major operating changes. In hydrometallurgical facilities, leaching and pressure leaching represents one area where upfront limitations may be a bottleneck to the capacity of the entire plant. An assessment of the capacity of the leaching tanks and autoclaves was performed using a predictive model within the AweSym flowsheet simulator. The model is described, and the results of the application of the model to a number of different leaching reactors are presented. It is argued that the leaching number, which relates the residence time, particle size and the leaching rate, is of prime importance. Finally it is shown that there are some unexpected catastrophic events in increasing production capacity without a thorough understanding of the leaching operation.

Jan 1, 2007

"Chairman: Professor H. S. SICHEL Rapporteur: Miss M. I. WATSONPapers:Unrolling of Copperbelt orebodies by J. H. E. Perry and V. H. WiikAn exploration model for tabular orebodies by G. S. Koch and R. F. LinkHarmonic analysis of copper and gold occurrences in the Arbitibi area of the Canadian Shield by F. P. Agterberg and A. G. FabbriMathematical models of orebodies by M. J. Newton and A. G. Royle Estimation of lateritic-type orebodies by A. JournelIn his presentation Mr Wiik said that unrolling could be regarded as a reversal of the natural process of folding, so that the aim of an unrolling procedure would be the reconstruction of original pre-tectonic conditions. While simply formulated, this aim might not always be achieved. The geometrical relationship between points on the deformed surface and corresponding points on the original surface is process-dependent, and a true reconstruction could be achieved only if the deformation history were known in detail.In this computer unrolling procedure all these complexities were ignored. Referring to one particular marker horizon, Mr Wiik said that it was assumed in the procedure that this marker was deposited as a horizontal stratum and that it had subsequently been deformed by simple flexure-type folding.The procedure allowed the geologist to incorporate his knowledge and conception of the deposit through repeated re-contouring with dummy points. This 'manumatic' aspect of the procedure had proved invaluable, not only in resolving specific unrolling problems but also in making the system more acceptable to the geologists in general.Unrolling served towards removing what might be termed `tectonic noise' superimposed on the primary distribution patterns for regionalized variables such as metal content and orebody thickness. From this point of view, variograms derived on the basis of unrolled-plan co-ordinates should be more meaningful in terms of depositional environment than are variograms calculated from a normal map projection.Mr M. M. Oosterveld remarked that it appeared from the paper that there were problems in applying the unrolling technique to ore reserve calculation, and asked whether there were not other methods that might be used for that purpose.Mr Wiik replied that at present unrolling played only a minor role in practical ore reserve estimation within Roan Consolidated Mines, Limited. The techniques currently in use differed from one orebody to another, but in general they involved projection onto a vertical longitudinal section or a horizontal plan, with subsequent grid interpolation by means of a standard computer contouring package."

Jan 1, 2014

By G. B. Dukes

Scaling of rockpasses was problematic at Tau Lekoa Mine prior to production commencing in 1991. High horizontal stress levels relative to the host rock mass strength have been instrumental in causing the observed scaling. Scaling has been more pronounced in the deeper rockpasses and these are monitored regularly. Rehabilitation of one of the reef passes and one of the waste passes was required in the period 1999 to 2001. This paper describes the extent of the problems experienced to date as well as the rehabilitation completed.

Jan 1, 2006

By J. A. L. Napier

SYNOPSIS Many tabular mining problems can be modelled effectively by displacement-discontinuity techniques, which can be extended directly to represent fracturing on discrete planes and movements on planes of weakness. This paper presents a unified method for computing the energy changes that occur when multiple discontinuities intersect and are extended incrementally. It shows how this method can be used to deduce energy-release information for standard layout problems and, in addition, how the technique can be incorporated in numerical procedures based on the displacement-discontinuity method. Examples are given to demonstrate the effects of off-reef fracturing and the importance of stope-fault intersections during seismic events.

Jan 1, 1991

By I. McDougall

The matte/slag tidal zone in a nickel-copper-iron-sulphide matte smelting furnace is subject to severe process conditions that can lead to premature failure of the lining. The MgO-FeO-SiO2 slag is aggressive to refractory bricks, while the Ni-Cu-Fe-S matte is aggressive to water-cooled copper cooling elements, and can penetrate and sulphidize refractory bricks. A novel approach to the lining design was taken at a PGM smelting furnace, where an indirectly-cooled graphite ring was applied in the matte/slag tidal zone, with refractory bricks on the hot face. The graphite was cooled by the copper cooling elements in the slag zone, obviating the need for copper cooling elements in the tidal zone. In this paper the effectiveness of different lining designs utilizing varying degrees of cooling in the slag zone and slag/matte tidal zones is compared. In comparison to water-cooled copper in various configurations, cooled graphite shows promise as an indirect refractory cooling system in the tidal zone area of furnaces. Keywords PGM smelting, graphite, refractory lining, copper cooling elements, submerged arc furnace.

Aug 1, 2013

By B. Das

he flotation studies on hematite were carried out using di (2-ethylhexyl) Phosphoric acid (D2EHPA) as the collector. The possible mineral reagent interaction was studied through electrokinetic and dissolution studies. The shift in zeta potential (PZC) and decrease in dissolution of iron in the presence of D2EHPA indicated that D2EHPA was specifically adsorbed on hematite surface. The adsorption imparted necessary hydrophobicity for flotation of hematite. Hematite could be floated selectively from hematite and quartz synthetic mixture. Key words: Hematite, D2EHPA, flotation, electrokinetics, dissolution.

Jan 1, 2003

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The stability of a ferrosilicon dense medium suspension is one of the most important parameters to keep under control since it determines the density gradient of the medium in the separation zone and thus directly influences separation sharpness. The stability of ferrosilicon suspensions were characterized using settling tests employing a differential pressure method. Particles smaller than 45 µm and especially the ore fines played an important role in the settling behaviour of the solids. High medium stability is favoured by ore fines, fine medium particles, and high medium densities. Keywords: dense media, ferrosilicon, dense medium stability, ore fines

Jan 1, 2002

By H. C. Van Der Merwe

In the 21st century, dynamic, accurate digital 3-D geological models are essential to the pursuit of safe, efficient and profitable mining. This is particularly true for the deep-level underground mines in South Africa. The Sirovision® solution is a collaboration project between the Australian CSIRO (Commonwealth Scientific and Industrial Research Organisation), Datamine Software Ltd. and AngloGold Ashanti Ltd (AGA). The purpose of the project is to provide a fully integrated digital rock face imaging, geological mapping and modelling system for the AGA gold mining operations. The CSIRO-developed Sirovision® Stereo Camera Rig (SCR) consists of two digital cameras, alighting system, a laser guidance system and image processing software. The imaging system works on the principles of photogrammetry, i.e. overlaying of two 2-D images with a central focus point, with mathematical algorithms extracting 3-D information from the 2-D image pair. The output from matching several image pairs is a computer-generated, full 3-D, virtual copy of the mining excavation. The image resolution and relief ares of sufficient quality to distinguish different rock types and structural contacts. Functionality within Datamine Studio3 is used to add geological intelligence to the 3-D images provided by Sirovision®. The geologist identifies and ?draws? lines representing geological features directly onto the image. By utilizing the inherent ?topography? of the 3-D image, the software is able to convert the lines into 3-D surfaces, ready for use in the 3-D geological model. Subsequent to promising underground test results from AGA?s Sunrise Dam Gold Mine (SDGM) in Australia and other mining operations worldwide, it was decided to test the Sirovision® system in the South African deep-level gold mines. The first underground tests at Moab Khotsong Mine began in January 2009. The objectives of these tests entailed the capturing of 3-D images of selected development ends, mapping of geological features onto the 3-D images and integration of the mapping data with the 3-D geological model. Some downsides have cropped up during the feasibility testing, related to practicality of the SCR for acquisition of 3-Dimagery in the deep-level underground operating environment. These constraints will have to be addressed prior to operational implementation. Facing such difficulties is not unusual when attempting to implement new technology in such a challenging working environment and testwork is still in progress at the mine in order to prove the concept of using this technology in a Witwatersrand underground gold mine. The great advantage of the Sirovision® solution is that it offers the geologist the opportunity to work remotely on a 3-D virtual copy of a mining excavation, without the heat, humidity, hazards and time constraints associated with physical mapping in an underground workplace.

Jan 1, 2009

By V. E. Ross

A computer program was developed that incorporates a novel analysis of the behaviour of the froth in full-scale cells to predict the performance of the froth over a wide range of operating conditions. The program has the distinct advantage that it can be easily implemented on a microcomputer, which allows rapid computation and processing of the results. The program utilizes experimental data obtained in flotation-plant and laboratory testwork to provide parameters for the froth model under an initial set of operating conditions. These parameters can then be used in conjunction with a model describing the transfer of material from the pulp to the froth to predict the performance of the cell when its dimensions and operating variables are changed during scale-up.

Jan 1, 1987

By D. van Heerden

In the mining industry abrasion caused by both sliding and impact have over the years resulted in costly damage to installations such as ore passes and silos. Good geotechnical practices combined with the use of a high quality abrasion resistant concrete can prolong the life of such an installation and minimize problems associated with abrasion. In order to maximize the life of an abrasion resistant concrete, the choice and combination of the correct raw materials (cement, aggregate and fibre) and overall mix design needed to make up such a concrete are important. This paper presents technical data and practical experience showing that concrete formulated with calcium aluminate cement resists severe abrasion conditions better than similar OPC-based concretes.

Jan 1, 2005

By D. J. Adams, R. G. Gürtunca

In situ measurements and numerical modeling based on elastic theory showed that backfill stresses are considerably higher than originally thought. This has led to a change in understanding of rockmass behaviour. After describing previous work on the behaviour of the rockmass, this paper discusses possible reasons for the high stresses measured in backfil, and identifies the rockmass mechanisms possibly generating these stresses. It is concluded that the joints and the geological stratigraphy can lead to increased elastic convergence, and that the inelastic behaviour of the rockmass is also partly responsible for the increased closure measured in backfill. The use of an in situ modulus is suggested as an interim solution until a new computer model that allows for joints, different layers, and inelastic closures becomes available.

Jan 1, 1991

By B. Elevli

This paper deals with the selection of alternative accesses to a podiform chromite orebody in Turkey. The most important alternatives studied in a related project have been stated as a new vertical shaft and a ramp system. The comparison of these alternatives have been carried out on the basis of total investment costs, ore transport unit cost and net present value (NPV) of overall project for various depth. The results show that up to the depth of 700 m, the total investment cost and NPV favours the ramp access while unit ore transport cost make the shaft access preferable.

Jan 1, 2002

By R. F. Taberer

Within the technology field generally known as biological heap leaching or percolation leaching, lies a wealth of technological knowhow that is potentially patentable and therefore can form the subject matter of patent applications. An organization often overlooks the potential for generating intellectual capital during its research by dismissing the possibility that what it is working on may be novel and inventive and therefore patentable. The organization labours under the misconception that there is nothing patentable in its work mainly because the novel aspect is overlooked against the general background state of the art or, if identified, is not recognized as having sufficient inventive merit. In the field of biological heap leaching, patents have issued on inventions that extend across a large range of technology, including microbiological inventions-for example a particular strain of microbe used in a heap leach application, electro-mechanical inventions, for example a column simulator that simulates the heap leach environment, and thermodynamic inventions such as methods of generating and maintaining heat in a heap.

Jan 1, 2012

By D. Bessinger, H. Kotzé, J. Beukes

Keywords: Pyrometallurgy, furnace, ilmenite, smelting, Ticor Ticor SA began with a detailed feasibility study in 1995. The Hillendale mine (situated between Richards Bay and Empangeni) and Mineral Separation Plant were approved in 2000. The smelter, just outside Empangeni, consists of two 36 MW DC arc furnaces that were commissioned in 2003. Experiences gained during the initial commissioning of the furnaces proved valuable in later commissioning work, as shown by the increase in ramp-up rates. The capacity of the plant is 250 kt/a TiO2 slag and 145 kt/a of pig iron.

Jan 1, 2006

Guide Io Ihe Preparailon Of Papers For Publication In The Journal Of The South African Institute Of Mining And Metallurgy The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by the Council.

Jan 1, 1975

By C. Lemmer

The resolution with which the different categories of resources are forecast for Witwatersrand gold reefs should ideally tie in with block sizes that are optimal in terms of the variability structures of the reefs. A tool, called the ?variancegram?, is proposed as a basis for block size choice. A variancegram is intrinsic to the particular reef and mine concerned. A further requirement is the ability to attach global confidence limits to weighted average estimates built up from combinations of local kriged estimates. Approximations to derive global kriging variances based on variables derived from local kriging deliver hugely inflated results if ordinary kriging is used, and markedly better, but not accurate, values if simple kriging is used. These approximations improve as the number of samples used in kriging each block is increased. It is shown that the behaviour of the different components of the global kriging variance with increasing number of samples, all differs, but they all link to the variancegram for the particular reef. The variancegram can thus be used to correct the different components to the values they would have had if all samples were used in kriging each block, and so deliver the ?correct? global kriging variance, even though only a limited number of samples were used in kriging each block. The desirability of having very stable solutions implemented in production systems is taken into account in the proposals. It is anticipated that the same variancegram findings will also hold for other densely sampled deposits, but this remains to be investigated.

Jan 1, 2014