Search Documents

By Jeff Poe

When a takeup weight is offset to the side of a conveyor, a wire rope is commonly routed from the takeup weight through a series of sheaves to the takeup carriage. The friction developed from a series of wire rope sheaves can effect the actual belt tension at the make up carriage. Through real-mime testing the actual tension on a makeup carriage was recorded with data acquisition using an internally strain-gauged turnbuckle. The wire rope used to transfer the makeup weight to the makeup carriage was routed through a series of lubricated bronzed bushed sheaves. The tension on the makeup carriage was found to be as much as 26% higher than the weight of the makeup due to the friction in the sheaves. A detailed discussion of the testing and results will be made.

Jan 1, 2000

By Robert E. Goodwin

There are four main requirements which must be considered when selecting a wire rope for the best serviceability. A proper choice is made by correctly estimating the relative importance of each of these requirements and selecting s rope which has those qualities best suited to withstand the combination of destructive forces expected under continued service. A wire rope should possess: 1. Strength sufficient to support the maximum load expected and with s proper safety factor. 2. Ability to withstand bending and to resist bending fatigue without failure of the wires. 3. Ability to withstand surface abuse such so abrasive wear, pounding, and wire scrubbing. 4. Ability to withstand abuse such as crushing and distortion.

Jan 1, 1968

By Joseph F. Peters

The paper will begin with the physical parameters of design in a wire saw. These will include such things as the type of wire used, abrasives, horsepower of operation, and drive components. It will then go into the many uses of wire sawing in the quarrying and finishing of granite. This will include a step by step program of the removal of a block unit of granite from the quarry site through the finished slabbing and jointing in the plant. After this, there will be a small insertion of possibilities of wire sawing techniques in underground excavation work. This would be speculative only. I will use the example of powerhouse type of excavation work given to me by Dr. John Reed, and try to explain how I would attack this type of work using wire saws. Several slides of both design criteria and actual installations were shown.

Jan 1, 1997

By E. J. Rorem

Rockfall and unstable rock slopes can be con-trolled by using steel wire-rope net systems as barriers or as slope draping. The chief advantage of such systems over rigid type barriers is the flexibility of wire rope netting. This flexibility and strength permits kinetic energy dissipation with low maintenance requirements. Mining activities can produce temporary or long-term unnatural slopes and unstable rock faces that may produce rockfall hazards. Such conditions can necessitate efforts to minimize the hazard to workers, structures and equipment.

Jan 1, 1996

By K. Zabrusky

"Wireframe construction is an integral part of resource estimation. Wireframes control domaining of samples and data for geostatistical analysis and grade estimation. They may also provide 3D representations of lithology and grade domains. Thus, the way in which a wireframe is constructed has implications throughout the resource estimation process. Proper construction technique and understanding of wireframing processes should be a high priority in a model workflow. Herein is presented an overview of two main categories of wireframes: implicit and explicit. Construction differences between these two types are highlighted. Factors affecting the choice between the two wireframe types will be discussed, including data quantity, data distribution, and sampling technique. Deposit geometry also plays an important part in wireframe construction. The role of geologic knowledge, cross section orientation, and deposit type in regards to wireframe construction will be discussed. The effect of wireframe type on resource estimation will be examined. Finally, best practices for creating meaningful solids that contribute to a reasonable grade estimation are outlined. INTRODUCTION Wireframes are essential to many types of resource estimations. They provide a way to delineate a deposit into various domains. Domaining can be done by lithologic or geologic units, structures or structural zones, or by grade. Domaining is important for geostatistical analysis and grade estimation of a deposit. The purpose of domaining is to analyze and estimate like data with like. Grade distribution patterns may vary by lithology or by proximity to or existence within structural zones. Properly constructed wireframes are therefore a fundamental necessity to a properly executed geostatistical analysis and resource estimation model. The choices made in construction of wireframes have a trickle-down effect on the entire model and should be made according to best practices for the deposit type at hand.TYPES OF WIREFRAMES Explicit The term “explicit wireframe” is used in this paper to indicate wireframes that are constructed by the modeler. This usually involves the modeler drawing the wireframes “by hand”, e.g. still utilizing some sort of computer aided drawing software, but with the modeler making all decisions about the size, shape, and positon of the wireframe. These wireframes are drawn based on some type of key variable that the modeler determines is important to their system. Often, this key variable may be a lithologic unit that controls mineralization, an observable structural zone, or a grade cutoff. Explicit wireframes are generally constructed as a series of shapes drawn on 2D planes or cross sections that are then connected into a 3D shape. Figure 1 shows an example of an explicit wireframe that was drawn based on a grade cutoff on 2D sections (Figure 1a), then joined into a 3D shape (Figure 1b)."

Jan 1, 2015

By R. Heersink, C. H. Wells

Innovations in communications and real-time information systems are providing industry opportunities to improve profitability. Real-time operating data is collected from equipment across a site or even several sites into a central server for secure PC and PDA-based Internet access. This paper includes discussion of how operating staff can use wireless devices to see equipment and processing data from anywhere throughout the mines and concentrators, and how management can view results from multiple mines, all in real time. Additional opportunities enabled through the remote access by equipment vendors or mining consultants is also presented, as well as an overview of typical benefits and current installations.

Jan 1, 2002

By R. Bissonette, C. Sunderman, R. Jacksha

The ability of wireless systems—e.g., voice communication, proximity detection, tele-remote operation, telemetry, etc.—to function satisfactorily (coexist) in the presence of other wireless systems is critical to the safety and health of mine workers. The failure of wireless systems to coexist could result in the delay, corruption, or outright loss, of critical data, voice, or video information. However, no mining-sector-specific regulations, standards, or guidelines exist to ensure the safe coexistence of wireless systems. This paper introduces the concept of wireless coexistence, implications in the mining industry, and the National Institute for Occupational Safety and Health’s (NIOSH’s) research approach to develop guidelines and recommendations to ensure safe wireless coexistence.

Feb 1, 2023

The Virginia Center for Coal and Energy Research has been developing models of wireless signal propagation in underground coal mines since 2007. The current mine propagation modeling software, named COMMS, is able to locate potential broadcast points for underground wireless mesh systems and estimate their coverage. COMMS utilizes programmed routines to calculate necessary values to both quantitatively and qualitatively solve and analyze predicted coverage areas. The program approximates the spatial relationships that are encountered, such as ventilation regulators, belts and other obstructions. Using this model for propagation allows the optimal communications node locations to be calculated, by using lessons learned from current installations and experience with the new technology. In addition, the optimization can be calculated by checking all possible combinations of broadcast locations. This paper compares these optimization calculation methods. The ability to solve a mine?s communication network provides a pre-installation mine network design map, creates coverage maps of the mine and allows planning for future communication activities

Jan 1, 2011

By Raphael Victor

The construction and modification of tunnels brings a requirement for precise measurement of convergence and divergence to safeguard the structure, maintain safety and provide the assurance needed to maintain efficient progress. Established methods include manual measurement using tape extensometers and automated methods using photogrammetry and automated total stations. Drawbacks include the need for frequent access, power supply, cabling, and cost. The paper describes how the development of reliable optical displacement sensors (ODS) has changed the landscape. ODS sensors are connected to a long-range wireless mesh communications network via a solar-powered gateway outside the tunnel, with data instantly transmitted to the internet. A sensor and its reflector target can be installed in 20 minutes and is maintenance free for a decade. Tunnel movement is measured to sub-millimeter precision with repeatability of ±0.15 mm. Integration of a triaxial tilt sensor allows slope distance to be converted to horizontal and vertical changes and allows rotational movement to be determined. Applications include new-build and long-term structural health monitoring. Case studies will be given, including the refurbishment of rail tunnels in Spain where the ODS measured movement during track lowering in a situation where no other automated system was considered viable.

Jun 13, 2023

By Ed Schodowski

Wireless technology is a hot topic for anyone involved in the design, operation, maintenance or upgrading of mines or mineral processing plants because wireless technologies overcome barriers that have prevented many useful data inputs. Wireless communications can contribute to worker safety, satisfy environmental concerns, support plant security, track human and physical assets, and improve equipment maintenance. The cost structure of wireless is compelling and users can realize savings ? up to 90 percent less installed cost than wired instruments ? since wireless technology eliminates the need for expenses associated with cabling, engineering, construction and documentation. Many applications previously considered too expensive have become economically feasible with wireless. Two examples are continuous monitoring of safety showers to notify operators when one has been activated, and monitoring effluents to ensure environmental regulations are being met. In many cases, wireless transmitters can be installed where wired devices were too expensive to justify, or were not feasible due to physical or technical barriers. Examples include monitoring temperature measurements inside a rotating reactor or monitoring process variables in a tough, corrosive environment too challenging for a wired solution. Wireless also gives operating personnel mobility with the ability to communicate from remote or hard-to-reach zones. According to a recent Venture Development Corp. survey covering radio frequency (RF) of microwave industrial monitoring and control products, these features are contributing to the expected nationwide growth rate for industrial wireless applications of 19 percent annually from 2007 to 2012 (Taylor, 2008). At the same time, mineral producers have many questions about wireless systems including their applicability, reliability and security in this industry. Just what can wireless do? Is it secure and reliable? Can these instruments stand up to the rigors of the industry? Can wire-less technology provide the flexibility needed for mining applications?

Jan 1, 2009

By Tim Neil, O&apos

Copper price rebounds A worldwide scramble for diminishing supplies of copper has pushed the red metal's price to more than $2.20/kg ($1 per lb), the highest level since 1980. The first nine months of 1987, world copper production was down 1% from a year ago, while consumption rose 7%. Demand has been fueled by economic strength in several countries, particularly Japan, South Korea, and Taiwan. The price has also been helped by interest rate declines that have prompted manufacturers to build up inventories. In addition, China is expected to be a major buyer in 1988 as it stocks up for its five-year industrialization plan. There appears to be no sign of any significant increase in copper supplies until later 1988 or early 1989. This means supplies probably will remain tight for some time even if world economic activity slows. Strikes and other production problems slowed world output of copper in 1987. As a result, copper supplies are the lowest they have been in 14 years. World inventories currently total 625 kt (690,000 st). That is not much above the 585 kt (645,000 st) level reached in 1974 when the price of copper rose to a record $3.84/kg ($1.74 per lb). This makes all the more interesting what Chile, the world's largest copper producer, has been doing lately. Chile has been the world's largest copper producer since 1982, when it overtook the United States. Table 1 shows Chile's copper grades, reserves, and production at its mines. Chile contains roughly one-fifth of the world's copper reserves. At present production rates, these reserves would last for more than 100 years. In 1986, Chile produced 1.4 Mt (1.5 million st) of fine copper, up 3%. Chile accounted for 17% of the world's copper output.

Jan 1, 1988

By Larry H. Heflin

The Washington Metropolitan Area Transit Authority's Wheaton Station and tunnel design was completed and offered for bid in the Spring of 1983. The format was unique to the Authority: a four part, four fiscal year contract developed in response to funding limitations with construction divided into four stages allowing the maximum amount of work to be done each year for the funds available. The bid was based on the entire contract, but was orginally awarded for only the first year's work. Each year's work had a maximum funding limitation thus safe guarding the Authority from a grossly unbalanced bid. The Authority's estimate for this work was $83,871,524. The low bid came in at 61% of this for a total low bid of $51,512,058. The low bidder was ILBAU America Corporation whose home offices are in Austria. Following receipt of the bids (and resolution of objections cited by other bidders who felt that the job could not be done for the $51 Million dollar figure), a Notice-To-Proceed was given on October 5, 1983. The construction contract allows a Value Engineering Change Proposal, called a VECP which is initiated and developed by the contractor to change the drawings, specifications or other requirements of the contract. Among other things the VECP should decrease the contract price while maintaining the service life, reliability, ease of maintenance, and standardized features and appearance and not require an unacceptable extension of the contract time. A VECP must estimate the amount of the net savings

Jan 1, 1985

By Lyman File

This paper discusses the overall challenges to construct a two-lane highway tunnel located in southwestern Colorado on U.S. Highway 160 for the Colorado Department of Transportation by the Kiewit Western Company. The purpose of this project is to provide the excavation and temporary support for a highway tunnel 280 m (916 feet) long. The tunnel cross section is 14.3 m (47 feet) wide by 8.5 m (28 feet) high, 105 m2 (1,130 SF).Construction methods include conventional drill and blast excavation with rockbolt and shotcrete ground support. This unique tunnel is being constructed under alpine tunnelling conditions and in the immediate vicinity of active highway traffic.

Jan 1, 2003

By Weibai Hu

The flotation separation of wolframite from fluorite and quartz is investigated with chelating agents and neutral oil as synergic collectors. Test results indicated that a-nitroso-ß-naphthol has a strong collectivity for wolframite and selectivity against fluorite and quartz. The 8-hydroxyquinoline has collectivity and selectivity also. They both have a better activity than sodium oleate. However, the cupferron is slightly inferior. The synergism of chelating agents and neutral oil looks promising, especially for fine wolframite particles. The activation effect of Fe2+ and Ca2+ ions on separation of wolframite from fluorite and quartz is slight. The UV absorb-spectra measurements showed that the adsorption of chelating agent on wolframite is multilayer, and flotation behavior is related to chemisorption. The chelating agent which bonds to Fe and Mn sits on the wolframite surface, and the reaction between Mn2+ ion with collector is more significant. The essentials affecting reagent activities are the bonding factor and the hydrophobic factor. These factors are discussed by structure-activity relationship theory. The synergism of neutral oil is a secondary collector likely to lengthen the hydrocarbon chain of chelating agents.

Jan 1, 1985

By Ken Santini, Ronald R. Bauer, Joseph R. Copeland

Wollastonite, named after W.H. Wollaston, an English chemist and mineralogist, is a calcium metasilicate having the chemical formula CaSiO2. Although it is a unique mineral, wollastonite has a short history of industrial use. Wollastonite is the only naturally occurring, nonmetallic, white acicular mineral. Its acicularity is the main reason for its ascendancy in the late 1970s and 1980s as a reinforcing filler and as a replacement for short-fiber asbestos and short-fiber milled fiberglass. Wollastonite is used in applications ranging from bowling balls to automobile fenders, from ceramic tile to automobile brakes, and from thermal insulation board to protective industrial coatings. The United States is the largest producer of wollastonite, with China, India, and Finland as the other three major sources. The United States, Europe, and the Far East are where most of the production is consumed. Geology Mineralogy and Physical and Chemical Properties Wollastonite, a member of the pyroxenoid mineral group, has the theoretical composition of 48.3% CaO and 51.7% SiO2. Iron, manganese, magnesium, or strontium may substitute for some of the calcium. Commonly associated minerals include garnet, diopside, calcite, quartz, epidote, apatite, and sphene. Some of the physical properties of wollastonite are listed in [Table 1]. Wollastonite is largely chemically inert; however, it can be decomposed in concentrated hydrochloric acid. Some wollastonite will fluoresce under shortwave or longwave ultraviolet light, or both, with colors ranging from pink-orange to yellow-orange and, more rarely, bluish green. In addition, wollastonite may show phos¬phorescence. Because of its unique cleavage properties wollastonite breaks down during crushing and grinding into lath-like or needle-shaped particles of varying acicularity. This particle morphology imparts high strength and is therefore of considerable importance in many of the markets for wollastonite. The acicularity of particles is defined by their length:width, or length:diameter, ratio (i.e., aspect ratio). Individual particles, even the smallest ones, commonly ex¬hibit an aspect ratio of 7:1 or 8:1 and have an average diameter of 3.5 gm. Low aspect ratio products (powder wollastonite, or milled grades) with 3:1 to 5:1 aspect ratios are used as general fillers, in ceramics, and in metallurgical fluxing. High aspect ratio products with ratios of 15:1 to 20:1 are used as functional fillers for rein¬forcing thermoplastic and thermoset polymer compounds and as a replacement for asbestos. The dry brightness and whiteness of wollastonite are also important in determining its suitability for certain filler and ceramic applications. When pure, the mineral is brilliantly white, but impurities may color it cream or gray. Brightness is determined by measuring the reflectance of finely ground powder against a stan¬dard that is assigned a brightness of 100. Magnesium oxide and barium sulfate are the two standards used. G.E. brightness, a term used in North America, refers to brightness measured with a Gen¬eral Electric reflectometer. Commercial wollastonite products usu¬ally have a G.E. brightness ranging from 85 to 95. The Hunter method is also used to measure the brightness of wollastonite. Loss on ignition (LOI), another important property in determining applications for wollastonite, is the amount of volatile matter driven off when the mineral is heated to 1 000°C. Com¬mercial wollastonite products have an ignition loss ranging from 0.5 to 2.0%. Wollastonite's naturally high pH of 9.9 (10% water slurry) is of major importance to its use in the coatings industry. Coatings formulators use milled grades as a pH stabilizer in interior and exterior PVA (polyvinyl acetate) and acrylic latex paints. There are two polymorphs of calcium silicate: wollastonite, a low-temperature form, and pseudowollastonite, a high-temperature form. Conversion of wollastonite to pseudowollastonite occurs at about 1 120°C and results in an increase in the coefficient of expansion and a color change. Pure white wollastonite may change to a cream tint or to various shades of red or brown. This color change is thought to be due to the presence of iron and/or strontium.

Jan 1, 1994

By Ronald R. Bauer

Wollastonite is a little known industrial mineral of the silicate group. The largest and purest known deposit in the free world is being mined and beneficiated in Millsboro, New York by NYCO, A Division of Processed Minerals Incorporated. The associated garnet and diopside are separated from the wollastonite using dry high intensity magnetic separators. Beneficiated wollastonite is used extensively as an additive and filler in the ceramic, paint, refractory, and wallboard industries. Wollastonite acts as a functional filler due to its unique chemistry and physical acicularity.

Jan 1, 1982

By F. Scott Carpenter

During the past several years, more frequent reference to Wollastonite has appeared in print, both in this country and abroad. The reason for this is the apparent growing interest in this mineral as it approaches commercial maturity. Twelve years ago, wollastonite was available in only limited commercial quantity. In 1933, a deposit in California was worked for a short time to provide a calcium silicate raw .material for the manufacture of mineral wool* It was not until the spring of 1953 that Cabot Corporation put into operation a modem commercial plant to produce this material in a variety of grades. These grades covered both a range of particle size and of particle shape. At that time, applications for wollastonite were largely speculative, although a few commercial applications in glass frits and welding fluxes did exist, For all practical purposes, it was a new material for which few commercial uses had been fully proven.

Jan 1, 1964

By Claude Hébert

The Grenville structural province, a 400 km-wide belt of Precambrian metamorphic rocks which crosses the province of Québec in a northeasterly direction, is the host of several wollastonite occurrences. Most of these are found in marble and calc-silicate rocks enclosed within or located near intrusive bodies. Reconnaissance and detailed mapping of such zones have helped to identify areas of interest for wollastonite exploration. The most important zone is located in the huge Lake Saint-Jean anorthosite massif in the central part of the Grenville. A recent geological mapping project has revealed the presence of wollastonite in metasedimentary faulted remnant of the roof. The main occurrence consists of diopside and wollastonite in a zone at least 3 km long and 150 m wide. Preliminary sampling suggests and average grade of 50 percent wollastonite with an aspect ratio of 151. Other wollastonite deposits occur in the western part of the Grenville, mainly north and west of Montreal, where the Morin anorthositic complex and a large syenite mass intrude the metasedimentary rocks of the Grenville Supergroup. Marble bands with up to 70 percent wollastonite occur locally at the southern margin of the complex or as an inclusion in the syenite. Significant wollastonite occurrences have recently been found in the eastern part of the Grenville. One of them is located in metamorphosed calcareous rocks which are part of the granulite facies Manicouagan metamorphic complex. A representative sample analyzed 54 percent wollastonite. Farther south, an inclusion diopside-wollastonite gneiss containing an estimated 40 percent wollastonite occurs at the margin of the Pentecôte River anorthositic complex.

Jan 1, 1995

By S. M. Robinson

Wollastonite is recognized as one of the most unique, non-metallic minerals in the world. Its history for use in industrial applications is recent compared to other minerals, however, its distinctive physical properties, such as acicular particle shape, and alkaline pH creates incorporation possibilities ranging from bowling balls to automotive fascia, from ceramic tiles to automotive brakes, and from thermal insulation board to industrial and trade sale coatings. Its future use will be impacted by the exploitation of deposits which will ensure maintenance of the acicularity and purity of this naturally occurring mineral. Additionally, closely held surface treatment technology will open up additional niches requiring highly engineered performance.

Jan 1, 1995

By Christopher J. Hall

It has been known for a long time that summing pressure drops and rises due to friction, shock, fans and natural ventilation is incorrect. In fact, lost works and works should be summed. In spite of this, the traditional method of finding a fan/system operating position has been the H/Q Curve. This paper presents (lost) work/m curves, progressing from a single fan moved around the system to include natural ventilation work, and fans in a series, parallel and series/parallel. The solutions obtained graphically are substantiated by dry air thermodynamic solutions, and the traditional solutions are shown to be in error. This method of solving problems is particularly useful when moving fans around the system, and essential in series/parallel and series situations with substantially different fan densities. The dry air analysis is employed because of its simplicity. Real air, with evaporation and condensation, will react somewhat differently, and one should use real densities (i.e.[l + w +w]/va ) when using this method. One source of error when applying this method to real air, although probably not major, will be investigated in a subsequent paper. Friction and shock losses are proportional to the square of the mass rate of flow, leading to the typical parabolic system curve. However, the unbalanced water stuff potential energy term, on a unit mass basis, is substantially independent of the mass rate of flow. It is possible that this could be handled as a negative natural ventilation work.

Jan 1, 1987