Search Documents

By J. M. Keane

SMEThis loaner is concerned with important criteria relative to the design of small flota¬tion concentrators. For the purpose of this discussion a small flotation concentrator is defined as a facility having a designed ore feed rate of 1,000 metric tons per day (MTPD), or less. The decision to design and construct a small flotation concentrator is the culmination of a series of logical steps relative to the ex¬ploitation of a potential ore body. The information required for a rational and timely decision regarding plant design and construction is usually contained in a feasibility report. The information required in a thorough feasibility report has been summarized (1) (2) as follows: Type of mine or plant and proposed daily, monthly, and yearly production of all intermediate and final products. Quantity of indicated ore reserves. Location of project illustrated by a map showing surroundings, trans-portation facilities, and existing utilities.

Jan 1, 1980

By R. D. Begley

This paper will present detailed design drawings of a flexible single floor residential superstructure proposed for both longwall and room and pillar mining conditions. All efforts were made to provide an immediately available economical alter- native for future home builders on subsidence prone land. Based on this fact, a basement was not included in the design because additional costs and measures would be required to minimize cracking and leakage. A cost comparison with a traditional superstructure demonstrated that this would be a cost effective alternative. The criteria used to determine the design of the residential structure was as follows: 1. The appearance should not be different then a typical three bedroom residence; 2. Only commercially available devices and present architectural and engineering technology should be used to achieve the required "flexibility" of the super- structure; 3. The structure as completed would be capable of resisting a predetermined amount of vertical and horizontal movement; and 4. If the structure was to experience stresses beyond its capabilities, it could be easily removed from the foundation and releveled.

Jan 1, 1986

By M. Karmis

Subsidence planning and control must be an integral part of mine design in order to minimize the economic impact of underground mining on the surface. Pre-calculation of surface deformations which may cause damage to surface structures must be performed and dam-age criteria must be established, if the response of structures to such movements is to be determined and the extent of damages to be assessed. In this paper the Surface Deformation Prediction System (S.D.P.S.), which can be used to predict accurately the vertical and horizontal parameters of surface movements due to underground mining, is discussed. The Subsidence Response Modeling Program (S.R.M.P.). which can be applied to evaluate the response of buildings to subsidence-induced movements, is also reviewed. Finally, an example is presented demonstrating the applicability of these techniques for subsidence design and control.

Jan 1, 1990

By William W. Shriver

When the Henderson Project is completed in 1975, it will become one of the Free World's largest primary molybdenum producers. The Henderson Mine will be located approximately 50 miles west of Denver, Colorado, on the eastern slope of the Continental Divide. Ore reserves are currently estimated to be 303,000,000 tons with a grade of 0.49% MoS2. The mill and tailing area will be located approximately 14.5 miles from the mine in the Williams Fork Valley, which is on the western slope of the Continental Divide. Ore haulage from the mine to the mill will be by ten miles of underground railroad and 4.5 miles of surface railroad. The concentrator has been designed to mill 30,000 tons per day and will yield approximately 50,000,000 pounds of contained molybdenum per year. This paper is concerned with the tailing and water supply system for the Henderson Project and in particular the environmental considerations affecting their design.

Jan 1, 1970

By Michael J. Lehnen

Slurry diaphragm walls are commonly used as both temporary excavation support walls, and permanent structural walls, for circular shafts and long rectangular structures (such as underground subway stations); however, they are not commonly used for more compact rectangular or square shafts. In these instances, a second wall is typically cast inside the slurry walls to form the permanent structure. This paper discusses the approach used on the Silicon Valley Rapid Transit Project in California to analyze these compact rectangular types of structures for static and seismic loading, and to determine whether or not slurry walls can be confidently used as both the temporary and permanent walls for two tunnel ventilation shafts.

By Charles A. Stone, Eric C. Wang

"Top-down wall construction was selected to excavate the tunnel portal headwall areas of the ORB East End Crossing tunnel. Benefits included an expedited construction schedule realized by staging excavation and rock support with development of temporary construction access roads. Rock mass properties, proximity to right-of-way lines, and blasting impacts were considered to design suitable lift heights, intermediate bench locations, and permanent ground support systems to provide supported permanent excavations. Carbonate rock formations contained adverse subsurface geotechnical features including solution cavities, clay seams, weathered joints, pinnacled rock, and boulders, which were addressed by flexibility in design. The resulting over-break conditions and long-term water infiltration issues required economic design solutions. This paper discusses the unique considerations required during design of top-down tunnel portal headwalls excavated in carbonate rock formations including temporary excavation and permanent ground support systems which provided flexibility for unforeseen over-break, minimized construction delays, and provided long-term stability. PROJECT BACKGROUND The East End Crossing is an approximate 8-mile highway connection of the Louisville-Southern Indiana Ohio River Bridges East End Crossing (ORBEE) project. Currently under construction, this connection will link State Road 265 in Indiana with the Gene Snyder Freeway in Kentucky to form an outer loop bypassing the Louisville-Southern Indiana metropolitan area. This highway project features a 2,510-foot long, three-span cable-stayed bridge over the Ohio River, and a 1,680-foot long tunnel. The project, being managed by the Indiana Finance Authority and Indiana Department of Transportation, is scheduled to open to traffic by the end of 2016. The new twin three-lane tunnel under the historic Drumanard Estate requires steep cut excavations for approach and tunnel portal walls on the order of 60 feet deep through overburden soil and carbonate bedrock formations. This paper focuses on the design considerations for the permanent support of the top-down wall construction of the tunnel portal headwalls and approach retaining walls."

Jan 1, 2016

By A. Bumanis, K. S. Bawa

INTRODUCTION A rail rapid transit system called the "Metro" system is presently under construction in the Nation's Capital area. The agency responsible for the design and construction of the Metro system is the Washington Metropolitan Area Transit Authority, an independent tristate organization set up under an Act of Congress and financed by federal, state, and local public funds supplemented by revenue bonds. When completed, the Metro system will comprise nearly 100 route miles. About fifteen percent of this mileage is now under construction, while designs for the-remainder are in progress. The system is scheduled for completion in about eight years at a cost of approximately 3 billion dollars. The Metro system will involve nearly all types of construction generally used for rapid rail transit projects. About half of the mileage will be underground, comprising approximately 16 miles of rock tunnels, 10 miles of earth tunnels, and nearly 21 miles of cut-and-cover construction in earth (see Figure 1.). The remaining 51 miles of the system is planned to be constructed on the surface as at-grade or elevated structures. The system includes 86 passenger stations, 53 of which will be underground structures. Twelve of the underground stations will be large size chambers in rock while other underground stations will be constructed in earth as cut-and-cover structures. Thus, about one-fifth of the system will be designed as underground structures, namely tunnels and stations, in rock. Such designs in rock resulted from the existence of bedrock (schistose gneiss) at reasonable depths generally in the north and northwest

Jan 1, 1997

By K. Chandrasekaran

Carbon-in-leach (CIL) is conventionally used in gold processing operations when preg robbing components are present in the ore. The CIL process is becoming attractive even in other situations when preg robbing is not a factor. This article discusses the situations in which the CIL circuit can be applied. The results of leach-carbon-in-pulp (CIP) and CIL circuits at Newmont Gold's Mill No. 2, No. 4 and No. 5 are presented for comparison: Mill No. 4 was initially designed for a throughput of 4.1 kt/d (4500 stpd). It is presently operating at an average throughput of 6.6 kt/d (7300 stpd) without significant changes to the original design. The design considerations of the Mill No. 4 CIL circuit are discussed. The design of any processing facility represents a series of decisions. The final design options should ultimately be resolved based on economic as well as technical considerations. Every design decision represents some sort of compromise. From the designer's view point, these decisions are made with the conviction that the final product represents the most prudent long-term expenditure. The design throughput rate is a decision reflecting a maximum return for the capital and operating costs that the plant will incur over the life of the mineral resource. The result is a plant that is not operator proof or maintenance free because it would be too costly to build. At some point, the incremental increase in the level of capital expenditure would not adequately compensate for the lower

Jan 1, 1991

By K. Chandrasekaran

Carbon-in-Leach (CIL) is conventionally used in gold processing operations when preg robbing components are present in the ore. CIL process is becoming attractive even in other situations when preg robbing is not a factor. This paper discusses the situations in which the CIL circuit can be applied. The results of Leach/CIP and CIL circuits at Newmont's Mill No.2, 4 and 5 are presented for comparison. Newmont's Mill No. 4 was initially designed for a throughput of 4500 tons per day. The mill is presently operating at an average throughput of 7300 tons per day without significant changes to the original design. The design considerations of the Mill No.4 CIL circuit are discussed.

Jan 1, 1991

By S. Bozinis

In this paper, blast design considerations and implementation that lead to reduced vibrations will be presented. In addition, blast vibration data collected during hard and semi-hard rocks blasting in the proximity of an inhabited area will be analyzed and presented. In all cases maximum vibration levels are kept below the limits set by DIN 4150.

Jan 1, 2006

By H. Colijn

Feeders are used to provide a means of control for the withdrawal of bulk materials from storage units, such as bins, bunkers, silos and hoppers. This control function can only be performed properly as long as the bulk materials flow by gravity to the feeder in a uniform and uninterrupted fashion. A feeder can do many things, but it should never be considered a suction pump: During the past few years various papers have been written and presented on feeders and their application. 1,2,3,4,5,6,7,8,9)* It is not the intent of this paper to cover the same ground, and the readers are therefore ad¬vised to consult the referenced publications for supplementary information. This paper will be confined to some specific design criteria of bin feeders, such as feeder load and power requirements. Special attention is given to the basic design criteria of vibratory feeders.

Jan 1, 1968

By C. R. McKee

In-situ mining of hard rock deposits will only become successful as we understand the engineering parameters involved and the design limitations they impose. As recognized by Wadsworth1 the most critical area is the enhancement of permeability in a hard rock mass. Along with creating permeability, the appropriate flow and fragment size conditions must be generated to insure economic rates of mineral recovery. In this article our interest is confined to true in-situ processes in which boreholes are drilled from the ground surface or a mine drift to deeper strata. We assume that fractures and permeability enhancement will be due to explosives detonated in boreholes. Other techniques such as hydraulic fracturing do not produce the necessary size distribution to promote economic extract ion rates unless the medium is already highly fractured and interconnected. Notable exceptions where hydraulic fracturing is applicable are many oil, gas and salt deposits. For many in-situ processes, an array of explosive charges offers the opportunity of creating a distribution of many fractures not achievable by other techniques. Such a situation would be suitable, for example, to in-situ mine hard rock gold, uranium, copper or oil shale deposits and may enhance oil and gas recovery in certain situations. The purpose of our article is to review and extend the explosive permeability theory of McKee and Hanson 3,4,5 and to apply its results to derive design parameters suitable for in-situ mining.

Jan 1, 1981

By T. McKeon, G. Luttrell

Spiral separators are commonly used to upgrade sand-sized particles in both the coal and mineral processing industries. Many plants utilize multiple stages of cleaning and/or scavenging spirals to improve recovery and/or final product grade. Field studies suggest, however, that the layout of industrial spiral circuits is often less than optimal. This oversight can usually be attributed to a failure by plant designers to consider fundamental process engineering rules that govern the layout of complex separation circuits. This article reviews some of these important rules as specifically applied to multistage spiral circuit design. Two industrial case studies, one involving the upgrading of heavy mineral sands and a second involving the cleaning of fine coal, are presented to illustrate the impact of good design protocols on spiral circuit performance.

Jan 1, 2007

By L. B. Guo, S. S. Peng

A hybrid boundary element-finite element model was formulated to model roof-bolt reinforcement of roof strata with bedding planes. This model was used to analyze the stress distribution around a rectangular opening, with variables such as opening width-height ratio, number of bolts installed, number1 location of bedding planes, in-situ stresses, etc. The most critical areas are identified, and the number and length of roof bolt required are then determined. Two case examples are illustrated.

Jan 1, 1991

By S. S. Peng

A hybrid boundary element-finite element model was formulated to model roof bolt reinforcement of the roof strata with bedding planes. This model was used to analyze the stress distribution around a rectangular opening with variables such as opening width-height ratio, number of bolts installed, number/location of bedding planes, in-situ stresses, etc. The most critical areas are identified and the number and length of roof bolt required are then determined. Two case examples are illustrated.

Jan 1, 1989

By T. C. Bibb

Longwalls using shearers in seam heights of less than 1.2 m (48 inches) are relatively rare in the U.S. Westmoreland Coal Company is currently operating a shearer-equipped longwall at a cutting height of 1.17 m (46 inches) in its Bullitt Mine. This face has averaged 2795 metric tons/day of operation since its startup on April 3, 1984. Longwall productivity in thin seams is substantially impacted by equipment reliability and availability of useable working room for travel and access. This paper addresses the design criteria used in selecting this face equipment, with the goal of maximizing these two parameters. Equipment discussed includes shearers. face conveyor, shields, stageloader, and emulsion system.

Jan 1, 1985

By D. E. Traut

A fluidized countercurrent ion-exchange system was developed, operated, and evaluated by the Bureau of Mines. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows are continuous except for short periods when resin increments are withdrawn. The exchange of uranyl sulfate between a simulated acid leach uranium solution and a strong-base, ion-exchange resin together with the subsequent elution with an acidified sodium chloride solution was studied. The effects of the number of sections, section heights, amount of resin withdrawal, and solution flow rates were investigated. Also examined were the kinetic and equilibrium relationships for the absorption step. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable. The column was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1975

By Charles V. Riley

While the late 1960's are known as the years of the public recognition of impending environmental crises, the 1970's will be known as the decade of public concern for improving the quality of that environment. One of the present major environmental concerns is the temporary disturbance resulting from coal surface or open cast mining. To realize that this concern will continue in the future, one need only observe the daily news media. Increasing energy demands in the U.S., a doubling of electrical power consumption each decade during the present century, and the projected needs for the remainder of the century are indica¬tions that coal surface mining as a major extractive industry will continue. Coal and lignite, prime energy resources and extremely abundant in these United States, in the face of seemingly limited gas, oil and uranium reserves, are both destined for expanded future use. Presently some extremely serious techno-logical and environmental problems are associated with the develop¬ment and use of nuclear power. It is true that the extraction and use of coal as an energy fuel poses disruptive problems for the environment, but the solutions to many of the problems are known or can be solved within a reasonable time framework. Certainly our national well-being and continued survival, as a free nation within the world community, automatically dictate the continued use of the coal resource for energy. Concurrently, those engaged in coal surface mining, with the temporary disturbance of the land and water resources, must also realistically conclude that public concern for maintaining and improving the quality of the environment will not diminish. Although as ecological, economic, social and aesthetic elements

Jan 1, 1972

By John W. Scott

INTRODUCTION The design criteria for a particular concentration and dewatering project will provide the formal basis for design of the process, equipment and facilities. These criteria will specify the required capacities and operating schedules for the equipment, as well as the quantity and quality of the feed to be processed and products obtained. The general climatic and geographical conditions at the site, specific information on soil or rock conditions; and applicable design standards and codes will also be included. The design criteria will generally be based on an interpretation of testwork carried out on the particular ore and site, and will thus parallel in detail and completeness this testwork. As the project moves from the early conceptual phases through to final detailed design, the design criteria will be developed and become more detailed as information is generated and made available for use. The design criteria are critical to the design effort as the formal specification to the designer of what and how much is to be processed, what and how much is to be produced, and where and under what conditions. The actual design criteria will be a formal tabulation of the design basis information developed for the project in question. For a preliminary study, this may consist of a single page of data; for a feasibility study several pages and for a detailed design up to several hundred pages and multiple volumes. Depending on the complexity of the process and the level of detail included, each project will be unique to some degree. The design process for a project normally progresses from preliminary conceptual phases through to a final detailed design. The criteria used for the initial concepts are generally developed from rough data and preliminary testwork on the ore in question. Regardless, the plant throughput and products are defined, thus giving a scope and definition to the study phase. In some studies a range of throughputs may be analyzed in order to arrive at the most economically attractive size for the proposed operation. This optimum size is then used as the design throughput for the more detailed design phases. Similarly as more testwork results are available and the ore characteristics and process become more well defined a continuous updating of the design criteria is undertaken.

Jan 1, 1986

By Aaron Archer, James Parkes

This paper presents design considerations for the major underground elements of the pending BCRUA Phase 2 Raw Water Delivery System Project. These elements include two Lake Taps; an 8,800 LF, minimum 10-ft OD intake tunnel; a suction chamber with 6 Pump Shafts; a 30-ft diameter, 300-ft deep Main Shaft; a 2,600 LF Transmission Tunnel with 78-inch steel liner; and a 130-ft deep shaft on the Transmission Tunnel. The tunnels and shafts will be excavated through the Glen Rose limestone. The design development included consideration for technical requirements, easements, third party commitments, previous local project experience, and constructability based on contractor outreach.

Jun 13, 2021