Search Documents

By D. M. MacHunter, M. K. Palmer

Refinement of design parameters and features has resulted in the development and commercialization of spiral separator models that offer enhanced performance for a number of application areas. Examples of recently developed spiral separator models include the enhanced performance (EP)spiral and the HC (high capacity) series. Comparative performance data for appropriate applications are presented for each of these new model spiral separators. The utilization of spiral separators providing improved performance offers significant cost and operational benefits for process plants. Examples of process flowsheet changes that have resulted from the incorporation of recently developed spiral separators include the reduction of the number of process stages and the achievement of high density tailings by the utilization of a dewatering arrangement in the spiral tailings splitter system.

Jan 1, 2003

By Pierre Marcotte

Jackleg rock drills expose their operators to high hand-arm vibration levels. To address this problem, an antivibration handle has been developed. The antivibration properties of the handle were achieved through a suspension based on a hinge design, achieved with a torsion spring and o-rings. To provide some bench marking for this new handle and to follow the evolution of its performance over time, a test bench was developed to characterize the vibration emission values of jackleg drills under controlled operating conditions. Testing of four antivibration handles on the test bench have shown reductions of the overall weighted acceleration level in the order of 54 % to 60 %, with most of the attenuation occurring in the zh-axis at the rock drill percussion frequency.

Jan 1, 2008

Mr K.C. Owen started his mining career as a learner official after matriculating at the Parktown Boys' High School, Johannesburg in 1967.

Jan 1, 1991

By W. P. Nel

The introduction of the Higher Education Qualifications Framework (HEQF) and the updated Higher Education Qualifications Sub-Framework (HEQSF) has caused many South African university departments to rethink their programme qualification mixes (PQMs). In addition to the requirements stated in the HEQSF, a number of other factors have to be taken into consideration by a university department. These factors include, for example, the standards generated by the Engineering Standards Generating Body (ESGB) and subsequently approved by the Engineering Council of SA (ECSA) and the need to prepare students for various categories of professional registration with ECSA. This means that a university department has to choose the correct mix of Learning Programmes (LPs) from the HEQSF menu (which consists of 13 types of LPs). Preparing students for ECSA registration is aligned with the mission of universities, which is to teach and undertake research. However, research and the LPs associated with research go beyond the requirements for current ECSA registration. Assuming that universities offering engineering LPs would elect to prepare students for both ECSA registration and teach them to produce research outputs, which is mostly done at Master and Doctorate levels (NQF Levels 9 and 10), then it follows that academics are more interested in NQF Level 5 to 10 pathways (abbreviated as ?L5-10?) rather than the shorter pathways required towards professional registration. (For example, ECSA requires an NQF L5-L7 pathway for registration as a candidate professional technologist. This specific pathway may consist, for example, of two LPs, namely the 360-credit Diploma and the Advanced Diploma.) A L5-L10 pathway is a combination of LPs that will prepare the learner with a NSC (or equivalent qualification at level 4) to Doctoral level (level 10). Universities may choose at least four major pathways from the HEQSF menu in order to educate and develop students from NQF Level 5 to 10. However, various pathways towards registration in the category of candidate with ECSA are also embedded into these four NQF L5-L10 pathways, where each consist of a unique combination of LPs. Each of these pathways has an opportunity cost, and economic reality means that smaller departments may have to choose between the four pathways. Of all the many factors involved in PQM decision-making, the focus of this paper is on the HEQSF requirements, ECSA standards, and ECSA registration and how these, together with the various qualifications and educational LPs provided for by the HEQSF may impact on the PQM decision taken by engineering departments and schools at South African universities. The proposed four NQF L5-L10 ?pathway tool? for PQM decision-making may be useful for pointing out the advantages, disadvantages, and applications of the various pathways and combinations of pathways. Rather than deciding from a menu of thirteen qualifications and associated LPs, this article proposes that decision-making be undertaken on the basis of a menu of four main articulated ?NQF L5-L10? pathways (which also include one or more of the ECSA?s pathways for professional registration). The proposed ?NQF L5-L10 pathway? tool is an attempt to move one step closer to the aim of achieving a structured decision-making approach for designing a PQM at departmental level.

Jan 1, 2014

By J. Zhang, A. J. S. Spearing, L. Ma

Ore deposits are becoming more complex to mine as a result of the exhaustion of surface and other easily mined deposits. There is also increasing socio-political pressure to design more environmentally sound, sustainable, and safe mining practices. Wang and Ma designed a mining method for coal, similar to a modified drift and fill using a continuous miner to take sequential cuts (rooms) that are subsequently backfilled. The authors have modified the concept to make it more autonomous, safer, and less costly using highwall coal mining techniques, modified and adapted for underground applications. The method is more flexible than longwall mining and the percentage extraction would seem to be in the same range. In addition because of the backfilling, surface subsidence would not be a major issue and could be more effectively managed.

Feb 2, 2021

By M. Weir, J. R. Cutland, L A. J. Pronk van Hoogeveen

"A computer system for the design of open pits to mine stratiform orebodies has been developed for use at Nchanga Consolidated Copper Mines, Ltd. The particular requirements of such a system, for example, the accuracy of representation of geological detail and the ability to follow footwalls, arc described in this paper, together with the methods that have been adopted to satisfy them.A modified version of the Open Pit Design Program of Rio Tinto Zinc Consultants, Ltd. is incorporated in the system and the geological data are converted into a form usable by the computer by means of a pencil follower. Some of the uses which have been made of the system are described, with reference to the long- and medium-term planning of the Nchanga Open Pit, the major producing pit at Chingola Division."

Jan 1, 2014

By B. G. Fordyce, W. B. Parker

A description is given of the methods used in management planning, pit-equipment selection and maintenance operator training, and formal organization of mining personnel.

Jan 1, 1979

By Kurt R. P Petersen

This paper discusses the current approaches to modelling the DMS cyclone within the De Beers group. Current efforts are split into short term value-adding process understanding and longer term semi-fundamental analysis of separation mechanisms. To date, the basic applied approach has yielded significant value to the group, enabling operators to focus on simple diagnostic measures to control their process. The more involved modelling approach has given rise to a new understanding of the separation field, in particular that the high density gradients within a cyclone are highly localised, indicating that separation of medium to heavy density material takes place low in the cone. The model has proven to be conceptually robust, but still requires further development and validation to become a complete modelling and simulation tool for De Beers.

Jan 1, 2006

This paper describes a simple finite element (FE) modelling approach which leads to the computation of seismic energy release rate (ERR) and strain energy storage rate (ESR) which result from mining. The concept of critical strain energy is introduced as a means to help evaluate the strainburst potential in mine structures. A new, energy-based, burst potential index (BPI) is proposed. The use of ERR, ESR and BPI is demonstrated by a cut-and-fill stope case study. The merits of using such energy parameters in the interpretation and analysis of strainburst phenomena are discussed. While the study gives promising results, site-specific back analyses would be required to first calibrate the model and fit it with the local mine conditions, before it can be adopted as a routine design tool.

Jan 1, 1999

By L. S. Linda, P. G. H Pistorius

Ferritic stainless steel is utilized to fabricate automotive exhaust systems using a ferritic weld metal. Ductility of the weld metal is higher if its microstructure contains a significant proportion of equiaxed grains. The formation of equiaxed (rather than columnar) grains is favoured by a higher titanium weld metal content. In this study, the Ti content of ferritic stainless steel weld metal was changed by using Tifree (Type 436) and Ti-containing (441) ferritic stainless steel as base metals. The metal-cored welding consumable contained 0.4% Ti. Gas–tungsten arc welding and gas–metal arc welding processes were compared. The weld metal Ti content ranged from zero to 0.5% Ti, as determined from scanning electron microscopy supplemented by inductively coupled plasma optical emission spectroscopy. Cross-sections of the weld beads were subjected to point counting (to estimate the fraction of equiaxed grains) and image analysis (to estimate the average grain size). Point counting proved to be more reliable. The fraction of equiaxed grains was sensitive to the Ti content, but not to the welding process. Below 0.4% Ti, the fraction of equiaxed grains gradually increased with an increase in the weld metal Ti content; above 0.4% Ti, the fraction of equiaxed grains rapidly increased with increasing Ti content. The transition in behaviour at 0.4% Ti corresponded to a Ti content at which Ti-rich precipitates became stable at the estimated liquidus temperature of the weld metal.

Jul 2, 2022

The results of a series of physical model studies of the stability of jointed rock slopes carried out some years ago are described. These models were tested under centrifugal loading. Four ?geological? structures were tested; all had the same joint orientations and strengths, but the relative spacing of the joints was different. The results showed that the mechanisms of failure of the slopes varied for the different models, and the gravitational loads at which failure developed also varied. The following conclusions are drawn from the results of the physical model tests: ?the mechanism of slope failure is by progressive deformations throughout the slope ?the ratio of the spacings between the different sets of discontinuities exerts considerable influence on the slope failure ?in the models tested, the intact material strength had no noticeable influence on the stability of the jointed rock slopes(note that for hard rock, similitude conditions indicate a prototype slope height of 300 to 400 m, and therefore intact rock failure might not be expected under simple gravity conditions, i.e. no tectonic stresses) ?rock slope failures are three-dimensional and in general are not amenable to two-dimensional simplification ?knowledge of the orientations of discontinuities in the slopes does not allow prediction of a unique failure surface, nor of a volume of failure. The volume of failure is determined to a large extent by the plan configuration of the slope.

Jan 1, 2006

By C. Haberfield, J. Szymakowski

Recent studies by the authors into the behaviour of jointed rock masses using direct shear testing have confirmed that joint spacing has a significant effect on rock mass strength. The rock mass failure envelopes assessed from these tests have been compared to failure envelopes obtained using the Hoek-Brown GSI criterion. Good agreement between measured and estimated GSI strength envelopes where obtained when joint spacing was considered in the assessment of GSI. Les études récentes conduites par les auteurs sur le comportement des joints rocheux employant l'essai direct de cisaillement ont confirmé que l'espacement a un effet significatif sur la force de la masse rocheuse. Les enveloppes de ruptures obtenues pour ces essais ont été comparées à l'enveloppe de rupture obtenue en utilisant le critère GSI Hoek-Brown. Une bonne corrélation a été constatée entre les enveloppes obtenues expérimentalement et les enveloppes calculées par la méthode GSI quand l'espacement des joints a été pris en considération dans l'évaluation de GSI. Kuerzliche Untersuchungen der Autoren betreffs Reaktionen von gebrochenen Felsmassen zu direkter Scherkraft, bestaetigen, dass die Abstaende von Rissen einen deutlichen Einfluss auf den Widerstand der Felsmassen hat. Die Bruchbereiche der Felsmassen die von diesen Untersuchungen entwickelt wurden, wurden verglichen mit den Bruchbereichen, die man mit der Anwendund der Hoek-Brown GSI Formulierung erhaelt. Eine gute Uebereinstimmung zwischen gemessenen und errechneten GSI Festigkeitsbereichen wurde erzielt, wenn der Abstand der Risse in der Berechnung der GSI in Betracht gezogen wurde.

Jan 1, 2003

By C. Nexhip, S. Sun

Critical to understanding and controlling phase mixing and separation in metallurgical processes, is the development of reliable experimental techniques to measure interfacial properties of melt systems. A series of experiments has been carried out to determine the effect of oxygen potential on the surface tension of liquid copper. Using an electromagnetic levitation method, a surface tension-oxygen chemical potential adsorption isotherm was produced for the Cu-O system at T 1400 K. The surface tension results show good agreement with the literature values e.g. within 3 per cent for pure copper. The Belton `ideal' adsorption isotherm was applied, and the following equation derived to best fit the experimental data ? =1251-77.5 1n41+ (2.79x105 . pO1/2)](mN.m Using this equation, the surface tension of copper was calculated/predicted as a function of oxygen potential at 1400 K, and showed excellent agreement with the experimental values. This confirmed that the adsorption behaviour of oxygen in liquid copper is ideal. The saturation coverage of oxygen on the surface of liquid copper was determined to be T0 = 6.65 µmoles.m,-2 corresponding to an area per adsorbed oxygen atom of ao ? 25 Å2. These values agree well with those cited in the literature, and our experimental data cover a very wide range of oxygen potential (10-5 to 10-17 atm). Keywords: levitation melting, surface tension, Cu-O alloys, oxygen potential, adsorption isotherm, surface coverage.

Jan 1, 2004

By S. Matsuyama, S. Tomita, H. Kawahara, G. Deguchi

A proper management system of coal mine methane gas associated with underground mining activities is essential for the mine safety due to its nature of explosion. Optimum design of the mine ventilation and gas drainage need accurate prediction of gas flow rate emitted by mining activities. Permeability to gas, which is affected by stress conditions of surrounding rock mass, governs the emission rate of the gases. JCOAL has developed a three dimensional FEM simulation program named Mine Gas Flow 3D (MGF-3D). MGF-3D is designed to predict the volume of methane gas emitted from surrounding coal and rock seams based on stress distribution and permeability change which are determined by 3D stress analysis. In MGF-3D, stress change and/or expansion of fractured zone affected by mining is calculated at the first and then gas emission into roadways and longwall panels under the determined stress conditions is calculated using Darcy’s law. MGF-3D also can set up a number of pre-drainage holes and estimate drainage gas volume from each hole. This function makes MGF-3D remarkable program. These simulations for gas emission can contribute to mine gas utilization plan. Comparison between actual measurement of gas emission in the underground mine and simulation results has been performed and availability for the mine safety and problems with MGF-3D are discussed in this report.

Jan 1, 2003

By R Kroukamp

Horizontal belt filters are typically used for separation of relatively free filtering solids where good post treatment is required. He horizontal belt filter is a continuous filter with an endless cloth supported on a grooved carrier belt. The belt and cloth are driven around two rollers across a series of evacuated suction boxes. The feed suspension is introduced at one end of the filter and deliquored to produce a cake at the other end. The benefits of using horizontal belt filters are good cake washing, continuous and visible processing, fully automatic operation, flexibility, high capacity and relative high speeds of operation. If required, horizontal belt filters enable efficient counter-current washings to minimize the usage of wash liquid. The horizontal belt filter has applications in the following: [? Metal concentrates ? Mineral sands ? Tailings ? Coal ? Iron ore ? Alumina ? Chloride processing ? Nickel and Cobalt refining ? Platinum group metals ? Zinc processing ? Many other applications in the Mining and Metallurgy industries ] 2. Operating Principle of a Horizontal Vacuum Belt Filter 2.1 Cake Forming The slurry to be dewatered is evenly distributed onto the filtering surface. Gravity assists the cake formation and the feed can be introduced in multiple stages. 2.2 Cake Washing Once the cake is formed, wash liquor/water can be introduced onto the top of the cake via a wash launder or sprays. Multiple wash stages, co-current, counter-current or direct washing can be added by increasing the length of the filter.

Jan 1, 2007

By P. L. Duncanson, J. D. Toth

Since 1995, when "freeze lining" refractory systems were introduced to the ferroalloy industry, they have gained in popularity, due to the freeze lining?s reputation for reliability, safety, and the contribution it makes to profitability. As with many popular and effective technologies, however, the freeze lining has spawned low-cost pretenders that claim the "freeze lining" name. On the surface they appear to contain some of the components of the technology, such as thermally conductive materials, but they fail to incorporate all of the principles that define a true Freeze Lining. The term "freeze lining" refers to the refractory system?s ability to maintain a temperature profile that is low enough to freeze a layer of process material on its hot face, which insulates the refractory and prevents direct contact with molten metal and slag. In doing so, the common wear mechanisms found in the submerged arc furnace - chemical attack, erosion, and thermal stress - can be prevented. These wear mechanisms are all related to high temperature; thus, they are prevented by maintaining low temperatures. Certain refractory properties and design concepts are absolutely necessary for the lining system to function as a true Freeze Lining. The paper explains these requirements and why they are important - the Truth of freeze linings - and further explains why systems that ignore one or more of these requirements cannot claim to be freeze linings, thereby exposing the Myths.

Jan 1, 2004

By D. G. Hulbert, D. J. Oosthuizen, D. de V. van der Spuy

Expert Online, as a software system, is aimed at providing plant operators in the minerals industry with effective training and on-the-job assistance. It incorporates a number of features to achieve this goal, of which the most important is its ability to explain the dynamics of the plant and control system in simple language, mimicking an informed plant expert who has online access to the inner workings of the plant and control system. This is made possible by a novel form of Artificial Intelligence, called the Interpreting Expert System. Previous implementations of the IES were only capable of explaining controller actions. Expert Online will extend this capability to also perform the more difficult task of explaining process behaviour. Expert Online will implement three main processes, namely the accumulation of data from the controllers and plant models, the interpretation, processing and filtering of that data and lastly communicating the relevant information to the user, both as written messages and in other audio-visual forms. Although Expert Online is aimed at the operator, other plant personnel, like supervisors and plant managers, will also benefit from it. This paper focuses on the structural and functional design of Expert Online for implementation on the latest version of Mintek’s open control platform, PlantStar, highlighting advances and additions since the previous implementations of the Interpreting Expert System and concluding with an example illustrating some of the principles.

Jan 1, 2003

This symposium, being held at The President Hotel, Johannesburg on 9th-11th September, 1969, is being jointly sponsored by The South African Institute of Mining and Metallurgy, The South African Corrosion Council and the Southern Africa Stainless Steel Development Association, and supported by the C.S.I.R. The three days of technical sessions, at which 350 delegates are expected, will include introductory films on the properties and uses of stainless steels, papers on corrosion problems and prevention, design and economics, welding and applications in industries of particular importance to South Africa. The programme includes four overseas guest speakers who are acknowledged leaders in their respective fields. Detailed programmes together with application forms for registration will be published shortly. Enquiries to P.G. Box 8954, Johannesburg.

Members are advised that the Council has decided to change the format of the Journal from the present size to the standard international A4 size with effect from August, 1969. By making this change we will be conforming to more general practice today in regard to publications and this should effect certain economies and facilitate selling of advertising space. It has been arranged that in future the publication of the Journal, including advertisement sales, will be handled by Kelvin Publications (Pty.) Ltd. who are already doing this work satisfactorily for the Mechanical and Electrical Institutes. While making these changes, the opportunity is taken of redesigning the outer cover of the Journal to incorporate the new coat of arms. The Council trusts that these changes will meet with the approval of members.

Book Reviews Linari-Linholm, A. A. Occurrence, mining and recovery of diamonds.Diamond Promotion Services (P.O. Box 62349, Marshalltown, Transvaal). 1974. Rl,OO. Metal Statistics 1962-1972. Metallgesellschaft Aktiengesellschaft. 60th Edition. Frankfurt am Main 1973. 328 pages. Published by Metallgesellschaft A.G., 6000 Frankfurt am Main, Reuterweg 14, Post Box 3724, Western Germany. Symposium on underground mining equipment maintenance~1973. Institution of Mining Engineers, and Association of Mining Electrical and Mechanical Engineers. Colloquium and general meeting A General Meeting and Colloquium on 'Motivation and productivity in the mining industry' was held on May 22nd, 1974, at Kelvin House, Johannesburg. Mr P. W. J. van Rensburg (President) was in the chair. The Colloquium was attended by 170 delegates and was opened by the President at 09h25. Minutes

Jan 8, 1974