Search Documents

By J. Richard Kyle

The Pb-Zn ore bodies in the Pine Point district are localized in paleo-solution structures that developed as the result of post-middle Givetian subaerial exposure of the carbonate barrier complex. Sulfides are concentrated in transgressive pale-solution structures that acted as natural bypasses between aquifers and loci for mixing of fluids of different character, one of which contained metals and the other reduced sulfur. Complex ore textures indicate rapid early sulfide precipitation followed by slower sulfide growth. Evidence for both sulfide-carbonate equilibrium and disequilibrium conditions suggest fluctuations in ore fluid composition. District and ore body metal distribution patterns may reflect the nature and movement of mineralizing fluids.

Jan 1, 1979

By Jean-Michel Rendu

Accurate modeling of the semivariogram is an extremely important step in the geostatistical analysis of mineral deposits. Automatic fitting of a mathematical model is often possible but not necessarily desirable. Significant geologic and statistical information must be taken into account in the fitting process, which is not always available to the computer. Manual fitting of the model is, on the other hand, extremely time consuming. Interactive graphics are best suited to optimize the process. A number of interactive methods are described, which are adapted to the modeling of semivariograms in one-, two-, or three-dimensional environments.

Jan 1, 1982

By J. Y. Hwang

Alunite has been utilized as raw materials for producing alumina and potassium sulfate fertilizer in Russia for many years. In the United States, this mineral has not been commercially processed though reserves of 5 to 10 billion tons of alunite ore have been estimated. Major constituents of these ores include quartz and alunite. The minerals are finely intergrown and liberation occurs below 10 microns. Adequate separation techniques for such fine particles have not been developed. A new method for the beneficiation of alunite ore is proposed in this study. 'Ibis method utilizes a small amount of fine magnetite upon which the liberated quartz is selectively flocculated. The co-flocculated magnetite and quartz are then separated from the alunite in a high gradient magnetic separator. Clean products, e.g. an alunite concentrate of 90% grade with 80% recovery, has been obtained from an Utah ore. Techniques for the selective co-flocculation of magnetite and quartz, the separation of the carried quartz, and the recovery of magnetite after separation are discussed.

Jan 1, 1985

By CHONG WEI, TATYANA KATSAGA, DEREK APEL

This study provides an effective determination process of the interface microstructural parameters in the numerical modelling of the mechanical interaction between two different geomaterials involved with frictional-bonded interfaces, such as the interaction between backfill columns and the surrounding rocks, or the soil-structure interaction, by using the coupled finite-difference and discrete-element (FD-DE) method. Three-dimensional numerical direct shear tests were conducted on the coupled FD-DE model of the combined rock-cemented rockfill (R-CRF) specimens with the frictional-bonded interface. With the microstructural parameters determined, the macro-mechanical properties of the interface of the coupled model were calibrated to well fit with the theoretical values of the combined specimen under the direct shear condition assumed according to the Mohr–Coulomb strength criterion. Evident elastoplastic shear behaviour was observed on the interfaces, and excellent agreement was attained between the shapes of the theoretical and simulated shear stress-displacement curves of the coupled models at different servo-controlled normal stresses. Particulate-scale force chains inside the DE model of the CRF specimen were highly consistent with the force contour on the FD model of the rock specimen, demonstrating the shear stress evolution of the coupled model at different shear displacements. Parametric studies verified the effects of the deformation properties of the interface parallel bonds on the shape of shear stress-displacement curves of the coupled models. The test results validated the feasibility and rationality of the coupled FD-DE method for modelling the combined specimens with frictional-bonded interfaces or joints. Furthermore, this study provides valuable numerical modelling experience for investigating the shear behaviour at the interface between cemented backfill columns and surrounding walls by using the coupled FD-DE method.

Nov 2, 2021

By Paul K. Edwards

The forces of nature have concentrated sand at various geographical locations that are being mined and processed for a large variety of industrial uses. While most operations serve a number of industries, this paper deals only with the foundry requirements. The forces that have decomposed a source rock, transported this material and redeposited it, have created two general types of sand. These types are classified as the (1) Lake and Bank Sands and (2) Silica Sands. The Lake and Bank sands will contain 92 to 94% Sio2 while silica sands are in excess of 98.5% Si02 and most of the producers wash these sands to up grade their products to 99.5% or better. Included in the Lake and Bank sand would be the river sands that are used primarily for construction purposes. The Foundry Industry is broken down into three types of castings : 1. Grey Iron Foundries The grey iron castings largest market is the automotive industry in Ohio, Northern Kentucky, Indiana, Illinois and Michigan. These castings are poured at temperatures ranging from 2400° to 2700°F. The Silica Sands or the Lake and Bank Sands will satisfy the requirements of the grey iron castings. There are 2 ½ to three million tons per year shipped from the state of Michigan far grey iron castings by the Lake and Bank Sand Producers.

Jan 1, 1974

By Helmut Goehring

Surface mining has been used primarily where deposits of minerals were exposed or close to the surface. Surface mining can, therefore, be considered the oldest branch of mining. As the most accessible deposits became uneconomical because of the lack of suitable high capacity conveying systems, deep mining took its place. Only in the twentieth century was this trend reversed as high capacity production and conveying systems were developed. This rapid development was triggered by the steadily increasing demand for raw materials and fossil fuels, as well as by the ever increasing ratio between overburden and deposits.

Jan 1, 1982

By Atta Ur Rehman, Kwame Awuah‑Offei

This paper examines the effect of bucket geometry (cutting blade profile, floor profile, and blade thickness), speed, motor power output, and muckpile particle sizes on bucket penetration and draft for rubber tire loaders. The work uses a 1:16 scaled model of a load-haul-dump in full factorial experiments to examine the effect of the variables on penetration and maximum draft. The results show that speed and motor output are positively correlated to penetration and draft; muckpile particle size is positively correlated to penetration and negatively correlated to draft (p < 0.0014). The results show that buckets with a semi-spade cutting nose profile yield the highest penetration (mean 118.30 mm) followed by those with the spade (mean 108.88 mm), which also yield higher penetration than those straight blades (mean 95.19 mm). Bucket floor profile and blade thickness had no significant effect on penetration or draft. Also, we determined that increasing the speed and motor power output, simultaneously, can reduce bucket penetration. Thus, operators should not waste energy for no additional gain or even loss in bucket penetration. Also, the work finds speed and motor power output each combine with muckpile particle sizes to affect bucket penetration. This research furthers our understanding of the effectiveness of different bucket geometries in improving penetration and reducing draft for rubber tire loaders.

Oct 29, 2021

By T. Simpson

European industrial policy seeks to provide the right framework conditions to allow companies to develop and innovate and to make the EU an attractive place for job creation. This includes providing the basis for a competitive manufacturing industry which provides around 20% of EU economic output and employment for about 34 million people. The EU non-energy extractive industry with an annual turnover of around ?40 billion and a direct workforce of about 270,000 people is considerably smaller, but it plays a vital role in providing much of the manufacturing sector with raw materials. It also supplies very large quantities of minerals such as aggregates and natural stone to the construction industry, facilitating the development of modern infrastructure such as roads, railways, houses, schools and hospitals. However, despite an active extractive industry, Europe is increasingly dependent on imports of raw materials and particularly metallic ores and concentrates. In 2005, the trade deficit for minerals was in excess of ?11 billion, of which ?10 billion related to metallic minerals. Such import dependency is not a new phenomenon, but the rapid industrialisation of developing countries such as China and India has significantly increased global demand, resulting in large price increases for downstream industries and at times, bottlenecks in supply. The impact of this and other competitive pressures on some sectors of the European manufacturing industry, including the possibility of them being lost to lower cost countries outside Europe, has moved the issue of industrial policy and access to raw materials up the political agenda. A number of measures have already been announced by the European Commission to address these issues including: - The analysis of the competitiveness of individual industrial sectors, in order to understand their specific needs and take account of the particular opportunities and challenges they face.

Jan 1, 2006

It is well established that the results of emulsion flotation in which water-insoluble oily collectors are utilized depend critically on the emulsification of the collector and on its conditioning with the pulp prior to flotation. The flotation tests carried out with magnesite and fluorite using sodium oleate as collector confirmed acidic and alkaline ranges of good flotation. While the flotation results in the acidic solutions depend strongly on the conditioning time and can be very much improved when longer conditioning times are utilized, the tests in the alkaline environment do not exhibit any significant dependence on conditioning. The results obtained with sodium salts of myristic and lauric acids confirm these findings. The observed effects provide additional evidence for the role of the colloidal species which appear in the acidic solutions of weak electrolyte type surfactants, such as fatty acids. The flotation properties of sodium oleate in the pH region in which it appears in the form of oleic acid droplets are mainly determined by the properties of such droplets. The flotation in this pH region closely resembles an emulsion flotation.

Jan 1, 1993

By R. R. Rollins

Field data combined with theoretical derivations were used to design a surface mining operation using explosive casting. Calculated casting results varied from 44 to 65% depending on bench height. This model was then applied to field tests at an eastern, contour, coal stripping operation. Results from five experimental casting shots are summarized and compared to conventional mining methods. The overburden material removed by casting ranged from 35 to 65% with an average of 50%. Fragmentation was improved and it was demonstrated that this procedure is economically attractive with a resultant cost savings of $.59/m3 or $5.93/t of clean coal.

Jan 1, 1987

By Charles H. Arnold, Timothy Fallara, David A. Day, Paul H. Marshall

The Upper Scioto West Interceptor Sewer (USWIS), Parts 1 and 2, consists of approximately 7,128 meters (23,385 ft) of 328 cm (129 in.) diameter tunnel. The project ex-tends from the City of Dublin to Griggs Dam in the City of Columbus. The majority of the tunnel was designed for excavation in rock by TBM. The remaining portions span pre-glaciation formed valleys in-filled with glacially-derived sediments. Tunnel construction in one of the glacial till filled sections includes excavation by drilling and controlled blasting. The other section will be constructed by ground consolidation followed by excavation by TBM. This paper describes the methods employed to mine the glacial till filled valleys.

Jan 1, 1997

By D. R. Nagaraj

Secondary Ion Mass Spectroscopy (SIMS) was used to study adsorption of sulfide collectors such as modified thionocarbamates and thioureas, xanthate, dithiophosphate, and dithiophosphinate, on galena, chalcocite, chalcopyrite, and quartz under flotation related conditions. In the case of the adsorption of modified thiourea on chalcopyrite, chalcocite and Cu-activated quartz, and of dithiophosphinate on galena, SIMS measurements have provided direct evidence for the presence of metal-collector (1:1) complexes on surfaces. In the other systems, only the collector molecular ion and its fragments were detected. The distribution of adsorbed species on the surfaces was obtained by using SIMS in the imaging mode. On chalcopyrite, only the copper-collector complex was found; there was no evidence for iron-collector complex. In the case of quartz, adsorption of selective collectors was observed only after activation by copper ions.

Jan 1, 1996

By R. W. Bruce

The normal practice for processing complex sulphide ore has been to grind with steel balls and/or rods in steel mills before flotation. Little thought had been given to the effect of grinding media on flotation selectivity of copper-lead -zinc ore until 1960 when Rey and Formanek(1) published their experiments on sphalerite floatability after grinding in a porcelain mill with ceramic pebbles. The studies by Rey and Formanek had a pronounced effect on the milling of copper-lead-zinc ores in Canada and possibly throughout the world at a time when autogenous grinding was creating a great deal of interest. The impression was created, and possibly still exists with some mill men, that grinding an ore in the absence of steel will result in a loss of selectivity between copper, lead and zinc minerals. This is in spite of the fact Rey and Formanek&apos;s experiments showed that the "naturall floatability" of sphalerite was not apparent after grinding in a porcelain pebble mill in an alkaline pulp.

Jan 1, 1976

By T. M. Gurr

In response to concerns voiced by local, state, and federal agencies and various environmental groups, the Central Florida Phosphate Industry and various governmental agencies have been investigating methods to accelerate the consolidation of waste clays generated during phosphate washing and beneficiation processes. The objectives of research efforts have been to reduce the storage volumes required for clay waste, accelerate reclamation and to return the land to approximate pre-mining topography. Government and industry research to accelerate waste clay consolidation has evolved two general methods: gravity thickening and chemical flocculation. Gardinier, Inc. one of the phosphate mining companies, evaluated the use of synthetic (polyacrylamide) flocculants as an alternate waste clay thickening method in response to mining conditions encountered at their Fort Meade Mine and the proposed North Hardee County extension of the Fort Meade mine (Figure 1). After considerable research and evaluation, the Alsthom-Atlantic Clariflux Super-flocculation method was chosen by Gardinier, Inc. as a method to seriously consider for use at their Fort Meade mine.

Jan 1, 1986

By H. T. McAdams

The logic of regression analysis as an operations research tool is critically examined, and a formal basis for its application to mining problems is developed. The traditional view of regression analysis as a statistical discipline does not provide an adequate basis for evaluating a regression model in a specific area such as ore reserve calculation or process control. In particular, the validity of the residual-sum-of-squares criterion is questioned, and the need for a criterion based on interpolative features of the model is emphasized. Strictly speaking, a regression model is statistically supported only at points at which observations are available, yet inferences are drawn with regard to a continuum. When considered as a mathematical function, therefore, the model is observationally defined only on a domain consisting of a finite number of points. Extension of this domain to an interval of the real line must be based on physical rather than statistical argument. Vector space and function theory concepts useful as a logical framework for a physically oriented problem analysis are discussed and their usefulness demonstrated in a practical problem.

Jan 1, 1966

By Yueyue Ding, Yuanhui Li, Zhengrong Li, Pengfei Yu, Kunmeng Li, Zhipeng Xiong

The stress evolution and failure characteristics of overburden were studied during multi-stope mining for a gently inclined thin orebody. Firstly, an indoor physical experiment was conducted on the excavation of a multi-stope mine with an orebody dip angle of 20°. The results show that the vertical stress concentration area gradually shifts to deep-buried rock mass with the mining from shallow to deep buried stopes, resulting in shear failure originating from high stress. On the contrary, the pressure relief zone presents an asymmetric distribution characteristic that is biased towards the upper part of the goaf, resulting in large subsidence and tensile failure of the stope #1 and #2 roofs. Secondly, the numerical simulation model under the same geological condition was established to measure the roof deformation at different stages of mining. The numerical simulation results are in good agreement with the physical test results; the roof displacement is largest in stope #2, second-largest in stope #1, and smallest in stope #3. Finally, the evolution of deviator stress concentration, displacement field and potential failure zone of overburden under different orebody dip angles were studied. As the dip angle of the orebody increase, the deep-buried stope roof changes from deviator stress release to deviator stress concentration in different stages of mining, and shear failure is most likely to be induced when the orebody dip angle is 30°. Meanwhile, the closure displacement of the stope roof decreases gradually, while the tangential displacement increases, so the anti-sliding ability of the support bodies in the stope should be improved. The potential tensile failure zone gradually shifts from the center of the goaf to the upper part, and the deep-buried stope roof evolves from tensile failure to shear failure. Results of this research expected to provide guiding significance for stope support design to control roof deformation and failure, to ensure the safety of the stope.

Mar 2, 2023

By K. L. Kayler

Ball clay production in 1991 amounted to about 800 kt (880,000 st), about the same as in 1990. 1992 estimates show a 5% decrease to 750 kt (827,000 st). This decrease continued a trend of reduced production that began after the peak of 900 kt (1 million st) that occurred in 1988. Use of ball clay in sanitary ware was about 2% less in 1992, although levels of use in floors and wall tile, dinner ware and pottery remained constant. Filler, extender and binder applications continued to be important end uses, accounting for about 17% of total market. Refractory uses maintained their market share of about 17 kt (18,700 st). Use of clay liners in toxic and waste dumps is an application widely found in Germany. However, its use has not been fully exploited in the United States. This could represent an opportunity for domestic clay producers. Tennessee remained the leading source of ball clays. Other producers were Indiana, Kentucky, Mississippi and Texas. Tennessee&apos;s production, however, decreased about 3% in tonnage produced and its value dropped from 68% to 65% of total production. The ceramics division of Southern Clay Products, Inc., was bought from LaPorte plc by United Clays of Texas, Inc., a US subsidiary of Watts Blake Bearne & Co. The purchase included ball clay reserves at Troup, TX. The acquisition makes United Clays the second largest ball clay producer in the United Sates. United is also the only company mining clay in Texas. Fire clay production decreased 5%

Jan 1, 1993

By P. C. Kapur

For mineral processing spirals, mathematical force equilibrium models are sought to extend the spiral performance envelop. In Part 1 of this report, a complete geometric description of the helical spiral and its trough or channel contour is provided. The secondary circulatory fluid motion in the transverse direction that develops when water flows down a tightly turning curvilinear path and its implications for gravity separation are discussed. Different forces that act on the particle during its passage through the spiral are enumerated and quantified for a better appreciation of their relative contributions and roles in the separation process. Three force equilibrium models from the hydrology literature on sed iment transport are employed to simulate a typical spiral. While the results are promising in that the models mimic the broad performance characteristics of the spiral, what is needed is a more general spiral model taking explicit cognizance of the missing components essential to the spiral description. These are such components as centrifugal force and the steep tangential slope of the channel deck. Results of this latter exercise are deferred to Part 2.

Jan 1, 1996

By S. P. Girrens

A coupled finite element geomechanical- hydrology code is currently under development for application to the problem of predicting groundwater disturbances associated with mine subsidence. The structural-fluid coupling is addressed by calculating the subsided mine geometry, with emphasis placed on determining the strata disturbance and locating damaged regions, for input into a hydrology code, which determines localized volume flow rates and aquifer fluctuations. Benefits from coupling will be best realized when field measurements, an additional aspect of the study concurrent with analytical investigations, indicating the relationship between increasing rock strain and increasing permeability are incorporated into hydraulic material descriptions. Hydrologic and struc- tural calculations are presented to demonstrate computational capabilities applicable to mine subsidence

Jan 1, 1982

By Richard C. Mayberry

Phosphate reserves have been and still are a controversial subject. Some published estimates are particularly conservative and have caused concern in government and political circles that southeastern phosphates are a dwindling resource. "Ores and ore bodies" are a function of economics that relate to a time/demand factor. The history of phosphates and other mineral commodities is one of mineral deposits (resources) ever becoming ore (reserves) via a long term logic based on price, supply, and demand factors operating through time and improved technology. Projections indicate that southeastern phosphates are sufficient for several centuries of operations at present production rates.

Jan 1, 1981