Search Documents

By N. Mulaudzi

The use of SO2/air gas mixtures as an oxidant to precipitate Mn from Co(II) leach liquors was investigated. The effects of SO2/air ratio, pH and temperature on Mn precipitation were evaluated. It was found that the use of SO2/air gas mixtures resulted in significantly higher Mn precipitation kinetics compared to using air or pure O2 alone. The SO2/air ratio was varied from 0% to 6% SO2(v/v) in air and similar Mn removals were achieved at 0.75% to 3% SO2 at pH 3. The solution pH was varied from pH 2 to pH 4; Mn precipitation did not increase considerably from pH 2 to pH 3, but increased significantly at pH values higher than pH 3. Cobalt co-precipitation also increased as pH increased, with 1% Co co-precipitation at pH 3. An increase in temperature from 30°C to 60°C also increased Mn precipitation and 100% Mn precipitated at 50°C. Cobalt co-precipitation also increased significantly with an increase in temperature. An activation energy of 25 kJ/mol was calculated from the Arrhenius plot, which is an indication that the precipitation reactions were both chemically and diffusion controlled. XRD analysis showed that Mn precipitated in the form of Mn2O3 instead of MnO2 that was predicted from thermodynamic data. SEM and XRD analysis also revealed that the precipitate consisted mainly of gypsum or bassanite (99%), with the Mn containing phase (< 1%) distributed within the gypsum phase. The co-precipitated Co reported to the Mn phase. Keywords: manganese precipitation; SO2/O2 gas mixtures; cobalt solutions.

Jan 1, 2009

By K. Yathavan

Fracturing of rock at low stress levels can be a source of unexpected problems in rock engineering: • the resulting instability can be a safety hazard; • in very brittle rocks it may be associated with violent failure of the rock and strainbursting (rockbursting); • it usually leads to an unexpected requirement for rock support, with time and cost implications; • in rock boring projects, it may result in fracture of the rock ahead of the bored face and in the walls of the bore behind the face. This may lead to cutter head vibration, increased cutter wear and consequently decreased performance and increased costs. Examples of situations in which fracturing of rock at very low stress levels has been observed will be described. This will include details or estimates of the in situ stress magnitudes and the rock strengths involved. La brisure de roche sous faibles contraintes peut être l’origine de problèmes inattendus en génie minier : • L’instabilité résultante peut devenir un danger • Elle peut provoquer des éclatements violents des roches fragiles • Elle nécessite souvent une infrastructure de soutien de la roche, ayant des implications sur les coûts et les délais • Les forages de la roche peuvent provoquer une brisure de celle-ci au niveau de la surface forée mais ainsi à l’intérieur de la roche, causant parfois des vibrations et une fatigue de la tête de forage, induisant une baisse de performance et un accroissement des coûts. Nous avons décrit ci-après des exemples de situations de brisure de roche sous faibles contraintes. Cette description comprend des détails ou des estimations des forces et des contraintes impliquées. Cette étude représente la base du travail de recherche effectué sur le phénomène. ißbildung im Gestein unter niedrigen Stressbedingung kann eine mögliche Ursache sein für unerwartet auftretende Probleme in der Felsmechaniklehre: • Die resultierende Instabilität stellt ein mögliches Sicherheitsrisiko dar; • In sehr sprödem Gestein kann es verbunden sein mit einem plötzlichen und gewaltsamen Zerfall des Gesteins; • In den meisten Fällen ist eine nicht eingeplante Gesteinsabstützung erforderlich, und damit ein Zeit- und Kostenaufwand verbunden; • Bei Bohrungsprojekten kann es dazu führen, daß es während des Bohrvorganges zu einer Rißbildung im Gestein hinter und vor der gebohrten Felswand kommt. Dies kann Bohrkopfvibrationen, eine erhöhte Bohrkopfabnutzung und folglich eine Bohrleistungssenkung, sowie Kostenerhöhung zur Folge haben. Das Phenomen von Gesteinsrißbildung unter niedrigen Stressbedingung wird anhand von einigen dokumentierten Beispielen erörtert. Diese beinhalten zudem Details oder Schätzungen bezüglich der Stärke des in situ Stressfeldes, sowie der gegebenen Gesteinsstärken. Die mit diesem Beitrag dokumentierten Ergebnisse formen eine Grundlage zur weiteren Forschung dieses Phenomens.

Jan 1, 2003

By Huang Zhiwei, Paul Skayman, Kevin Holley

In 1989 The First Brigade for Geology and Mineral Exploration of Qinghai Province discovered gold at Jinlonggou and Qinlongtan, Tanjianshan. Between 1992 and 2002 small scale mining was carried out at these sites using underground mining methods at Jinlonggou and an open pit at Qinlongtan. During 2003 and 2004 geotechnical investigations were carried out in support of a bankable feasibility study. An important objective of this investigation was to meet both internationally accepted standards and codes of practice, and also to satisfy the Chinese requirements. Extensive use of local experience was utilised. Where possible geological drilling information was incorporated into the assessment. Extensive geotechnical mapping of surface and underground exposures, and index testing to gain an appreciation of rock intact strength were used to characterise the sites. Rock mass classification (MRMR) was used to assess indicative overall slope angles and appropriate bench stack heights for the proposed pits at Jinlonggou and Qinlongtan. Measured discontinuity orientations were used in kinematic analysis to assess stability of possible pit slope geometry at a batter and overall scale to provide preliminary recommendations for the pit slope configuration. Numerical modelling was also carried out to improve the understanding of anticipated pit behaviour. Site investigation and preliminary geotechnical design details, that incorporate site specific conditions for the formation of open pits at Tanjianshan, are discussed in this paper.

Jan 1, 2006

Mr G. Maude was educated at Huish&apos;s Grammar School (Taunton) and Leeds University. He graduated in 1961 with a B.Sc. degree in Mining. Mr E.B. Crocker was educated at Florida Park High School, Witwatersrand Technical College, and the University of the Witwatersrand.

Jan 1, 1985

By M. Somerville, S. Sun

The liquidus temperature and viscosity of a range of melter slags produced in South Africa were determined. Drop-quench experiments were carried out on the supplied plant samples to determine the liquidus temperature and phase relations at sub-liquidus temperatures. The temperature measurement range covered 1300°C to 1630°C. Results from these experiments show liquidus temperatures for the melter slags to be in excess of 1500ºC with the chromium containing spinel as the primary crystalline phase. At lower temperatures, an olivine or pyroxene phase co-existed with the spinel phase. The viscosity of the slags was determined over a temperature range of 1350 to 1550°C, under a controlled atmosphere. Results show two orders of magnitude variation in the viscosity (0.2 to 20Pa s) with strong effects of slag chemistry and temperature. Slags with lower SiO2and Cr2O3concentrations were more fluid. Slags with the lowest FeOx and highest SiO2concentrations were the most viscous. These observations are in accord with general behaviour of silicate slags. While the presence of a spinel phase may have an effect on the viscosity of the melter slags, results obtained to date indicate a much stronger effect due to the presence of an olivine or pyroxene phase at lower temperatures. Keywords: phase equilibria, liquidus, viscosity, slags, olivine, spinel, pyroxene

Jan 1, 2004

By M. R. L. Blackwell

Over the period 1964 to 1969 Conzinc Riotinto of Australia undertook and completed an evaluation of a large low-grade copper orebody on Bougainville Island in the Territory of Papua and New Guinea. From the outset it was clear that the geographic, climatic and topographic characteristics of the area would necessitate a heavy capital outlay on production and support facilities. Both the physical problems and the magnitude of the investment amplified the need for a thorough and rigorous evaluation of the various strategies for exploiting the orebody. In view of the number of independent and inter-related variables and the flow of new data, a computer-based evaluation process extended the scope and depth of the analysis considerably. The system used permitted an iterative assessment and re-assessment of the various strategies with the results becoming increasingly refined with time. This process encompassed the modelling of the orebody, the simulation of alternative operating strategies and the determination of the financial profitability of the project,

Jan 1, 2014

By Y. Wang, S. Sridhar, B. Coletti, G. N. Shannon, S. Vantilt

The final removal of inclusions in the ladle, tundish, and mold in a continuous casting process involves the kinetic steps of liquid film drainage, interface rupture, and absorption of the inclusion into the overlaying molten slag. During this process, oxide inclusions can undergo chemical reactions with the slag. This paper presents recent results on imaging the slag/steel interface and elucidates the evolution of Al2O3and Al2O3-CaO inclusions during their separation from the steel and on their incorporation into the slag. Experimental results, obtained through a Confocal Scanning Laser Microscope, are compared with thermodynamic predictions.

Jan 1, 2004

Toxic gases, mostly carbon monoxide (CO) and nitrous oxides (NOx), are invariably generated by commercial explosives under practical conditions of usage because of oxygen unbalance and non-ideal chemical reaction. Permitted explosives are statutorily required to meet the criteria stipulated by regulatory authority for their toxic fume quality for their safe use in underground coalmines. Solid blasting using P5 explosives contribute around 60% production from Indian underground coal mines. Low pull and yield per blast in solid blasting has been identified as a reason for low production and productivity of Indian underground coal mines. In an effort to improve performance of solid blasting, it was envisaged to apply air decking between suitable P5 explosives using high density polyethylene (HDPE) spacers under a Ministry of Coal, Government of India funded project. A non-deflagrating slurry explosive composition having high air gap sensitivity was specially developed for this purpose, so that air decked cartridges get detonated sympathetically with single priming. However, statutory authority in India apprehended that the use of oxygen negative HDPE spacers can influence the generation of toxic gases. The effect of using HDPE spacers on the generation of toxic gases was studied under simulated laboratory conditions with newly developed as well as with three commercial P5 explosives. The results of studies presented in this paper revealed that the level of carbon monoxide increases linearly and there is no significant effect on the level of oxides of nitrogen due to the use of HDPE spacers with selected explosives. Studies also revealed that this newly developed slurry explosive can be used for air decking up to 15 cm using HDPE spacers of weight not more than 21 g without exceeding the permissible limits for toxic gases.

Jan 1, 2008

Book review AUSTRALIAN MINERAL INDUSTRY REVIEW FOR 1970 The Review is prepared by the Bureau of Mineral Resources, Geology and Geophysics, and gives an interesting and up-to-date account of the Australian minerals industry.

By X. H. Zhang, J. G. Cai

This paper discusses the behaviour of large-span tunnels and caverns in hard rock in a major underground storage project. In-situ stresses were measured using hydraulic fracturing during site investigation and 3-D overcoring during construction, with both showing a horizontal stress ratio of 2-3 times the vertical stress. Rock reinforcement design was based on the Q-system combined with numerical modelling for special design cases. Tunnel design and performance were checked and monitored by in-situ instrumentation during rock excavation, including measurements of deformation, convergence, and load on rock bolts. Deformation measurements using borehole extensometers included one borehole drilled into the virgin rock before rock excavation, which provided a direct and very insightful comparison with the various deformation measurements made during rock excavation. These measurements coupled with numerical calculations have proven that the high horizontal stresses to be very favourable to the stability of the large openings.

Jan 1, 2003

By John Freer

As an innovation on the annual programme, the Excursions Sub-Committee organized a social get together of the Institute&apos;s Councillors and their families on Sunday, 27th February, 1983. Asian Mining - change of date The Second Asian Mining Conference, previously announced as being held in Manila, The Philippines, from 5th to 8th November, 1984, will now be held in Manila from 11th to 14th February, 1985.

Jan 1, 1983

By M. L. Mahlatji

Mechanical alloying of an equiatomic mixture of crystalline Ti and Pt elemental powders in a high-energy ball mill formed an amorphous alloy by solid-state reactions. Mechanical alloying was carried out in an argon atmosphere at a rotation speed of 1200 r/min and a 20:1 ball-to-powder weight ratio, for time intervals of 4 to 40 hours. At an intermediate stage of mechanical alloying, scanning electron microscopy showed the formation of characteristic layered structures of inhomogeneous composition within the powder particles. X-ray diffraction analysis showed the gradual disappearance of crystalline Bragg peaks and the emergence of broad amorphous maxima as milling progressed. The amorphization process was completed after 8?12 hours. The amorphous state of the product indicated that temperatures during processing did not exceed the crystallization temperature of the alloy.

Jan 1, 2014

By M. Hao, S. Hu, X. Lyu, M. Lian, C. Anning, G. Yao, Z. Wang

The results revealed that the pozzolanic activity of the gold mine tailings and their main mineral phases improved by mechanical activation. Under the same activation conditions, the activated mica powders possessed the highest pozzolanic activity index, followed by the activated feldspar, and the activated quartz exhibited the lowest pozzolanic activity index. The addition of calcium oxide promoted the formation of amorphous C–(A)–S–H gel for all paste samples, and stratlingite and hydrotalcite were observed in calcium oxide activated mica paste. The addition of natural anhydrite promoted the formation of ettringite for the pastes of calcium oxide activated aluminosilicates materials (gold mine tailings, mica, and feldspar). Furthermore, the pozzolanic activity indexes of the mechanically activated gold mine tailings and their main mineral phases were tested to be qualified for use as supplementary cementitious material in cement. This paper provided an innovative approach for recycling gold mine tailings as supplementary cementitious materials in cement, which would be environmentally friendly and cost-effective. Keywords: Mechanical activation, gold mine tailings, supplementary cementitious material, hydration properties, pozzolanic activity

Jan 1, 2020

Cutting strong rock with a drag bit assisted by high-pressure water jets By M. HOOD. B.Sc. Hons. (Min. Eng.). B.Sc. (Mech. Eng.). A.M.I.M.M. (Visitor) Experiments are described that led to the discovery that coherent high-pressure water jets directed immediately ahead of drag bits while they are cutting strong rock reduce the magnitudes of the forces on the bits significantly. Tests were carried out to assess the effects of the pressure of the water jets on bit-cutting performance. The pressure was varied between 10 MPa and 50 MPa, the water flow rate being a constant 30 I/min. Over this pressure range, the force on the bit was reduced to the extent that the depth of cut of the bit was at least doubled with the point of impingement of the jets optimized. Forces on the bit were found to be particularly sensitive to the point of impingement of the water jets relative to the bit. The optimum configuration was found to be with two jets, one directed towards each corner of the bit and impinging on the rock approximately 2 mm ahead of the leading edge of the bit. Experiments in which a drag bit and high-pressure water jets were used to cut strong abrasive quartzite in the underground mining situation have demonstrated a potential increase of up to five times in the average depth of cut due to reduction of the forces on the bit. The results from the underground tests indicate that the life of the bit is improved significantly - by a factor of approximately two - when highpressure water jets are used.

Jan 11, 1976

By G. P. L. van der Linde

EVERY OREBODY IS UNIQUE [ ] GEOLOGY AND MINERALIZATION DIFFERENT [ ]

Jan 1, 2005

By S. Jeon, J. Kim, H. Lee

Though the importance of the engineering rock mass properties such as deformation modulus, cohesion and friction angle is emphasized, the researches on the reliability of these values are rarely performed. By using modified Takagi-Sugeno (TS) fuzzy inference system, a fuzzy model was developed based on the data obtained from domestic tunnel construction sites, and the ability of prediction was compared with the empirical equations conveniently used for estimating these values, which finds that fuzzy model is better than empirical equation. Sufficiently large database, however, is required for training the fuzzy model for more accurate prediction. Obwohl die Wichtigkeit der technischen Eigentümer der Felsenmassen wie zum Beispiel Verformungsmodulus, Bindekraft und Reibungswinkel betont werden, wird die Forschung auf der Zuverläßigkeit dieser Werte selten durchgeführt. Mit modifiziertem Takagi Sugenos (TS) Flaumigenschlußsystem wird die Flaumigenmodelle von den Daten, die von inländischen Tunnelbaustellen erhalten werden, entwickelt. Zum Schätzen dieser Werte ist es viel günstig, Flaumigenmodell zu benutzen, als zu adoptieren die empirische Gleichung für die Fähigkeit der Voraussage. Genügende große Datenbank wird aber zum Ausbilden flaumigen Modells für genauere Voraussage erfordert. Quoique l&apos;importance sur la caractéristique d&apos;ingénierie de la masse de roche comme le module de déformation, la cohésion et l&apos;angle de friction, soit soulignée, la recherche sur la confiance de ces valeurs est rarement effectuée. Avec le système modifié de Takagi-Sugeno(TS) fuzzy inférence, le nouveau modèle fuzzy s&apos;est développé. Après avoir estimé sa valeur, nous pouvons savoir que ce modèle fuzzy, basé sur les données venant du chantier de construction de tunnel national, est mieux que l&apos;équaton empirique. Pourtant plus de données de base sont indispensables pour produire le modèle fuzzy plus précis.

Jan 1, 2003

By J. W. Latilla, J. J. van Wijk

A running facebreak ahead of the powered support units occurred on the number 4 seam at Matla Coal’s number 3 shaft (Matla 3) in April and May 2002.Very difficult mining conditions were experienced for a distance of some 150 m in the tailgate and to a lesser extent on the face itself. The paper analyses the main causes for the high stress conditions leading to the facebreak, namely, the existence of a >20 m dolerite sill close to surface and the effect of stopping longwalling on the overlying 5 seam. Difficulties experienced during the facebreak are discussed, including, pillar and roof collapses in the tailgate, high stress areas ahead of the face causing roof and sidewall stability problems, flushing of broken rock into the face area at the tailgate, secondary mid-face breaks, and the availability of critical support units. Successful rock engineering interventions and learning points were that, a goaf angle of 14.6° was found to be more realistic than the previously used 20 to 25° in predicting dolerite sill behaviour in this area, pre-split blasting of the sill significantly reduced stress on the face and tailgate allowing re-support work to proceed, varying pillar support types were analysed and rated, the need to always have a ground control “First Aid” kit available was recognised and a strategy for subsequent panels beneath the sill was developed. Numerous support units were used and the performance of the more suitable types is briefly discussed. A running facebreak ahead of the powered support units occurred on the number 4 seam at Matla Coal’s number 3 shaft (Matla 3) in April and May 2002.Very difficult mining conditions were experienced for a distance of some 150 m in the tailgate and to a lesser extent on the face itself. The paper analyses the main causes for the high stress conditions leading to the facebreak, namely, the existence of a >20 m dolerite sill close to surface and the effect of stopping longwalling on the overlying 5 seam. Difficulties experienced during the facebreak are discussed, including, pillar and roof collapses in the tailgate, high stress areas ahead of the face causing roof and sidewall stability problems, flushing of broken rock into the face area at the tailgate, secondary mid-face breaks, and the availability of critical support units. Successful rock engineering interventions and learning points were that, a goaf angle of 14.6° was found to be more realistic than the previously used 20 to 25° in predicting dolerite sill behaviour in this area, pre-split blasting of the sill significantly reduced stress on the face and tailgate allowing re-support work to proceed, varying pillar support types were analysed and rated, the need to always have a ground control “First Aid” kit available was recognised and a strategy for subsequent panels beneath the sill was developed. Numerous support units were used and the performance of the more suitable types is briefly discussed. Une cassure de taille en avant des unités de soutènement s’est produise sur la veine numéro 4 dans le puits numéro 3 (Matla 3) de la mine Matla Coal en avril et mai 2002. Les conditions d’extraction étaient extrêmement difficiles sur une distance d’environ 150 m dans la voie de tête et, en moindre mesure, sur le front de taille lui-même. L’étude présente analyse les raison majeures pour les conditions de grandes contraintes qui ont conduit à la cassure de taille, à savoir l’existence d’un mur de dolérite de >20m proche de la surface et l’effet d’arrêter la longue taille sur la veine 5 superposée. Les difficultés rencontrées pendant la cassure de taille sont rapportées, y compris les effondrements de piliers et toit dans la voie de tête, les aires de grandes contraintes en avant du front de taille causant des problèmes de stabilité pour le toit et les parois latérales, l’injection de roches cassées dans la taille en voie de tête, les cassures secondaires à mi-taille, et la disponibilité d’unités de soutènement critiques. Interventions minières réussies et leçons apprises furent : un angle de remblai de 14.6° était plus réaliste que celui de 20 à 25° utilisé auparavant pour prédire la conduite du mur de dolérite dans cet endroit ; tir à deux temps du mur a réduit considérablement les contraintes sur la taille et la voie de tête, ce qui a permis un travail de support complémentaire ; des types variés de support de piliers furent analysés et évalués ; la nécessité d’avoir toujours une trousse de première urgence disponible fut reconnue ; et finalement une stratégie pour les panneaux en dessous du mur fut

Jan 1, 2003

By N. C. Steenkamp

Clay minerals are present in ores and their colloidal behaviour in slurries impacts on the full metallurgical process from comminution to the tailings storage facility. Geotechnical classification of tailings has been based on parameters such as grain size. This paper proposes that this parameter does not consider rheology and plasticity, and, while. Atterberg limits are useful, they do not consider other aspects such as active clay and chemical porewater.

Apr 8, 2026

By H. Urata, K. Ishii

To determine the effect of F ions in the molten alkali silicate systems on their structures, quenched Na2O-SiO2-NaF systems were investigated by Raman spectroscopy and molecular dynamics simulation. The systematic increase of 1100 cm-1band intensity in the Raman spectra of the silicate melts accompanying the replacement of F for O provides the evidence for concomitant polymerization of melts. From the molecular dynamics simulation, it was confirmed that most of substituted F was mainly coordinated to Na+ ions but not Si4+ions. These results were consistent with the mechanism in which F associated with otherwise network-modifying Na rather than with network-forming Si. Since F was associated to Na+ ions, the replace of O ion by two F ions promote the polymerization of silicate melts. Keywords: fluorine; molten flux; slag structure; molecular dynamics simulation; Raman spectroscopy.

Jan 1, 2004

1. New books Australian Institute of International Affairs. Uranium - energy source of the future? Canberra, thelnstitute (Box E181, P.O., Canberra, A.C.T. 2600, Australia), 1979. 202 pp. A$4,95 (postage 50c). Euroeconomics. The steel industry in Western Europe.. industrial and financial indicators. Paris, Eurofinance (9 Avenue Hoche, 75008 Paris, France), 1979. 167 pp. FF4,500 (Available in English and French.) M. B. Piggott. Load-bearing composite materials. Oxford, Pergamon Press, 1979. $15,00. J. H. E. Olaf. Automation and remote monitoring and control in mines. Essen (West Germany), Verlag Gliickauf GmbH, 1979. 200 pp. DM36. (In English.) J. P. Jenkins and E. T. Brown (eds). KWIC index of rock mechanics literature. Oxford, Pergamon, 1979. 742 pp. £60. R. J. Wakeman (ed.). Progress in filtration and separation 1. Amsterdam, Elsevier, 1979. 346 pp. Dfl.llO,OO. 2. New journal As from 1980, Coal Calendar is being published as a separate monthly periodical. 3. Proceedings L. E. St Pierre and G. R. Brown (eds). Future sources of organic raw materials. Oxford, Pergamon, 1979. 612 pp. £22,50. P. Haasen, V. Gerold, and G. Kostorz (eds). Strength of metals and alloys. Oxford, Pergamon, 1979. 3 vols., 1800 pp. $200. K. J. Miller and R. F. Smith (eds). Mechanical behaviour of materials. Oxford, Pergamon, 1979. 3 vols., 1800 pp. U.S.$200. 4. Tax relief? The Publishers&apos; Association of Great Britain recently issued a circular to a number of professional bodies drawing their attention to a court decision in favour of tax allowances on the purchase of textbooks. In January Electroheat The International Union for Electroheat, which com. prises a score of highly industrialized countries, every four years organizes a congress at which experts discuss the technicalities and economics of the latest applications of electroheat in industry and other sectors. Corrigenda: March issue The following amendments should be made to Table II of the paper &apos;Commodity analysis:

Jan 1, 1980